LCT Installation Manual (LIM)
7090
5.0
Revision 12, November 2020
A42022-L5984-A055-12-7630
Coriant is continually striving to reduce the adverse environmental effects
of its products and services. We would like to encourage you as our
customers and users to join us in working towards a cleaner, safer
environment. Please recycle product packaging and follow the
recommendations for power use and proper disposal of our products and
their components.
The information in this document is subject to change without notice and describes only the product defined in the
introduction of this documentation. This documentation is intended for the use of Coriant customers only for the
purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced,
modified or transmitted in any form or means without the prior written permission of Coriant. The documentation has
been prepared to be used by professional and properly trained personnel, and the customer assumes full
responsibility when using it. Coriant welcomes customer comments as part of the process of continuous development
and improvement of the documentation.
The information or statements given in this documentation concerning the suitability, capacity, or performance of the
mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or
software products shall be defined conclusively and finally in a separate agreement between Coriant and the
customer. However, Coriant has made all reasonable efforts to ensure that the instructions contained in the document
are adequate and free of material errors and omissions. Coriant will, if deemed necessary by Coriant, explain issues
which may not be covered by the document. Coriant will correct errors in this documentation as soon as possible.
IN NO EVENT WILL CORIANT BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES,
INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY
LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION,
BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE
INFORMATION IN IT.
FCC Notification Federal Communications Commission (FCC) Rules require that you be notified of the following:
Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at their own expense.
Changes or modifications not expressly approved by Coriant Operations, Inc., in writing can void the user’s authority
to operate the equipment.
Industry Canada Industry Canada interference-causing equipment regulations require that you be notified of the following:
Notification This Class A digital apparatus complies with Canadian ICES-003.
Statement
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Voluntary Control
Council for
Interference
(VCCI)
Copyright This manual is protected by U.S. and international copyright laws, conventions, and treaties. Your right to use this
Statement manual is subject to limitations and restrictions imposed by applicable licenses and copyright laws. Unauthorized
reproduction, modification, distribution, display or other use of this manual may result in criminal and civil penalties.
Trademark The following trademarks and service marks are owned by Coriant Operations, Inc., or its affiliates in the United
Notice States and/or other countries: Coriant®, Coriant CloudWave™, Coriant Dynamic Optical Cloud®, Coriant Groove™,
Coriant Transcend®, mTera®, Nano™, Pico™, and the Coriant Logos. Any other company or product names may be
trademarks of their respective companies.
Important Notice This product may present safety risks due to laser, electricity, heat, and other sources of danger.
on Product
Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after
Safety having carefully read the safety information applicable to this product.
The safety information is provided in the “Safety Instructions”, part of this document or documentation set.
The same text in
German:
Wichtiger Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen
Hinweis zur ausgehen.
Produktsicherheit
Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes
Personal unter Beachtung der anwendbaren Sicherheitsanforderungen erfolgen.
Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ dieses Dokuments oder dieses
Dokumentationssatzes.
Copyright © Coriant 2020. All rights reserved.
A42022-L5984-A055-12-7630 Page 2 Rev 12, November 2020
LCT Installation Manual (LIM) Table of Contents
Table of Contents
This document has 11 pages.
1 Preface ........................................................................................................................... 5
2 Prerequisites ................................................................................................................... 6
2.1 Software/Hardware Requirements .................................................................................. 6
2.2 Other Requirements ....................................................................................................... 6
3 Installing LCT .................................................................................................................. 7
3.1 Prerequisites ................................................................................................................... 7
3.2 Installation Procedures ................................................................................................... 7
3.3 Installation Verification .................................................................................................. 10
3.4 LCT Uninstallation ........................................................................................................ 11
A42022-L5984-A055-12-7630 Page 3 Rev 12, November 2020
LCT Installation Manual (LIM) History of changes
History of changes
Issue Issue Date Remarks
1 November 2013 Released the initial version
2 June 2014 Added minor updates.
3 December 2014 Updated for Rel. 2.0 10.
4 October 2015 Updated for Rel. 3.0.
5 July 2016 Updated for Rel. 3.0 10.
6 December 2016 Added minor updates.
7 April 2017 Added minor updates.
8 February 2018 Updated for Rel. 4.0
9 June 2018 Added minor updates.
10 August 2018 Updated for Rel. 4.1.
11 January 2020 Updated for Rel. 4.1 02.
12 November 2020 Updated for Rel. 5.0.
A42022-L5984-A055-12-7630 Page 4 Rev 12, November 2020
LCT Installation Manual (LIM) Preface
1 Preface
This manual provides instructions for 7090 Local Craft Terminal (LCT) installation
including prerequisites and detailed procedures.
LCT Installation Manual is intended for:
Technical support engineers
System maintenance engineers
Installation and test engineers
A42022-L5984-A055-12-7630 Page 5 Rev 12, November 2020
LCT Installation Manual (LIM) Prerequisites
2 Prerequisites
2.1 Software/Hardware Requirements
Table 1 lists the HW and SW requirements for LCT installation on a notebook/PC.
Item Description
- Windows XP Professional SP3
Software
- Windows 7 Professional
- Processor Pentium 4 with 2.0 GHz
- Monitor resolution with 1600 x 1200 / 1440 x 900
- 2 GB RAM or above
Hardware - 80 GB HDD or above
- 100 M Ethernet card
- Sound card
- Audio system
Table 1 Software/hardware requirements
2.2 Other Requirements
The resolution is set to 1600 x 1200 or 1440 x 900.
Ensure that the LCT installation CD-ROM is available.
The monitor display resolution and colour depth are properly set.
The colour depth is set to 32 bit.
The TCP/IP protocol is installed.
The IP address is properly set.
The Ethernet interface on your PC is enabled.
The printer is properly configured if necessary.
The communication port between the server and client is enabled on firewall.
The ports available for 7090 LCT includes:
Port Number Description
3333_out The port communicating with NE
22_in/out The port used by LCT for sftp upgrade
A42022-L5984-A055-12-7630 Page 6 Rev 12, November 2020
LCT Installation Manual (LIM) Installing LCT
3 Installing LCT
3.1 Prerequisites
Refer to Chapter 2 for details.
3.2 Installation Procedures
1. Initiate the installation by double-clicking7090M LCT_5.0 00.00.00 Build
3.14.1_B8.exe in the CD-ROM.
2. Proceed to the welcome page and click the Next button.
3. Proceed to the license agreement page, and click the I Agree button to continue
the installation if you agree the statement.
If you do not accept the license agreement, click the Cancel button to quit the
installation.
A42022-L5984-A055-12-7630 Page 7 Rev 12, November 2020
LCT Installation Manual (LIM) Installing LCT
4. Specify the target directory and click the Next button.
A42022-L5984-A055-12-7630 Page 8 Rev 12, November 2020
LCT Installation Manual (LIM) Installing LCT
5. Specify the start menu folder and click the Install button.
A42022-L5984-A055-12-7630 Page 9 Rev 12, November 2020
LCT Installation Manual (LIM) Installing LCT
6. Click the Finish button to complete and quit from the installation. The LCT
shortcut is generated in the start menu and the desktop of your PC.
3.3 Installation Verification
After the LCT is installed on Windows, check whether the installation is successful by
performing the following steps:
1. Check whether a shortcut icon is generated.
2. The shortcut icon is created on the desktop of your PC.
3. The following menu items are created by choosing Start > All Programs > 7090M
LCT V5.0:
4. 7090M LCT V5.0
5. Uninstall
6. (Optional) Check whether the LCT is opened successfully after you double-click
the LCT shortcut icon on your PC desktop.
A42022-L5984-A055-12-7630 Page 10 Rev 12, November 2020
LCT Installation Manual (LIM) Installing LCT
3.4 LCT Uninstallation
Before uninstalling the LCT, make sure all LCT processes are terminated.
Uninstall the LCT as following steps:
1. Select Start > All Programs > 7090M LCT V5.0 > Uninstall, the confirmation
window pops up.
2. Click Yes to uninstall the LCT.
3. When the LCT is uninstalled and the confirmation dialog box is displayed, click
OK.
4. Verify that the LCT icon is deleted on desktop.
5. Check the installation folder and make sure the folder is deleted.
A42022-L5984-A055-12-7630 Page 11 Rev 12, November 2020
