J-1175
J-1175 Dual Power
Jaw Crusher
SPECIFICATION:
Inlet Opening: 1070mm x 760mm (42” x 30”)
Net Engine Power: Tier 2 / Stage II Equivalent: Scania DC9 350hp (257kW)
Tier 4F / Stage IV: Scania DC9 350hp (257kW)
Portability: Tracked
Operating Weight: 54,300kg (119,711lbs)
(without by-pass conveyor and magnet options)
56,500kg (124,561lbs)
(with by-pass conveyor and magnet options) TM
19
SPECIFICATION
HOPPER / FEEDER
Hopper capacity: 9m³ (11.7yd³)
Feed height VGF: 3.98m (12' 11")
Feed height Prescreen: 4.12m (13’ 6”)
Material: 12mm (1/2”) wear resistant steel
Feed width at rear VGF: 2.67m (8’ 9”)
Feed width at rear Prescreen: 2.65m (8’ 8”)
Locking mechanism: manual
Hydraulically folding sides and rear
Vibrating Grizzly feeder (VGF): 1.05m wide x 4.25m long Hopper & Feeder
VGF grizzly aperture: 75mm (Options 50mm/100mm/125mm)
VGF wire mesh aperture: 38mm (Other options available upon request)
VGF Speed range: variable, 450-850 rpm
Pan Feeder Speed range: variable, 450-850 rpm
Optional Hopper extensions - 11m³ (14.4yd³)
JAW CHAMBER
Terex JW42 Chamber single toggle jaw crusher
Inlet width: 1070mm (42”)
Inlet gape: 760mm (30”)
Under jaw clearance: 460mm nominal
Drive arrangement: Electric
Maximum Closed Side settings: 145mm (5¾”) (subject to toggle Jaw Chamber
selection)
Minimum Closed Side Settings (CSS): 45mm (1 3/4”) Demolition
and Recycle applications. 75mm (3”) ‘Hard-Rock’ Quarry application,
60mm (2 1/2”) ‘Soft-Rock’ Quarry application
Reverse action for clearing blockages
Full hydraulic closed side setting adjust
Standard Liner Profile: S-Tooth (18% Manganese)
MAIN CONVEYOR
Belt Width: 1.0m (40”)
Belt Spec: Plain
Main Conveyor
Working Angle: 22°
Speed: 100 m/min nominal
Discharge Height: 3.6m (11’ 10”) with standard conveyor
Optional extended conveyor discharge height: 4m (13’ 2”),
incorporates folding head section for transport
Hydraulic raise/lower of head section for service access
Impact bars and wear resistant liners at feed point
High spec scraper at head drum
Main Conveyor
20
J-1175
MAIN CONVEYOR continued
Tail section raises hydraulically to increase clearance when tracking
Dust suppression: fitted with hose and spraybars as standard (no
pump supplied)
Stockpile capacity: 69.4m3 (90.8yd3) @ 40°
POWERPACK
Tier 2 / Stage II Equivalent: Scania DC9 350hp (257kW)
Tier 4F / Stage IV: Scania DC9 350hp (257kW
Engine Speed: 1500 rpm
TANK CAPACITIES
Hydraulic Tank: 390 litres / 85 UK gal / 103 US gal
Fuel Tank: 430 litres / 95 UK gal / 114 US gal
Urea Tank: 60 litres / 13.2 UK gal / 16 US gal Tier 2 / Stage II Equivalent: Scania DC9 350hp (257kW)
BY-PASS CONVEYOR (OPTIONAL)
Belt Width: 650mm (26”)
Belt Spec: Plain
Working Angle: 22°
Hydraullically folds for transport
Standard Discharge Height: 2.1m (7’)
Stockpile capacity: 13.8m3 (18yd3) @ 40°
Optional extended discharge height: 2.9m (9’ 6”)
Extended Stockpile capacity: 36.3m3 (47.5yd3) @ 40°
UNDERCARRIAGE Bypass Conveyor (Optional)
Bolt on tracks
Shoe Width: 500mm (20”)
Sprocket Centres: 3.78m (12’ 5”)
Two Speed Tracking with ‘soft start’
Speed: 1.1 km/h (Maximum Speed)
Gradeability: 25°
TOOL BOX
Mounted lockable toolbox
Tool Kit and flogging spanners
Grease gun Tool Box
Manuals
TM
21
CHUTES
Heavy duty inlet chute with bolt-up construction, and liner plates
By-pass chute with selectable discharge flop gate, to either by-pass
conveyor or main conveyor
CONTROL SYSTEM
Advanced CANBUS compliant system Large display screen (IP65
Rated) Four simple operating modes with menu driven graphic user
interface-
- Track mode: For moving machine
- Automatic mode: For automatically starting the machine in prede-
termined sequence Control System
- Set-up mode: For folding/setting up machine
- Configuration mode: For testing/setting individual components
Choice of preset parameters to suit crushing applications
- Hard Rock
- Soft Rock
- Demolition and Recycle
User friendly incremental selection of feeder and crusher speed
enable the operator to achieve the optimal throughput Detachable
Umbilical control for tracking Radio remote control (optional) Inte-
grated machine and engine control panel Lockable compartment Auto
regulating feeder selectable for improved throughput control
Magnet Separator
MAGNETIC SEPARATOR (OPTIONAL)
Suspended self cleaning crossbelt overband magnet
Belt Width: 750mm (30”)
Belt Spec: Cleated
PLATFORMS
Catwalk access on both sides of the machine with access to both
sides of the powerunit
Compact folding for transport
REMOTE CONTROL UNIT (OPTIONAL)
Full function radio remote unit
Machine can be switched from crushing mode into track mode,
moved and switched back to operating mode from remote control unit
Feeder stop / start
ELECTRICAL SPECIFACTION
Main Conveyor: 2 x 5.5 kW Motors
Magnet: 1.5 kW Motors
By-Pass Conveyor: 4 kW Motor
Hydraulic Pump: 55 kW ( Tracking, Pre-Screen, Feeder, Folding)
Crusher Motor: 110 kW controlled via VSD (Variable Speed Drive)
(Speed Control, Ability to run in Reverse, Unblock Feature)
22
J-1175
STANDARD FEATURES
ENGINE: OPTIONAL EQUIPMENT
Tier 2 / Stage II Equivalent: Scania DC9 350hp (257kW) water Radio remote System: Operational controls of machine (auto start/
cooled diesel engine stop) & track movement
Tier 4F / Stage IV: Scania DC9 350hp (257kW) water cooled diesel Bypass conveyor with 650mm wide plain belt
engine Extended bypass conveyor with 650mm wide plain belt
JAW CHAMBER: Singlepole over band magnet c/w stainless steel skirting & stainless
Terex 1070mm x 762mm (42” x 30”) single toggle jaw crusher steel discharge chute
Electric drive and advanced electronic control system Twinpole overband magnet (skirting & chute as above)
Fully hydraulically adjustable closed side setting Belt weigher
Reversible operation for clearing blockages Special paint colour (if different from Terex White Colour RAL 1013 or
S tooth liners Standard - 18% Manganese as standard Finlay Orange RAL 2002) . RAL must be specified on order
Optional spacing on grizzly for integrated pan and feeder:
HOPPER/FEEDER:
50mm/100mm/125mm - please specify below
Hopper capacity: 9m³ (11.7 yd³)
Hydraulically driven water pump (Requires 1 aux drive)
Hydraulically folding hopper sides Re-bar deflector plate - fits underneath jaw
Heavy duty vibrating feeder Independent pre-screen c/w extended bypass conveyor with
Integrated pan and feeder - cassette is 75mm spacing as standard 650mm wide plain belt, 75mm cassette spacing and 38mm mesh as
Selectable discharge to by-pass conveyor or main conveyor standard - other cassette and mesh apertures available upon request
Mesh aperture on grizzly feeder: 38mm (1.5”) (Requires 1 aux drive)
Dust cover on discharge conveyor
MAIN CONVEYOR:
Rip stop belt option
1m wide main belt fitted with impact bars at feed point
Lighting mast
High spec scraper at head drum
Cold climate lubrication kit (for below -10ºc ambient)
Piped for dust supression complete with spraybars
Hot climate lubrication kit (For above +30ºc ambient)
Separate central operators panel
Toggle options: 570mm for larger closed side setting
GENERAL: 610mm to maintain minimum recommended
Piped for overband magnet closed side setting
Standard toggle setting 590mm Extended Hopper Flares (11m³ Capacity) - 14.4yd³
Galvanised catwalk c/w handrail, kick board and access ladders Portable urea filling pump c/w nozzle (Tier 4 models only)
Heavy duty undercarriage unit with 500mm wide pads ** S tooth liners standard
Hand held track control set with connection lead
Two speed tracks with ‘soft start’
Safety guards in compliance with machinery directive
Emergency stops
TM
23
24
Hopper / Feeder
u Hopper capacity: 9m³ (11.7yd³) Electrical Specification
u Feed height VGF: 3.98m (12’ 11”) Jaw Chamber u Main Conveyor: 2 x 5.5 kW Motors
u Feed height Prescreen: 4.12m (13’ 6”) u Terex JW42 Chamber single toggle jaw crusher u Magnet: 1.5kW Motors
u Material: 12mm (1/2”) wear resistant steel u Inlet width: 1070mm (42”) u By-Pass Conveyor: 4 kW Motors
u Feed width at rear VGF: 2.67m (8’ 9”) u Inlet gap: 760mm (30”) u Hydraulic Pump: 55 kW
u Feed width at rear Prescreen: 2.65m (8’ 8”) u Under jaw clearance: 460mm nominal
(Tracking, Pre-Screen, Feeder, Folding)
u Locking mechanism: manual u Drive arrangement: Hydrostatic
u Hydraulically folding sides and rear u Crusher Motor: 110 kW controlled via VSD
u Maximum Closed Side settings: 145mm (5¾”) (subject to toggle selection)
u Vibrating Grizzly feeder (VGF): 1.05m wide x 4.25m long u Minimum Closed Side Settings (CSS): 45mm (1 3/4”) Demolition and Recycle applications. 75mm (3”) (Variable Speed Drive)
u VGF grizzly aperture: 75mm (Options 50mm/100mm/125mm) ‘Hard-Rock’ Quarry application, 60mm (2 1/2”) ‘Soft-Rock’ Quarry application (Speed Control, Ability to run in Reverse, Unblock Feature)
u VGF wire mesh aperture: 38mm u Reverse action for clearing blockages
(Other options available upon request) u Full hydraulic closed side setting adjust Magnet
u VGF Speed range: variable, 450-850 rpm u Standard Liner Profile: S-Tooth (18% Manganese) u Optional
u Pan Feeder Speed range: variable, 450-850 rpm
u Optional Hopper extensions - 11m³ (14.4yd³)
Main Conveyor
u Belt Width: 1m (40”)
u Belt Spec: Plain
Chassis u Working Angle: 22°
u Robust, heavy
u Speed: 100 m/min nominal
duty chassis
u Discharge Height: 3.6m (11’ 10”) with standard conveyor
u Optional extended conveyor discharge height: 4m
(13’ 2”), incorporates folding head section for transport
Platforms u Hydraulic raise/lower of head section for service access
u Catwalk access on both sides of the u Impact bars and wear resistant liners at feed point
machine with access to both sides of the u High spec scraper at head drum
powerunit u Tail section raises hydraulically to increase clearance
u Compact folding for transport when tracking
u Dust suppression: fitted with hose and spraybars as
standard (no pump supplied)
u Stockpile capacity: 69.4m3 (90.8yd3) @ 40°
By-pass conveyor (optional)
u Belt Width: 650mm (26”)
Powerpack u Belt Spec: Plain
u Tier 2 / Stage II Equivalent: Scania DC9 350hp (257kW) u Working Angle: 22°
Engine Power: 350hp (261 kW) Undercarriage u Hydraulically folds for transport
Engine Speed: 1500 rpm u Bolt on tracks u Standard Discharge Height: 2.1m (7’)
u Shoe Width: 500mm (20”) u Stockpile capacity: 13.8m3 (18yd3) @ 40°
u Sprocket Centres: 3.78m (12’ 5”) u Optional extended discharge height: 2.9m (9’ 6”)
u Tier 4F / Stage IV: Scania DC9 77A
u Two Speed Tracking with ‘soft start’: u Extended Stockpile capacity: 36.3m3 (47.5yd3) @ 40°
Engine Power: 350hp (257 kW) (EU SPEC)
u Speed: 1.1 km/h (Maximum Speed)
Engine Speed: 1500 rpm
u Gradeability: 25°
J-1175
Transport Dimensions
14.5m (47’ 8”) 2.9m (9’ 6” )
3.5m (11’ 6”)
Working Dimensions
15.7m (51’ 8”) 6.2m (20’ 4”)
3.95m (12’ 1”)
MACHINE WEIGHT: 54,300kg (119,711lbs)
Operating weight (without by-pass conveyor and magnet options)
56,500kg (124 ,561lbs)
Operating weight (with by-pass conveyor and magnet options)
TM
25
26
