600W Single Output with PFC Function HRP-600 series

Features :
Universal AC input / Full range
Built-in active PFC function, PF>0.94
High efficiency up to 89%
Withstand 300VAC surge input for 5 seconds
Protections: Short circuit / Overload / Over voltage / Over temperature
Built-in constant current limiting circuit
Built-in cooling fan ON-OFF control
Built-in DC OK signal
Built-in remote sense function
All using 105 long life electrolytic capacitors
5 years warranty

SPECIFICATION
MODEL HRP-600-3.3 HRP-600-5 HRP-600-7.5 HRP-600-12 HRP-600-15 HRP-600-24 HRP-600-36 HRP-600-48
DC VOLTAGE 3.3V 5V 7.5V 12V 15V 24V 36V 48V
RATED CURRENT 120A 120A 80A 53A 43A 27A 17.5A 13A
CURRENT RANGE 0 ~ 120A 0 ~ 120A 0 ~ 80A 0 ~ 53A 0 ~ 43A 0 ~ 27A 0 ~ 17.5A 0 ~ 13A
RATED POWER 396W 600W 600W 636W 645W 648W 630W 624W
RIPPLE & NOISE (max.) Note.2 100mVp-p 100mVp-p 100mVp-p 120mVp-p 150mVp-p 150mVp-p 200mVp-p 240mVp-p
OUTPUT VOLTAGE ADJ. RANGE 2.8 ~ 3.8V 4.3 ~ 5.8V 6.8 ~ 9V 10.2 ~ 13.8V 13.5 ~ 18V 21.6 ~ 28.8V 28.8 ~ 39.6V 40.8 ~ 55.2V
VOLTAGE TOLERANCE Note.3 2.0% 2.0% 2.0% 1.0% 1.0% 1.0% 1.0% 1.0%
LINE REGULATION 0.5% 0.5% 0.5% 0.3% 0.3% 0.2% 0.2% 0.2%
LOAD REGULATION 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% 0.5%
SETUP, RISE TIME 1000ms, 50ms/230VAC 2500ms, 50ms/115VAC at full load
HOLD UP TIME (Typ.) 16ms/230VAC 16ms/115VAC at full load
VOLTAGE RANGE Note.5 85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE 47 ~ 63Hz
POWER FACTOR (Typ.) PF>0.94/230VAC PF>0.99/115VAC at full load
INPUT EFFICIENCY (Typ.) 78.5% 82% 87% 88% 88% 88% 89% 89%
AC CURRENT (Typ.) 8.5A/115VAC 5A/230VAC
INRUSH CURRENT (Typ.) 35A/115VAC 70A/230VAC
LEAKAGE CURRENT <1.2mA / 240VAC
105 ~ 135% rated output power
OVERLOAD
Protection type : Constant current limiting, recovers automatically after fault condition is removed
3.96 ~ 4.62V 6 ~ 7V 9.4 ~ 10.9V 14.4 ~ 16.8V 18.8 ~ 21.8V 30 ~ 34.8V 41.4 ~ 48.6V 57.6 ~ 67.2V
OVER VOLTAGE
PROTECTION Protection type : Shut down o/p voltage, re-power on to recover
80 5 (TSW1)detect on heatsink of power transistor
OVER TEMPERATURE 90 5 (TSW2) detect on heatsink of power doide for 3.3V,5V,7.5V ; 100 5 (TSW2) detect on main power output choke for others
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
DC OK SIGNAL PSU turn on : 3.3 ~ 5.6V ; PSU turn off : 0 ~ 1V
FUNCTION
FAN CONTROL (Typ.) Load 35 15% or RTH2 50 Fan on
WORKING TEMP. -40 ~ +70 (Refer to "Derating Curve")
WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH
TEMP. COEFFICIENT 0.03%/ (0 ~ 50 )
VIBRATION 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS UL60950-1, TUV EN60950-1 approved
SAFETY & WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
(Note 4) EMC EMISSION Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3
EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2, heavy industry level, criteria A
MTBF 140.6K hrs min. MIL-HDBK-217F (25 )
OTHERS DIMENSION 218*105*63.5mm (L*W*H)
PACKING 1.5Kg;8pcs/13Kg/1.34CUFT
NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
5. Derating may be needed under low input voltages. Please check the derating curve for more details.

File Name:HRP-600-SPEC 2011-08-09

 600W Single Output with PFC Function HRP-600 series

Mechanical Specification Case No. 977A Unit:mm

152.4 32.8

20.75
O/P
1

11
4-M4 L=6
2
Air flow
3
direction

63.5

105
9.2
4
I/P 5
8.2

1 6
2
10

1 3
3 2 4

CN100
LED
SVR1
(Vo ADJ.)
218
152.4 32.8

8-M4 L=4 (Both Sides) 18max.

12max.

38.3
63.5
12.5
AC Input Terminal Pin No. DC Output Terminal Pin No. Connector Pin No. Assignment(CN100) : HRS DF11-4DP-2DS or equivalent
Assignment Assignment Pin No. Assignment Mating Housing Terminal
Pin No. Assignment Pin No. Assignment 1 DC-OK
1 AC/L 1~3 -V 2 GND HRS DF11-4DS HRS DF11-**SC
2 AC/N 4~6 +V 3 +S or equivalent or equivalent
3 FG 4 -S

Block Diagram
PW M fosc : 70KHz
+S
ACTIVE RECTIFIERS RECTIFIERS
EMI INRUSH POWER +V
I/P FILTER & &
CURRENT SWITCHING -V
LIMITING PFC FILTER
-S

O.T.P. O.L.P.
FG DETECTION
CIRCUIT DC OK
O.T.P.
PFC PWM
CONTROL CONTROL O.V.P.

Derating Curve Output Derating VS Input Voltage

125 100

90
100
80
80
70
LOAD (%)

60
LOAD(%)

50

50

20 40

-40 0 10 20 30 40 50 60 65 70 (HORIZONTAL) 85 100 125 135 155 264

AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz

File Name:HRP-600-SPEC 2011-08-09