OWNERS AND SERVICE MANUAL

INNOVATIVE CONCEPTS IN ENTERTAINMENT INC.

10123 MAIN STREET, CLARENCE, NY 14031
SERVICE: 1-716-759-0360
FAX: 1-716-759-0884
E-MAIL: service@icegame.com
WEBSITE: www.icegame.com
2
 Monsterous - Edition UL certified
Safety Warnings, AC requirements, power ratings 4

SETUP:
Floating the playfield 5
Accessing meters, tickets, and programming buttons.
7
Cabinet Illumination Remote 8
Programming Information 9
SERVICE
Hopper Care 11
Computer Removal 12
Coin Mech care
Marquee Lighting 13
Power supply care
Pusher Deck arm removal 14
Pusher Deck sensor information
Elevator removal 15
Playfield / Monitor Removal 17
SCHEMATICS
H-bridge 18
Serial I/O interface 19
HARNESS 20-37
WARRANTY 38

REV. 01
3
 SAFETY AND WARNINGS BEFORE YOU BEGIN
WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE
USED. FAILURE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAIL-
URE TO USE A GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OP-
ERATION, OR DAMAGE TO THE ELECTRONICS.

NOTE: THIS GAME IS INTENDED FOR INDOOR USE ONLY.

DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE
SAME REASON AS GIVEN ABOVE. USING AN IMPROPERLY GROUNDED GAME COULD
VOID YOUR WARRANTY.
HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A.C. RECEPTACLE TO BE SURE THE
GROUND IS FUNCTIONING PROPERLY.
THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUND-
ING PLANE OF THE GAME. IF THE A.C. GROUND DOES NOT WORK, THE GAME COULD
DISCHARGE STATIC ELECTRICITY THROUGH THE GAME CIRCUITRY, WHICH COULD
CAUSE DAMAGE.
THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE. TO OPERATE THE GAME AT VOLT-
AGES OTHER THAN THOSE IT WAS DESIGNED FOR. PLEASE CONTACT OUR SERVICE
DEPARTMENT FOR VOLTAGE CONVERSION INFORMATION.
WARNING
DO NOT remove any of the components on the main board (e.g. compact flash and eproms)
while the game is powered on. This may cause permanent damage to the parts and the main
board. Removing any main board component part while powered on will void the warranty.

ALWAYS REMOVE POWER TO THE GAME, BEFORE ATTEMPTING ANY SERVICE,

UNLESS NEEDED FOR SPECIFIC TESTING. FAILURE TO OBSERVE THIS PRECAUTION
COULD RESULT IN SERIOUS INJURY TO YOURSELF OR OTHERS.
THIS GAME IS NOT SUITABLE FOR INSTALLATION IN AN AREA WHERE A WATER JET COULD BE
USED.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or in-
struction concerning use of the appliance by a person responsible for their safety. Children should be su-
pervised to ensure that they do not play with the appliance

AC Power Information
The games main fuse is accessed through the back of the game at the power
mod. Above the power cord is a small panel that contains the main fuse. The
value of the fuse for 110 volt users is 5 AMPS at 250Volt type slow blow.

4
SETUP - Floating your playfield.
Your game has been shipped with pre-counted bags of coins. Each bag will be labeled with how
many coins they contain. They should be 250 coins, 900 coins, and 50 coins.
It is important to float your playfield as instructed below.
Step 1:
Open the back door of your game and dump the coins from the 250 bag into the upper hopper.

250 COINS

Step 2:
Unlock the front glass and put aside. Open the bag with 900 coins and take out enough coins to
fill the coins over the edge riser slots.

5
Step 3:
Take the remaining coins and with the machine turned on and the upper pusher deck moving
back and forth, drop handfuls of coins behind the player field scraper shown below in red. As you
drop handfuls of coins behind the player field scraper some will fall over the edge. This is ex-
pected and necessary to properly float the playfield. DO NOT DUMP THE COINS ONTO THE
PLAYFIELD AS IT WILL IMPACT THE PAYOUT PRECENTAGE!!

Final Step:
The remaining bag of coins should be stored in the bottom of the game and used only after the
game has ran for a period of time. It may or may not become necessary to use the remaining bag
of coins. If the lower hopper reports that the level of coins are low, then dump the remaining bag
of 50 into the bottom hopper. You can visually inspect the level of coins in the bottom hopper.
The coins should fill the hopper up to 1” to 1.5” below the top of the hopper as shown below.

1” to 1.5” 1” to 1.5”

6
Setup - Accessing Meters, Ticket Dispensers, and Operator’s Control Panel.
From the top of the control panel, unlock both locks and slide the drawer open. Located on the
left side is the operator’s control panel. On the control panel is the coin meter, ticket meter, toggle
switch and buttons to allow you to change the game’s options. See “Setup - Programming” for
more information.
Located on the right side of the game are two ticket dispensers. You will need to load these with
tickets before operating your game. It is recommend to load each ticket bins with two stacks of
tickets.

Top of game, unlock these.

PROG STEP UP DOWN

COIN TICKET

000000 000000

7
Setup - Remotes
Cabinet lighting

Thirty seconds after power is applied to the cabinet the side illuminate should begin to change to
different colors. If the lights do not power on, press the “D” button to turn them on.

8
Setup - Programming
Your game has been shipped already configured with our suggested settings. To verify or
change any option, open the upper drawer shown on page 9 and toggle the toggle switch. You
should see a screen exactly as shown below. To move the cursor up or down, press the “UP”
and “DOWN” buttons to move the cursor. When the option you wish to change is highlighted,
press the “STEP” button and using the “UP” or “DOWN” buttons you can adjust its value.

To access further options, move the cursor to the last option called “TO ENGINEER MENU” and
press “STEP”. You can now adjust further options. To exit back to the game, toggle the toggle
switch the other way.

9
Setup - Programming (Continued)
Definition of options:

Sound Effects Volume Volume level percentage that game will play game sound effects.
Music Volume Volume level percentage of Music.
Overall Aim% The value of this option is your desired payout.
Coin in Value What is the value of your coin or token.
Cost of Game How much are you charging for one play of the game?
Shot Value This value will determine how many shots you will give your player.
The game will subject from the “cost of game” for each shot.
For example, if cost of game is 20 cents, and you set this to 4 cents,
the player will get 5 shots.
Ticket Value The cost of your ticket or what do you value your ticket at.
Tickets per COE How many tickets you want to give per coin that falls over the edge.
Just for Playing Tickets When enough money is inserted for a credit, the game will pay this
value out to the player before he begins.
Max Bonus Sets a limit to how much a bonus can be, useful when the multiplier
Reset Alarms This will clear all errors reported.
To Engineer Menu This allows you to access the other screen of options.
Attract Volume What volume level percentage the game will output the external amp.
PreLock Monsters This allows you to put monitors in jail already allowing players to reach
the bonus faster.
Monster Hit Multiplier All monster’s coin value will be multiplied by this value.
Max Monster Hit This will set a limit on the highest amount to be paid out per monster.
Splash Damper Delays entrance to the Mega Bonus game.
Update Software Refer to ICE technical support or use a restore disk.
Bucket Capacity Internal setting for ICE technical support use.
Lift Control Internal setting for ICE technical support use.
Reset Menu Options Defaults all values of the game.
Reset Credits/Status Clear credits left in game and current game status.
To Main Menu This allows you to return to the main menu.

10
Hopper Jams and Adjustments
Hopper Jams
Although the game is designed to be as trouble free as possible a
coin jam can occur in any of the hoppers. This can happen if a for-
eign object falls into the hopper itself or a coin has become defec-
tive. The game will alert you to which hopper has the coin jam.
The upper hoppers have a high capacity extension installed that
allows more coins to be present. They also have additional wiring
to detect hoppers that will over flow. Disconnect these wires prior
to removing the hopper bowl. The hopper is a two piece unit. The
bottom assembly is attached to the cabinet while the top called the
bowl is designed to be twisted and removed. It is recommend to
remove as many coins as possible before removing the hopper
bowl. To twist the hopper bowl off you have to press down the re-
lease button shown with the down arrow and then twist the bowl
clockwise. Once the foreign object has been removed check the
spacing of the wheel and the coin out so that only one coin will exit
when the hopper is ran. See below for details. To replace the
bowl, twist counter-clockwise until it “snaps” back in.

Hopper Adjustments
After a hopper jam has occurred the gap between the disc and the lower assembly might have to be
adjusted. Remove the hopper following the “Hopper Removal Instructions” and one coin from one of
the hoppers. Slide the coin as shown below and adjust the gap adjusting screw until the height of the
wheel is within the specs listed below.

Roller Gap
Adjusting Screw

11
Computer Removal.
Remove the bottom door and at the left you will find the computer.
Release the strap holding the computer to the cabinet by pressing on
the sides of the buckle. Disconnect wire connections and pull straight
out.

AC Power AC Power Selector

230 <=> 110

I/O board Video Audio

Accessing coin mech.

Remove the two Allen screws shown and the assembly will slide up and out.

12
Marquee Lighting.

Unlock upper marquee and lift up.

There are 3 curly bulbs.
ICE Part number

E00382

Power Supplies.
Located on the bottom, right of the game are the two power supplies. The left one only supplies
12 volts and its part number is IA2010. The right one is both +24 volts and +12 volts and its part
number is DS2010.

The power supply that is mounted on the left cabinet wall supplies +24 volts to the monitor. The
part number is mon42/47PS.

13
Pusher Deck Arm removal
Open the back door of the game and locate the pusher deck arm. Remove the clips circled.

Pusher Deck Sensor Information

When the back door is removed form the game, power to the pusher is removed. The game will
sound a alarm to inform you that the pusher deck is not working. This is accomplished by a hall
effect sensor (magnetic). As the pusher deck moves back and fourth it will make and break con-
tact with the sensor. The game will watch for this change of state and alarm if not seen.

14
Elevator removal
Open the back door and remove the lower hopper bowl shown below. You will need to remove
the count hopper bowl extension first. To remove, press release button, twist and lift out. Now
remove the lower hopper bowl. See the section “Hopper Jams and Adjustments” for more infor-
mation.
Count Hopper
Lower Hopper

Disconnect the two wire harnesses shown below.

Remove the nut holding the control arm to the elevator. Rotate the arm out of the way.

15
Elevator Removal (CONT)

Slide the elevator assembly to center. The elevator should be lined up with the large hole in the
center of the back panel.

Slightly lift up and back. Now twist the elevator to the right so that the bottom hopper will clear the
bottom shelf. Lift the assembly out.

16
Playfield / Monitor Removal

Step 1
Unlock glass and place aside. Remove left
plastic cover by pulling it straight back.

Step 2
Remove the four mounting bolts
shown.

Step 3
Remove the playfield partially to unplug the playfield wir- ing.
Once the harness is unplugged remove the playfield
completely and put aside.

Step 4
Before you remove the four mounting screws located at the top
and bottom of the monitor, disconnect the DVI/VGA cable and
unscrew the power connections. Now you can remove the
monitor.

17
18
19
BA2063LX
TO:
MT2064LX
BA 8"
1 BROWN (600V) #E00653
2 GREEN/YELLOW (600V) TO:
#E20217
3 BLUE (600V) #E00653
MON26/32PS
3 PIN PLUG #E02206
MALE PIN #E08260

CG2012MT

TO:
MT2083LX 6"
MT
1 black
2 black 59145-010
2 PIN CAP MINI MOLEX #E08537
FEMALE PIN #E08536

CG2012

DS2065LX TO:
IA2010
20"
BROWN #E00653

GREEN/YELLOW #E20217

2" BLUE #E00653

TO:
MT2062MX
TO:
DS BROWN DS2010
20" #E00653
1 BROWN x 2
2 GREEN/YELLOW x 2 GREEN/YELLOW #E20217
3 BLUE x 2
BLUE #E00653
3 PIN PLUG #E02206
MALE PIN #E02422

DS2085LX TO:
MT2050HX

DS
FULL LENGTH @ 20"
Remote 1 ORANGE ORANGE & RED 1
Ground 2 BLACK BLACK 2
Power 3 RED 2 PIN PLUG #E02103
FUSE MALE PINS
PIN 1 #E02422
PIN 2 #E02100S

* HARNESS
PROVIDED WITH 1" 1"
EV2009 AUDIO
AMPLIFIER

20
E00724MTAX

MT2068LX MT2068LX
MT MT
1 orange 5" 5" orange 1
2 red red 2
3 green + + + + + + + + green 3
4 light blue B B B B B B B B light blue 4
R R R R R R R R
4 PIN MINI MOLEX PLUG #E08534 G G G G G G G G 4 PIN MINI MOLEX PLUG #E08534
MALE PIN #E08535 MALE PIN #E08535
#E00724 RGB LED TAPE STRIP
5/8" SPACING

STRIP IS 27 CUTS LONG

E00724MTBX
TO:
E00724MTAX
MT2069LX MT2069LX

MT MT
1 orange 5" 5" orange 1
2 red red 2
3 green + + + + + + + + green 3
4 light blue B B B B B B B B light blue 4
R R R R R R R R
4 PIN MINI MOLEX CAP #E00437 G G G G G G G G 4 PIN MINI MOLEX CAP #E00437
FEMALE PIN #E08536 FEMALE PIN #E08536
#E00724 RGB LED TAPE STRIP
5/8" SPACING

STRIP IS 21 CUTS LONG

E00724MTX
TO:
E00724MTBX
MT2068LX

MT
1 orange 5"
2 red
3 green + + + + + + + +
4 light blue B B B B B B B B
R R R R R R R R
4 PIN MINI MOLEX PLUG #E08534 G G G G G G G G
MALE PIN #E08535
#E00724 RGB LED TAPE STRIP
5/8" SPACING

STRIP IS 27 CUTS LONG

E02390X

SOLDER WIRES TO
LEADS ON SWITCH
ON

black 2 ½”
.187 #E02909 M
NO
COMM
SHRINK
TUBE
black 2 ½”
.187 #E02909 M ON
TOGGLE SWITCH
#E02390

21
MS2364X
#HD2364 – 110V AC FAN

TO:
MT2063MX
12" MS
brown 1
GREEN/YELLOW 2
brown 3

3 PIN PLUG #E02206

SOLID PIN #E02100S
13" PIN 2 #E08260

GREEN/YELLOW
#E20217

MT1033X
MT
5"
1 gray
2 gray/black
3 black x 2
3 PIN PLUG MINI MOLEX #E08539
MINI MALE PIN #E08535

COM. N.O. N.C. COM. N.O. N.C.

SWITCH #8422 SWITCH #8422

MT1055X
MT
1 gray/black
2 black 3" 1"

2 PIN PLUG MINI MOLEX #E08533

MINI MALE PIN #E08535

COM. N.O. N.C. COM. N.O. N.C.

SWITCH #8422 SWITCH #8422

MT2008X

TO:
MT2050HX
MT2084HX
2" black M .187 #E02909
black M .187 #E02909

MT2008 MOTOR 22
MT2050HX (1 of 6)

MOTOR 1+2
1 black/yellow
2 gray/red
3 orange/yellow PAGE 2
4 gray/brown
5
6
7
8
9 orange 24"
10 black

10 PIN CST-100 #E02851 TO:

CST PIN #E00383
MT2060MX
PWR 12 MT
1 ORANGE 24" black 1
3 1 2 BLACK 2
3 BLACK 3
4 2
4 BLACK BLACK 4
BLACK/WHITE 5
4 PIN MOLEX HOUSING #E00274
MOLEX SOCKET #E02065 BLACK/WHITE x 2 6
orange 7
PWR 12 ORANGE 8
1 ORANGE 29" ORANGE 9
3 1 2 ORANGE 10
3 BLACK ORANGE 11
4 2
4 BLACK 12
13
4 PIN MOLEX HOUSING #E00274
MOLEX SOCKET #E02065 LIGHT BLUE 14
LIGHT BLUE 15
LIFT 15 PIN PLUG #E02144
SPLIT PIN #E02100
1 gray/orange PIN 6 #E02422
2 gray/yellow
6 1 3 gray/green TO:
4 black/gray DS2085LX
7 2
5 8" ORANGE 1
8 3
6 gray/blue BLACK/WHITE 2
9 4 7 ORANGE 18"
2 PIN CAP #E02181
10 5 8 ORANGE/BLACK FEMALE PIN #E02102
9 BLACK
10 BLACK/WHITE 26 ½”
10 PIN MOLEX HOUSING #E00275
MOLEX SOCKET #E02065
TO:
PPSU N.O. E08973
1 LIGHT BLUE 27" 32" ORANGE .187 #E00651
2 18" ORANGE .187 #E00651
4 1
3 BLACK/WHITE
5 2
4 COM
6 3 5
6
6 PIN MOLEX HOUSING #E02097
MOLEX SOCKET #E02065

PWR 24
1
2 1 2 LIGHT BLUE 29"
2 PIN MOLEX HOUSING #E00392
MOLEX SOCKET #E02065

23
MT2050HX (2 of 6)
TO:
TO:
MT2035X
YELLOW PAINTED MT2087HX
ZIP TIE
PINS MT
1 violet/brown 36" violet/brown 1
2 violet/red violet/red 2
3 violet/orange violet/orange 3
4 violet/yellow violet/yellow 4
5 violet/green violet/green 5
6 violet/blue violet/blue 6
7 violet violet 7
8 violet/gray violet/gray 8
9 violet/black violet/black 9
10 violet/white violet/white 10
11 orange/white orange/white 11
12 12
12 PIN CST-100 #E02094 12 PIN CAP #E02105
CST PIN #E00383 FEMALE PIN #E02102

To:
EV2009 Audio MT 4"
Amplifier 1 red/white 72" red/white
2 brown/white
3 brown/gray brown/white
4 red/gray
49" red/gray .187 #E00651
To:
4 PIN AMP HOUSING #E02429 brown/gray
CONTACT PIN #E02201
.187 #E00651 2007 4" SPEAKERS

4"

TO:
TO:
RR8520X
MT2060MX
MT
8"
1 orange 59 ½” orange x 2 1
2 black black x 2 2
2 PIN PLUG #E02103 2 PIN CAP #E02181
SOLID PIN #E02100S FEMALE PIN #E02102

58 ½” TO:
RR8520X

orange 1
black 2
2 PIN CAP #E02181
FEMALE PIN #E02102

24
MT2050HX (3 of 6)

LIFT
1 gray/orange 26"
2 gray/yellow
6 1 3 gray/green
4 black/gray
7 2
5
8 3
6 gray/blue TO:
9 4 7 ORANGE MT2084HX
PAGE 1
8 ORANGE/BLACK MT
10 5
9 BLACK BLACK 1
10 BLACK/WHITE PAGE 1 gray/green 2
10 PIN MOLEX HOUSING #E00275 gray/blue 3
MOLEX SOCKET #E02065 black/gray 4 1 12
yellow 5
2 13
HOP-CD yellow/red 6
1 yellow/brown 23" yellow/brown 7 3 14

2 yellow/red black 8 4 15
3 yellow red/black 9 5 16
8 1 4 black orange/black 10
6 17
9 2 5 red/black blue/black 11
6 orange/black ORANGE/BLACK 12 7 18
10 3
7 blue/black gray/yellow 13 8 19
11 4 8 gray/orange 14 9 20
12 5 9 yellow/violet 15
10 21
13 6
10 yellow/blue 16
11 yellow/green 17 11 22
14 7
12 yellow/orange 18
13 black/white 19
14 red/white 20
orange/white 21
14 PIN MOLEX HOUSING #E00279
MOLEX SOCKET #E02065 blue/white 22

22 PIN MOLEX PLUG #E00747

MALE MOLEX PIN #E00620

HOP-AB
1 yellow/orange 23"
2 yellow/green
3 yellow/blue
9 1
4 yellow/violet
5 black/white
10 2
6 red/white
11 3 7 orange/white
12 4 8 blue/white
13 5
9
10
14 6
11
15 7 12
16 8 13
14
15
16
16 PIN MOLEX HOUSING #E02096
MOLEX SOCKET #E02065

25
MT2050HX (4 of 6)

TO:
MT1055RX
66" gray/brown 1
orange/yellow x 2 2
2 PIN CAP MINI MOLEX #E08537
FEMALE PIN #E08536

11"
TO:
5"
MT2008X
orange/yellow .187 #E00651

black/yellow .187 #E00651

36 ½"

TO:
MOTOR 1+2 MT1055LX
1 black/yellow 40 ½"
2 gray/red 40 ½" 40 ½" gray/red 1
3 orange/yellow 66" black/yellow x 2 2
4 gray/brown 66" 2 PIN CAP MINI MOLEX #E08537
5 FEMALE PIN #E08536
6
7
8
9 orange
10 black PAGE 1

10 PIN CST-100 #E02851 TO:

CST PIN #E00383
MT2081LX

44" light blue 1

black x 2 2
orange 3
HOP-EF yellow/gray 4
1 yellow/gray red 5
2 yellow/white yellow/white 6
3 yellow/black 7
7 1 4 black 6" black 8
8 2 5 red yellow/black 9
6 orange
9 3 9 PIN CAP MOLEX #E02974
7 violet/white FEMALE MOLEX PIN #E02176
10 4 8 violet/blue
11 5 9 gray/violet
PAGE 5 PARTS PEOPLE
12 6
10 black/white
11 orange/white TO ADD 6"
12 light blue
JUMPER
12 PIN MOLEX HOUSING #E02024
MOLEX SOCKET #E02065

26
MT2050HX (5 of 6)

HOP-EF
1 yellow/gray
2 yellow/white
3 yellow/black
7 1 4 black TO:
PAGE 4
8 2 5 red BLUE PAINTED MT2051HX
6 orange ZIP TIE
9 3
7 violet/white 36" violet/white 1
10 4 8 violet/blue violet/blue 2
11 5 9 gray/violet gray/violet 3
12 6
10 black/white black/white 4
11 orange/white orange/white 5
12 light blue blue/white 6 DECAL (x2)
blue/black 7 BLUE #7017
12 PIN MOLEX HOUSING #E02024
MOLEX SOCKET #E02065 black 8
orange/black 9
black/red 10
HOP-G black/orange 11
1 blue/white 43 ½” orange 12
4 1
2 blue/black GREEN/YELLOW 13
3 gray/blue gray/blue 14
5 2
4 black 15
6 3 5 15 PIN CAP #E02367
6 orange/black FEMALE PIN #E02102
PIN 13 #E08259
6 PIN MOLEX HOUSING #E02097
MOLEX SOCKET #E02065

METERS
1 black/red 43 ½"
2 black/orange
3
4 orange
4 PIN CST-100 #E02722
CST PIN #E00383

GREEN/YELLOW 83 ½” TO:
#E20217
(600V) MT2051HX
COIN
MECH 40" black/tan 1
1 black/tan white/brown 2
1 2 2 orange white/red 3
3 white/orange 4
3 4 4 white/yellow 5
5 white/green 6
5 6 6 tan black 7
7 white/blue 8
7 8 white/violet
8 white/brown 9
9 white/gray 10
9 10
10 white/black 11
#E00458 - CONN 10P .100 DUAL ROW white 12
#E08541 - CONTACT AMP .100 black 13
orange 14
KEYS tan 15
1 white/red 44"
15 PIN CAP #E02367
2 white/orange FEMALE PIN #E02102
3 white/yellow
4 white/green
5
6 black

6 PIN CST-100 #E08634

CST PIN #E00383

JOY
1 white/blue 45"
2 white/violet
3 white/gray
4 white/black
5 white
6
7 black

7 PIN METHODE #E02091

27
MT2050HX (6 of 6)

MT
TO:
ALARM 16" 4" TILT #CP1051
1 black 52" black #E20217
2 black
3 black pink #E20217
4 pink
5 brown/green
6
7 brown/blue TO:
8 #CG2012MTX
9
10 18" black 1
11 brown/green 2
12 2 PIN PLUG MINI MOLEX #E08533
12 PIN CST-100 #E02094 MALE PIN #E08535
CST PIN #E00383

TO:
SLAM SWITCH
#CR1050
2"
46" black x 2 .187 #E00651

brown/blue x 2 .187 #E00651

TO:
SLAM SWITCH
#CR1050
2"
39" black .187 #E00651

brown/blue .187 #E00651

MT2051HX (1 of 2)
1
TO:
MT2050HX BLUE PAINTED 72" violet/blue 1 T Sense
ZIP TIE black/white x 2 2 P GND
1 violet/white violet/white 3 T Run
2 violet/blue orange/white 4 + 12VDC
3 gray/violet 76" 4 PIN MLX CAP #E02158
4 black/white FEMALE PIN #E02176
5 orange/white 2
6 blue/white
DECAL (x2) 7 blue/black 72" blue/black 1 T Sense
BLUE #7017 8 black black 2 P GND
9 orange/black blue/white 3 T Run
10 black/red orange/black 4 + 12VDC
11 black/orange 4 PIN MLX CAP #E02158
12 orange FEMALE PIN #E02176
13 GREEN/YELLOW
14 gray/blue 79" 20"
15 KEY #E02549
15 PIN PLUG #E02144
SPLIT PIN #E02100
PIN 13 #E08260 black/white x 2 .187 #E00651 COM
gray/violet .187 #E00651 N.C.
20"
black/white .187 #E00651 COM
gray/blue .187 #E00651 N.C.

C
#E02558
33" black/red 9" black 0000000000 #PC20224
red 12v COUNTER
COIN
orange
#E02815 9"
33"
9"
T
red 0000000000 #PC20224
#E02558
33" black/orange 9" black
TICKET 12v COUNTER

NO DECALS ON
COUNTERS

42" GREEN/YELLOW #E20217

(600V) 28
MT2051HX (2 of 2)
TO:
MT2050HX
MT 2"
1 black/tan 56" black/tan .250 FLAG
2 white/brown #E00648
3 white/red 56" white/brown .250 FLAG
4 white/orange #E00648
5 white/yellow
6 white/green 56" orange .187 #E00651
7 black 56" tan .187 #E00651
8 white/blue
9 white/violet
10 white/gray
11 white/black 2"
12 white 42" white/red .187 #E00651
13 black black DOWN
.187 #E00651
14 orange
6"
15 tan 42" white/orange .187 #E00651
15 PIN PLUG #E02144 black x 2 UP
.187 #E00651
SPLIT PIN #E02100
6"
42" white/yellow .187 #E00651
black x 2 TEST
.187 #E00651

42" 6" white/green .187 #E00651

42" black x 2 DIAG
.187 #E00651

61 ½" white .250 FLAG

#E00648
black .250 FLAG
#E00648
6"
D
63" white/black .250 FLAG
#E00648
black x 2 .250 FLAG
#E00648
10"
L
63" white/blue .250 FLAG
#E00648
black x 2 .250 FLAG
#E00648
6"
U
60 ½" white/gray .250 FLAG
#E00648
black x 2 .250 FLAG
#E00648

6"
R
60" white/violet .250 FLAG
#E00648
black x 2 .250 FLAG
#E00648

MT2061LX
TO:
SX007X 5A
POWER MOD ASY DECAL #7902 (x2)
DECAL #7090 (x1)
MT
2 6"
1 BROWN
2
3 BLUE
3 PIN PLUG #E02206 7
MALE PIN #E08260
DECAL #7140 (x1)

3"
DECALS
*CONNECT WIRES TO # SCREW TERMINALS ON 2004 – OCTAL SOCKET

29
MT2060MX
TO:
TO: MT2067LX
PE2063LX
1 ORANGE 10" ORANGE x 2 1
2 BLACK BLACK x 2 2
2 PIN CAP #E02181 2 PIN CAP #E02181
FEMALE PIN #E02102 FEMALE PIN #E02013

14"

TO:
IA2010 TO:
9" MT MT2050HX
4"
#E00046 BLACK x 3 14" BLACK 1
BLACK 2
#E00046 BLACK x 3 BLACK 3
BLACK 4
#E00046 ORANGE x 3 BLACK/WHITE 5
BLACK/WHITE 6 13 10 7 4 1
#E00046 ORANGE x 3 ORANGE 7
ORANGE 8
ORANGE 14 11 8 5 2
9
25" ORANGE 10
TO: ORANGE 11 15 12 9 6 3
DS2010 12
#E00046 BLACK/WHITE x 2, BLACK 14" 13
LIGHT BLUE 14
LIGHT BLUE x 2 LIGHT BLUE 15
#E02700
15 PIN CAP #E02367
FEMALE PIN #E02102

MT2062MX
WRAP DECALS 3" FROM ENDS
DECAL #7089 (x1) DECAL #7091 (x1)

TO: 1 BROWN BROWN

3
SX007X 5A TO:
POWER MOD ASY 6" 6" DS2065X
MT
1 BROWN BROWN x 2 1
2 G/Y 12" G/Y x 2 2
3 BLUE BLUE x 2 3
3 PIN PLUG #E02206 3 PIN CAP #E02288
MALE PIN #E08260 FEMALE #E02013

6" TO:
MT2064LX
*CONNECT WIRES TO # SCREW TERMINALS ON 2004 – OCTAL SOCKET
BROWN x 2 1 YELLOW DECAL
G/Y x 2 2 PC /
“PC / MONITOR” (x2)
BLUE x 2 3 MONITOR
#7141
3 PIN CAP #E02288
FEMALE #E02013

6"
TO:
MT2065LX

BROWN 1
G/Y 2 TABLE WHITE DECAL
BLUE 3 MOTOR “TABLE MOTOR” (x2)
#7142
3 PIN CAP #E02288
FEMALE #E08259

PE2063LX
MT TO:
MT2060MX 8"
red
1
black
2
2 PIN PLUG #E02103 TO:
SOLID PIN #E02100S
E00753 RGB LED
CONTROLLER

30
MT2063MX
TO:
DECAL #7902 (x2)
MS2364X
MT
1 BROWN 2" STRIP 70" 5" STRIP BROWN x 2 1
2 GREEN/YELLOW GREEN/YELLOW x 2 2
3 BLUE
3 COND 18 AWG E02855 BLUE x 2 3
3 PIN PLUG #E02206 3 PIN CAP #E02288
MALE PIN #E08260 FEMALE #E02013

TO:
SX007X 5A

E02855
POWER MOD ASY 30"

TO:
SH2130X
BROWN x 2 1
GREEN/YELLOW x 2 2
BLUE x 2 3
3 PIN CAP #E02288
FEMALE #E02013

8"
TO:
SH2130X
BROWN x 2 1
GREEN/YELLOW x 2 2
BLUE x 2 3
3 PIN CAP #E02288
FEMALE #E02013

8"
TO:
SH2130X
BROWN x 2 1
GREEN/YELLOW x 2 2
BLUE x 2 3
3 PIN CAP #E02288
FEMALE #E02013

8"
TO:
SH2130X
BROWN 1
GREEN/YELLOW 2
BLUE 3
3 PIN CAP #E02288
FEMALE #E08259

MT2064LX
To: 16"
TO:
MT2062MX
DS2000X
MT
1 BROWN & BLACK 16"
PC / GREEN/YELLOW & GREEN
N L
2
MONITOR 3 BLUE & WHITE E
3 PIN PLUG #E02206
YELLOW DECAL MALE PIN #E02422 POWER CORD FROM COMPUTER
“PC / MONITOR” (x2) #DS2000
#7141 TO:
BA2063LX
MONITOR

18" BROWN 1
GREEN/YELLOW 2
BLUE 3
3 PIN CAP #E02288
FEMALE #E08259
YELLOW DECAL
“MONITOR” (x2) #7098

31
MT2065LX
TO:
CHERRY SWITCH
#E08973

.187 #E00651

.187 #E00651
“N.O.” N.O. COM “C”

TO:
MOTOR
To: 6" #MT1194X
MT2062MX
MT
1 BROWN 2" STRIP 50" 3" STRIP BROWN BROWN .250
TABLE #E00653T
2 GREEN/YELLOW
MOTOR
3 BLUE
3 COND 18 AWG E02855 BLUE .250
#E00653T
3 PIN PLUG #E02206
SOLID PIN #E08260 2"

WHITE DECAL
“TABLE MOTOR” (x2) G/Y #E20217
#7142

MT2066LX
TO:
MONITOR TO:
MONITOR POWER
SUPPLY
MT
4"
1 BLACK 48" BLACK x 2 #E02700
2 BLACK
3 RED RED x 2 #E02700
4 RED
4 PIN AMP HOUSING #E02429
CONTACT PIN #E02201

MT2068LX
MT
2"
5"
orange 1
red 2
green 3
light blue 4
4 PIN MINI MOLEX PLUG #E08534
MALE PIN #E08535

MT2069LX
MT
2"
5"
orange 1
red 2
green 3
light blue 4
4 PIN MINI MOLEX CAP #E00437
FEMALE PIN #E08536

MT2070LX TO:
RGB LED
CONTROLLER
#E00753
MT
3" 2"
24"
orange 1
red 2
green 3
light blue 4
4 PIN MINI MOLEX CAP #E00437
FEMALE PIN #E08536

32
MT2071LX
GREEN/YELLOW 72" GREEN/YELLOW x 2 #E08263 -
#E20217
#10 YELLOW

34"

GREEN/YELLOW #E20217

MT2080LX
MT
TO:
EXP MT2034X TO: EXP-IN
1 MT2035X 1
2 violet/brown 8" violet/brown 2
3 violet/red violet/red 3
4 violet/orange violet/orange 4
5 violet/yellow violet/yellow 5
6 violet/green violet/green 6
7 violet/blue violet/blue 7
8 violet violet 8
8 PIN CST-100 #E02092 8 PIN CST-100 #E02092
CST PIN #E00383 CST PIN #E00383

MT2081LX

TO:
#MT2050HX (1)
To:
#DS5002B – SH400 COIN HOPPER #MT2084HX (2)
WARNING DECAL
4" PLACE DECAL
#7123
3" BACK MT
+24VDC 1 red (24 AWG) 16" red 1
Gnd 2 black (24 AWG) black+black/white 2
+12VDC 3 orange (24 AWG) WARNING orange 3
control 4 green (24 AWG) green 4
5 TURN OFF red/white 5
+5VDC 6 red/white (24 AWG) MACHINE BEFORE white 6
count 7 white (24 AWG) CONNECTING white/yellow 7
Gnd 8 black/white (24 AWG) black 8
yellow/black 9
9 PIN PLUG MOLEX #E02973
MALE PIN #E02159

.187 #E00651 white/yellow 16"

.187 #E00651
black

.250 yellow/black 18"

#E00653T

33
MT2084LX
TO: TO:
MT2008X MT1033DX

ORANGE/BLACK 16" gray/blue 1

.187 #E00651
.187 #E00651 BLACK gray/green 2
black/gray 3
3 PIN CAP MINI MOLEX #E08538
FEMALE PIN #E08536

30"

TO:
MT2081LX

20" blue/black 1
black x 2 2
orange/black 3
yellow/brown 4
TO: red/black 5
MT2050HX yellow/red 6
6"
yellow 7
MT 6" black 8
1 BLACK 9
2 gray/green
3 gray/blue 9 PIN CAP MOLEX #E02974
4 black/gray x 2 FEMALE PIN #E02176
12 1
5 yellow
13 2
6 yellow/red
14 3
7 yellow/brown
15 4 8 black
16 5
9 red/black
17 6
10 orange/black PARTS PEOPLE
11 blue/black
18 7 12 ORANGE/BLACK
TO ADD 6"
19 8 13 gray/yellow JUMPER
20 9
14 gray/orange
15 yellow/violet
21 10
16 yellow/blue
22 11 17 yellow/green
18 yellow/orange
19 black/white TO:
20 red/white MT2081LX
21 orange/white
22 blue/white 34" blue/white 1
22 PIN MOLEX HOUSING #E00281 black/white x 2 2
MOLEX SOCKET #E02065 orange/white 3
yellow/orange 4
red/white 5
yellow/green 6
yellow/blue 7
6" black/white 8
yellow/violet 9

9 PIN CAP MOLEX #E02974

FEMALE PIN #E02176

TO:
MT1033UX

36" gray/yellow 1
gray/orange 2
black/gray 3
3 PIN CAP MINI MOLEX #E08538
FEMALE PIN #E08536

34
MT2087LX orange/white PARALLEL
#E02513SPLICE
TO:
MT2086LX
MT 7"
1
2
3 orange/white x 2 PARALLEL
4 #E02513SPLICE
5
6
7 7"
8
9
10
11 orange/white 12" orange/white x 2 PARALLEL
12 #E02513SPLICE
12 PIN PLUG #E02106
SPLIT PIN #E02100

MT2088LX
violet 4"
E02100
SPLIT PIN

MT2089LX MT
5"
1 gray
TO: 2 gray/black
MT2084HX 3 black x 2
3 PIN PLUG MINI MOLEX #E08539
MINI MALE PIN #E08535

MT 3"
MT2090LX TO: 1 gray/black
MT2050HX 2 black

2 PIN PLUG MINI MOLEX #E08533

MINI MALE PIN #E08535

PE2009X

#E00638 .187
.187 #E00651

PINK x 2 WHITE

6" BLACK
M
.250
6" #E00654
6"
6" PINK
M
.250
#E00654

35
RR8520X

#RR1026-P802 - BRACKET
LAMP

#8520 - HALOGEN BULB

SOCKET TO:
MT2067LX

WHITE
1
WHITE
2
2 PIN PLUG #E02103
SOLID PIN #E02100S

SX2007X DECAL #7085

5 AMP
#SX2007X-POWER MODULE ASY 250V

DECAL #7077
#E02258 – FUSE 5 AMP 250V (MDL - 5)
#2892-POWER MODULE
CORCOM ( PELSOSSXO) TIME DELAY FUSE
BLUE
.187 #E00651
A B C D

.187 #E00651 #SX2055X-POWER MODULE HARNESS

5 AMP FUSE DECAL #7902 (x2)

#E20217 BROWN 10 " BROWN x 2 1

GREEN/YELLOW x 2 2
BLUE x 2 3
GREEN/YELLOW x 2 3 PIN CAP #E02288
#E00638 FEMALE #E02013
.187
TO:
MT2061LX
15 "

3 "
GREEN/YELLOW
BROWN x 2 1
GREEN/YELLOW x 2 2
BLUE x 2 3
3 PIN CAP #E02288
FEMALE #E02013

6 " TO:
MT2062MX

SX
BROWN 1
GREEN/YELLOW 2
BLUE 3
3 PIN CAP #E02288
FEMALE #E08259

TO:
MT2063LX

36
SX2055X

TO:
DECAL #7902 (x2) MT2061LX

BROWN 10 " BROWN x 2 1

.187 #E00651
.187 #E00638 GREEN/YELLOW x 2 GREEN/YELLOW x 2 2
.187 #E00651 BLUE BLUE x 2 3
3 PIN CAP #E02288
FEMALE #E02013

3 "

15 "
TO:
GREEN/YELLOW MT2062MX
#E20217

BROWN x 2 1
GREEN/YELLOW x 2 2
BLUE x 2 3
3 PIN CAP #E02288
FEMALE #E02013

6 "
TO:
MT2063LX
SX
BROWN 1
GREEN/YELLOW 2
BLUE 3
3 PIN CAP #E02288
FEMALE #E08259

SX2130X
LEAVE AT FULL LENGTH
APPROX 9"

SH 2"
1 BLACK
2 GREEN/YELLOW (600V)
3 WHITE
3 PIN PLUG #2206 CERAMIC BULB SOCKET
MALE PIN (20-14 AWG) #8260
#2130
TO:
10 "
MT2063MX

(600V) GREEN/YELLOW
#E20217

37
 WARRANTY POLICY
I.C.E. Inc warrants all components in new machines to be free of defects in materials and workmanship for
the period listed below:

■ 180 days on Main PCB’s, Computers & Motors

■ 1 year on all LCD monitor panels
■ 90 days on all other electronic and mechanical components
■ 30 days on all I.C.E. repairs and parts purchases

I.C.E. Inc shall not be obligated to furnish a warranty request under the following conditions:

■ Equipment or parts have failed through normal wear and tear

■ Equipment has been subjected to unwarranted stress, abuse or neglect
■ Equipment has been damaged as a result of arbitrary repair/modification

Products will only be covered under warranty by obtaining an I.C.E. authorized RMA #. To obtain an RMA #
please provide I.C.E. tech support with the game serial # or original I.C.E. invoice # and a detailed descrip-
tion of the failure or fault symptoms.

I.C.E. Inc will assume no liability whatsoever for costs associated with labor or travel time to replace defec-
tive parts. All defective warranty covered components will be replaced with new or factory refurbished com-
ponents equal to OEM specifications.

I.C.E. Inc will cover domestic UPS ground, or comparable shipping costs during the warranty period. Inter-
national or expedited shipments are available for an additional charge. To obtain credit defective parts
must be returned to I.C.E. Inc, at the customer’s expense, within 30 days. After 30 days a 15% re-stocking
fee will apply to all returns.

ICE distributors are independent, privately owned and operated. In their judgment, they may sell parts and/
or accessories other than those manufactured by I.C.E. Inc. We cannot be responsible for the quality, suit-
ability or safety of any non-I.C.E. part or modification (including labor) that is performed by such a distribu-
tor.

Innovative Concepts in Entertainment

10123 Main St.
Clarence, NY 14031
Phone #: (716) - 759 – 0360
Fax #: (716) – 759 – 0884
www.icegame.com

38