var ws281x = require('rpi-ws281x');

// One time initialization, assumes an 8 pixel strip
ws281x.configure({ leds: 8 });

// Create my pixels
var pixels = new Uint32Array(8);

// Set first three pixels to red, green and blue
// Colors are packed as 0xWWRRGGBB or 0x00RRGGBB (if RGB only)

pixels[0] = 0x00FF0000;
pixels[1] = 0x0000FF00;
pixels[2] = 0x000000FF;

// Render pixels to the Neopixel strip
ws281x.render(pixels);

var ws281x = require('rpi-ws281x');

class Example {
    constructor() {
        this.config = {};

        // Number of leds in my strip
        this.config.leds = 169;

        // Use DMA 10 (default 10)
        this.config.dma = 10;

        // Set full brightness, a value from 0 to 255 (default 255)
        this.config.brightness = 255;

        // Set the GPIO number to communicate with the Neopixel strip (default 18)
        this.config.gpio = 18;

        // Specify RGB sequence
        this.config.stripType = 'grb';

        // Set gamma correction to 2.2 
        this.config.gamma = 2.2;

        // Configure ws281x
        ws281x.configure(this.config);
    }

    run() {
        // Create a pixel array matching the number of leds.
        // This must be an instance of Uint32Array.
        let pixels = new Uint32Array(this.config.leds);
        let leds = this.config.leds;

        // Set pixels to a gradient from black to red
        for (let i = 0; i < leds; i++) {
            let red = (i / leds) * 255;
            let green = 0;
            let blue = 0;
            let color = (red << 16) | (green << 8) | blue;
            pixels[i] = color;
        }
        // Render to strip
        ws281x.render(pixels);
    }
}

var example = new Example();
example.run();

var ws281x = require('rpi-ws281x');

class Example {

    constructor() {
        // Current pixel position
        this.offset = 0;

        // Set my Neopixel configuration
        this.config = {leds:169, stripType : 'grb', gpio:18};

        // Configure ws281x
        ws281x.configure(this.config);
    }

    loop() {
        var pixels = new Uint32Array(this.config.leds);

        // Set a specific pixel
        pixels[this.offset] = 0xFF0000;

        // Move on to next
        this.offset = (this.offset + 1) % this.config.leds;

        // Render to strip
        ws281x.render(pixels);
    }

    run() {
        // Loop every 100 ms
        setInterval(this.loop.bind(this), 100);
    }
};

var example = new Example();
example.run();

var ws281x = require('rpi-ws281x');

class Example {

    constructor() {
        // Current pixel position
        this.offset = 0;

        // Set my Neopixel configuration
        // By setting width and height instead of number of leds
        // you may use named pixel mappings.
        // Serpentine is a common mapping for matrices.
        this.config = { width: 13, height: 13, stripType: 'grb', gpio: 18, dma: 10, map: 'serpentine' };

        // Configure ws281x
        ws281x.configure(this.config);
    }

    loop() {
        var leds = this.config.width * this.config.height;
        var pixels = new Uint32Array(leds);

        // Set a specific pixel
        pixels[this.offset] = 0xFFFFFF;

        // Move on to next
        this.offset = (this.offset + 1) % leds;

        // Render to strip
        ws281x.render(pixels);
    }

    run() {
        // Loop every 50 ms
        setInterval(this.loop.bind(this), 50);
    }
};

var example = new Example();
example.run();