A.
Components:
ECU, two transmitters, shock sensor LED indicator, siren, antenna and wire harness.
B.Technical parameters
Voltage:12V*3V Static current:<10mA Frequency: 315 or 433.92 MHz Siren SPL: 105~125 dB
Factory setting
Electric lock Active arm No engine immobilize Door trigger (-) No blink Baro lock Passive arm Engine immobilize Door trigger(+) Turn signals blink
Shock sensor installation (Mounted firmly)
Central locking system installation:
1. For the vehicle with original electric central door lock, check its triggering type (negative or positive), then connect wires as per wiring diagrams Fig.2 or Fig.3. 2. For the vehicle with central locking system , while the driver's door do not have motor, the other doors have motor. A new motor for driver's door is needed. Fig. 4. 3. For the vehicle with baro-lock, please change the jumper J1 at "Baro-lock" position of the ECU. Fig. 5. 4. For the vehicle without central locking system, please install one set central locking system to match with the car alarm system. Fig. 2.
To adjust this button clockwise to increase sensitivity. Red light flashing when impact detected. (Factory setting sensitivity is suggested)
Car Alarm System
D. Wiring diagram
Orange White Yellow Orange/Black White/Black Yellow/Black
Orange White Yellow Orange/Black White/Black Yellow/Black
ON signal OFF signal
Orange White Yellow Orange/Black White/Black Yellow/Black
ON signal OFF signal
Fig.1 Principle
Fig.2 Negative trigger
Fig.3 Positive trigger
Baro-lock unit
Shock sensor Orange Fuse 15A White Yollow Fuse 15A Wires to central locking system
Orange White Yellow Orange/Black White/Black Yellow/Black Orange White Yellow Orange/Black White/Black Yellow/Black
Green/Blue Main Wire
Brown (-)
Red/Blue (+)
Orange/Black White/Black Yollow/Black Black Red/Black Red
Turn signnals blink jump swtich
Turn signals blink No blink
Door lock switch
Fig 4. Positive / Negative trigger
Fig 5. Baro-lock circuit
GND Trunk release +12V battery Siren Turn signal Turn signal LED indicator Installation of LED indicator
The LED indicator should be installed on the dashboard Pink(+) Water Engine killer circuit
Trunk release circuit
Red/ Black(+)
Trunk switch
Pink Brown Brown
Motor lock
Antenna
INSTALLATION MANUAL
Green Yellow/Black Yellow Red Orange Blue White
Siren installation
Window closer (-) Engine killer circuit (-) Fuel pump cut (-) Trunk trigger (-) Footbrake(+) Door trigger(-)/(+) ACC (+) Tilt sensor (additional)
Original circuit of the car GND
Yellow White
Green Green
Black
* Important note: The siren can't be connected to +12V Please mount the siren downwards to prevent water.
Engine killer relay Installation of ECU 1. The ECU should be installed and fixed in a suitable position under the dashboard. 2. Connect wires according to the diagram properly.
Boot trigger (-) Footbrake circuit
Orange (+) Footbrake light Boot light Red (-) Boot switch
Footbrake Learning button Press and hold the learning button in the ECU, the LED indicator turns on. Press the lock button on the first transmitter, the LED indicator will flash once, then press the lock button on the second transmitter, the LED indicator will turn off. (During the learning program, please keep holding the learning button until the LED indicator turns off). The two new transmitters are OK.
Notes:
1.This unit is for 12V DC vehicle only. 2.This unit is to reduce the possibility of losing the vehicle by terrifying the thief and informing the owner of the vehicle status. 3.Please ask qualified engineer to install this unit. 4.The wiring should be kept away from high temperature and high voltage places. 5.The wire joints should be insulated.
We have achived ISO 9001 : 2000 & ISO/TS 16949 : 2002 certifications by Rheinland (Germany) Co., Ltd.
Door trigger circuit (-) or (+) ACC circuit ACC circuit
1)Negative door trigger (-) (factory setting) White (+) Circuit of car
circuit of car
Installation of antenna
Dome light
Blue(-)
Door switch
White (+)
1.Fix the antenna to the ECU as shown 2. Straighten and suspend the antenna
MANUFACTURED BY:
2)Positive door trigger (+)
Steelmate Co., Ltd.
http: //www.steel-mate.com
Installation of tilt sensor (addtional) Programmable functions
LED indicator Sensitivity adjustment: button Mount horizontally.
Dome light
Blue(+) Door switch
Stage 1 2 3
LED flash once flash twice flash thrice
Sensitivity low high highest
J1
J2
No engine immobilize
J3
Engine immobilize
J4
Notice: Please choose the correct trigger type accoring to the vehicle by changing the jump switch J4
Door trigger(+) Door trigger(-)
Electric lock
Baro lock
Active arm
Passive arm
PCI0198/A
