QPRO ALARMS
Alarm Alarm type Cause Attention
Yarn threading error
A1 Yarn Threading Error (system) Mechanical/Electrical
Yarn break occurred right after drum start
A2 Yarn Threading Error (AD) AD error Mechanical Attention
A3 Take-up Tube Supply Error Take-up tube not ready Operator
A4 Rear Package Not Processed Doffing operation not possible due to package at rear Operator
b0 Bobbin Supply Error No bobbin supplied Operator
b1 Lower Yarn Pickup Error Lower yarn pickup error Mechanical/Electrical
b3 Start Up Cut Alarm Clearer cut occurs frequently Quality
b5 Yarn Count Alarm (UQC) - Quality
b6 Pearl Chain Alarm (UQC) - Quality
b7 Moire Alarm (UQC) - Quality
b8 CV Alarm (UQC) - Quality
b9 Foreign Fiber Alarm (UQC) - Quality
bA Hairiness Alarm (UQC) - Quality
bb IPI Alarm (UQC) - Quality
bC CMT Alarm (UQC) - Quality
bd YF Alarm (UQC) - Quality
bE MFAlarm (UQC) - Quality
bF Other alarms - Quality/Mech/Elect
bG PPAlarm (UQC) - Quality
C0 Clearer Zero Adjustment Alarm Clearer zero adjusting error operator/Electrical
C1 Clearer Slot Jammed Alarm Yarn waste clog in clearer slot operator/Electrical
C2 Insufficient Cut Alarm Clearer did not cut sufficiently Quality/Electrical
C3 Clearer Technical Alarm Clearer technical alarm occurred Electrical
d1 Drum Wrapping Alarm Drum wrapping occurred Operator/Mech/Elect
E1 Splicer Home Position Sensor Alarm Splicer operation error Mech/Elect
Bal-Con Sensor Alarm
E3 Bobbin (package) detection sensor error Operator/Mech/Elect
E6 Package Rotating Sensor Alarm Package rotating sensor error electrical/mech
Retie pipe operation error
E7 Retie Pipe Home Position Sensor Alarm Mech/Elect
Retie pipe home position sensor error
E8 PLC21 Alarm PLC21 yarn travel detection error Mech/Elect
E9 Lower Yarn Sensor Alarm Lower yarn sensor error Operator/Mech/Elect
PC sensor error
EA PC Sensor Alarm Mech/Elect
Tension error detected
Tensor opener operation error
EF Tensor Operation Check Sensor Alarm Mech/Elect
Tensor operation check sensor error
Shutter mouth operation error
EG Suction Mouth Angle Sensor Alarm Mech/Elect
Suction mouth angle sensor error
Shutter operation error
EH Shutter Home Position Sensor Alarm Mech/Elect
Shutter home position sensor error
Bal-Con operation error
EJ Bal-Con Home Position Sensor Alarm Mech/Elect
Bal-Con home position sensor error
Peg operation error
Peg Home Position Sensor Alarm Peg home position sensor error
EL Mech/Elect
Tray Eject Home Position Sensor Alarm Tray eject operation error
Tray eject home position sensor error
Magazine can operation error
En Magazine Can Position Sensor Alarm Mech/Elect
Magazine can home position sensor error
Yarn guide lever operation error
Eo Yarn Guide Lever Home Position sensor Alarm Operator/Mech/Elect
Yarn guide lever home position sensor error
n1 Bal-Con Down Alarm Bobbin detection sensor is left ON after drum start Operator/Mech/Elect
n2 Bal-Con Up Alarm Bal-Con up error Mech/Elect
o1 Unconsumed Wax Alarm Wax application failure Operator/Quality/Mech/Elect
o2 No Wax Alarm No wax Operator
P1 Upper Yarn End Find Error - Operator/Mech
Double yarn detected during upper yarn end
P2 Upper Double Yarn Alarm Operator/Quality/Mech
find operation
P3 Sizing Alarm Package diameter exceeds the specified value Operator
P4 Package Brake Error Package does not stop within specified time Mech/Quality/Elect
P5 PJC Alarm (upper limit) Too many yarn breaks/packages Quality/Mech/Elect
P6 PJC Alarm (lower limit) Too few yarn breaks/packages Quality/Electrical
P7 Package Half-locked Alarm Bad package rotation occurred Opeartor/Mech
S1 Mis-splicing - Operator/Mech
S2 Splicer Cut - Operator/Mech/Quality
T1 Tension Break Alarm Frequent breaks in tension Mech/Quality/Elect
T3 Tension Error (LOW) Tension error (LOW) detected Mech/Elect
T4 Tension Error (HIGH) Tension error (HIGH) detected Mech/Elect
u1 DC5V Power Supply Error Line voltage error detected on DC5V power supply Electrical
u2 DC15V Power Supply Error Line voltage error detected on DC15V power supply Electrical
u3 DC24V Power Supply Error Line voltage error detected on DC24V power supply Electrical
