Warranty

2+1 *
years

Renesa Halo
Ceiling fan
INSTRUCTION MANUAL

Home App

ATOMBERG TECHNOLOGIES PVT LTD

Registered office : Atomberg Technologies Pvt Ltd, 3rd Floor, Tower B, 247 Embassy Park, LBS Marg,
Vikhroli West, Mumbai, Maharashtra, India, Pin Code - 400083

Manufacturing unit : Atomberg Technologies Private Limited, Mind Space Shelters LLP / Vithai
Developers LLP Gat No. 51-59; Bhamboli, Chakan, Pune, Maharashtra, India, Pin Code - 410507

For an additional 1 year extension, kindly register the warranty.

*
PACKAGE CONTENTS TOOLS NEEDED

Pliers

Screw driver
Motor 3 Blades Shackle kit

Tester for
wire connection

Open end spanners

Downrod 2 Canopies Canopy plate Remote

+ Step ladder
2 Batteries

To avoid risk of fire, shock & injury -

- Only use the product as intended by Atomberg
- The wiring of the fan must be done by a qualified person or trained electrician
- For any product related queries, please contact Atomberg

What makes Atomberg ceiling fans best in class?

• Energy-efficient BLDC motor that saves up to 65% energy

• Runs 3x longer on inverter leading to longer inverter runtime
• Less heating of fan even after long hours of runtime, resulting in longevity
• Consistent speed even at low voltages
• Universal remote - without pairing for easy speed controls
• Double ball bearing for higher reliability
• Moisture resistant protective coating on PCB
• Every fan is tested for durability in extreme Indian conditions
 SAFETY INSTRUCTIONS
Please read carefully before assembling and installing the fan to avoid any risk of
injury or damage to the product.
1. Do not install the fan if any part is damaged or missing.
2. Only use Atomberg-approved parts or accessories supplied with this product and/or
any accessories designed specifically for this product by Atomberg. Any such use of
other parts or accessories may turn the product warranty null and void, and may
result in personal injury or property damage.
3. Not recommended for use in high-humid areas with direct or indirect exposure to
water entries.
4. Installation warnings:
- Secure blades properly with screws and washer to avoid injury during operation.
An imbalanced fan may damage the motor and reduce the lifetime of the fan.
- Damage from incorrect installation or improper practices are not covered under the
warranty terms. Please check the warranty terms in detail.
- Do not turn on the fan until the blades are securely fastened to the ceiling fan.
- Any connection to wires must be securely sealed using electrical insulation tape to
prevent electric shock or fire hazard.
- Avoid pinching wires between the shackle kit, down rod and ceiling hook to prevent
electric shock or fire hazard.
5. Bypassing regulator:
- Eliminate regulator by using a direct connection from the switch to the fan and
do not use the regulator as the fan is operated using a remote.
- Not bypassing the regulator may lead to speed variations, restarting, low speed or
product damage.
6. Additional:
- Be careful while cleaning the fan or painting/working near the fan. Always turn off
the power to the ceiling fan before servicing or cleaning.
- Do not put your hand or any other objects near the fan blades while the fan is
running.
- Do not modify the blade design to change the air flow.
- Children should be supervised to not play with the appliance.
- This appliance is not for use by persons (including children) with reduced physical,
sensory, or mental abilities, or lack of experience, unless supervised by someone
responsible for their safety.
- Dispose off electrical parts at designated collection facilities. Contact local
authorities for disposal options. Avoid landfills to protect the environment.
Please note:
In case of remote model:
1. The fan will not function if the input voltage is more than 285V.
2. The fan will not function with square type inverter if the voltage is more than 285V and
400V peak.
In case of regulator model:
1. The fan will not function if the input voltage is more than 285V.
2. The fan will not function with square type inverter if the voltage is above 285V and 400V
peak.
3. For a better performance use step regulator as the fan will not operate at a lower range if
used with a non-compatible stepless (triac based) regulator.
 INSTALLATION
Please follow all steps to ensure efficient performance

01
Mandatory Step
Shackle kit
Bypass the regulator before installing your
Top canopy
Atomberg fan for optimal performance.
Downrod
Refer to the image for the correct order of
parts. Carefully remove the motor from the
Blade Bottom canopy
box and place it on soft padding to avoid
scratches.
Shaft with motor

1 IF 'H' >240mm

02
1 2
Fit the down rod, glide the
top canopy on it and fit
the bottom canopy.
CANOPY PLATE

'H'
DOWNROD BELOW CEILING
DOWNROD
2 IF 'H' <240mm
Glide the canopy plate on the
NOTE:
USE CANOPY PLATE IN CASE OF
FALSE CEILING.(IF DOWNROD IS
NOT FULLY VISIBLE).

down rod and use the bottom

canopy.

03
Blade assembly
Align the holes on the blade shank with
the motor holes. Securely fasten the blades
with the screws and washer provided.

04
Hanging the fan
Downrod
Insert the screw to assemble the shaft and
Bottom
the down rod. Insert the washer, nut and
Canopy
R-Pin in the sequence depicted in the
Screw
illustration below. Pull down the canopy to
Connector
cover the splice connector and screws.

Nut Spring washer

R pin Hex screw

05
Height & adjustments
For optimal performance and safety, the fan
Ceiling blades should have at least 1 foot of
At least 1 foot clearance from the ceiling. For low height
ceiling, refer step 2. Keep objects at least 2
feet away from the blade tips to reduce
At least 7.6 feet
injury or risk. The fan should be hung at least
7.6 feet from the floor to the blades.
Floor

06
Electrical wiring instruction
Rotate the splice connector anticlockwise
to remove it from the power wires (red,
black). Twist it with the input supply wires,
then insert the splice connector and rotate
clockwise to lock it securely.

OPERATING YOUR ATOMBERG CEILING FAN

1. Power 'ON' the ceiling fan using switch on the panel in the room.
2. The LED indicator flashes ‘ON’ when power supply is restored.
3. Use your remote to operate the ceiling fan.
4. If you are leaving the room or facility for a long duration or on holiday, then
power 'OFF' the ceiling fan using the switch on the panel.

Note: The product complies with the requirement of IS 374:2019, IS 302-2-80:2017 in

conjunction with IS 302-1:2008 with all applicable amendments.

MAINTENANCE
Periodic cleaning of your ceiling fan is the only maintenance needed.
When cleaning, use only a soft lint-free cloth or brush to avoid scratching the smooth
paint finish. You can use moist cloth to remove stains if any. However, do not use water
directly. Abrasive cleaning agents are not required and should be avoided to prevent
damage to the outer finishing.
 USING YOUR REMOTE

Remote
On/Off Function Description Indication
key
1 Speed 1 Sets the fan
to lowest speed
Speed control

Boost speed
2 Speed 2 Sets the fan
to speed 2

Sleep mode 3 Speed 3 Sets the fan

to speed 3
4 Speed 4 Sets the fan
LED On/Off to speed 4

Timer mode 5 Speed 5 Sets the fan

to speed 5
B Boost Sets the fan
Speed to highest speed

Longlasting AAA batteries are used in the remote

Sleep mode adds smart comfort, as the temperature drops over the night and if you
wish to auto-reduce the speed. Sleep mode will not work if fan is off.

With Timer mode you can switch OFF/ON the fan automatically after set hours to
further save energy.

Remote
Function Indication
key

Timer Fan automatically switches OFF/ON after LED will follow a turn ON-fade out
the set hours (1, 2, 3 & 6 Hrs) pattern of once each for the number
of hours the timer is set for:
1 hour: Once
2 hours: Twice
3 hours: Thrice
6 hours:Six times
OFF: Max brightness for 2 sec, then
fade in 1 sec

After initial 2 Hrs a Speed reduces by 1 step. First press: Turn ON SLEEP mode -
Sleep
Then after next 2 Hrs a Speed reduces by another LED lights up and fades out slowly
1 step and fan continues to run at this speed. over a second.
Second press: Turn OFF SLEEP mode -
LED stays on at full brightness for
2 seconds and then fades out over
a second.

LED LED On/Off First Press: Turn ON LED mode

Second Press: Turn OFF LED mode
 TROUBLESHOOTING

Your ceiling fan is built to last with a durable body and reliable electronics.
If issues arise, refer to the guidelines or contact a local electrician or
service engineer for assistance.

Problem Cause Solution

Fan does Fuse down / MCB shut off Check fuse of the MCB on the mains.
not start
Loose wire connection to fan Check the wire connection and restore the connection
or to the switch on the panel.

Fan still does not start Please contact the service number provided. It is recommended
Regulator is connected to that the regulator should not be connected to this ceiling fan
the fan. and it is instead controlled using the remote provided with it.

Fan Bearing inside the housing This ceiling fan is designed to be longlasting. However, after
making has problems. many years of use the bearing may wear off and may need to
noise be replaced.

Fan blades are not seated Make sure the blades are properly fastened to the body. Loose
properly on the motor. connection may cause accidents.
Shackle kit rattling. Make sure that the screws and nuts are securely fastened
along with washer provided.
Canopy is touching the Make sure that the canopy and/or the wire that connects
body / Canopy is touching the fan are not touching the body of the motor.
the ceiling. Make sure that the canopy is not touching the ceiling.

Fan is Nut holding motor shaft Securely fasten the nut and bolts along with washers as per
wobbling and the down rod is loose/ the instructions provided in this manual.
Nut holding down rod and
shackle kit is loose/Screws
in shackle kit and the ceiling
hook are loose.

Fan blades are not seated A common mistake is fixing the blade in the reverse direction.
properly on the motor. Please set it right and securely fasten the screws.

Fan blades are out of Make sure that the blades are not bent during cleaning. Also,
balance. interchanging them helps balance the blades.

Continouous Regulator not bypassed. Make sure the regulator is eliminated from the connection.
LED blinking

Restart Blades have wrong sweep. Check the sweep of blades with the fan sweep before
& speed assembling.
variation
HOW TO CONNECT TO ALEXA USING THE ALEXA APP
1. In the Alexa app, navigate to the 'Skills and Games' option and search for
'Atomberg Home'
2. Click on the skill that shows up and then click on 'Enable'
3. As part of user verification again the login page might appear. Use the same login
method (Google/Facebook/Apple/Email) used on the Atomberg Home app to
proceed.
4. Alexa will be linked
5. If you purchased your Alexa device in the USA, this is the recommended approach

HOW TO CONNECT TO GOOGLE HOME USING THE

GOOGLE HOME APP
1. In the Google Home app, navigate to the 'Devices' section, and click on the '+' icon
to add a device. Then click on 'Works with Google Home'
2. Search for Atomberg Home. An approval page will open up. Click on 'Continue'
3. After few seconds account verification popup may appear -> Use the same login
method (Google/Facebook/Apple/Email) used on the Atomberg Home app to
proceed.
4. Will ask to choose the device -> click & press next
5. Google Home will ask you to create the family if no family is there.
6. Enter the Home name
7. You can add address if wanted, else skip
8. Choose the created home
9. It is successfully linked
HOW TO CONNECT TO ALEXA USING THE ATOMBERG
HOME APP
1. In the Atomberg Home app, navigate to the 'More' section and click on the
'Connect' button next to Alexa for linking
2. Confirm if Alexa app is already installed or not
3. If it is installed then the Alexa app will automatically open -> Link
4. As part of user verification again the login page might appear. Use the same login
method (Google/Facebook/Apple/Email) used on the Atomberg Home app to
proceed.
5. Alexa will be linked

HOW TO CONNECT TO GOOGLE HOME USING THE

ATOMBERG HOME APP
1. In the Atomberg Home app, navigate to the 'More' section and click on the
'Connect' button next to 'Google' for linking-> if Google Home is installed then it
will open it else you will be asked to download it.
2. Wait for a few seconds. An approval page will open up. Click on 'Continue'
3. After few seconds account verification popup may appear -> Use the same login
method (Google/Facebook/Apple/Email) used on the Atomberg Home app to
proceed.
4. Will ask to choose the device -> click & press next
5. Google Home will ask you to create the family if no family is there
6. Enter the Home name
7. You can add address if wanted, else skip
8. Choose the created home
9. It is successfully linked
HOW TO CONNECT WITH ATOMBERG HOME APP
1. Tap on Add device, all scannable Atomberg devices nearby will show up on the
radar
2. Once you see a device show up on the radar, tap on the 'Connect' button so that it
starts pairing. Select the model and color of your product.
3. For identification fan name, room name is needed which can be quickly selected
using suggestions
4. If the available suggestions are not satisfactory, then choose the custom option
and enter your own values for fan/room
5. Wifi Details for making it smart -> Enter Wifi name (SSID) -> Password. If you
choose to remember the password then while adding another device password
will get auto fetched
6. Wait for a minute or so for the device to get added
7. It will prompt if device gets added successfully. If it fails then retry again ensuring
the WiFi has the internet connectivity
8. Once added the device will be visible on home screen

*Google, Alexa, Facebook, and Apple are registered trademarks of their respective organizations.
 HOW TO REGISTER THE WARRANTY?

ONLINE REGISTRATION
• Log in to www.atomberg.com
• Navigate to “register-warranty-card”
• Enter product serial number/barcode (mentioned on the warranty card/box)
and other details.
SCAN QR code for
VIA CALL
• Call us on "84484 49442"
or
• Select your language
• Select '3' for warranty registration
• You will receive a warranty link
via 'SMS' or a call back for warranty registration
remaining details

FAN LIMITED WARRANTY

Atomberg Technologies Private Limited warrants that this product is to be free from any
manufacturing defects in material and workmanship under normal use from the date of
purchase as evidenced by the purchase receipt. This warranty provided by Atomberg
Technologies Private Limited to you is for a period of 2+1 years*.

• Warranty duration:

Part Name Warranty duration from Date of Purchase**

Motor** 2+1* (years)

Accessories: Downrod, Canopy

Against transit damage within 7 days of delivery
Shackle kit, Battery, etc.

Remote, Blade** 1 Year

This warranty card is an addition and does not imply any loss of statutory rights.
After warranty card registration
* **
Against Manufacturing defects

Note: All the transit damage or missing items cases should be registered within 7 days
of product delivery to pass the warranty claim.
 WARRANTY TERMS AND CONDITIONS

• The warranty explicitly provided for herein is the sole warranty provided in
connection with the product and no other warranty, expressed or implied, is
provided.
• Atomberg assumes no responsibility for any other claims, especially ones not stated
in this warranty.
• The company’s liability will never exceed the value of the product.
• The company will not be responsible for delay in repair/service due to unavoidable
circumstances.
• This warranty is only valid within the states and union territories of India.
• No other written or oral warranties apply, and no other agent, employee, dealer or
any other person is authorized to give any warranties (explicit or otherwise) on
behalf of Atomberg.
• This warranty does not include and expressly excludes:
- Loss or damage to the motor or any accessory caused by normal wear and
tear rather than due to defect in materials or workmanship.
- Loss or damage resulting from improper installation or other failure to
comply with instructions given in your owner’s manual.
- Loss or damage resulting from conditions beyond our reasonable control,
including without limitation, repairs not made at our factory or authorized
service provider, use of parts or accessories not provided to you as part of
this warranty by our factory or authorized service providers or mishandling,
unreasonable use, misuse, abuse, modifications or other damages caused
by you or a third party to your fan while not in our possession.

To know more about warranty terms and latest guidelines kindly visit related section on
www.atomberg.com

How to avail this service under warranty terms:

1. Registering your barcode is mandatory to avail warranty services.
2. Your sales bill with full purchase details and this fully completed warranty card
must be presented when warranty services are required.
3. This warranty service must be performed at our factory, or with authorized
service providers who are affiliated to the atomberg warranty system.
4. When returning the product for warranty service, please pack it carefully,
enclose the bill, the warranty card and the instructions for repair.
5. If the warranty card is lost, then it cannot be re-issued.