10W Single Output Switching Power Supply S- 10 series

■ Features :
· Universal AC input/Full range
· Protections:Short circuit/Over load/Over voltage/Over temperature
· Cooling by free air convection
· 100% full load burn-in test
· Fixed switching frequency at 67KHz
· 1 year warranty

SPECIFICATION
MODEL S-10-5 S-10-12 S-10-24
DC VOLTAGE 5V 12V 24V
RATED CURRENT 2A 0.83A 0.41A
CURRENT RANGE 0 ~ 2A 0 ~0.83A 0 ~ 0.41A
RATED POWER 10W 10W 10W
RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 200mVp-p
OUTPUT VOLTAGE ADJ. RANGE 4.75 ~ 5.5V 10.8 ~ 13.2V 22.6 ~ 26.4V
VOLTAGE TOLERANCE Note.3 ±2.0% ±1.0% ±1.0%
LINE REGULATION ±1.5% ±0.5% ±0.5%
LOAD REGULATION ±1.5% ±0.5% ±0.5%
SETUP, RISE 1000ms, 30ms/230VAC 1000ms, 30ms/115VAC at full load
HOLD TIME (Typ.) 100ms/230VAC 20ms/115VAC at full load
VOLTAGE RANGE 85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE 47 ~ 63Hz
EFFICIENCY (Typ.) 78% 81% 84%
INPUT
AC CURRENT 0.35A/115VAC 0.25A/230VAC
INRUSH CURRENT (max.) COLD START 20A
LEAKAGE CURRENT <2mA / 240VAC
Above 105% rated output power
OVER LOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed

PROTECTION OVER VOLTAGE

Protection type : Shut down o/p voltage, re-power on to recover
U1 Tj 140℃ typically (U1) Detect on main control IC
OVER TEMPERATURE
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
WORKING TEMP. -20 ~ +60 ℃(Refer to output load derating curve)
WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85℃ , 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/ ℃(0 ~ 50℃ )
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS UL60950-1, CB(IEC60950-1) Approved
WITHSTAND VOLTAGE I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
EMC
(Note 6) EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B
HARMONIC CURRENT Compliance to EN61000-3-2,-3
EMS IMMUNITY Compliance to EN61000-4-2, 3, 4, 5, 6, 8,11, ENV50204, EN55024, EN61000-6-1 Light industry level, criteria A
MTBF 390Khrs min. MIL-HDBK-217F (25℃ )
OTHERS DIMENSION 70*40*30mm (L*W*H)
PACKING

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

NOTE
4. Line regulation is measured from low line to high line at rated load.

5. Load regulation is measured from 0% to 100% rated load.

6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.