JP1500

STANDARD SPECIFICATIONS
1. ENGINE
Perkins four stroke heavy duty high performance
industrial type diesel engine.

2. ENGINE FILTRATION SYSTEM

• Two Cartridge type dry air filters.
• Cartridge type fuel filter.
• Six Full flow lube oil filters.
All filters have replaceable elements.

3. TROPICAL COOLING RADIATOR

Radiator and cooling fan, complete with safety
guards, designed to cool the engine at high ambient
temperatures (consult your dealer for de-ration factors)

4. EXHAUST SYSTEM
Heavy duty Industrial Exhaust Silencer

Silencer noise reduction level 10 (dB)

Maximum allowable back pressure 5.0 (kPa)
POWERED BY:
5. CIRCUIT BREAKER TYPE
ABB 3 pole ACB (supplied disconnected and without
cables)*. (4 pole is optional)

Generating Set pictured may include optional accessories (contd.)

GENERATING SET MODEL (JP1500) ALTERNATOR DATA

Output Ratings Prime Standby Make Leroy Somer
380-415 V, 3 ph, 50 Hz, 1500 rpm 1500 KVA 1650 KVA Model LSA50.2L8
1200 KW 1320 KW No. of bearings 1
Ratings at 0.8 Power Factor Insulation class H
ENGINE / TECHNICAL DATA Total Harmonic Content <3.5%
Engine Make Perkins Wires 6
Engine Model 4012 - 46TAG2A Ingress Protection IP23
Governing Type Digital Excitation System AREP
Number of Cylinders 12 Winding Pitch 2/3 (n° 6S)
Cylinder Arrangement 60° Vee form AVR Model R450
Bore and Stroke mm 160 x 190 Overspeed 2250 mn-1
Displacement / Cubic Capacity litres 45.842 Voltage Regulation (steady) ± 0.5%
Induction System Turbocharged and air to air charge cooled Short Circuit Capacity 300% (3 In):10s
Cycle 4 stroke PMG Excitation System Available as Optional.
Combustion System Direct Injection
Compression Ratio 13.6:1 CONTROL PANEL
Rotation Anti-clockwise, viewed from flywheel end Make Deep Sea
Cooling System Water - cooled Model DSE7320
Frequency and Engine Speed 50Hz & 1500rpm
Prime Standby DSE7320 is an Auto Mains (Utility) Failure
Gross Engine Power kW (hp) 1331 (1785) 1459 (1957) Control Module. It is operated via the START,
STOP, AUTO and MANUAL soft touch membrane
Fuel Consumption @ 50% load L/hr 162 - buttons on the front panel. DSE7320 can be
@ 75% load L/hr 237 - controlled remotely using either a GSM Modem,
@ 100% load L/hr 301 335 Ethernet via DSE860/865 or via RS485.
Total Lubrication System Capacity litres 177 177 Protection:
Total Coolant Capacity litres 210 210 • Fail to start
Boost Pressure Ratio 3.1 3.4 • Low oil pressure
Exhaust Temperature: °C 455 455 • High engine temperature
Radiator Cooling Air Flow (Min): m3/sec 32.4 32.4 • U/O Voltage shutdown
Combustion Air Flow: m3/min 120 128 • U/O Frequency shutdown
Exhaust Gas Flow: m3/min 320 320 • Underspeed, Overspeed
Fuel Tank Capacity: litres • Loss of engine speed detection
N/A N/A
• High/Low battery voltage
• kW overload
• Unbalanced load
DIMENSIONS AND WEIGHT • Low fuel alarm (if fitted)
Length cm Width cm Height cm Weight* kg (wet) • Battery charger failure (if fitted)
530 220 240 10550 (Please refer to DSE7320 brochure for more details)

* For skid mounted genset without enclosure wet weight = with lube oil and coolant AN INSPIRED DESIGN TO MEET YOUR NEEDS
 JP1500

AN INSPIRED DESIGN TO MEET YOUR NEEDS

STANDARD SPECIFICATIONS
6. FUEL SYSTEM
On Generating Sets up to 700 KVA, the baseframe
design is incorporated with an integral fuel tank with
a capacity of approx. 8 hours running at Full Load.
The tank is supplied complete with fill cap breather,
fuel feed and return lines to the Engine and drain
plug.

7. ALTERNATOR
7.1 INSULATION SYSTEM
• The insulation system is Class H.
• All windings are impregnated in either a triple dip
thermosetting liquid, oil and acid resisting polyester
varnish or vacuum pressure impregnated with a
special polyester resin.
• Heavy coat of antitracking varnish additional
protection against moisture or condensation.

7.2 AUTOMATIC VOLTAGE REGULATOR (AVR)

The fully sealed Automatic Voltage Regulator
maintains the Voltage Regulation at ±0.5%. Nominal
adjustment by means of a trim pot incorporated on
the AVR.

7.3 MOTOR STARTING

Generating Set pictured may include optional accessories An overload capacity equivalent to 300% of the Full
Load impedance at zero Power Factor can be
sustained for 10 seconds.
RATINGS DEFINITION
8. MOUNTING ARRANGEMENT
Prime Power 8.1 BASE FRAME
These ratings are applicable for supplying continuous electrical power (at variable load) in lieu of The complete Generating Set is mounted as a whole
commercially purchased power. 10% overload power is available for 1 hour in 12 hours continuous on a heavy duty fabricated steel Baseframe.
operation.
8.2 COUPLING
Standby Power The Engine and Alternator are directly coupled by
These ratings are applicable for supplying continuous electrical power (at variable load) in the event of a means of an SAE flange. The Engine flywheel is
utility power failure. No overload is permitted on these ratings. flexibly coupled to the Alternator rotor.

8.3 ANTI-VIBRATION MOUNTING PADS

STANDARD REFERENCE CONDITIONS Anti-Vibration pads are affixed between the Engine /
Alternator feet and the Baseframe thus ensuring
Output ratings are presented at 25°C air inlet temperature, barometric pressure 100 kPa, relative humidity complete vibration isolation of the rotating assembly.
30%. This generating set is designed to operate at high ambient temperatures (up to 55°C), humidity (up to
99%) and higher altitudes. De-ration may apply, please consult your dealer for specific site ratings. 8.4 SAFETY GUARDS
The Fan & Fan Drive along with the Battery Charging
Some of the specifications are not standard on all Genset models. Alternator are Safety Guard protected for personnel
protection.
AVAILABLE OPTIONS & ACCESSORIES
9. FACTORY TESTS
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs. • The Generating set is load tested before dispatch
• All protective devices control functions and site
OPTIONS ACCESSORIES load conditions are simulated. The generator and it’s
• A variety of generating set control and synchronizing panels • Genuine spare parts systems are checked before dispatch.
• Additional protection alarms and shutdowns • Load banks
10. EQUIPMENT FINISHING
• Water fuel seperator • Auxiliary fuel tanks All mild steel components are fully degreased and
• Water jacket heater • Manual & automatic transfer painted with powder coated paint to ensure
maximum scuff resistance and durability.
• Battery charger switches
11. DOCUMENTATIONS
Operation & Maintenance manual, Circuit wiring
diagrams and Commissioning / Fault Finding instruction
leaflets are accompanied with the Generator.
Distributed and Serviced by:
12. QUALITY STANDARDS
The equipment meets the following standards:
BS4999, BS5000, BS5514 IEC 60034, VDE0530,
NEMA MG 1.22 and ISO 8528.

13. WARRANTY
For further information on all of the standard and optional features accompanying this product please
All of the Generating Sets are covered under a
contact your local dealer or visit www.taklairaq.com warranty policy for a period of 12 months. Warranty
of the equipment is in line with manufacturers
warranty terms & conditions.
(check warranty statement for more details, as it may vary for different countries)
JET Generators are assembled All information in this document is substantially correct
in facilities certified to ISO 9001 at time of printing and may be altered subsequently.
In line with continuous product development, we reserve the
ISO 9001: 2008
right to change specifications without notice.
FM 56710
2023