80 SERIES 80

Modular timers 16 A SERIES

Multi-function and mono-function timer range 80.01 80.11

80.01 - Multi-function & multi-voltage
80.11 - On-delay, multi-voltage
• 17.5 mm wide
• Six time scales from 0.1 s to 24 h
• High input/output isolation
• 35 mm rail (EN 60715) mount
• “Blade + cross” - both flat blade and cross head
screw drivers can be used to adjust the range
and function selectors, the timing trimmer, and
to disengage the rail mounting clip
• New multi-voltage versions with “PWM clever” • Multi-voltage • Multi-voltage
technology • Multi-function • Mono-function
AI: On-delay AI: On-delay
80.01 / 80.11 DI: Interval
Screw terminal SW: Symmetrical flasher (starting pulse on)
BE: Off-delay with control signal
CE: On- and off-delay with control signal
DE: Interval with control signal on

For UL ratings see:

“General technical information” page V
Wiring diagram Wiring diagram Wiring diagram
For outline drawing see page 6 (without control signal) (with control signal) (without control signal)
Contact specification
Contact configuration 1 CO (SPDT) 1 CO (SPDT)
Rated current/Maximum peak current A 16/30 16/30
Rated voltage/ H
Maximum switching voltage V AC 250/400 250/400
Rated load AC1 VA 4000 4000
Rated load AC15 (230 V AC) VA 750 750
Single phase motor rating (230 V AC) kW 0.55 0.55
Breaking capacity DC1: 30/110/220 V A 16/0.3/0.12 16/0.3/0.12
Minimum switching load mW (V/mA) 500 (10/5) 500 (10/5)
Standard contact material AgNi AgNi
Supply specification
Nominal voltage (UN) V AC (50/60 Hz) 12…240 24…240
V DC 12…240 24…240
Rated power AC/DC VA (50 Hz)/W < 1.8/< 1 < 1.8/< 1
Operating range V AC 10.8…265 16.8…265
V DC 10.8…265 16.8…265
Technical data
Specified time range (0.1…2)s, (1…20)s, (0.1…2)min, (1…20)min, (0.1…2)h, (1…24)h
Repeatability% ±1 ±1
Recovery time ms 100 100
Minimum control impulse ms 50 —
Setting accuracy-full range % ±5 ±5
XI-2016, www.findernet.com

Electrical life at rated load in AC1 cycles 50 · 103 50 · 103

Ambient temperature range °C –10…+50 –10…+50
Protection category IP 20 IP 20
Approvals (according to type)

1
80 80 SERIES
SERIES Modular timers 16 A

Mono-function timer range 80.21 80.41 80.91

80.21 - Interval, multi-voltage
80.41 - Off-delay with control signal, multi-voltage
80.91 - Asymmetrical flasher, multi-voltage
• 17.5 mm wide
• Six time scales from 0.1 s to 24 h
• High input/output isolation
• 35 mm rail (EN 60715) mount
• “Blade + cross” - both flat blade and cross head
screw drivers can be used to adjust the range
and function selectors, the timing trimmer, and
to disengage the rail mounting clip • Multi-voltage • Multi-voltage • Multi-voltage
• New multi-voltage versions with “PWM clever” • Mono-function • Mono-function • Mono-function
technology DI: Interval BE: Off-delay with control signal LI: Asymmetrical flasher
(starting pulse on)
80.21 / 80.41 / 80.91 LE: Asymmetrical flasher (starting
Screw terminal pulse on) with control signal

For UL ratings see:

“General technical information” page V Wiring diagram Wiring diagram
Wiring diagram Wiring diagram (without control (with control
For outline drawing see page 6 (without control signal) (with control signal) signal) signal)
Contact specification
Contact configuration 1 CO (SPDT) 1 CO (SPDT) 1 CO (SPDT)
Rated current/Maximum peak current A 16/30 16/30 16/30
H Rated voltage/
Maximum switching voltage V AC 250/400 250/400 250/400
Rated load AC1 VA 4000 4000 4000
Rated load AC15 (230 V AC) VA 750 750 750
Single phase motor rating (230 V AC) kW 0.55 0.55 0.55
Breaking capacity DC1: 30/110/220 V A 16/0.3/0.12 16/0.3/0.12 16/0.3/0.12
Minimum switching load mW (V/mA) 500 (10/5) 500 (10/5) 500 (10/5)
Standard contact material AgNi AgNi AgNi
Supply specification
Nominal voltage (UN) V AC (50/60 Hz) 24…240 24…240 12…240
V DC 24…240 24…240 12…240
Rated power AC/DC VA (50 Hz)/W < 1.8/< 1 < 1.8/< 1 < 1.8/< 1
Operating range V AC 16.8…265 16.8…265 10.8…265
V DC 16.8…265 16.8…265 10.8…265
Technical data
Specified time range (0.1…2)s, (1…20)s, (0.1…2)min, (1…20)min, (0.1…2)h, (1…24)h
Repeatability% ±1 ±1 ±1
Recovery time ms 100 100 100
Minimum control impulse ms — 50 50
Setting accuracy-full range % ±5 ±5 ±5
XI-2016, www.findernet.com

Electrical life at rated load in AC1 cycles 50 · 103 50 · 103 50 · 103

Ambient temperature range °C –10…+50 –10…+50 –10…+50
Protection category IP 20 IP 20 IP 20
Approvals (according to type)

2
 80 SERIES 80
Modular Solid State timer (SST) 1 A SERIES

Multi-function and multi-voltage solid-state 80.71

output timer
• 17.5 mm wide
• Six time scales from 0.1 s to 24 h
• High input/output isolation
• 35 mm rail (EN 60715) mount
• Multi-voltage output (24…240 V AC/DC),
independent from the input voltage
• “Blade + cross” - both flat blade and cross head
screw drivers can be used to adjust the range
and function selectors, the timing trimmer, and
to disengage the rail mounting clip • Multi-voltage
• Multi-voltage input with “PWM clever” • Multi-function
technology AI: On-delay
DI: Interval
80.71 SW: Symmetrical flasher (starting pulse on)
Screw terminal BE: Off-delay with control signal
CE: On- and off-delay with control signal
DE: Interval with control signal on

Wiring diagram Wiring diagram

For outline drawing see page 6 (without control signal) (with control signal)
Output circuit
Contact configuration 1 NO (SPST-NO)
Rated current A 1 H
Rated voltage V AC/DC 24…240
Switching voltage range V AC/DC 19…265
Rated load AC15 A 1
Rated load DC1 A 1
Minimum switching current mA 0.5
Max. “OFF-state” leakage current mA 0.05
Max. “ON-state” voltage drop V 2.8
Input circuit
Nominal voltage (UN) V AC (50/60 Hz) 24…240
V DC 24…240
Rated power VA (50 Hz)/W 1.3/1.3
Operating range V AC 19…265
V DC 19…265
Technical data
Specified time range (0.1…2)s, (1…20)s, (0.1…2)min, (1…20)min, (0.1…2)h, (1…24)h
Repeatability% ±1
Recovery time ms 100
Minimum control impulse ms 50
Setting accuracy-full range % ±5
XI-2016, www.findernet.com

Electrical life cycles 100 · 106

Ambient temperature range °C –20…+50
Protection category IP 20
Approvals (according to type)

3
80 80 SERIES
SERIES Modular timers 6 - 8 A

Mono-function timer range 80.61 80.82

80.61 - Power off-delay (True off-delay),
multi-voltage
80.82 - Star-delta, multi-voltage
• 17.5 mm wide
• Rotary range selector, and timing trimmer
• Four time scales from 0.05s to 3 min (type 80.61)
• Six time scales from 0.1 s to 20min (type 80.82)
• High input/output isolation
• 35 mm rail (EN 60715) mount
80.61 / 80.82 • Multi-voltage • Multi-voltage
Screw terminal • Mono-function • Mono-function
• Transfer time can be regulated (0.05…1)s
BI: Power off-delay (True off-delay) SD: Star-delta

For UL ratings see:

“General technical information” page V
Wiring diagram Wiring diagram
For outline drawing see page 6 (without control signal) (without control signal)
Contact specification
Contact configuration 1 CO (SPDT) 2 NO (DPST-NO)
Rated current/Maximum peak current A 8/15 6/10
H Rated voltage/
Maximum switching voltage V AC 250/400 250/400
Rated load AC1 VA 2000 1500
Rated load AC15 (230 V AC) VA 400 300
Single phase motor rating (230 V AC) kW 0.3 —
Breaking capacity DC1: 30/110/220 V A 8/0.3/0.12 6/0.2/0.12
Minimum switching load mW (V/mA) 300 (5/5) 500 (12/10)
Standard contact material AgNi AgNi
Supply specification
Nominal voltage (UN) V AC (50/60 Hz) 24…240 24…240
V DC 24…220 24…240
Rated power AC/DC VA (50 Hz)/W < 0.6/< 0.6 < 1.3/< 0.8
Operating range V AC 16.8…265 16.8…265
V DC 16.8…242 16.8…265
Technical data
Specified time range (0.05…2)s, (1…16)s, (8…70)s, (50…180)s (0.1…2)s, (1…20)s, (0.1…2)min, (1…20)min
Repeatability% ±1 ±1
Recovery time ms — 100
Minimum control impulse ms 500 (A1-A2) —
Setting accuracy-full range % ±5 ±5
XI-2016, www.findernet.com

Electrical life at rated load in AC1 cycles 100 · 103 60 · 103

Ambient temperature range °C –10…+50 –10…+50
Protection category IP 20 IP 20
Approvals (according to type)

4
 80 SERIES 80
Modular timers 1 - 6 - 8 - 16 A SERIES

Ordering information
Example: 80 series, modular timers, 1 CO (SPDT) - 16 A, supply rated at (12…240)V AC/DC.

8 0 . 0 1 . 0 . 2 4 0 . 0 0 0 0
Series Versions
Type 0 = Standard
0 = Multi-function (AI, DI, SW, BE, CE, DE) Supply voltage
1 = On-delay (AI) 240 = (12…240)V AC/DC (80.01, 80.91)
2 = Interval (DI) 240 = (24…240)V AC/DC (80.11, 80.21, 80.41, 80.71, 80.82)
4 = Off-delay with control signal (BE) 240 = (24…240)V AC, (24…220)V DC (80.61)
6 = Power off-delay (True off-delay) (BI) Supply version
7 = Multi-function with solid state output 0 = AC (50/60 Hz)/DC
(AI, DI, SW, BE, CE, DE)
No. of poles
8 = Star-delta (SD)
1 = 1 CO (SPDT)
9 = Asymmetrical flasher (LI, LE)
1 = 1 NO (SPST-NO), type 80.71 only
2 = 2 NO (DPST-NO), type 80.82 only

Technical data
Insulation
Dielectric strength 80.01/11/21/41/82/91 80.61 80.71
between input and output circuit V AC 4000 2500 2500
between open contacts V AC 1000 1000 —
Insulation (1.2/50 µs) between input and output kV 6 4 4
EMC specifications
Type of test Reference standard 80.01/11/21/41/61/71/91 80.82
Electrostatic discharge contact discharge EN 61000-4-2 4 kV 4 kV
air discharge EN 61000-4-2 8 kV 8 kV
Radio-frequency electromagnetic field (80 ÷ 1000 MHz) EN 61000-4-3 10 V/m 10 V/m
Fast transients (burst) (5-50 ns, 5 kHz) on Supply terminals EN 61000-4-4 4 kV 4 kV
Surges (1.2/50 µs) on Supply terminals common mode EN 61000-4-5 4 kV 4 kV
differential mode EN 61000-4-5 4 kV 4 kV
on start terminal (B1) common mode EN 61000-4-5 4 kV 4 kV
differential mode
Radio-frequency common mode (0.15 ÷ 80 MHz) on Supply terminals
EN 61000-4-5
EN 61000-4-6
4 kV
10 V
4 kV
10 V
H
Radiated and conducted emission EN 55022 class B class A
Other data
Current absorption on signal control (B1) < 1 mA
Power lost to the environment without contact current W 1.4
with rated current W 3.2
Screw torque Nm 0.8
Max. wire size solid cable stranded cable
mm2 1 x 6 / 2 x 4 1 x 4 / 2 x 2.5
AWG 1 x 10 / 2 x 12 1 x 12 / 2 x 14

Accessories
Sheet of marker tags, for types 80.82, plastic, 24 tags, 9 x 17 mm 020.24

020.24

Sheet of marker tags (CEMBRE'S Thermal transfer printers) for relays types
060.48
80.01/11/21/41/61/71 (48 tags), 6 x 12 mm
XI-2016, www.findernet.com

060.48

5
80 80 SERIES
SERIES Modular timers 1 - 6 - 8 - 16 A

Outline drawings
80.01 80.11
Screw terminal Screw terminal

80.21 80.41
Screw terminal Screw terminal

80.91 80.71
Screw terminal Screw terminal

80.61 80.82
Screw terminal Screw terminal
XI-2016, www.findernet.com

6
 80 SERIES 80
Modular timers 1 - 6 - 8 - 16 A SERIES

Functions
U = Supply voltage NO output Contacts
LED* Supply voltage
contact Open Closed
S = Signal switch
OFF Open 15 - 18 15 - 16
= Output contact
ON Open 15 - 18 15 - 16

Open
ON 15 - 18 15 - 16
(Timing in Progress)

ON Closed 15 - 16 15 - 18

* The LED on type 80.61 is illuminated only when the supply voltage is applied to the timer; during the timing period the LED
is not illuminated.

Without control signal = Start via contact in supply line (A1).

Wiring diagram With control signal = Start via contact into control terminal (B1).
Without control signal Type (AI) On-delay.
80.01 Apply power to timer. Output contacts transfer after preset
80.71 time has elapsed. Reset occurs when power is removed.

(DI) Interval.
Apply power to timer. Output contacts transfer immediately.
80.01 After the preset time has elapsed, contacts reset.

(SW) Symmetrical flasher (starting pulse on).

Apply power to timer. Output contacts transfer immediately
and cycle between ON and OFF for as long as power is applied.
The ratio is 1:1 (time on = time off ).

80.71

With control signal 80.01 (BE) Off-delay with control signal.

80.71 Power is permenently applied to the timer. The output
contacts transfer immediately on closure of the Signal Switch H
(S). Opening the Signal Switch initiates the preset delay, after
which time the output contacts reset.
(CE) On- and off-delay with control signal.
80.01 Power is permenently applied to the timer. Closing the Signal
Switch (S) initiates the preset delay, after which time the output
contacts transfer. Opening the Signal switch initiates the same
preset delay, after which time the output contacts reset.

(DE) Interval with control signal on.

Power is permenently applied to the timer.
On momentary or maintained closure of Signal Switch (S), the
80.71
output contacts transfer, and remain so for the duration of the
preset delay, after which they reset.

NOTE: The function must be set before energising the timer.

• Possible to control an external load, such as another relay coil or timer, connected to the control signal terminal B1.

* With DC supply, positive polarity has to be connected to B1 terminal (according to EN 60204-1).

XI-2016, www.findernet.com

** A voltage other than the supply voltage can be applied to the command Start (B1), example:
A1 - A2 = 230 V AC
B1 - A2 = 12 V DC

7
80 80 SERIES
SERIES Modular timers 6 - 8 - 16 A

Functions
Wiring diagram
Without control signal Type (AI) On-delay.
80.11 Apply power to timer. Output contacts transfer after preset
time has elapsed. Reset occurs when power is removed.

80.21 (DI) Interval.

Apply power to timer. Output contacts transfer immediately.
After the preset time has elapsed, contacts reset.

80.11/21/61
80.61 (BI) Power off-delay (True off-delay).
Apply power to timer (minimum 500 ms). Output contacts
transfer immediately. Removal of power initiates the preset
delay, after which time the output contacts reset.

80.82 (SD) Star-delta.

Apply power to timer. The star contact ( ) closes immediately.
After preset delay has elapsed the star contact ( ) resets.
After a further transfer time variable from (0.05…1)s the delta
contact ( ∆ ) closes and remains in that position, until reset on
80.82 power off.

With control signal 80.41 (BE) Off-delay with control signal.

Power is permenently applied to the timer.
The output contacts transfer immediately on closure of the
Signal Switch (S). Opening the Signal Switch initiates the preset
delay, after which time the output contacts reset.

80.41
Without control signal 80.91 (LI) Asymmetrical flasher (starting pulse on).
Apply power to timer. Output contacts transfer immediately
and cycle between ON and OFF for as long as power is applied.
The ON (T1) and OFF (T2) times are independently adjustable.
H

(LE) Asymmetrical flasher (starting pulse on) with control

80.91
signal
With control signal Power is permenently applied to the timer.
Closing Signal Switch (S) causes the output contacts to transfer
immediately and cycle between ON (T1) and OFF (T2), until
opened.

80.91

• Possible to control an external load, such as another relay coil or timer, connected to the control signal terminal B1.

* With DC supply, positive polarity has to be connected to B1 terminal (according to EN 60204-1).

XI-2016, www.findernet.com

** A voltage other than the supply voltage can be applied to the command Start (B1), example:
A1 - A2 = 230 V AC
B1 - A2 = 12 V DC