USER GUIDE

NCR P1535 POS ( 7761 )

Release 1.1

BCC5-0000-5054
Issue F
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. Product names mentioned in this publication may be trademarks or
registered trademarks of their respective companies and are hereby acknowledged.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks
of HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under the terms
and conditions of an agreement you have with NCR, NCR's copyright notice must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become
available. NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances,
photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR
office for information that is applicable and current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value of this book.
Please use the link below to send your comments.

EMail: FD230036@ncr.com
Copyright © 2016–2020
By NCR Corporation
Global Headquarters
864 Spring St NW
Atlanta, GA 30308
U.S.A.
All Rights Reserved
 i

Preface
Audience
This publication is written for hardware installer/service personnel, system integrators,
and field engineers.
Notice: This document is NCR proprietary information and is not to be disclosed or
reproduced without consent.

Safety Requirements
The NCR P1535 POS conforms to all applicable legal requirements. To view the
compliance statements see the NCR HSR POS Terminals Safety and Regulatory Statements
(BCC5–0000–5069).
Caution: The on/off switch is a logic switch only. The AC line voltage primaries are
live at all times when the power cord is connected. Therefore, disconnect the AC power
cord before opening the unit to install features or service this terminal.
Caution: UV Light — Avoid looking directly at UV Lights.

Lithium Battery Warning

Warning: Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type as recommended by the manufacturer. Discard used
batteries according to the manufacturer's instructions.
Attention: Il y a danger d'explosion s'il y a remplacement incorrect de la batterie.
Remplacer uniquement avec une batterie du même type ou d'un type recommandé
par le constructeur. Mettre au rébut les batteries usagées conformément aux
instructions du fabricant.

Battery Disposal (Switzerland)

Refer to Annex 4.10 of SR814.013 for battery disposal.

IT Power System
This product is suitable for connection to an IT power system with a phase-to-phase
voltage not exceeding 240 V.

Peripheral Usage
This terminal should only be used with peripheral devices that are certified by the
appropriate safety agency for the country of installation (UL, CSA, TUV, VDE) or those
which are recommended by NCR Corporation.
Warning: DO NOT connect or disconnect the transaction printer while the terminal
is connected to AC power. This can result in system or printer damage.
ii

Warning: DO NOT connect or disconnect any serial peripherals while the terminal
is connected to AC power. This can result in system or printer damage.

Grounding Instructions
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is
equipped with an electric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes and ordinances. Do not
modify the plug provided – if it will not fit the outlet, have the proper outlet installed by
a qualified electrician. Improper connection of the equipment-grounding conductor can
result in a risk of electric shock.
The conductor with insulation having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal. Check with a qualified electrician or
service personnel if the grounding instructions are not completely understood, or if you
are in doubt as to whether the product is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole
receptacles that accept the product’s plug. Repair or replace damaged or worn cords
immediately.
 iii

Out of Box Failure (OBF)

If you experience an out of box failure (OBF) during installation or staging related to a
missing, wrong or defective unit or item, simply provide NCR with a detailed
description of the issue and the item will be replaced free of charge. For assistance with
this process send an email to CustomerSat.Retail@ncr.com with the following details:
• NCR Sales Order # (Sales Order # are located on the box)
• Date of Product Installation
• Product Model #
• Unit Serial #
• NCR part # of defective/missing/wrong component
• Description of Failure (please be specific. For example: “display will not power on”)
• Customer/Requestor’s contact name, phone number and/or e-mail address
• Address to ship replacement part(s)
Transport the product n its original packaging to prevent impact damages.
If you do not have access to a computer, you may leave a voice message at: 1-800-528-
8658 (USA), or (International) +1-770-623-7400. When leaving a message, please provide a
phone number and/or an email address so NCR can contact you if additional details are
needed.
Note: Used equipment that experiences a failure does not qualify as an OBF and
should go through the NCR warranty process.

Warranty
Warranty terms vary by region and country.
All parts of this product that are subject to normal wear and tear are not included in the
warranty. In general, damages due to the following are not covered by the warranty.
• Improper or insufficient maintenance
• Improper use or unauthorized modifications of the product.
• Inadequate location or surroundings. Site installation must conform to guidelines
listed in the Site Preparation Guide document and the NCR Workstation and Peripheral
AC Wiring Guide (BST0-2115-53).
For detailed warranty arrangements please consult your contract documents.
iv

Returning Defective Hardware for Service

Use the following procedure to report/return defective hardware.
Call the NCR Customer Care Center at 1-800-262-7782 and have the following information
available when you place the call.
• Class/Model number of the defective equipment
• Serial Number of the defective equipment
• Equipment location in the store
• Description of the problem, including any system error codes, error condition, or
guidance to the area of failure.
The NCR Agent will provide you with a work order number, which serves as your
Return Material Authorization (RMA). Please provide the RMA on the outside of the
shipping box.

Note: A work order must be opened for each device that is shipped for repair.

References
• NCR P1535 POS (7761) Site Preparation Guide (BCC5-0000-5053)
• 7761 Service Guide (BCC5-0000-5055)
• 7761 Parts Identification Manual (BCC5-0000-5056)
 v

Table of Contents

Chapter 1: Product Overview

Introduction 1
Features and Benefits 2
Optional Features and Benefits 4
Mounting Configurations 5
Expansion Options 6
Customer Display Options 7
Right Side Features (Port A) 8
Left Side Features (Port B) 9
Scanner 9
Specifications 10
Operator Controls 13
Power Switch 13
Bezel LED 13
Label Locations 14

Chapter 2: Hardware Installation

Installation Restrictions 15
Installation Notes 15
Cable Restraint 15
Footprint 15
Power 16
Moisture 16
Magnetic Strip Reader (MSR) Cleaning 16
Biometric Cleaning 16
Hardware Platform Drivers 16
Ergonomic Workplace 17
Installing the Terminal 18
Connecting AC Power 22
Disconnecting the Power Cable 22
Connecting to a Network 22
Starting Up the P1535 Terminal 22
Installing a Transaction Printer 23
Installing a Cash Drawer 24
Second Cash Drawer Cable Connection 25
vi

Using External Connectors 26

RJ12 Serial Port 27
RJ45 Serial Port 28
LAN 29
USB 3.0 Compliant Ports 30
Cash Drawer (CD) Port 31
Installing the Power Supply 32
Removing Top Assembly 37
Terminal with Expansion 38

Chapter 3: Cleaning
Cleaning the Touchscreen 40
Cleaning the Cabinet 41

Appendix A: Product IDs

P1535 POS (7761) 1
 vii

Revision Record
Issue Date Remarks
A Feb 2016 First Issue
B July 2016 Updated for Release 1.1
Removed reference to VESA Mount
C May 2017 Added the following updates
• Quickserve 24V PUSB + 12V PUSB + Dual CD (24V) Expansion
• USB MSR with NCR Key
• Android OS
• 2x20 Double Byte Display
• Product IDs
D Mar 2020 Added Cleaning chapter
E Oct 2020 Updated cabinet cleaning procedures
F Nov 2020 Added “Programming the Scanner” section
Chapter 1: Product Overview

Introduction

The NCR P1535 is a Point-of-Sale (POS) terminal designed for the restaurant and food
service environment. The terminal utilizes a next generation Intel® Celeron™ Processor
N3160 (Quad core, 2.24 GHz). The highly efficient processor offers great performance,
but with lower power consumption for a more reliable design. The POS terminal comes
in a 15–inch display with a projected capacitive (PCap) touch screen.
1-2 Product Overview

Features and Benefits

Features Benefits
Intel® Celeron™ Processor Fast performance, powerful quad-core and very low power. Long life cycle
N3160 commitment from Intel.
(Quad core, 2.24 GHz).
Quad-Core Technology Integrates four complete execution cores in a single processor providing
advancements in simultaneous computing.
NCR Countertop Enclosure Fully integrated, low-profile, water, and tamper resistant housing for high
functional retail interaction.
15” XGA (1024x768) LED LCD Energy efficient and long life LED display. Excellent brightness, contrast,
Primary Display and color depth. Enables the proper display of high-quality graphics to
ease use and decrease training time for retail employees or to directly
engage the consumer.
Software–adjustable Brightness Better display characteristics for user as well as significantly increased
and Contrast Control for Main bulb life for main display.
Display
Integrated projected capacitive Flat front, zero bezel modern design. Capacitive screen offers greater
screen controller durability and display clarity with full multi-touch support.
SATA Flash Storage SSD Large capacity 40GB solid-state drive (SSD) 2.5” flash drive. Additional
Options capacities may be available. No moving parts for increased uptime and
better reliability.
Integrated Stereo, Speakers Provides high-quality feedback for user interaction.
System Management features Supports ACPI, SMBIOS, DMI, SNMP, WfM, and PXE. Also supports
metering, remote desktop, remote execution, BIOS update, system
inventory and asset management.
Recovery Tool Provides a dedicated recovery button for factory restore and site backups.
1 PCI Express Minicard Provides expansion slots typically for integrated wireless card.
connector (half height)
5 Serial Ports (3 x RJ12 Provides data I/O with any RS–232 peripheral and power.
powered @ 12v, 2 x RJ45
powered @12v or 5v)
Product Overview 1-3

Features Benefits
4 USB 3.0 Ports Provides data I/O with any USB peripheral. Fast data rates with USB.
Note: This product does not support low speed USB devices (1.5Mbit/s).
NCR recommends using Full, High, and SuperSpeed USB devices to avoid a
possible coexistence problem with higher speed peripherals in electrically
noisy environments not following the NCR Workstation and Peripherals AC
Wiring Guide (BSTO-2115-53). None of NCR’s current peripherals are low
speed USB.
1 Powered USB 12 V Port Provides 12V power and data I/O with any USB peripheral and can be used
as a standard USB 2.0 port. Refer to www.poweredusb.org for more
information.
1 Dedicated Cash Drawer Port Provides port for direct drive cash drawers (12 V or 24 V dual cash drawer
(RJ12, 24V) support via Y cable).
1 HDMI Port Provides port for a second digital display. Cable available to DVI.
1 Display Port Provides port for third digital display.
Retail and Hospitality The retail and hospitality hardened design offers a spill resistant, high
Hardened Design impact enclosure that is built to withstand tough in-store conditions with
continuous operation. The fanless configuration increases reliability by
preventing forced air through the unit, thereby reducing contaminants in
the system. The P1535 is configured as a silent, thin-client, fanless, solid-
state terminal for maximum reliability.
Variable Position Tilt-Stand The tilt-stand provides variable tilt positions that are secured without need
with Power Supply for pins or locking knobs.
The dual-friction hinge allows for continuous, smooth rotation throughout
the tilt angle. The stand includes a Cable Door to prevent accidental
disconnect or tampering. It also offers through-counter cable routing,
which hides all cabling from view. With the power supply located in the
base as standard, thermal dissipation of the power supply is isolated and
away from the touch head motherboard electronics, which increases
reliability of the terminal.
The large power supply (150 W) is external to the P-Series stand.
1-4 Product Overview

Optional Features and Benefits

Features Benefits
Customer Display Options include 2x20 VFD (integrated or mounted) or 10” display with
full motion video, POS or extended mounting.
Biometrics Fingerprint Reader Integrated Digital Persona 4500 optical, 512 dpi resolution fingerprint
reader for employee login and security.
Integrated MSR Adds a 3 Track EMSR, Magtek USB 3 Track EMSR, or USB MSR with
NCR key.
2D Imager Integrated Honeywell Imager module. 1D/2D barcode scanner with
ability to read from many media types.
UV Light Sensor Integrated ultra-violet light module and motion sensor for reading
counterfeit currency, ID cards, driver’s licenses, credit cards, and other
UV or hologram items
2-in-1 Dallas/Addimat Sign-In Integrated 2-in-1 waiter key that incorporates the leading waiter keys
Module Dallas and Addimat in one design.
Wireless Adapter Card Wireless network connection card in a PCIe half mini-card form factor.
Wi-Fi certified for 2.4 GHz and 5 GHz band, WPA and WPA2.
Camera Provides an optional built-in, user facing camera.
Mounting Flexibility Provides a compact design that allows wall mounting, P–Series tilt stand
mounting, or X–Series tilt stand mounting
Powered USB Expansion card Adds 1x24v powered USB port and 2 additional powered RJ12 serial
connectors for a total of 7 powered serial ports.
RJ12 Expansion card Adds 1 standard USB port and 2 additional powered RJ12 serial
connectors for a total of 7 powered serial ports.
POE Expansion card Adds 1 x RJ45 power over Ethernet port, 1 x RJ45 serial port (powered 12
v), and 1xSIM card reader. Can be used to power an NCR Basestation4 to
support Orderman devices.
Quickserve Expansion Card Adds 1 x 24V Powered USB port, 1 x 12V powered USB port, and 2 x Cash
Drawer ports via splitter cable from the terminal port.
Product Overview 1-5

Mounting Configurations
1-6 Product Overview

Expansion Options
Product Overview 1-7

Customer Display Options

1-8 Product Overview

Right Side Features (Port A)

Product Overview 1-9

Left Side Features (Port B)

Scanner
Programming the Scanner
To program the scanner to work on a Retail or Hospitality (Aloha) POS, refer to the
following sections in the Imager Setup Sheets document (BCC5-0000-5470):
http://onlinehelp.ncr.com/Retail/Scanners/ImagerSetup/HTML/FrontMatter-HTML/Home.htm
• Retail
• Honeywell N5680 Retail Quick Imager Setup
• Hospitality (Aloha)
• Honeywell N5680 Aloha Programming Sheet
1-10 Product Overview

Specifications
Features Specifications
Processor Intel® Celeron™ Processor N3160 (Quad core, 2.24 GHz)
Chipset Intel® Braswell SoC
Memory 4GB standard up to 8GB DDR3-1600 SDRAM SO-DIMM
Storage Media 40GB upto 120GB 2.5" SSD
Operating System Supports any of the following:
• Windows Embedded POSReady 7 (32 bit)
• Windows Embedded POSReady 7 (64 bit)
• Windows 10 Embedded (32 bit)
• Windows 10 Embedded (64 bit)
• Android
Operator Display 15-inch XGA (1024 x 768), LED LCD, PCap Touch
Network Auto–selecting 10/100/1000 Base - T Ethernet using TCP/IP
Enclosure Polycarbonate/ABS impact resistant, High Strength Blend,
Environmentally Sealed
Camera High Speed USB 2.0, 1920 x 1080 FHD (2.0 M)
Wireless • Dual-Stream, Dual Band 802.11 ac/a/b/g/n 2x2 2.4/5
GHz
• Integrated Bluetooth
Serial Port • (3) RJ12, 12 V
• (2) RJ45, 12 V or 5 V
USB Port • (4) Standard USB 3.0, 5 V
• (1) USB + Powered USB, 12 V
Note: This product does not support low speed USB devices
(1.5Mbit/s). NCR recommends using Full, High, and
SuperSpeed USB devices to avoid a possible coexistence
problem with higher speed peripherals in electrically noisy
environments not following the NCR Workstation and
Peripherals AC Wiring Guide (BSTO-2115-53). None of
NCR’s current peripherals are low speed USB.
Ethernet RJ45 Realtek 10/100/GbE
PCI Express (1) PCI Express Minicard Connector
Product Overview 1-11

Features Specifications
Cash Drawer Port (2) 12 V or 24 V Dual Cash Drawer Support
Note: A Y Cable is required when connecting to any 12 V
cash drawer or to dual cash drawers.
HDMI Port (1) HDMI Port
Display Port (1) Display Port
Expansion A
Serial Port—(2) RJ12, 12V
USB Port — USB 2.0 + Powered Port, 24V
Expansion B
Serial Port—(2) RJ12, 12V
USB Port—USB 2.0, 5V
Expansion Cards
Expansion C
Serial Port—(1) RJ45, 12V RTS and 5V DTR
Power Over Ethernet PSE — RJ45 Exar 10/100Mb
48V Typical Power
IEEE 802.3af
SIM Card Reader — ISO/IEC 7816
2FF SIM Card
Push/Push Connector
Quickserve Expansion
USB Port — (1) USB 2.0 + Powered Port, 24V and (1) USB
2.0 + Powered Port, 12V
Cash Drawer Port — (2) 12V or 24V Cash Drawer ports via
splitter cable from the terminal port.
Power Supply • 19 V, 90 W Power Supply option
• 24 V, 150 W Power Supply option
1-12 Product Overview

Features Specifications
Power Cords • USA Power Cord, 90 W
• USA Power Cord, 150 W
• UK Power Cord, 90 W
• UK Power Cord, 150 W
• Europe Power Cord, 90 W
• Europe Power Cord, 150 W
• Australia Power Cord, 90 W
• Australia Power Cord, 150 W
• China Power Cord, 90 W
• China Power Cord, 150 W
• India Power Cord, 90W
Dimensions (L x W x H) Without MSR and Sidecar
(Countertop envelope 304 mm x 381 mm x 375 mm (12 in. x 15 in. x 14.7 in.)
through tilt angle) With MSR and Sidecar
304 mm x 437 mm x 375 mm (12 in. x 17.2 in. x 14.7 in.)
Base Dimension (L x W) 229 mm x 235 mm (9 in. x 9.25 in.)
(P–Series Stand)
Tilt Angle 3° to 111° from vertical
Terminal Weight 7.39 kg (16.3 lbs)
Note: Varies by configuration. Refer to the NCR P1535 POS
(7761) Site Preparation Guide for more information.
Shipping Weight 6.8 kg (15 lbs)
10.4 kg (23 lbs) – with P-Series Stand
Operating Temperature 0°C – 40°C (32°F – 104°F )
Storage Temperature 0°C – 45°C (32°F – 113°F )
Note: Must be in original packaging material in a humidity
and temperature controlled environment.
Humidity 5% to 85%, non–condensing
Environmental Compliance RoHs, WEEE
EMI Certifications FCC Class A, CE, C-Tick
Safety Certifications TUV, CB Scheme
Product Overview 1-13

Operator Controls
Power Switch
The Power Switch is located as shown below. The switch can be accessed when the cable
cover is opened or closed.

Bezel LED

The Front Panel Bezel LED has multiple functions as defined below.

Color Description
Black System OFF or No power
Blue System ON
Yellow System in Sleep Mode
Green (1 sec.) Successful MSR swipe or Biometric read
Red (1 sec.) Unsuccessful MSR swipe or Biometric read
1-14 Product Overview

Label Locations
Chapter 2: Hardware Installation

Installation Restrictions
• Install the NCR P1535 POS near an electrical outlet that is easily accessible. Use the
power cord as a power disconnect device.
• Do not permit any object to rest on the power cord. Do not locate the NCR P1535
POS where the power cord can be walked on.
• Use a grounding strap or touch a grounded metal object to discharge any static
electricity from your Body before servicing the NCR P1535 POS.
Warning: This unit contains hazardous voltages and should only be serviced by
qualified service personnel.
Caution: Do not connect or disconnect the transaction printer while the terminal is
on. This can result in system or printer damage.

Installation Notes
Cable Restraint
The P1535 includes a cable management system with cable strap to prevent accidental
disconnects and tampering. The strap is opened, peripheral connections are made, the
strap is closed, and then cables are then routed through the slot in the base.

Footprint
An area of no less than 18” inches square is necessary to properly install a P1535 unit
with MSR and side module. This will accommodate the unit as well as its associated
mounting hardware. For customer display attached, see user guide for specific
dimensions.
2-16 Installation Notes and Restrictions

Power
For tilt stand option, the P1535 has an integrated 19 V, 90 W power supply rated for 110
V and 240 V (Auto-sensing), 50 Hz or 60 Hz located in the base. With the powered USB
24 V option, the power supply is a 24V, 150 W external power brick rated for 110 V and
240 V (auto-sensing), 50Hz or 60Hz. Source power is drawn from a regular AC wall
outlet. The electronics are “universal” – that is, they will function when connected to
standard wall outlets in most countries around the world. For use in locales other than
North America, special wall outlet adapters or cables will be required. For international
configurations of the P1535, typically the country specific power cord is ordered
separately.

Moisture
The P1535 units should not be installed in areas where they might be exposed to direct
water spray. P1535 units are not meant for outdoor installation.

Magnetic Strip Reader (MSR) Cleaning

Periodically, the MSR may need to be cleaned depending on usage. Pre-saturated MSR
cleaning cards can be ordered from NCR (50/box) using part number 1666-K024.
Otherwise, wrap a card with a saturated paper towel of glass cleaner and swipe gently
to clean reader head.

Biometric Cleaning
Periodically, the biometric reader may need to be cleaned depending on usage.
For this optical reader, it is recommended to apply the sticky side of a piece of adhesive
cellophane tape to the window, and then peel it away. This works best and avoids
chemicals which may damage the material. An alternative is to use any type of
household cleaner, such as Formula 409, Fantastic, Windex, etc. Use a soft rag, cotton
swab, or something non-abrasive to gently clean the reader surface. Do not use alcohol-
based cleaners. Always spray the cleaner on the rag or swab first to avoid liquid pooling
around the reader. Remove the excess liquid.
Do not to use chlorine based cleaners, such as Clorox bleach, non-chlorine bleach, or
chlorine based bathroom / mildew cleaners. Also, do not use solvents such as acetone,
MEK, TCE, paint thinner, or turpentine. The power should be removed from the
terminal prior to cleaning.

Hardware Platform Drivers

Platform drivers for the P1535 POS are available on http://www5.ncr.com/support/.
Installation Notes and Restrictions 2-17

Ergonomic Workplace
The NCR P1535 POS has a high brightness LCD with an anti-glare screen but for best
results please observe the following when considering the terminal workplace.
• Avoid direct glaring and reflective glaring light. Locate the terminal in a controlled
luminance surrounding. When installed next to windows orient the terminal so it
does not reflect the outside light.
• If possible, avoid reflective glaring caused by electric light sources.
• Position the terminal for ideal viewing angles.
2-18 Installation Notes and Restrictions

Installing the Terminal

The terminal can be mounted using a variety of mounts.
• P-Series Stand (7761-F170)
• X-Series Stand (7761-F172)
• Wall Mount (7761-K001, 7761-K003)
• Space Pole Mount (1668-K104, 7668-K105, 1668-K106)
The NCR P1535 POS comes fully assembled and ready to use. All that is required is to
connect the LAN Cable and peripheral device cables.
Note: For other configurations, refer to the corresponding kit instructions.
1. Pivot the display toward the back.
Installation Notes and Restrictions 2-19

2. Remove the Upper Stand Cover by pivoting it away from the stand. The cover has a
simple snap fit connection at the top.

3. Loosen the thumbscrew to open the Cable Door.

2-20 Installation Notes and Restrictions

4. Loosen the screw on the Terminal Cable Cover. To open, press down on the
indentations in the Cable Cover to unlatch the cover and then pivot the cover open.
Note: Ensure that the screw is disengaged from the threads.

5. Route the cables up through the stand and out of the Terminal Cable Cover.
Installation Notes and Restrictions 2-21

6. Connect the peripheral cables to the I/O Panel.

Note: SIM cards must be inserted while the terminal is powered off.
7. Install the Terminal Cable Cover and tighten thumbscrew to secure cover.
8. Close the Cable Door and tighten thumbscrew to secure cable door.
9. Install the Upper Stand Cover.
2-22 Installation Notes and Restrictions

Connecting AC Power
1. Connect the Power Supply cable to the DC Power connector on the terminal.
2. Connect the AC Power Cord to the Power Supply and to an AC outlet.

Disconnecting the Power Cable

The Power Cable connector locks into position when connected to the terminal and
cannot be removed by simply pulling on the cable. To remove it you must slide the
outside housing out from the terminal to unlock it and then pull it out of the terminal
connector.

Connecting to a Network
Most business configurations require you to connect your P1535 system to a network.
Connecting to a network enables you to communicate with other systems and devices
also on the network, and depending on your business' configuration, may allow you to
connect to the Internet.
To connect the P1535 terminal to a network, plug the 10/100/1000 Ethernet cable into the
port labeled NETWORK on the bottom panel. The other end of the 10/100/1000 Ethernet
cable should be connected into your network hub.
Note: You may need to consult with your business' IT (information technology)
representative to determine whether you have a network connection available, and to
locate the network hub to connect to your P1535.

Starting Up the P1535 Terminal

In order to run your operating system and access your software and data, you must
start up the P1535 platform. To start up the P1535, complete the following procedure:
1. Simply plug the power cord into an electrical outlet. The system automatically turns
on once plugged into the outlet.
The system installs the system devices, system settings, and then reboots to continue
setup. Complete the System Setup. This varies from OS to OS but the following is
typical.
2. The initial setup procedures are performed.
• Starting Windows
• Preparing the computer for the first time
• Checking video performance
3. Accept the License Terms.
Note: Depending on your installed operating system and your selected settings, your
system will vary in the amount of time it takes to boot up.
Installation Notes and Restrictions 2-23

Installing a Transaction Printer

Connect the printer to the USB port on the terminal.
2-24 Installation Notes and Restrictions

Installing a Cash Drawer

The Cash Drawer can be connected to the Cash Drawer connector or to the transaction
printer.
Installation Notes and Restrictions 2-25

Second Cash Drawer Cable Connection

The terminal supports a 2-drawer configuration with a Dual Cash Drawer Cable.
Connect this cable to the terminal or transaction printer cash drawer connector.
There are two versions of the Dual Cash Drawer Cable:
• 1432-C516-0009 (24 V)
• 1432-C517-0009 (12 V)
Note: When connecting a single 12 V legacy cash drawer, the 1432-C517-0009 cable
is required to be used.
Caution: The two cables look very similar. Make sure you use the correct one.
Connecting the wrong cable can cause system damage.
2-26 Installation Notes and Restrictions

Using External Connectors

In order to use the P1535 system to run your business' software, you can set up several
peripheral components. The P1535 is compatible with standard PC equipment,
including a USB mouse, USB keyboard, printer, speakers, network connectivity, as well
as any other devices that can be supported by your operating system.

Note: SIM cards must be inserted while the terminal is powered off.
Installation Notes and Restrictions 2-27

RJ12 Serial Port

The RJ12 serial port is a 6-pin RJ12 connector. Each RJ12 port is capable of supplying 12V
at 500mA max.

Pin Diagram Pin Signal Name

1 POWER/RTS

2 GND

3 TX

4 RX

5 GND

6 CTS

RJ12 Adapter Kits

If a peripheral device requires a different connector to connect to the P1535 POS
terminal serial RJ12 connector, order the following adapter kits:

RJ12 Adapter Kits

1639-K159 DB9M to RJ12 Adaptor (CN100381)
1639-K072 6 ft RJ12 cable (CB10548)
1639-K401 RJ12M to RJ45F Remote Serial Printer Converter Dongle
2-28 Installation Notes and Restrictions

RJ45 Serial Port

The RJ45 port is an 8-pin modular jack connector. Maximum power capability is 0.5A on
the 12V/RTS pin and 0.5A on the 5V/DTR pin from this port. The power output from
this port is protected by a current–limiting power switch.

Pin Diagram Pin Signal Name

1 DSR
2 DCD
3 DTR/5V
4 GND
5 RXD
6 TXD
7 CTS
8 RTS/12V

RJ45 Adapter Kits

If a peripheral device requires a different connector to connect to the P1535 POS
terminal serial RJ45 connector, order the following adapter kits:

RJ45 Adapter Kits

1639–K332 RJ45 to DB25 Adapter Cable 1.85m
1639–K333 RJ45 to DB9 Adapter Cable 1.85m
1639–K400 RJ45 to HSR RJ12 Serial Coverter Dongle
1639–K410 RJ45M to RJ45F Remote Serial Printer Converter Dongle
Installation Notes and Restrictions 2-29

LAN
The 7761 Motherboard provides 10/100/1000 Base T Ethernet support using Realtek
RTL8111F controller. The 7761 Motherboard supports Wake on LAN. The connector
features an integrated magnetic module and 2 LEDs. The LED on the left is yellow and
indicates Link/Activity at 1GBit speed when lit/flashing. The LED on the right is green
and indicates Link/Activity at 10/100Mbit speed when lit/flashing.

Pin Signal Name

1 TD0+
2 TD0-
3 TD1+
4 TD1-
5 TD2+
6 TD2-
7 TD3+
8 TD3-
9 FRAME GND
10 FRAME GND

LAN Cable Kit

LAN Cable Kit

1432–C046–0030 POS; 10/100/1000 CAT 5E Ethernet Cable (ANSI compliantl; 8–wire
2-30 Installation Notes and Restrictions

USB 3.0 Compliant Ports

The 7761 Motherboard provides 4 USB 3.0 compliant ports. Each USB port is capable of
supplying 5V at 900mA max.

Pin Diagram Pin Signal Name

1 VBUS
2 D-
3 D+
4 GND
5 StdA_SSRX-
6 StdA_SSRX+
7 GND_DRAIN
8 StdA_SSTX-
9 StdA_SSTX+
Shell Shield
Installation Notes and Restrictions 2-31

Cash Drawer (CD) Port

A single 6-position RJ12 connector (Molex 44248-0065 or NCR approved equivalent) is
used.

Pin Diagram Pin Signal Name

1 LOGIC GND
2 SOLENOID A
3 OPEN/CLOSE STATUS
4 +24V
5 SOLENOID B
6 POWER GND

Cash Drawer Cable Kits

The terminal supports a 2–drawer configuration with a Dual Cash Drawer Cable.
Connect this cable to the terminal or transaction printer cash drawer connector.
Note: When connecting a single 12 V legacy cash drawer, the 1432–C517–0009 cable is
required to be used.
Caution: The two cables look very similar. Make sure you use the correct one.
Connecting the wrong cable can cause system damage.

Cash Drawer Cable Kits

1432–C516–0009 (24V) 24V Cash Drawer Cable Splitter
1432–C517–0009 (12V) 12V Cash Drawer Cable Splitter
2-32 Installation Notes and Restrictions

Installing the Power Supply

If a power supply is not installed in the base of the P1535 terminal, install a 19 V power
supply.
Caution: The P1535 terminal requires the NCR 19 V or 24 V power supply that is
shipped with the terminal. Use of other power supply may cause damage to the unit. Do
not connect or disconnect the 19 V or 24 V Power Cable from the terminal with the
AC Power Cord still connected to an AC outlet.
To install the 19 V power supply, perform the following procedure:
1. Unpack the terminal in the desired location.
2. Pivot the display toward the back.

3. Remove the Upper Stand Cover by pivoting it away from the stand. The cover has a
simple snap fit connection at the top.
Installation Notes and Restrictions 2-33

4. Loosen the Thumbscrew that secures the Base Cover.

5. Slide the Base Cover toward the front slightly to disengage it from the Base.
2-34 Installation Notes and Restrictions

6. Route the AC Power Cord up through the base of the stand.

7. Attach the Power Cord to the Power Brick.

8. Install the Power Brick in the Base.
Installation Notes and Restrictions 2-35

9. Loosen the thumbscrew to open the Cable Door.

10. Loosen the screw on the Terminal Cable Cover. To open, press the indentations on
the Cable Cover to unlatch the cover then pivot to open.
2-36 Installation Notes and Restrictions

11. Route the power cable up through the stand and connect the power supply cable to
the Power In connector.

12. Secure the excess power cables with a cable tie and place the cables behind the Cable
Door.
13. Close the Cable Door and tighten the thumbscrew to secure the door.

14. Reinstall the Base Cover and tighten thumbscrew to secure cover.
15. Connect the AC Power cord to an AC outlet.
Installation Notes and Restrictions 2-37

Removing Top Assembly

1. Lay the terminal face down on a flat surface.
Caution: Always use a soft material (cloth, foam) to protect the display screen
when placing the terminal face down.
2. Remove the screws (2) that secure the Base Stand to the display.

3. Rotate the P-Series Stand and remove the Mounting Plate Tabs (2) from the openings
in the Rear Cover.
2-38 Installation Notes and Restrictions

Terminal with Expansion

1. Lay the terminal face down on a flat surface.
Caution: Always use a soft material (cloth, foam) to protect the display screen
when placing the terminal face down.

2. Remove the screws (2) that secure the expansion to the display.
Installation Notes and Restrictions 2-39

3. Remove the stand and the Hinge Mount installed over the Expansion Board
assembly.

4. Remove the screws (4) that secure the Expansion Board assembly.
Chapter 3: Cleaning

Cleaning the Touchscreen

Touchscreens can be effectively cleaned with diluted detergent or up to 70% isopropyl
alcohol solution. Follow these steps to avoid damage to the touchscreen:
Warning: Do not use sharp objects to clean around the edges of the touchscreen.
Do not use abrasive cleaners (powders) or abrasive cleaning materials (scrub brush,
scouring pad).
1. Clean the screen using a non-abrasive cloth (microfiber cleaning cloth or cloth
towel) and a diluted detergent solution, such as household soap and water.
Warning: Do not apply any cleaning products directly to the screen. Do not
soak the cloth: wring it out before use.
2. Dry the screen with another soft cloth.
3. Clean the screen further using a cloth dampened with isopropyl alcohol solution, or
using pre-packaged wipes.
Warning: Do not apply any cleaning products directly to the screen. Do not
soak the cloth: wring it out before use.
4. Ensure the glass and screen edges are completely dry before using the unit.
3-41 Cleaning

Cleaning the Cabinet

1. Disconnect the unit from the power outlet before cleaning.
2. Wipe the cabinet using a non-abrasive cloth (microfiber cleaning cloth or cloth
towel) dampened with soap and water solution.
Warning: Do not use alcohol (methyl, ethyl, or isopropyl) or any strong
dissolvent. Do not use thinner or benzene, abrasive cleaners (powders), abrasive
cleaning materials (scrub brush, scouring pad), or compressed air. Do not use
any other types of cleaners such as vinegar, solvents, degreasers, or ammonia-
based cleaners. These can damage the unit.
Warning: Avoid getting liquids inside the unit. If liquid does get inside, have a
qualified service technician check it before you power it on again.
3. Wipe the cabinet using a clean and dry lint-free cloth.
4. Remove external dust around the cooling vents.
Appendix A: Product IDs

P1535 POS (7761)

PID Description
7761-1500-8800 P1535 Res 40GB 8GB RAM WEPR7-32bit MMSR Int2x20 XD10 Wifi
7761-3000-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR
7761-3001-8800 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR
7761-3002-8800 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR
7761-3003-8800 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR
7761-3004-8800 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR
7761-3005-8800 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR
7761-3006-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR Int2x20
7761-3007-8800 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR Int2x20
7761-3008-8800 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR Int2x20
7761-3009-8800 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR Int2x20
7761-3010-8800 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR Int2x20
7761-3011-8800 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR Int2x20
7761-3012-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR BIO
7761-3013-8800 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR BIO
7761-3014-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR Wifi
7761-3015-8800 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR Wifi
7761-3016-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR BIO Wifi
7761-3017-8800 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR BIO Wifi
7761-3018-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR Ext2x20
7761-3019-8800 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR Ext2x20
7761-3020-8800 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR Ext2x20
7761-3021-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR XD10
A-2 Product IDs

PID Description
7761-3022-8800 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR XD10
7761-3023-8800 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR XD10
7761-3024-8800 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR XD10
7761-3025-8800 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR XD10
7761-3026-8800 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR XD10 BIO
7761-3027-8800 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR Int2x20 BIO
7761-3028-8800 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR Int2x20 BIO
7761-3029-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR XB
7761-3030-8800 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR XB
7761-3031-8800 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR XB
7761-3032-8800 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR XB
7761-3033-8800 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR XB
7761-3034-8801 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MBlank Int2x20 EU Cord OM
7761-3035-8801 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MBlank Int2x20 EU Cord OM
7761-3036-8801 P1535 PCAP 60GB 4GB RAM WEPR7-64bit Mblank EU Cord OM
7761-3037-8800 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MBlank
7761-3038-8800 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MBlank Int2x20
7761-3039-8800 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MBlank BIO
7761-3040-8800 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MBlank Int2x20 BIO
7761-3041-8800 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR
7761-3042-8800 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR Int2x20
7761-3043-8800 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR BIO
7761-3044-8800 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR Int2x20 BIO
7761-3045-8800 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR BIO
7761-3046-8801 P1535 PCAP 40GB 4GB RAM WEPR7-64bit 2n1 EU Cord OM
7761-3047-8801 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MBlank EU Cord OM
7761-3048-8801 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR EU Cord OM
7761-3049-8801 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR Int2x20 SC Wifi EU Cord OM
7761-3050-8801 P1535 PCAP 60GB 4GB RAM WEPR7-64bit 2n1 EU Cord OM
Product IDs A-3

PID Description
7761-3051-8801 P1535 PCAP 40GB 4GB RAM WEPR7-64bit 2n1 POE EU Cord OM
7761-3052-8801 P1535 PCAP 60GB 4GB RAM WEPR7-64bit 2n1 POE EU Cord OM
7761-3053-8801 P1535 PCAP 120GB 4GB RAM WEPR7-64bit 2n1 POE EU Cord OM
7761-3054-8801 P1535 PCAP 120GB 8GB RAM WEPR7-64bit 2n1 POE EU Cord OM
7761-3055-8801 P1535 PCAP 120GB 8GB RAM WEPR7-64bit 2n1 EU Cord OM
7761-3056-8801 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MBlank Int2x20 EU Cord OM
7761-3057-8800 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR Int2x20 SC
7761-3058-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR RJ12
7761-3059-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR PUSB UV 150W
7761-3060-8800 P1535 PCAP 40GB 4GB RAM No OS MSR
7761-3061-8800 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR Int2x20
7761-3100-0060 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR
7761-3100-0061 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR
7761-3100-0062 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR
7761-3100-0063 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR
7761-3100-0064 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20
7761-3100-0065 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR Int2x20
7761-3100-0066 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR Int2x20
7761-3100-0067 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR Int2x20
7761-3100-0068 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR BIO
7761-3100-0069 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR BIO
7761-3100-0070 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Wifi
7761-3100-0071 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR Wifi
7761-3100-0072 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR BIO Wifi
7761-3100-0073 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR BIO Wifi
7761-3100-0074 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Ext2x20
7761-3100-0075 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XD10
7761-3100-0076 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR XD10
7761-3100-0077 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR XD10
A-4 Product IDs

PID Description
7761-3100-0078 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XD10 BIO
7761-3100-0079 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20 BIO
7761-3100-0080 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR Int2x20 BIO
7761-3100-0081 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR Int2x20 BIO
7761-3100-0082 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XB
7761-3100-0083 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR XB
7761-3100-0084 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR XB
7761-3100-0085 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR XB
7761-3100-0086 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank
7761-3100-0087 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank Int2x20
7761-3100-0088 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank BIO
7761-3100-0089 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank Int2x20 BIO
7761-3100-0090 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20 SC
7761-3100-0091 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR RJ12
7761-3100-0092 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR UV
7761-3100-0134 P1535 PCAP 60GB 8GB RAM WEPR7-64bit MSR BIO/SC
7761-3100-0135 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR BIO/SC
7761-3100-0136 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR BIO
7761-3100-0137 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR SC
7761-3100-0138 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20 BIO/SC
7761-3100-0140 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XD10 Wifi
7761-3100-0141 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR Int2x20 BIO
7761-3100-0144 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR XT10 BIO
7761-3100-0145 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20
7761-3100-0146 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR XT10
7761-3100-0147 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR XT10
7761-3100-0148 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR XT10
7761-3100-0149 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR XT10
7761-3100-0150 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR XT10
Product IDs A-5

PID Description
7761-3100-0151 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR XT10 BIO
7761-3100-0152 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XT10
7761-3100-0153 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR XT10
7761-3100-0154 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR XT10
7761-3100-0155 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XT10 BIO
7761-3100-0156 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XT10 Wifi
7761-3100-0157 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR XT10 BIO
7761-3100-0158 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR no Cord
7761-3100-0159 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR no Cord
7761-3100-0160 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR no Cord
7761-3100-0161 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR no Cord
7761-3100-0162 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR Int2x20 no Cord
7761-3100-0163 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR BIO no Cord
7761-3100-0164 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR Int2x20 BIO no Cord
7761-3100-0165 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR no Cord
7761-3100-0166 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR no Cord
7761-3100-0167 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR no Cord
7761-3100-0168 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR no Cord
7761-3100-0169 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20 no Cord
7761-3100-0170 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR Int2x20 no Cord
7761-3100-0171 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR Int2x20 no Cord
7761-3100-0172 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR Int2x20 no Cord
7761-3100-0173 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR BIO no Cord
7761-3100-0174 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR BIO no Cord
7761-3100-0175 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Wifi no Cord
7761-3100-0176 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR Wifi no Cord
7761-3100-0177 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR BIO Wifi no Cord
7761-3100-0178 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR BIO Wifi no Cord
7761-3100-0179 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Ext2x20 no Cord
A-6 Product IDs

PID Description
7761-3100-0180 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XD10 no Cord
7761-3100-0181 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR XD10 no Cord
7761-3100-0182 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR XD10 no Cord
7761-3100-0183 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XD10 BIO no Cord
7761-3100-0184 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20 BIO no Cord
7761-3100-0185 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR Int2x20 BIO no Cord
7761-3100-0186 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR Int2x20BIO no Cord
7761-3100-0187 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XB no Cord
7761-3100-0188 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR XB no Cord
7761-3100-0189 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR XB no Cord
7761-3100-0190 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR XB no Cord
7761-3100-0191 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank no Cord
7761-3100-0192 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank Int2x20 no Cord
7761-3100-0193 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank BIO no Cord
7761-3100-0194 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank Int2x20 BIO no Cord
7761-3100-0195 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20 SC no Cord
7761-3100-0196 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR RJ12 no Cord
7761-3100-0197 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR UV no Cord
7761-3100-0198 P1535 PCAP 60GB 8GB RAM WEPR7-64bit MSR BIO/SC no Cord
7761-3100-0199 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR BIO/SC no Cord
7761-3100-0200 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR BIO no Cord
7761-3100-0201 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR SC no Cord
7761-3100-0202 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20 BIO/SC no Cord
7761-3100-0203 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR Int2x20 BIO
7761-3100-0204 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR Int2x20 BIO no Cord
7761-3100-0205 P1535 PCAP 60GB 8GB RAM WEPR7-64bit MSR BIO
7761-3100-0206 P1535 PCAP 60GB 8GB RAM WEPR7-64bit MSR BIO no Cord
7761-3100-0207 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR BIO
7761-3100-0208 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR BIO XB
Product IDs A-7

PID Description
7761-3100-0209 P1535 PCAP 60GB 4GB RAM WEPR7 32-bit no MSR RJ12
7761-3100-0210 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR RJ12
7761-3100-0211 P1535 PCAP 120GB 4GB RAM WEPR7-32bit MSR RJ12
7761-3100-0212 P1535 PCAP 120GB 4GB RAM WEPR7-32bit MSR XR-STAND BIO PUSB 150W
7761-3100-0213 P1535 PCAP 120GB 8GB RAM WEPR7-32bit MSR XD10
7761-3100-0214 P1535 PCAP 40GB 4GB RAM Android MSR
7761-3100-0215 P1535 PCAP 40GB 4GB RAM Android MSR Int2x20
7761-3100-0216 P1535 PCAP 40GB 4GB RAM Android MSR Ext2x20
7761-3100-0217 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MSR BIO XB
7761-3100-0218 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MBlank
7761-3100-0219 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR BIO/SC
7761-3100-0220 P1535 PCAP 60GB 8GB RAM Win10E-64bit MSR QS BIO/SC 150W XR-Stand
7761-3100-0221 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR QS 150W XR-Stand
7761-3100-0222 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR QS 150W
7761-3100-0223 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR QS 150W XR-Stand
7761-3100-0224 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR QS 150W
7761-3100-0225 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank XB
7761-3100-0226 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR RJ12 Int2x20
7761-3100-0227 P1535 PCAP 60GB 8GB RAM WEPR7-64bit MSR Int2x20 BIO
7761-3100-0228 P1535 PCAP 60GB 8GB RAM WEPR7-64bit MSR Int2x20
7761-3100-0229 P1535 PCAP 60GB 8GB RAM WEPR7-64bit MSR Int2x20 BIO XB
7761-3100-0230 P1535 PCAP 60GB 8GB RAM WEPR7-64bit MSR 1KBIO
7761-3100-0231 P1535 PCAP 60GB 8GB RAM Win10E-64bit MBlank QS BIO/SC 150W XR-Stand
7761-3100-0232 P1535 PCAP 60GB 8GB RAM WEPR7-64bit MSR Int2x20 XB
7761-3101-0093 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MBlank Wifi EU Cord OM
7761-3101-0094 P1535 PCAP 60GB 4GB RAM WEPR7-64bit 2n1 Int2x20 EU Cord OM
7761-3101-0095 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR Int2x20 EU Cord OM
7761-3101-0096 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MBlank XB EU Cord OM
7761-3101-0097 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MBlank XB EU Cord OM
A-8 Product IDs

PID Description
7761-3101-0098 P1535 PCAP 60GB 4GB RAM WEPR7-64bit 2n1 XB EU Cord OM
7761-3101-0099 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MBlank XB Int2x20 EU Cord OM
7761-3101-0100 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR XB EU Cord OM
7761-3101-0101 P1535 PCAP 60GB 4GB RAM Win10E-64bit 2n1 EU Cord
7761-3101-0102 P1535 PCAP 60GB 4GB RAM Win10E-64bit 2n1 POE EU Cord
7761-3101-0103 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank EU Cord
7761-3101-0104 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank Int2x20 EU Cord
7761-3101-0105 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR EU Cord
7761-3101-0106 P1535 PCAP 120GB 8GB RAM Win10E-64bit MBlank EU Cord
7761-3101-0107 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR Int2x20 EU Cord
7761-3101-0108 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank POE EU Cord
7761-3101-0109 P1535 PCAP 60GB 4GB RAM Win10E-64bit 2n1 Wifi EU Cord
7761-3101-0110 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank Wifi EU Cord
7761-3101-0111 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank XB EU Cord
7761-3101-0112 P1535 PCAP 60GB 4GB RAM Win10E-64bit 2n1 XB EU Cord
7761-3101-0113 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank Int2x20 XB EU Cord
7761-3101-0114 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XB EU Cord
7761-3101-0115 P1535 PCAP 120GB 8GB RAM Win10E-64bit MBlank XB EU Cord
7761-3101-0116 P1535 PCAP 40GB 4GB RAM No OS 2n1 EU Cord
7761-3101-0117 P1535 PCAP 40GB 4GB RAM No OS 2n1 POE EU Cord
7761-3101-0118 P1535 PCAP 40GB 4GB RAM No OS MBlank EU Cord
7761-3101-0119 P1535 PCAP 40GB 4GB RAM No OS MBlank Int2x20 EU Cord
7761-3101-0120 P1535 PCAP 40GB 4GB RAM No OS MSR EU Cord
7761-3101-0121 P1535 PCAP 40GB 4GB RAM No OS MBlank POE EU Cord
7761-3101-0122 P1535 PCAP 60GB 4GB RAM No OS 2n1 Wifi EU Cord
7761-3101-0123 P1535 PCAP 60GB 4GB RAM No OS MSR EU Cord
7761-3101-0124 P1535 PCAP 60GB 4GB RAM No OS MBlank EU Cord
7761-3101-0125 P1535 PCAP 120GB 4GB RAM No OS MSR Int2x20 SC Wifi EU Cord
7761-3101-0126 P1535 PCAP 120GB 4GB RAM No OS MBlank EU Cord
Product IDs A-9

PID Description
7761-3101-0127 P1535 PCAP 120GB 8GB RAM No OS MBlank EU Cord
7761-3101-0128 P1535 PCAP 40GB 4GB RAM No OS MBlank XB EU Cord
7761-3101-0129 P1535 PCAP 40GB 4GB RAM No OS 2n1 XB EU Cord
7761-3101-0130 P1535 PCAP 40GB 4GB RAM No OS MBlank Int2x20 XB EU Cord
7761-3101-0131 P1535 PCAP 40GB 4GB RAM No OS MSR XB EU Cord
7761-3101-0132 P1535 PCAP 60GB 4GB RAM No OS MBlank XB EU Cord
7761-3101-0133 P1535 PCAP 120GB 8GB RAM No OS MBlank XB EU Cord
7761-3101-0139 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR Int2x20 EU Cord OM
7761-3101-0140 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR Int2x20 Wifi EU Cord OM
7761-3101-0141 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MBlank Int2x20 POE EU Cord OM
7761-3101-0142 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MBlank POE EU Cord OM
7761-3101-0143 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR XD10 BIO
7761-3101-0144 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MBlank EU Cord OM
7761-3101-0145 P1535 PCAP 120GB 8GB RAM WEPR7-64bit MBlank EU Cord OM
7761-3101-0146 P1535 PCAP 120GB 8GB RAM Win10E-64bit 2n1 EU Cord
7761-3101-0147 P1535 PCAP 60GB 4GB RAM No OS MSR XB EU Cord
7761-3101-0148 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MBlank BIO UK Cord OM
7761-3101-0149 P1535 PCAP 60GB 4GB RAM Win10E-64bit 2in1 Int2x20 EU Cord
7761-3101-0150 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank BIO UK Cord
7761-3101-0151 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR EU Cord OM
7761-3101-0152 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR EU Cord
7761-3101-0153 P1535 PCAP 60GB 4GB RAM No OS MBlank BIO EU Cord
7761-3101-0154 P1535 PCAP 60GB 4GB RAM MBlank WEPR7-64bit BIO EU Cord OM
7761-3101-0155 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR EU Cord OM
7761-3101-0157 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank BIO EU Cord
7761-3101-0159 P1535 PCAP 60GB 4GB RAM No OS 2n1 EU Cord
7761-3101-0160 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR CHINA
7761-3101-0161 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR CHINA
7761-3101-0162 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR CHINA
A-10 Product IDs

PID Description
7761-3101-0163 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR 2x20DB CHINA
7761-3101-0164 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR CHINA
7761-3101-0165 P1535 PCAP 60GB 4GB RAM WEPR7-64bit MSR 2x20DB CHINA
7761-3101-0166 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR BIO CHINA
7761-3101-0167 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR 2x20DB CHINA
7761-3101-0168 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR 2x20DB CHINA
7761-3101-0169 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR 2x20DB CHINA
7761-3101-0170 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR 2x20DB CHINA
7761-3101-0171 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR 2x20DB CHINA
7761-3101-0172 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR BIO CHINA
7761-3101-0173 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR 2x20DB BIO CHINA
7761-3101-0174 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR 2x20DB BIO CHINA
7761-3101-0175 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR XD10 CHINA
7761-3101-0176 P1535 PCAP 120GB 4GB RAM WEPR7-64bit MSR XD10 CHINA
7761-3101-0177 P1535 PCAP 40GB 8GB RAM WEPR7-64bit MSR XD10 CHINA
7761-3101-0178 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR XD10 BIO CHINA
7761-3101-0179 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR 2x20DB CHINA
7761-3101-0180 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR BIO CHINA
7761-3101-0181 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR 2x20DB CHINA
7761-3101-0182 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XD10 CHINA
7761-3101-0183 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR XD10 CHINA
7761-3101-0184 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XD10 BIO CHINA
7761-3101-0185 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR 2x20DB BIO CHINA
7761-3101-0186 P1535 PCAP 120GB 4GB RAM Win10E-64bit MSR 2x20DB BIO CHINA
7761-3101-0187 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR 2x20DB SC CHINA
7761-3101-0188 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XB CHINA
7761-3101-0189 P1535 PCAP 120GB 8GB RAM Win10E-64bit MSR XB CHINA
7761-3101-0190 P1535 PCAP 60GB 4GB RAM Win10E-64bit MBlank CHINA
7761-3101-0193 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR Int2x20 UK Cord
Product IDs A-11

PID Description
7761-3101-0194 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR Int2x20 EU Cord
7761-3101-0195 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR XD10 UK Cord
7761-3101-0196 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR XD10 EU Cord
7761-3101-0197 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR XD10 UK Cord
7761-3101-0198 P1535 PCAP 40GB 4GB RAM WEPR7-64bit MSR XD10 EU Cord
7761-3101-0199 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XD10 BIO UK Cord
7761-3101-0200 P1535 PCAP 60GB 4GB RAM Win10E-64bit MSR XD10 BIO EU Cord
7761-3101-0201 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR UK Cord
7761-3101-0202 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR EU Cord
7761-3101-0203 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR Int2x20 UK Cord
7761-3101-0204 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR Int2x20 EU Cord
7761-3101-0205 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR Int2x20 BIO UK Cord
7761-3101-0206 P1535 PCAP 60GB 4GB RAM WEPR7-32bit MSR Int2x20 BIO EU Cord
7761-3500-8800 P1535 PCAP 40GB 4GB RAM WEPR7-32bit MSR Int2x20 Ext2x20 BIO/SC Cam Wifi