AAN-100
Alarm Access Network Interface Module
The AAN-100 module provides the next generation of advanced technology for integrated access control, alarm
monitoring and other security features. Advanced technology such as Flash Memory (eliminating ROMs/
EPROMs) for firmware storage and updates, direct interface to various networks (LANs), up to 6 plug-in
communication modules, up to 1.300,000 cardholders with plug-in RAM modules, and up to 100 devices such
as badge readers, alarm panels and status panels.
AAN-100 Standard Features:
Download of firmware into 2 megabits of flash
memory
Plug-in communications and memory modules
Supports direct network interface/redundant LANs
TCP/IP protocol
Supports RS-232/RS-485/Fiber optics interfaces
Up to 6 communications ports/Dual path to host
1 MB RAM (AME-10) standard, expandable to 8
MBytes
Stores up to 250,000 cardholders/100,000 Events
Battery back-up of database and events
Dedicated/dial communications interface to host
Grade AA communications to host/Local printout
Elevator control/Anti-passback/Alarm masking
Directly controls 96 card readers
Supports up to 32 alarm panels (1280 zones)
LAN
RS-232
Modem
TYPICAL DEVICES ON RS-485 LINE
Dial back up
ASI-1
AAN-100
ASM-48
P1
APOLLO
80 APA/APD
P2
ASM-48
ANI-1
96 Readers
1280 Alarm Zones
P3
ASM-48
1280 Relay Outputs
ASM-48
1,300,000 Cardholders
CLR
ENT
AP-520
APOLLO
APOLLO
APA-15
ENTER BADGE
24/12 TUESDAY
APOLLO AP 500
TEMPERATURE 50C
4
7
5
8
0
CLEAR
3
6
9
CMD
ARM-16
ENTER
AP-500
AP-501
ON LINE
ON LINE
ON LINE
ON LINE
P4
ASA 72
HOST
ACK
TEST
ASA-72
Single Network Configuration ( LAN )
RS-485
TO OTHER DEVICES
APIs
APACS
HID
HID
LAN
5
8
3610 Birch Street
Newport Beach, California 92660-2619 USA
Phone 949-852-8178 FAX 949-852-8172
http://www.apollo-security.com
E-mail: apollo@netbox.com
OPERATION
The AAN-100 communicates with APOLLO intelligent mag stripe readers, and with Wiegand, proximity and
other card reader technologies through the AIM-4 and API interface modules. The AAN-100 also communicates
with various APOLLO alarm panels and status panels. All access decisions are made in the AAN-100 using an
advanced technology 32-bit processor. The AAN-100 can interface directly to existing networks, thus saving
cost and time of installation.
The AAN-100 controller comes with 1 MB RAM as standard. You can expand the RAM using AME-10 or
AME-20 plug-in RAM modules. The AAN-100 requires 1 to 4 device driver modules (ASM-23 or ASM-48)
depending upon how many lines are to be used to communicate with the card reader, alarm modules or status
panels. In the network configuration the AAN-100 requires either a single or dual Ethernet module ANI-1
(single or dual networks). For non-network configuration, the dual port high-speed serial interface module
(ASI-1) will be required. If the dual port high-speed interface is selected then you must add a single or dual RS232 or RS-485 driver module (ASM-23 or ASM-48) for communications to the host.
ORDERING INFORMATION
Mode l
Numbe r
Part Numbe r
AAN-100
430-100
Alarm/Access network controller. Includes one AME-01
ANI-1
430-110
Network interface, Ethernet (10BASE-T and AUI)
ASI-1
430-130
High-speed serial host interface, dual RS-232/485 (Uses ASM-23 or ASM-48)
ASM-23
430-131
Plug-in host or device RS-232 driver
ASM-48
430-132
Plug-in host or device RS-485 driver
AME-10
430-150
1 Mbyte RAM expansion
AME-20
430-160
2 MByte RAM expansion consult factory for expansion to 8MB
APU-24R
460-150
230/115 VAC input, 24 Vdc 2.0A output, regulated uninterruptible power supply/battery
charger in enclosure with lock, power switch, fuse and tamper switch. Includes one battery
tray. AAN-100 mounts inside.
AUS-12
460-070
115 VAC input, 12 Vdc 2.0A output, regulated uninterruptible power supply, 5 Ah battery,
enclosure, power indicator, fuse and tamper switch. AAN-100 mounts inside.
AUS-12I
460-071
230 VAC input, 12 Vdc 2.0A output, regulated uninterruptible power supply, 5 Ah battery,
enclosure, power indicator, fuse and tamper switch. AAN-100 mounts inside.
ABT-12
460-050
Single battery pack, 12Ah.
ABT-24
460-160
Dual battery pack, 12Ah each.
ATM-48
470-030
Terminator for RS-485 (2 per line required)
De scription
SPECIFICATIONS
Dimensions:
Operating Temperature Range:
Humidity Range:
Power Requirements:
7.5H x 5.5W x 1D (19 x 14 x 2.5 cm)
0 to 50 C (32 to +122 F)
0 to 95%, non-condensing
13.6 to 28 Vdc @ 750 mA (max.)
Note: Information contained in this document is subject to change without notice.
3610 Birch Street
Newport Beach, California 92660-2619 USA
Phone 949-852-8178 FAX 949-852-8172
http://www.apollo-security.com
E-mail: apollo@netbox.com
