INTRODUCING HEAT TECHNOLOGY

PACE ST SYSTEMS TIP HEATER CARTRIDGE & SENSATEMP TECHNOLOGY

IN TODAY’S ENVIRONMENT Upgrade your equipment, clear off your work bench and unlock TIP-HEATER CARTRIDGE TECHNOLOGY The key advantage of Tip-Heater Cartridge based technology is that its advanced
your success with INTELLIHEATTM! electronics provide instantaneous load sensing and on-demand power to quickly reflow solder joints, regardless of the mass of the application.
FLEXIBILITY ISN’T JUST Further, the position of the control sensor is as far forward as possible to immediately respond to the thermal demand of the work. The tip and
IMPORTANT, IT’S THE KEY With over 50 years of experience and industry leadership in heater are permanently coupled, ensuring all the heat generated by the heater is available for use by the tip. For applications where the work
rework and repair technology and techniques, PACE provides
TO SUCCESS... much more than simply equipment. When you purchase PACE
cycle is high and for micro-miniature applications the direct power approach is ideal as the thermal demand is continuously monitored and the
heater responds immediately by providing adequate power to meet the demand from the work, without overshoot.
products, you receive access to one of the most valuable resources
Component foot-prints are shrinking, through-put requirements are in the industry; PACE’s applications and technical support services.
increasing, and thermally massive power management components Over the years, our applications support services have been the
(connectors, heat sinks, RF shields, and SMDs) on heavy ground cornerstone of quality assurance and repair reliability for countless Control Sensor Position Heater “Printed” on Ceramic Heater - Standard resistance
planes are not going away anytime soon. Oh yes, let’s not forget customers. Whenever you encounter a new component, a new PCB, Relative to Tip
Poor Position, Heating Element, (40-60 W)
about the challenges of incorporating Lead Free solders into your Lead Free Solder, or if you just want reassurance that your process Inefficient

process! Being locked into one heat control technology on your is safe and effective, simply contact PACE and we will create a Curie-Point Heating Systems - High frequency emission
creating heat in ferromagnetic slug using its Curiepoint
Soldering/Desoldering system isn’t going to open the door to your procedure for you that not only identifies the equipment required to to control temperature (30-40 W)
success... do the job correctly, but also every step in the process!
For efficient heating, accurate Fair Position,
Fairly Efficient
The ability to have multiple heating technologies available within control and for forming the
a single system directly affects your bottom line. Until now, most best solder joint, use an iron PACE SensaTemp Precision Control System. High
TABLE OF CONTENTS mass resevoir heater with platinum RTD sensor.
systems only offer one type of heating technology which will never with the shortest sensor (52 W)
fit every application efficiently. The time has come for soldering
PAGE
pathway!
and desoldering systems to evolve.
Good Position,
2 INTRODUCTION & TABLE OF CONTENTS Efficient

3 PACE HEATING TECHNOLOGY PACE Tip Heater Cartridge System - High thermo
delivery, Sensor controlled ceramic heater/tip cartridge
4 INTELLIHEAT COMPATIBLE HANDPIECES (62 W)

6 HANDPIECE AND POWER SOURCE CHARTS

7 ST 30, ST 50 AND ST 70 SYSTEMS
Best Position, Highly Efficient
8 ST 100 SYSTEM

....FLEXIBILITY DRIVES THROUGH-PUT! 9 INSTANT SETBACK CUBBY & LEAD FREE ACCESSORIES
10 ST 65, ST 75 AND ST 115 POWER SUPPLIES
PACE is proud to introduce your key to future success...The 11 ST SYSTEMS SPECIFICATIONS
MAINTAINING PERFORMANCE IN THE SENSATEMP ® TECHNOLOGY At the heart of SensaTemp
INTELLIHEATTM Control System. IntelliHeat is the only thermal control 12 MBT 301 is a laser trimmed, platinum RTD sensor that is more than 5 times
system capable of managing multiple types of heating technologies
“GREEN” ZONE IS MORE LIKELY AS
13 MBT 350 more accurate than conventional thermo-couples. This level of
within a single Power Source. There is no longer a need to have SENSOR PATHWAY BECOMES SMALLER
accuracy allows for safe, productive soldering at the lowest possible
multiple Power Sources on your work bench or to force operators 14 ST 25, MBT 250 AND PRC 2000
temperatures. As a result, the amount of time spent reflowing each
to use only one heating technology. Simply plug in any compatible 15 LEAD FREE SOLDERING joint is reduced, minimizing the possibility of damage. Additionally,
handpiece and IntelliHeat does the rest. 16 SOLDERING WITH NITROGEN IDEAL IRON PERFOMANCE SensaTemp allows you to change tips, heaters and handpieces at
17 NITROGEN ASSISTED SOLDERING ACCESSORIES
will, without ever having to re-calibrate! SensaTemp’s unique heater
The IntelliHeat Control System allows either SENSATEMP® or Tip- Tip Temperature Solder Joint Temperature design acts as a thermal dampener that minimizes tip temperature
Heater Cartridge based technology handpieces to be plugged into 18 TD-100 STANDARD TIPS overshoot, ensures temperature stability and creates a “thermal
a single Power Source. Finally, the benefits of SENSATEMP® and 20 TD-100 DIAMOND SERIES TIPS 350 C
O
reservoir” that can be accessed instantaneously when high mass
Tip-Heater Cartridge based technology can be found in a single applications are being performed.
21 TD-100 SMT REMOVAL TIPS Too Hot
system, without restriction.
22 MT-100 & TP-100 SMT REMOVAL TIPS
SensaTemp delivers consistent, repeatable results regardless of the
PACE’s legendary SENSATEMP® technology is renowned for its 23 PS-90 SOLDERING TIPS 200 C
O Ideal Process thermal demand of the work. Its ability to respond quickly is ideal
temperature stability and ability to handle high mass applications. 24 PS-90 SMT REMOVAL TIPS
Control
for light work, while its amazing thermal capacity can meet the
Window
For smaller components and when through-put is important, there challenges of the heaviest thermal loads, providing the operator with
25 SX-90 DESOLDERING/SOLDER REMOVAL TIPS
is Tip-Heater Cartridge based technology. Tip-Heater Cartridge the flexibility that is essential in today’s ever changing environment.
based technology is a patented technology that boasts the best 26 TT-65 SMT TIPS AND TJ-85 NOZZLES Too Cold
0 C
O Regardless of your application, SensaTemp delivers unsurpassed
response time for high volume applications and easily keeps up in 27 PRODUCT PAGE thermal performance, productivity and “bottom line” savings.
Workflow Increasing
a fast paced environment.

2 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 3
 INTELLIHEAT COMPATIBLE HANDPIECES INTELLIHEAT COMPATIBLE HANDPIECES
TIP-HEATER CARTRIDGE HANDPIECES PERFECT FOR LEAD FREE VERSATILITY, PERFORMANCE AND VALUE SENSATEMP HANDPIECES

TD-100 THERMO-DRIVE ® SOLDERING IRON PS-90 UNIVERSAL SOLDERING IRON

The TD-100 Thermo-Drive® Soldering Iron is the only iron The Universal Soldering Iron (PS-90) is ideal for most soldering
crafted by a team of surgical instrument engineers and is applications and SMT rework operations where high thermal capacity
uniquely designed to eliminate operator fatigue, improve control and flexibility are required. The PS-90 features a rugged plug in heater
and enhance productivity in demanding soldering applications. with gold contacts. There are 15 single point soldering tips and over
The TD-100 uses a patented Tip-Heater Cartridge that is the 10 surface mount removal tips available for the PS-90.
best performing and lowest priced Tip-Heater Cartridge on See Pages 23-24 for tip selection
the market today! Almost 100 soldering tip geometries are
available as well as over 30 surface mount removal tips.
See Pages 18-21 for tip selection.
SX-90 SODR-X-TRACTOR ®
Shown with optional comfort grip 6993-0241-P1
The best performing, in-line, vacuum desoldering tool (SX-90 Sodr-
X-Tractor®) is ideal for Thru-Hole desoldering when fitted with SX-90
Desoldering tips and for SMT land clean-up when fitted with SX-90
Flo-D-Sodr® tips. SX-90 Desoldering tips are the longest lasting, best
MT-100 MINITWEEZ ™ performing desoldering tips on the market! The SX-90 features a unique
solder collection system that can utilize disposable Flux/Solder traps or
The only high capacity, micro tweezer (MT-100 MiniTweez™) a reusable glass collection chamber. An operator replaceable plug-in
on the market today features soft comfort grips, the smallest heater cartridge that can be changed in seconds is standard. There is a
stroke available, and its tweezing action mimics the natural wide range of standard and precision SX-90 Desoldering tips for when
motion of the human hand to eliminate hand fatigue. With 10 access is tight! See Page 25 for tip selection.
styles of component removal tips available, the MT-100 is one
of the most versatile component removal tweezers and our tips
cost less than half of our competitors! TT-65 THERMOTWEEZ ®
See Page 22 for tip selection.
The most versatile and only patented SMT removal tool (TT-65
ThermoTweez®) provides safe, one-handed, rapid reflow and
component removal of PLCCs and other 4 or 2 sided SMT components.
Unlike other methods, its high thermal capacity and targeted heat
delivery remove even the largest SMDs in just seconds without
damaging the PCB or risking of adjacent component reflow; even on
heavy assemblies. The patented vertically oriented handpiece and a
wide variety of quick-change, slim-line tips easily reach into the tightest
spaces for fast, safe component removal. The TT-65 also features a
THERMOPIK ® 100 patented “stroke” adjustment to reduce hand fatigue for repetitive
operations. See Page 26 for tip selection.
The newest tool for SMT component removal the ThermoPik®
100. The TP-100 is designed to reflow and remove QFPs in
seconds. The integrated vacuum pik lifts the component from TJ-85 THERMOJET ®
the PCB upon reflow. Based on our unique MT-100 handpiece,
there isn’t another SMT removal tool that is more comfortable in When the precise application of hot air is required, our slim line
your hand. Over 10 styles of tips are available. air pencil (TJ-85 ThermoJet®) is ideal for delivering heat for the
See Page 22 for tip selection. installation and removal of chip components, SOTs, and SOICs.
Multiple quick-change nozzle sizes are available. The handpiece’s
slim line, pencil grip design maximizes operator comfort and control.
The TJ-85’s airflow is actuated with a foot pedal. Ideal for the precise
application of hot air for large SMDs down to 0201s.
See Page 26 for nozzle selection.

4 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 5
 HANDPIECE & POWER SOURCE CHARTS ST SYSTEMS
CHOOSE THE RIGHT INTELLIHEAT HANDPIECE FOR YOUR APPLICATION PRODUCTION SOLDERING STATIONS ST30, ST 50 & ST 70 POWER SUPPLIES

HANDPIECES Part Number includes handpiece and standard cubby *Does not include Handpiece
FEATURES: • IntelliHeat Control The ST 30 is a single channel system with dial control featuring IntelliHeat.
HANDPIECE DESCRIPTION PART NUMBERS Technology The system is packaged with the TD-100 ThermoDrive Soldering Iron or can
TD-100 Thermo-Drive Iron The most responsive soldering iron available. Uses tip-heater cartridges. 6993-0263-P1 • o
C/oF Temperature Scales be purchased as a Power Source only and combined with any of 4 optional
• Temperature Adjustment handpieces. The ST 30 improves quality, reduces costs and eliminates the
TD-100 N A nitrogen compatible version of the TD-100. Requires 6993-0271-P1. 6993-0272-P1
Lockout maintenance and calibration hassles associated with other systems. The
TD-100 with Instant SetBack Cubby A kit containing the TD-100 and Instant SetBack Cubby 6993-0281-P1
• ESD grounding jack heavy-duty metal housing makes this system the ideal choice for the harshest
MT-100 MiniTweez Tip-heater cartridge based tweezer for 2 sided SMD removal. 6993-0264-P1 • ESD Safe metal housing environments and the sloped face of the front panel is a standard feature for
TP-100 ThermoPik QFP removal tool with integrated component vacuum pick to lift reflowed component. 6993-0280-P1 • Stackable ease of use. An optional mounting bracket (P/N 1321-0609-P1) is available
PS-90 Universal Soldering Iron Our famous High Capacity Soldering Iron for the most demanding applications. 6993-0267-P1 • Can be mounted under to mount the system under a work-bench or shelf, preserving precious bench
PS-90 N A nitrogen compatible version of the PS-90. 6993-0274-P1
workbench or shelf with top space. The optional Instant-SetBack Cubby is available for the TD-100
optional bracket ThermoDrive Soldering Iron to extend tip life, especially beneficial when Lead
SX-90 Sodr-X-Tractor The latest innovation in desoldering. Features disposable or reuseable solder traps. 6993-0266-P1
1321-0609-P1 Free solders are used.
TT-65 ThermoTweez High capacity tweezer for large or small SMDs. 6993-0268-P1
TJ-85 ThermoJet A foot-pedal activated precision air pencil for the installation or removal of SMDs. 6993-0270-P1
FEATURES: • IntelliHeat Control The ST 50 is a single channel, digital power supply that is available with
SX-90 Heat Sleeve Maintains comfortable temperature in heavy use applications. 6993-0229-P1 the TD-100 ThermoDrive Soldering Iron or PS-90 SensaTemp Soldering Iron.
Technology
Instant Setback Cubby for TD-100* Reduces tip temperature when iron is not in use. 6019-0077-P1 • Digital Display & Keypad The ST 50 can also be purchased as a Power Source only and combined
Nitrogen Regulator Accessory Controls the flow of nitrogen to tip. 6993-0271-P1 • o
C/oF display options with any of 4 optional handpieces. The programmable features of the ST 50
N2 Manifold Kit Connect up to 10 N2 irons to a single N2 source. 6993-0277-P1 • Password lockout cannot be found anywhere on similarly priced systems! The ST 50 improves
• Temperature SetBack quality, reduces costs and eliminates the maintenance and calibration
• Auto-Off hassles associated with other systems. The ST 50 features IntelliHeat Control
KITS & APPLICATIONS Tip Heater Cartridge Technology Handpieces SensaTemp Technology Handpieces
• Definable operating Technology. The heavy-duty, durable metal housing ensures years of service
KITS & APPLICATIONS TD-100 MT-100 TP-100 PS-90 SX-90 TT-65 TJ-85 and the sloped face of the front panel is a standard feature for ease of use.
temperature range
Handpiece Kits 6993-0263-P1
6993-0264-P1 6993-0280-P1 6993-0267-P1 6993-0266-P1 6993-0268-P1 6993-0270-P1 • ESD grounding jack An optional mounting bracket (P/N 1321-0609-P1) is available to mount the
(includes handpiece and tool stand) 6993-0281-P1
• ESD Safe metal housing system under a work-bench or shelf, preserving precious bench top space.
Handpiece Only Part Number 6010-0147-P1 6010-0148-P1 6010-0158-P1 6010-0150-P1 6010-0149-P1 6010-0151-P1 6010-0153-P1 • Stackable The optional Instant-SetBack Cubby is available for the TD-100 ThermoDrive
High Cycle Soldering ✓ ✓ • Can be mounted under Soldering Iron to extend tip life, especially beneficial when Lead Free solders
Standard Soldering ✓ ✓ workbench or shelf with are used.
High Mass Soldering ✓ optional bracket
1321-0609-P1
Micro Soldering ✓
Chip Installation ✓ ✓ ✓ ✓ ✓ The ST 70 is a single channel system that is controlled by POWER
FEATURES: • IntelliHeat Control
Solder Wicking ✓ ✓ ✓ MODULES™ and comes with the ThermoDrive Soldering Iron (TD-100). The
Technology
Thru-Hole Desoldering ✓ system can also be purchased as a Power Source only and combined with
• Performance level lockout
SMT Land Preparation ✓ ✓ ✓ ✓ any of 4 optional IntelliHeat handpieces. The ST 70 is the easiest to operate.
(if Power Module is
Simply select the performance level you desire, plug in the appropriate Power
Solder Removal from Lands ✓ removed the system is shut
Module and the system takes care of the rest! The ST 70 improves quality,
Large SMD Removal ✓ ✓ down.)
reduces costs while protecting your process. The heavy-duty metal housing
• ESD grounding jack
Standard SMD Removal ✓ ✓ ✓ ✓ ✓ makes this system the ideal choice for the harshest environments and the
• ESD Safe metal housing
Micro SMD Removal ✓ ✓ ✓ ✓ ✓ sloped face of the front panel is a standard feature for ease of use. An
• Stackable
Large Component Installations* ✓ ✓ ✓ optional mounting bracket (P/N 1321-0609-P1) is available to mount the
• Can be mounted under
system under a work-bench or shelf, preserving precious bench top space.
Standard Component Installations* ✓ ✓ ✓ workbench or shelf with
The optional Instant-SetBack Cubby is available for the TD-100 ThermoDrive
Micro Component Installations* ✓ ✓ ✓ optional bracket
Soldering Iron to extend tip life, especially beneficial when Lead Free solders
1321-0609-P1
INTELLIHEAT POWER SOURCE & HANDPIECE COMPATIBILITY
*with Solder Paste
are used.
• Supplied with 6.5, 7 and
Power Source Options - ST and MBT Systems ✓= Optional Handpiece ★ = Standard handpiece packaged with System 7.5 Power Modules
TIP-HEATER CARTRIDGE HANDPIECES ST 30 ST 50 ST 65 ST 70 ST 75 ST 100 ST 115 MBT 301 MBT 350 POWER MODULE PART NUMBER COLOR
• TD-100 ★ ★ ✓ ★ ✓ ★ ✓ ★ ★ Heat Level 5 1207-0446-01-P1 Green
• MT-100 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ★ Heat Level 5.5 1207-0446-02-P1 Blue
• TP-100 ✓ ✓ ✓ ✓ ✓ Heat Level 6 1207-0446-03-P1 Orange
SENSATEMP HANDPIECES ST 30 ST 50 ST 65 ST 70 ST 75 ST 100 ST 115 MBT 301 MBT 350 Heat Level 6.5 1207-0446-04-P1 Gold
• PS-90 ✓ ★ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Heat Level 7 1207-0446-05-P1 Red
• SX-90 ★ ★ ★ ★ ★ Heat Level 7.5 1207-0446-06-P1 Purple
• TT-65 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Heat Level 8 1207-0446-07-P1 Black
• TJ-85 ✓ ✓ ✓ ✓ Heat Level 8.5 1207-0446-08-P1 Silver

6 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 7
 DUAL CHANNEL SOLDERING SYSTEMS LEAD FREE ACCESSORIES
SOLDERING & REWORK SYSTEMS CUSTOMIZE YOUR SYSTEM FOR EVEN GREATER FLEXIBILITY

ST 100 THE ANSWER FOR THE LEAD FREE The optional INSTANT-SETBACK CUBBY is available for
SOLDER TRANSITION... use with the ST 30, ST 50, ST 65, ST 70, ST 75, ST 100 and
ST 115. When connected, it automatically puts the system into
SetBack mode when the TD-100 Iron has been in the cubby for
While transitioning from lead containing solders to Lead 45 seconds. SetBack mode means that the temperature is set
Free solders a very real problem is that most soldering to just below solder melt temperature so the corrosive action
operations will need to utilize Lead Free AND lead containing of the leaded or Lead Free solder is stopped, maximizing the
solders at the same time. Having only one soldering iron, or life of your tips! The system returns to normal operation when
other handpiece, on the bench will ultimately lead to cross- the iron is removed from the cubby. The part number for the
contamination issues and result in lower productivity and Instant-SetBack Cubby is 6019-0077-P1. The Instant-SetBack
potentially, higher costs. The ST 100 is a fully programmable Cubby is also available for use with the TD-100 fitted with the
system featuring two, individually controlled, IntelliHeat Green Lead-Free moulded Comfort Grip as part number 6019-
compatible handpiece channels. The system allows for 2 0078-P1.
soldering irons, 2 MiniTweezers or one of each to co-exist on
a workbench. Color coding accessories that clearly identify
which handpiece is designated for use with Lead Free and lead
containing solders are available. To maximize tip life and reduce operating costs, PACE’s
well recognized “SetBack” and “Auto-Off” features are LEAD FREE IDENTIFIABLE During the transition from
The ST 100 is loaded with features to improve quality, control included. The system will automatically reduce the set leaded to Lead Free solders, it will not be uncommon to be
your process, increase through-put, and extend tip life. The temperature to below solder melt temperatures, then turn using both types of solders at the same time. To assist in
system is fully programmable and can be password protected off after a user defined period of inactivity, from 10 to 90 reducing cross contamination of soldering tools and to keep
to prevent unauthorized changes. When high-mass tips are minutes each. To really protect the more expensive tip-heater additional tips separated on a workbench, PACE is pleased
used, an offset can be programmed into the system. cartridge and fine point soldering tips from oxidation, the to offer a variety of options to clearly identify handpieces and
TD-100 iron can be used with the PACE’s “Instant-SetBack tool stands being used with Lead Free solders. The handpieces
Technicians can become frustrated with being locked into a Cubby”. The cubby puts the iron’s channel into SetBack if are identified by green comfort grips and the tool stands are
single temperature. Additionally, a higher set temperature it has been in the cubby for more than 45 seconds! Up to identified with green cubbies. These options are available for
is often desired when working with Lead Free solders. The two Instant-SetBack cubbies can be connected to the ST 100. the TD-100, MT-100 and PS-90 handpieces in the following
ST 100 has the solution! An approved, unique, operating configurations.
range or process window, can be programmed FOR EACH The backlit, digital, LCD screen displays the temperature of both
HANDPIECE, allowing operators the flexibility to do their work, handpiece channels or with scan mode activated will cycle
while eliminating the risks associated with giving techs access through the handpiece channels one at a time displaying set
to the entire temperature range of the system. Also, a process and actual temperatures. The backlight and character contrast
window can be defined for the handpiece using leaded on the display can be adjusted to meet individual preferences.
solder, and a separate process window can be defined for the Finally, the system can be programmed with the name of the DESCRIPTION PART NUMBER
handpiece using lead containing solder. Operators can be operator or company which is displayed when the system is
given a range of 5 to 450OF to operate within! Lead Free Cubby (Available Nov 07) with Green Insert for TD-100 6019-0079-G-P1
turned on.
Green Replacement Handpiece Insert for TD-100 1140-0081-G-P1
MT-100/TP-100 Green, Lead Free Handpiece Cubby (Available Nov 07) 6019-0080-G-P1
MT-100/TP-100 Green, Lead Free Handpiece Insert (Available Nov 07) 1257-0383-G-P1
Green Comfort Grip and Green Handpiece Insert for TD-100 Tip & Tool Stand 6993-0283-P1
Replacement Green Comfort Grips for TD-100, pack of 5 1119-0176-P5
Instant SetBack Tip & Toold Stand for TD-100 with Green insert 6019-0078-P1
Green Replacement Handpiece Insert for TD-100 Tip & Tool Stand (Before Nov 07) 1140-0075-G-P1
Green Comfort Grip and Green Handpiece Insert for MT-100 Tip & Tool Stand 6993-0284-P1
Replacement Green Comfort Grips for MT-100, pack of 2 1119-0177-P2
Green Replacement Handpiece Insert for MT-100 Tip & Tool Stand (Before No 07) 1257-0323-G-P1
PS-90 Handpiece (IntelliHeat Version) with Green Comfort Grip 6010-0159-P1
PS-90 Tip & Tool Stand with Green Insert 6019-0074-P1
PS-90 Lead Free Cubby with Green Insert (Available Nov 07) 6019-0081-G-P1
Replacement Green Handpiece Insert for PS-90 1140-0083-G-P1

8 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 9
 SOLDERING & REWORK SYSTEMS PACE REWORK AND REPAIR
ST 65, ST 75 & ST 115 POWER SUPPLIES ST SYSTEM SPECIFICATIONS

The ST 65 is a single channel, dial control power supply that is FEATURES: SPECIFICATIONS ST 30 ST 50 ST 70 ST 100
compatible with all IntelliHeat handpieces and comes as a system
System with TD-100 115v 8007-0499 8007-0500 8007-0504 8007-0525
with the new SX-90 Sodr-X-Tractor or as a Power Source only. • IntelliHeat Control Technology
System with PS-90 115v N/A 8007-0532 N/A N/A
Featuring a powerful multistage venturi that is powered by your • Dial control
compressed air source, the ST 65 is ideal for application where • o
C/oF Temperature Scales Power Source Only 115v 8007-0497 8007-0501 8007-0505 8007-0524
continuous vacuum or pressure is required. An N2 source can • Temperature lockout System with TD-100 230v 8007-0512 8007-0514 8007-0518 8007-0527
be connected to create an inert gas reflow environment when • Patented Snap-Vac Technology System with PS-90 230v N/A 8007-0533 N/A N/A
using an N2 capable soldering iron. The heavy-duty, durable • ESD grounding jack Power Source Only 230v 8007-0513 8007-0515 8007-0519 8007-0526
metal housing ensures years of service and the sloped face of • ESD Safe metal housing Power Requirements 97-127 VAC, 50/60 Hz, 90 Watts max. 197-253 VAC, 50/60 Hz, 90 Watts max.
the front panel is a standard feature for ease of use. An optional • Stackable
Dimensions 104mm H x 130mm W x 152mm D 135mm H x 165mm W x 260mm D
mounting bracket (P/N 1321-0609-P1) is available to mount the • Can be mounted under (4.1” H x 5.1” W x 6.0” D) (5.3” H x 6.5” W x 9.25” D)
system under a work-bench or shelf, preserving precious bench workbench or shelf with
Weight 5 Kg (11 lbs.)
top space. N2 capable soldering iron. optional bracket 1321-0609-P1
Control Dial LED Display Power Module LCD Display & Keypad
Control Technology IntelliHeat
Tip to Ground Resistance 2 ohms or less
The ST 75 and ST 115 are ideal for users having to deal with wide ranges of applications. With these systems, you can solder, desolder,
Temperature Accuracy Meets or exceeds ANSI-J-STD 001 N/A Meets or exceeds ANSI-J-STD 001
remove components with a variety of tweezers and thermo-piks, as well as make use of the high performance, foot pedal activated, air pencil.
Absolute Temperature Stability ± 1.1°C (± 2 °F) at idle tip temp.
The systems come standard with PACE’s patented SNAPVAC desoldering technology to ensure quick, clean removal of solder from any through-
hole joint. The Hi-Flo pump is so powerful that you won’t lose vacuum in continuous use applications when removing residual/excess solder Tip Heater Cartridge Technology Handpieces = 205° to 454°C (400° to 850°F)
Temperature Range SensaTemp Dial Control 176°C to 482°C (350°F to 900°F)
from surface mount leads. The new, high resolution pressure control valve delivers the widest range of adjustable airflow available on the market SensaTemp Digital Control 37°C to 482°C (100°F to 900°F)
today. So if you’re using the new TJ-85 to reflow a PLCC or an 0201 resistor, you always have the precise level of control that you need to get
System Can be Calibrated Yes
the job done right!

SPECIFICATIONS ST 65 ST 75 ST 115
ST 75 A single channel, dial control power supply, the ST 75 FEATURES: System 115v 8007-0502 8007-0506 8007-0508
is compatible with all IntelliHeat handpieces and comes as a
• IntelliHeat Control Technology Power Source Only 115v 8007-0503 8007-0507 8007-0509
system with the new SX-90 or as a Power Source only. The ST 75
improves quality, reduces costs and eliminates the maintenance • Dial control System 230v 8007-0516 8007-0520 8007-0522
and calibration hassles associated with other systems. The • o
C/oF Temperature Scales Power Source Only 230v 8007-0517 8007-0521 8007-0523
heavy-duty, durable metal housing ensures years of service and • Temperature lockout Power Requirements 97-127 VAC, 50/60 Hz, 90 Watts max. 97-127 VAC, 50/60 Hz, 120 Watts max.
the sloped face of the front panel is a standard feature for ease • Hi-Flo Pump 197-253 VAC, 50/60 Hz, 90 Watts max. 197-253 VAC, 50/60 Hz, 120 Watts max.
of use. • Patented Snap-Vac Technology
Dimensions 104mm H x 130mm W x 152mm D 88mm H x 171mm W x 254mm D
• ESD grounding jack (4.1” H x 5.1” W x 6.0” D) (3.5” H x 6.75” W x 10” D)
• ESD Safe metal housing
Weight 2.3 Kg (5 lbs.) 4 Kg (9 lbs.)
• Stackable
Control Dial Dial LED Display & Keypad
Control Technology IntelliHeat
ST 115 A single channel, digital display, fully programmable FEATURES: Tip to Ground Resistance 2 ohms or less
power supply, the ST 115 is compatible with all IntelliHeat Temperature Accuracy Meets or exceeds ANSI-J-STD
handpieces and comes as a system with the new SX-90 or as • IntelliHeat Control Technology Absolute Temperature Stability ± 1.1°C (± 2 °F) at idle tip temp.
a Power Source only. The programmable features of the ST • Digital Display & Keypad
Temperature Range Tip Heater Cartridge Technology Handpieces = 205° to 454°C (400° to 850°F)
115 cannot be found anywhere on similarly priced systems! • o
C/oF display options
SensaTemp Dial Control 176°C to 482°C (350°F to 900°F)
The ST 115 improves quality, reduces costs and eliminates the • Password lockout SensaTemp Digital Control 37°C to 482°C (100°F to 900°F)
maintenance and calibration hassles associated with other • Temperature SetBack
System Can be Calibrated Yes
systems. The heavy-duty, durable metal housing ensures years • Auto-Off
Vacuum/Pressure Source Type Compressed Air Powered Venturi Self Contained Pump
of service and the sloped face of the front panel is a standard • User defined operating
temperature range Vacuum Rise Time 150 ms Average
feature for ease of use.
• Hi-Flo Pump Vacuum (Nominal) 20 in Hg max
• Patented Snap-Vac Technology Flow Control Valve Coarse Adjustment High Precision Needle Valve
• ESD grounding jack Pressure (Nominal) 18 p.s.i. max
• ESD Safe metal housing Air Flow (Nominal) 8 slpm max
• Stackable

10 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 11
 MBT 301 MBT 350
SIMPLE AND EASY TO USE FOR REWORK TECHNICIANS OR OPERATORS ON THE LINE ADVANCED TECHNOLOGY AND PROGRAMMABILITY

The MBT 301 is a multi-technology system with The MBT 350 is loaded with features to improve
two, individually controlled, universal handpiece quality, increase through-put, extend tip life, and
channels. The system features a two-line back lit protect your process. The system is fully programmable
LCD display. The programmable features include: and can be password protected from unauthorized
password protection from unauthorized changes, changes. In some cases technicians become frustrated
a user definable temperature operating range, and with being locked into a single temperature. The MBT
"SetBack" & "Auto-Off" functions to preserve tip life. 350 provides the solution! An approved operating
To protect your more expensive tip-heater cartridge range can be programmed allowing operators the
and fine point soldering tips from oxidation, the flexibility to do their work, while eliminating the risks
TD-100 can be used with the optional "Instant- associated with giving techs access to the entire
SetBack Cubby". The cubby puts the iron's channel temperature range of the system. Operators can be
into setback if it is idle in the cubby for more than given a range of 5 to 450˚F (3-250˚C) to operate
45 seconds! One Instant SetBack Cubby can be within! When high-mass tips are required, an offset
connected to the MBT 301. can be programmed for each of the three channels,
individually.
The new dual purpose vacuum/pressure pump and delivery system featuring PACE's patented SNAP-VAC Technology, provides the
most vacuum available for desoldering applications. When used with an air pencil, the high resolution, pressure control valve allows To maximize tip life and reduce operating costs, PACE's well recognized “SetBack” and “Auto-Off” features are included. The system
for precise adjustment when working on the smallest components such as 0201's. will automatically reduce the set temperature by 50% then turn off after a user defined period of inactivity, from 1 to 90 minutes. To
really protect your more expensive tip-heater cartridge and fine point soldering tips from oxidation, the TD-100 can be used with the
new “Instant-SetBack Cubby”. The cubby puts the iron's channel into setback if it’s in the cubby for more than 45 seconds! Up to
two Instant SetBack cubbies can be connected to the MBT 350.
MBT 300 SERIES SPECIFICATIONS
The new dual purpose vacuum/pressure pump and delivery system featuring PACE's patented SNAP-VAC Technology, provides the
SPECIFICATIONS MBT 301 MBT 350 MBT 301 E MBT 350 E most vacuum available for desoldering applications. When used with an air pencil, the high resolution, pressure control valve allows
for precise adjustment when working on the smallest components such as 0201's.
Kit with Handpieces Part Numbers: 8007-0478 8007-0454 8007-0479 8007-0455
(TD-100 & SX-90) (TD-100, MT-100 & (TD-100 & SX-90) (TD-100, MT-100 &
The new backlit, digital, LCD screen displays the temperature of all three handpiece channels or, with scan mode activated, will cycle
SX-90) SX-90)
Power Source Only Part Numbers: through the handpiece channels one at a time displaying set and actual temperatures. The backlight and character contrast on the
8007-0480 8007-0452 8007-0481 8007-0453
display can be adjusted to meet individual preferences. And finally, the system can be programmed with the name of the operator
Power Requirements 120 VAC, 60 Hz (240 watts maximum) 230 VAC, 50 Hz (240 watts maximum) or company which is displayed when the system is turned on.

Handpiece Technology Compatibilty IntelliHeat Handpieces with Tip Heater Cartridge or SensaTemp Technology

Dimensions 135mm H x 165mm W x 260mm D (5.3” x 6.5” x 9.25”)

1. TD-100 THERMO-DRIVE IRON 1. 2. 3.
Weight 5 Kgs (11 lbs.) 2. MT-100 MINITWEEZ
3. PS-90 UNIVERSAL IRON
Tip to ground resistance < 2 Ohms
4. TT-65 THERMOTWEEZ
Temperature Stabililty ± 1.1 C (2 F)
O O 5. TJ-85 THERMOJET
6. SX-90 SODR-X-TRACTOR
Temperature Accuracy Meets or exceeds ANSI J Std 001 7. TP-100 THERMOPIK

37-482 OC (100-900 OF) SensaTemp

Set Temp Range
205-454 OC (400-850 OF) tip Heater Cartridge 4. 5. 6. 7.

Vacuum Rise Time 150 ms Average as measured with PACE Process Monitor

Vacuum 20 in Hg max

Pressure 18 p.s.i. max

Air Flow 8 SLPM max

12 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 13
 SENSATEMP REWORK SYSTEMS LEAD FREE SOLDERING
ST 25, MBT 250 & PRC 2000 WORKING WITH LEAD FREE SOLDERS

The PRC 2000 Benchtop Factory is the ultimate rework Lead Free solders do not behave or look like their lead containing counterparts. As our industry changes over to Lead Free solders,
center. The PRC 2000 can tackle just about any Thru-Hole, individual PCB assemblers will need to address several issues relating to hand soldering and rework. These issues include:
SMT application and is well suited for multilayer repairs on
damaged or prototype PCBs. Featuring 3 simultaneously active • Higher melting temperatures – which mistakenly lead to operators increasing equipment operating temperatures. Higher
SensaTemp handpiece channels, a built-in paste dispenser, MicroChine for removing conformal coatings or grinding away PCB operating temperatures do not make the process quicker, they can actually slow it down.
laminate, and pulse heat technology. The PRC 2000 comes with 9 handpieces and continuously calibrates automatically.
• Poor wetting and spreading properties – Additional time is required when working with lead free solders, they do not
spread or wet like lead containing solders do. Operators must slow down.
The ST 25 soldering system uses SensaTemp to maximize heat delivery and improves quality, reduces costs and eliminates the
maintenance and calibration hassles associated with other soldering systems. The heavy-duty metal housing makes this system the ideal
• Difficult to work with - Bridging and insufficient solder defects are common, even for experienced operators, leading to
choice for the harshest environments and the sloped face of the front panel is a standard feature for ease of use. An optional mounting
operator frustration and poor quality.
bracket (P/N 1321-0609-P1) is available to mount the system under a work-bench or shelf, preserving precious bench top space.

FEATURES:
• Dull grainy finish – makes inspection difficult.
• SensaTemp Control Technology MBT 250
• Analog (dial) control
• o
C/oF Temperature Scales SD/SDTP Because Lead Free solders oxidize quickly, more aggressive Tip-Brite is a high quality tip tinner that will remove stubborn
• Temperature Adjustment Lockout Still Available and longer lasting fluxes are required to keep surfaces clean oxidation.
• ESD grounding jack and free from oxidation. Working with no-clean fluxes is
• ESD Safe metal housing challenging as their process window is often small. Once they The use of equipment with SetBack and Auto-Off functions
• Stackable are burned off, oxidation immediately begins to form which (standard on all PACE equipment), is very desirable. Additionally,
• Can be mounted under work
can result in a marginal or defective solder joint. Additionally, optional accessories such as PACE’s Instant SetBack Cubby
bench or shelf with optional bracket 1321-0609-P1
increasing operating temperatures creates an ideal environment ensure that tip life is maximized. The Instant SetBack Cubby puts
for oxidation to form and will also lead to flux and solder ball the system into “SetBack” after 45 seconds of inactivity. When
SENSATEMP POWER SOURCE SPECIFICATIONS splatter on the PCB. If the flux is splattered all over the PCB, it’s the iron is removed from the cubby, it restores itself to the set
SPECIFICATIONS ST 25 MBT 250 SD/MBT 250 SDTP PRC 2000 SMT PRC 2000 TH not able to do its job on the surfaces to be joined during the temperature almost immediately.
soldering process.
8007-0203 (SD)
System 115 V 8007-0528
8007-0206 (SDTP)
8007-0132 8007-0138 The use of nitrogen assisted soldering equipment helps to
Power Source Only 115 V 8007-0529 8007-0349 N/A N/A
Lead Free solders also affect soldering and rework tools and their mitigate the problems associated with using Lead Free solders.
effect is detrimental. Lead Free solders contain high percentages Nitrogen helps on two fronts. First, it creates an inert environment
8007-0204 (SD)
System 230 V 8007-0510
8007-0207 (SDTP)
8007-0133 N/A of tin, almost always over 94%. Tin is a corrosive and active around the soldering tip, reducing the potential for tip to oxidize.
metal. When it mixes with iron (the protective layer on soldering Second, it assists in the soldering process at the PCB level by
Power Source Only 230 V 8007-0511 8007-0353 N/A N/A
tips), an inter-metallic compound is formed that wears away purging oxygen from the immediate area which reduces or
Input Power Requirements 97-127 VAC, 50/60 Hz or 197-253 VAC, 50/60 Hz
more quickly than the iron would either by itself or when used eliminates the formation of oxidation on the work site. This not
Max Power Consumption 120 W 240 W 400 W with lead containing solder. This causes two problems, one is only reduces the amount of flux that is required, but it also helps
104mm H x 130mm W x 135mm H x 165mm
175mm H x 350mm W x 230mm D shorter tip life as the protective iron coating is dissolved in the to improve wetting, spreading and leaves a finish that is shinier
Dimensions 152mm D W x 260mm D tin, and the second is that oxidation forms more quickly which is and less grainy.
(6.9" H x 13.75” W x 9.25" D)
(4.1" H x 5.1" W x 6.0" D) (5.3" H x 6.5” W x 9.25" D)
further exacerbated by the high temperature environment the tips
Weight 2.3 Kgs (5 lbs.) 5 Kgs (11 lbs.) 13 Kgs (28.6 lbs.)
work in. As a result, tin oxides form and create an inter-metallic PACE’s nitrogen assisted soldering systems pass the nitrogen
Control LED Display LED Display compound with the iron plating on the tip. Once the oxidation through or around the heater before it is directed to the work
Control Technology SensaTemp (Black Connector HandPieces) begins to form, the tip will lose its ability to wet with solder and if site. This “pre-heats” the immediate area which can also help
Tip to Ground Resistance 2 ohms or less not cleaned off quickly, it becomes almost impossible to remove to reduce thermal shock to component leads and to components
Temperature Accuracy Meets or exceeds ANSI-J-STD 001 and the tip must be replaced. themselves. Pre-heating also allows for the use of lower, safer
Absolute Temperature Stability ± 1.1°C (± 2 °F) at idle tip temp.
and more effective soldering temperatures.
When using Lead Free solders, regardless of alloy, it is absolutely
Temperature Range 176° to 482°C (350° to 900°F) nominal
imperative that tips are properly maintained, otherwise tip life PACE’s soldering systems offer legendary thermal control as well
System Can be Calibrated Calibration not required
will be reduced significantly. Tips should be cleaned frequently as advanced features to maintain your process. Unique PACE
Pump Type N/A Self Contained Pump to remove oxidation before it becomes impossible to remove. features such as IntelliHeat, Power Modules and password
Vacuum Rise Time N/A 150 ms Average Tips should always be tinned when not being used, otherwise protection ensure consistency and quality in your process.
Vacuum (Nominal) N/A 20 in Hg max oxidation will quickly form on the tip. If the iron will not be used Economical tips and standard features such as “SetBack” and
Flow Control Valve N/A High Resolution Needle Valve Coarse adjustment for extended periods of time, they should be turned off. Should “Auto-Off” maximize tip life to reduce operating costs and
Pressure (Nominal) N/A 18 p.s.i. max 7 p.s.i. max oxidation form that cannot be easily cleaned by tinning or by increase your bottom line.
using a cleaning tool, PACE’s Tip-Brite is recommended.
Air Flow (Nominal) N/A 8 slpm max 13 slpm max

14 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 15
 LEAD FREE SOLDERING LEAD FREE SOLDERING
LEAD FREE SOLDERING COMPATIBLE AND RoHS COMPLIANT NITROGEN ASSISTED SOLDERING ACCESSORIES

PACE’s soldering systems offer legendary thermal control as well as advanced features to maintain your process. Unique PACE features NF 50 & NF 100 NF 500 & NF 1000
such as IntelliHeat, Power Modules and password protection ensure consistency and quality in your process. Economical tips and
standard features such as “SetBack” and “Auto-Off” maximize tip life to reduce operating costs and increase your bottom line. The compact high- PACE is also pleased to offer
performance single the NF Series Nitrogen farms.
All ST & MBT systems, handpieces and tips are Lead Free soldering compatible and RoHS compliant. station N2 generator Nitrogen farms harvest N2 from
(NF 100) will generate a compressed air supply that is
They can be used with any Lead Free alloys without modification. PACE’s soldering systems, handpieces and tips are fully compatible Nitrogen Gas at a passed through a specialized
with your Lead Free process. PACE’s TD-100 soldering iron boasts one of the most efficient heat transfer capabilities and is clearly one of maximum concentration filter. The other atoms that
the most responsive irons on the market today. This means that the TD-100’s ability to recover from thermal loading and maintain its heat level of 99.9%. This make up “air” are forced
output is far superior to other conventional irons, eliminating the need for higher, unsafe temperatures when using Lead Free solders. system should be used through the filter, leaving
Quick and consistent heat transfer also ensures that flux is fully activated and burned off, leaving the work site properly prepared for in conjunction with NF a pure stream of N2 as the
the formation of highly reliable solder joints. Our PS-90 soldering iron has been the staple of the industry for years and is known for its 50 N2 Flow Control product of filtering. Nitrogen
amazing thermal capacity and ability to deliver the heat at safe, low temperatures. Both the TD-100 and PS-90 are available for use Unit. farms are passive collection
with nitrogen. devices which means that there
are no electrical or moving
parts, little or no maintenance,
HANDPIECE KIT HANDPIECE ONLY low running costs, and they
TD-100 N 6993-0272-P1 6010-0156-P1 maintain the balance of air/N2
PS-90 N 6993-0274-P1 6010-0157-P1 in a confined space (as long
as the compressed air is pulled
from the same space).
NF 100 PERFORMANCE TABLE
N2 Concentration %
99.9 99.5 99.0 98.0 97.0 96.0 95.0 90.0
0.3 0.15 0.37 0.48 0.66 0.88 1.1 1.3 2.6

Output amount
air pressure (MPa)
Input compression
0.4 0.24 0.57 0.77 1.1 1.4 1.7 2.0 4.4

(L/min)
0.5 0.35 0.75 1.1 1.5 1.9 2.2 2.9 5.9
All ST products are compatible with either the PS-90 N and/
0.6 0.48 0.97 1.3 1.8 2.4 3.1 3.5 7.5
or the TD-100 N handpieces. The benefits of nitrogen assisted
soldering are available for all of PACE’s soldering stations with 0.7 0.55 1.2 1.6 2.2 3.1 3.7 4.2 9.2
the N2 Regulator Accessory which can be easily mounted to any
ST system.
NF SYSTEMS DESCRIPTION PART NUMBERS
NF 50 Single station N2 regulator with shut off 8110-0500
NF 100 For a single station 8110-0100

All of PACE’s soldering, desoldering and component removal tips are tinned with Lead Free solder NF 500 For up to 2 stations 8110-0001
NF 1000 For up to 10 stations 8110-0002

Due to the corrosive nature of the high tin content in Lead Free When reworking area array components with Lead Free solder, Air tube O/D 6mm Air tube O/D 6mm Regulator Compressed, dry, filtered air
alloys and because more aggressive fluxes are commonly the greatest enhancement to existing equipment is the use of N2 OUT AIR IN
required when using Lead Free solders, we have also optimized nitrogen for reflow. All of PACE’s Area Array equipment comes
the iron plating on our tips to maximize thermal transfer while fitted for nitrogen use as standard.
providing for the longest life possible.
Additionally, PACE manufactures Fume Extraction Systems to
PACE is leading the way in soldering technology with our reduce exposure to harmful particulates and gases created
NF 100/50 CONNECTION METHOD
patented “Diamond Series” tips. “Diamond Series” tips are from hand soldering operations. PACE Fume Extraction Systems NF 100
manufactured with an iron matrix that is impregnated with sub effectively remove these contaminants from the workers breathing N2 Gas
micron sized diamond particles. The diamond-impregnated zone thereby reducing or eliminating health risks and improving Generator
N2 Soldering Iron
surface is harder and more corrosion resistant than iron alone. productivity.
• PS-90N
NF 50 N2 Flow Control Unit • TD-100N

16 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 17
 TD-100 STANDARD SOLDERING TIPS TD-100 STANDARD SOLDERING TIPS
TIP SPECIFICATIONS TIP SPECIFICATIONS

TIP SPECIFICATIONS TIP SPECIFICATIONS

TIPS DESCRIPTION TIP SIZE - L SIZE - D PART NUMBER TIPS DESCRIPTION TIP SIZE - L SIZE - D PART NUMBER

1/32" Conical Sharp Extended 13.4mm (0.530") 0.80mm (0.031") 1124-0001-P1 3/128" Conical Sharp Bent 30 Degrees 14.4mm (0.570") 0.58mm (0.023") 1124-0021-P1

1/64" Conical Sharp 7.8mm (0.310") 0.40mm (0.016") 1124-0002-P1 1/16" Conical Sharp 9.9mm (0.390") 1.60mm (0.063") 1124-0022-P1

1/64" Conical Sharp Bent 30 Degrees 7.8mm (0.310") 0.40mm (0.016") 1124-0003-P1 1/8" 90 Degree Chisel Extended 8.6mm (0.340") 3.20mm (0.125") 1124-0023-P1

1/64" Conical Sharp Extended 13.5mm (0.535") 0.40mm (0.016") 1124-0004-P1 1/16" 30 Degree Bevel 9.9mm (0.390") 1.60mm (0.063") 1124-0024-P1

13/64" Conical Sharp Extended 4.7mm (0.188") 0.80mm (0.031") 1124-0005-P1 1/16" Conical Sharp Extended 12.1mm (0.478") 1.60mm (0.063") 1124-0025-P1

3/128" Conical 4.6mm (0.184") 0.58mm (0.023") 1124-0006-P1 1/16" Chisel Bent 30 Degrees 9.7mm (0.385") 1.60mm (0.063") 1124-0026-P1

1/16" 90 Degree Chisel 10.9mm (0.430") 2.03mm (0.080") 1124-0007-P1 3/128" Conical Sharp 15.2mm (0.600") 0.58mm (0.023") 1124-0027-P1

3/64" 30 Degree Chisel 9.7mm (0.380") 1.20mm (0.047") 1124-0008-P1 3/64" Chisel, Bent 30 Degrees, Extended 15.2mm (0.600") 0.91mm (0.36") 1124-0028-P1

3/64" 30 Degree Bevel 3.6mm (0.140") 1.20mm (0.047") 1124-0009-P1 1/32" 30 Degree Bevel 9.1mm (0.360") 1.91mm (0.75") 1124-0029-P1

13/64" Extra Large Chisel 7.62mm (0.300") 5.15mm (0.203") 1124-0010-P1 1/32" Conical Sharp 9.9mm (0.390") 0.80mm (0.031") 1124-0030-P1

1/64" 60 Degree Bevel 14.7mm (0.580") 0.40mm (0.016") 1124-0011-P1 Heat Staking N/A 4.04mm (0.159") 1124-0031-P1

1/32" 30 Degree Chisel 9.1mm (0.360") 0.80mm (0.031") 1124-0012-P1 MiniWave N/A 3.05mm (.120") 1124-0032-P1

3/32" 30 Degree Chisel 9.9mm (0.390") 2.40mm (0.094") 1124-0013-P1 Angled MiniWave N/A 3.05mm (.120") 1124-0033-P1

5/64" 60 Degree Chisel 4.7mm (0.185") 2.00mm (0.078") 1124-0014-P1 Single Sided Chisel N/A 3.05mm (.120") 1124-0034-P1

1/64" Conical, Sharp, Bent 30 Degrees, Extended 15.1mm (0.595") 0.40mm (0.016") 1124-0015-P1 Angled MiniWave N/A 2.11mm (.083") 1124-0035-P1

3/64" Chisel Bent 30 Degrees 11.7mm (0.460") 1.20mm (0.047") 1124-0016-P1 1/128" Conical N/A 0.20mm (0.008") 1124-0036-P1

1/16" 60 Degree Chisel 15.8mm (0.620") 1.60mm (0.063") 1124-0017-P1 1/4 Flat Blade N/A 4.57mm (0.180") 1124-0037-P1

1/32" Conical Sharp Extended 16.7mm (0.660") 0.80mm (0.031") 1124-0018-P1 Single Sided Chisel, Fine Pitch N/A 1.5mm (.06") 1124-0038-P1

1/16" 30 Degree Chisel 9.9mm (0.390") 1.60mm (0.063") 1124-0019-P1 Angled MiniWave, Fine Pitch N/A 1.6mm (.064") 1124-0039-P1

1/8" 90 Degree Chisel 4.8mm (0.190") 3.20mm (0.125") 1124-0020-P1 MicroFine Single Sided Chisel N/A 0.9mm (.035”) 1124-0040-P1

MicroFine Single Sided Chisel N/A 1.1mm (.045”) 1124-0041-P1

MAXIMIZING TIP LIFE PACE recommends the following practices to maximize tip life. MicroFine Conical N/A 0.25mm (.01”) 1124-0042-P1

MicroFine Bent Conical N/A 0.76mm (.03”) 1124-0043-P1

1. Always use the lowest possible temperatures while soldering. High temperatures cause tips to oxidize faster, which
reduces heat transfer and damages the protective iron plating.
MicroFine Bent Conical N/A 0.5mm (.02”) 1124-0044-P1
2. Avoid aggressive fluxes whenever possible. Aggressive fluxes erode tips faster; shortening their useful life.
3. Always use a properly sized tip for the work. Tips, that are too small, will wear out faster and tips that are too large Angled Micro-Wave N/A 1.1mm (.045") 1124-0045-P1
will wear unevenly which, in turn, will change the tip geometry rendering it useless, possibly damaging pads.
4. Always tin tips when not in use and after cleaning on a damp sponge. A coating of solder will prevent oxidation Micro-Wave N/A 1.1mm (.045") 1124-0046-P1
from forming which causes tips to lose their tinning or wetting capability.
5. Always feed solder wire into the heated work, not the tip. Feeding solder directly into the tip will cause pin-holes in Angled Chisel 8.4mm (0.33") 1.33mm (0.051") 1124-0047-P1
the tip and will cause the flux in the solder wire to be burned off before it can activate and prepare the surfaces being soldered.
Single Sided Chisel 17.00mm (0.693") 4.55mm (0.178") 1124-0048-P1
Should tips lose their tinning or wetting capability, a tip cleaner such as PACE’s Tip-Brite may be used to restore them.

18 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 19
 UNIQUE TO PACE... PATENTED DIAMOND/IRON PLATING PROCESS USING
REAL DIAMONDS THAT PROVIDES IMPROVED THERMAL PERFORMANCE AND
LONG LIFE WHEN WORKING WITH LEAD FREE SOLDER

DIAMOND SERIES EXTENDED LIFE SOLDERING TIPS TD-100 SMT REMOVAL TIPS
FOR USE WITH THE TD-100 TIP SPECIFICATIONS

PROFILE DESCRIPTION PART NUMBER PROFILE DESCRIPTION PART NUMBER TIP - CHIP/SOT REMOVAL COMPONENT TYPE SIZE - A SIZE - B PART NUMBER
.06 Wide, Bevel 60 Degrees, Chip 0402 Angle (fig. A) 2.2mm (.085”) - 1124-0581-P1
.016 Conical 1126-0601-P1 1126-0625-P1
.12x.06 Oval Face Chip 0201 Angle (fig. A) 0.5mm (.02”) - 1124-0533-P1
(fig. A) (fig. E)
.039 Conical 1126-0602-P1 .07 Bevel, 60 Degree 1126-0626-P1 Chip 1808 (fig. B) 5.0mm (.195”) - 1124-0520-P1
Chip 0402 (fig. C) 1.0mm (.40”) - 1124-0521-P1
.055 Conical, Blunt 1126-0603-P1 (fig. B) (fig. F)
.078 Bevel, 45 Degree 1126-0627-P1
Chip 0201 (fig. C) 0.5mm (0.2”) - 1124-0534-P1
.031 Conical, Blunt 1126-0604-P1 .13 Bevel, 60 Degree 1126-0628-P1 SOT 23 (fig. D) 1.8mm (.070”) - 1124-0522-P1
(fig. C) (fig. G)
SOT 89 (fig. E) 2.8mm (.110”) - 1124-0523-P1
.016 Conical, Long 1126-0605-P1 .118 Bevel, 45 Degree 1126-0629-P1 Chip 1206 (fig. F) 3.6mm (.142”) - 1124-0524-P1
(fig. D)
.016 Conical 1126-0606-P1 Chip 0805 (fig. G) 2.4mm (.095”) - 1124-0525-P1
.023 Bevel, Special 1126-0630-P1
TIP - SOIC/SOP/TSOP REMOVAL COMPONENT TYPE SIZE - A SIZE - B PART NUMBER
.016 Conical, Extended 1126-0607-P1 .031 Chisel Standard 1126-0631-P1
SOIC 14/16 5.2mm (.205”) 10.5mm (.415”) 1124-0504-P1
.024 Conical 1126-0608-P1 .047 Chisel Standard 1126-0632-P1 SOIC 20 9.6mm (.377”) 13.6mm (.535”) 1124-0505-P1
SOP 28 10.8mm (.426”) 18.6mm (.734”) 1124-0506-P1
.039 Conical 1126-0609-P1 .062 Chisel Standard 1126-0633-P1 SOP 40 11.9mm (.467”) 25.7mm (1.011”) 1124-0507-P1

.031 Conical 1126-0610-P1 SOP 44 13.1mm (.516”) 28.4mm (1.120”) 1124-0508-P1

.094 Chisel Standard 1126-0634-P1
TSOP 56 18.8mm (.739”) 14.1mm (.557”) 1124-0509-P1
.047 Conical 1126-0611-P1 .157 Chisel Standard 1126-0635-P1 TSOP 28 12.0mm (.471”) 8.5mm (.333”) 1124-0510-P1
SOIC 8 5.1mm (.202”) 4.65mm (.183”) 1124-0519-P1
.016 Conical Bent 1126-0612-P1 .205 Chisel Standard 1126-0636-P1
TSOP 40 18.8mm (.740”) 10.4mm (.410”) 1124-0526-P1
.016 Conical, Blunt, Bent 1126-0613-P1 .157 Chisel Long Reach 1126-0637-P1 TIP - SOIC/SOP/TSOP REMOVAL COMPONENT TYPE SIZE - A SIZE - B PART NUMBER

.016 Conical, Blunt 1126-0614-P1 PLCC 28 Socket 9.3mm (.365”) 9.3mm (.365”) 1124-0511-P1
.205 Chisel Long Reach 1126-0638-P1
PLCC 32 14.2mm (.561”) 11.7mm (.459”) 1124-0512-P1
.016 Conical Extended, Bent 1126-0615-P1 .078 Chisel Blunt 1126-0639-P1 PLCC 44 16.8mm (.622”) 16.8mm (.622”) 1124-0513-P1
QFP 144 20.6mm (.810”) 20.6mm (.810”) 1124-0514-P1
.157 Bevel, 45 Degree 1126-0616-P1 .125 Chisel Blunt 1126-0640-P1
PLCC 28 11.8mm (.465”) 11.8mm (.465”) 1124-0515-P1
.078 Bevel, 60 Degree 1126-0617-P1 .055 Chisel, Bent 30 Degrees 1126-0641-P1 QFP 100/128 22.0mm (.865”) 16.0mm (.628”) 1124-0516-P1
PLCC 18 7.6mm (.300”) 12.8mm (.505”) 1124-0528-P1
.118 Bevel, 60 Degree 1126-0618-P1 .062 Chisel, Bent 30
1126-0642-P1 TQFP 80 12.5mm (.491”) 12.5mm (.491”) 1124-0529-P1
Degrees
.157 Bevel, 45 Degree Tinned on PLCC 52 19.4mm (.762”) 19.4mm (.762”) 1124-0530-P1
1126-0619-P1
edge/face .055 Chisel, Bent, Extended 1126-0643-P1
QFP 100 26.6mm (1.048”) 26.6mm (1.048”) 1124-0531-P1
.039 Bevel, 60 Degree, Extended 1126-0620-P1 .185 Knife, 45 Degree 1126-0644-P1 VQFP 100 15.5mm (.610”) 15.5mm (.610”) 1124-0535-P1

.039 Bevel, 45 Degree TQFP 64 15.3mm (.602”) 15.3mm (.602”) 1124-0537-P1

1126-0621-P1 .181 Knife, 45 Degree 1126-0645-P1
Tinned on edge / face
TIP - SOIC/SOP/TSOP REMOVAL COMPONENT TYPE SIZE - A SIZE - B PART NUMBER
.078 Bevel, 45 Degree .185 Knife, 45 Degree,
1126-0622-P1 1126-0646-P1 Blade 6mm (.236”) - 1124-0536-P1
Tinned on edge / face Blunt
Blade 10.8mm (.425”) - 1124-0501-P1
.118 Bevel, 45 Degree .118 Knife, 45 Degree 1126-0647-P1
1126-0623-P1
Tinned on edge / face Blade 16.0mm (.630”) - 1124-0502-P1
Single Sided Chisel .08 Blade 21.2mm (.835”) - 1124-0503-P1
.039 Bevel, 45 Degree 1126-0624-P1 1126-0648-P1
Wide
Blade 25.0mm (.984”) - 1124-0532-P1
* Drawings are representative of tips actual shape. Actual tips may differ somewhat, other than front end geometry.

20 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 21
 MT-100 AND TP-100 SMT REMOVAL TIPS PS-90 SOLDERING TIPS
TIP SPECIFICATIONS TIP SPECIFICATIONS

MT-100 TIPS TIPS DESCRIPTION TIP SIZE PART NUMBER

TIP - CHIP/SOT REMOVAL COMPONENT TYPE SIZE - A SIZE - B PART NUMBER

1/16" Chisel 1.60mm (0.063") 1121-0335-P5
Chip (fig. A) 0.2mm (.008”) 0.2mm (.008”) 1124-1001-P1

(fig. A) (fig. B)
Chip, SOT (fig. B) 0.7mm (.03”) 0.5mm (.03”) 1124-1002-P1 1/32" Conical 0.80mm (0.031") 1121-0336-P5

Chip, SOT (fig. B) 0.7mm (.03”) 1mm (.04”) 1124-1003-P1

1/8" Chisel 3.20mm (0.125") 1121-0337-P5

Chip, SOT (fig. B) 0.7mm (.03”) 2mm (.08”) 1124-1004-P1
(fig. C)

Chip, SOT, TSOPS (fig. C) 0.7mm (.03”) 6mm (.24”) 1124-1005-P1

1/16" Chisel (MicroFine) 1.60mm (0.063") 1121-0349-P5
Chip, SOT, TSOPS (fig. C) 0.7mm (.03”) 8mm (.31”) 1124-1006-P1

Chip, SOT, TSOPS (fig. C) 0.7mm (.03”) 10mm (.39”) 1124-1007-P1

1/32" Chisel 0.80mm (0.031") 1121-0359-P5

Chip, SOT, TSOPS (fig. C) 0.7mm (.03”) 13mm (.51”) 1124-1008-P1

Chip, SOT, TSOPS (fig. C) 0.7mm (.03”) 18mm (.74”) 1124-1009-P1 3/32" Chisel 2.40mm (0.094") 1121-0360-P5

Chip, SOT, TSOPS (fig. C) 0.7mm (.03”) 28mm (1.09”) 1124-1010-P1

1/32" Bent Chisel 0.80mm (0.031") 1121-0361-P5

TP-100 TIPS Single-Sided Chisel 3.30mm (0.13") 1121-0406-P5

COMPONENT COMPONENT
TIP TYPE LEAD COUNT SIZE - A SIZE - B PART NUMBER
HEIGHT FOOTPRINT
1/16" Chisel (High Capacity) 1.60mm (0.063") 1121-0414-P5
LQFP/TQFP 80 12mm (.472”) 12mm (.472”) 1.4mm 2.0mm 1124-2001-P1

64, 80,100,
LQFP/TQFP 14mm (.551”) 14mm (.551”) 1.4mm 2.0mm 1124-2002-P1
A 120, 128, 168 Mini-Wave 3.30mm (0.13") 1121-0490-P5
128, 144,
LQFP/TQFP 20mm (.788”) 20mm (.788”) 1.4mm 2.0mm 1124-2003-P1
160, 176
B LQFP/TQFP 176, 216 24mm (.945”) 24mm (.945”) 1.4mm 2.0mm 1224-2004-P1 1/16" Chisel, Long Reach 1.60mm (0.063") 1121-0499-P5

LQFP/TQFP 208, 256 28mm (1.10”) 28mm (1.10”) 1.4mm 2.0mm 1224-2005-P1

52, 64, 80, 1/16" Bent Chisel, Long Reach 1.60mm (0.063") 1121-0500-P5
QFP 14mm (.551”) 14mm (.551”) 2.7mm 3.2mm 1124-2006-P1
100
52, 64, 80,
QFP 14mm (.551”) 14mm (.551”) 2.7mm 3.9mm 1124-2007-P1
100 1/16" Chisel, Extended Reach 1.60mm (0.063") 1121-0533-P5
64, 80, 100,
QFP 14mm (.551”) 20mm (.788”) 2.7mm 3.2mm 1124-2008-P1
128
64, 80, 100, Angled Mini-Wave 2.40mm (0.09") 1121-0610-P5
QFP 14mm (.551”) 20mm (.788”) 2.7mm 3.9mm 1124-2009-P1
128
120, 128,
QFP 28mm (1.10”) 28mm (1.10”) 3.4mm 3.9mm 1124-2010-P1
144, 160, 208
1/64" Sharp Bent Conical 0.40mm (0.016") 1121-0830-P5
QFP 160 28mm (1.10”) 28mm (1.10”) 3.4mm 3.9mm 1124-2011-P1

22 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 23
 PS-90 SMT REMOVAL TIPS SX-90 DESOLDERING TIPS & SOLDER REMOVAL TIPS
TIP SPECIFICATIONS TIP SPECIFICATIONS

TIPS DESCRIPTION TIP SIZE PART NUMBER

TIPS SELECTION One of the most important aspects for successful solder removal is the selection of the proper size tip. There are
5.05mm x 5.08mm several points to keep in mind.
SOIC - 8 (JEDEC) (fig.A) 1121-0390-P1
(0.199" x 0.200")
(fig. A) 1. The Inside Diameter (I.D.) of the tip must be large enough to 2. The Outside Diameter (O.D.) of the tip must be slightly
fit over the lead, while providing sufficient room so that air and smaller than the diameter of the pad to prevent tip contact to the
5.05mm x 8.99mm
SOIC - 14 (JEDEC) (fig.A) 1121-0391-P1 solder can be drawn through the tip. board laminate and minimize the possibility of damage.
(0.199" x 0.354")

5.05mm x 10.2mm TIPS DESCRIPTION DIAMETER PART NUMBER

SOIC - 16 (JEDEC) (fig.A) 1121-0392-P1
(0.199" x 0.404")
Thermo-Drive 0.76mm (0.030”) I.D. x 2.03mm (0.080”) O.D. 1121-0930-P5
(fig. B)
3.56mm x 2.03mm Thermo-Drive 1.02mm (0.040”) I.D. x 2.29mm (0.090”) O.D. 1121-0931-P5
Chip Component (fig.B) 1121-0303-P1
(0.14" x 0.08")
Thermo-Drive 1.52mm (0.060”) I.D. x 3.05mm (0.120”) O.D. 1121-0932-P5
(fig. C) 19.333mm x 8.1mm
TSOP (fig.C) 1121-0403-P1 Thermo-Drive 2.29mm (0.090”) I.D. x 5.1mm (0.200”) O.D. 1121-0933-P5
(0.76" x 0.32")

Thermo-Drive 4mm (0.16”) I.D. x 5.1mm (0.200”) O.D. 1121-0951-P5

Flat Blade Tip A = 7.6mm (0.3") 1121-0512-P1
Thermo-Drive, Flathead (0.050”) x (0.090”) I.D. x (0.110”) x (0.190”) O.D. 1121-0934-P5

Extended Reach Thermo-Drive 0.78mm (0.030”) I.D. x 2.29mm (0.090”) O.D. 1121-0935-P5
Flat Blade Tip A = 10.2mm (0.4") 1121-0514-P1
Extended Reach Thermo-Drive 1.02mm (0.040”) I.D. x 2.54mm (0.10”) O.D. 1121-0936-P5

Extended Reach Thermo-Drive 1.52mm (0.060”) I.D. x 3.05mm (0.120”) O.D. 1121-0937-P5
Flat Blade Tip A = 12.7mm (0.5") 1121-0473-P1

ThermoMax 0.76mm (0.030”) I.D. x 1.91mm (0.075”) O.D. 1121-0938-P5

Flat Blade Tip A = 17.8mm (0.7") 1121-0416-P1 ThermoMax 1.02mm (0.040”) I.D. x 2.20mm (0.085”) O.D. 1121-0939-P5

ThermoMax 1.52mm (0.060”) I.D. x 2.69mm (0.106”) O.D. 1121-0940-P5

Flat Blade Tip A = 20.3mm (0.8") 1121-0497-P1

Precision 0.50mm (0.020”) I.D. x 1.79mm (0.070”) O.D. 1121-0941-P5

Precision 0.76mm (0.030”) I.D. x 2.03mm (0.080”) O.D. 1121-0942-P5

Flat Blade Tip A = 25.4mm (1.0") 1121-0448-P1
Precision 1.02mm (0.040”) I.D. x 2.29mm (0.090”) O.D. 1121-0943-P5

Precision 1.52mm (0.060”) I.D. x 2.79mm (0.110”) O.D. 1121-0944-P5

Precision 0.635mm (0.025”) I.D. x 1.39mm (0.055”) O.D. 1121-0949-P5

Precision 0.635mm (0.025”) I.D. x 1.14mm (0.045”) O.D. 1121-0950-P5

Flo-D-Sodr 1.52mm (0.060") I.D. X 4.78mm (0.188") O.D. 1121-0945-P5

Flo-D-Sodr, Precision 0.50mm (0.020") I.D. X 1.78mm (0.070") O.D. 1121-0946-P5

Flo-D-Sodr, Precision 0.50mm (0.020") I.D. X 1.78mm (0.070") O.D. 1121-0947-P5

Flo-D-Sodr, Precision 1.02mm (0.040") I.D. X 2.29mm (0.090") O.D. 1121-0948-P5

Not suitable for use with SX-70 or SX-80

24 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 25
 TT-65 SMT REMOVAL TIPS & HOT JET NOZZLES PRODUCT PAGE
TIP SPECIFICATIONS FOR A COMPLETE PRODUCT LISTING CONTACT PACE OR VISIT www.paceworldwide.com

TT-65 SMT REMOVAL TIPS PACE provides innovative solutions, products and training for the assembly, rework, repair and testing of printed circuit boards.
PACE’s unique capabilities and evolving vision have provided universal solutions to thru-hole and surface-mount assembly and rework
CHIP REMOVAL TIPS DESCRIPTION TIP SIZE PART NUMBER problems for the most advanced electronics. Our strong commitment and history of achievement has resulted in an unparalleled range
1121-0514-P1
of Assembly, Repair and Fume Extraction systems to meet your company’s needs whether working to ISO-9000, industrial, military or
SOIC, SOJ, SIMMs A=10.2mm (0.4")
your own internal specifications. Whatever the challenge, PACE stands ready to provide the best, cost-effective solution for you.
SOIC, SOJ, SIMMs A=12.7mm (0.5") 1121-0473-P1

SOIC, SOJ, SIMMs A=17.8mm (0.7") 1121-0416-P1

ST SYSTEMS ST 30 ST 50ST 50 ST 70 ST 70 ST 100 ST 115
ST 115
SOIC, SOJ, SIMMs A=20.3mm (0.8") 1121-0497-P1
PACE’s new ST systems offer the most
innovative control technology ever
SOIC, SOJ, SIMMs A=25.4mm (1.0") 1121-0448-P1 developed - IntelliHeat. ST systems are
capable of providing the widest range
Chip Component A=0.76mm (0.03") 1121-0398-P1 of applications and flexibility by
simply adding additional handpieces.
Regardless if you are a small or
Chip Component A=2.0mm (0.08") 1121-0313-P1
large shop, ST systems are the right
answer for you!
Chip Component A=4.1mm (0.16") 1121-0399-P1

Chip Component, Small SOIC A=6.4mm (0.25") 1121-0401-P1 FUME EXTRACTION ARM-EVAC 105 ARM-EVAC 250 FUMEFLO WORKTABLE ARM-EVAC 50
PACE’s Fume Extraction Systems
Thin-Walled Chip Component A=0.76mm (0.03") 1121-0520-P1 feature the latest advancements in
filter condition monitoring and process
Thin-Walled Chip Component A=2.0mm (0.08") 1121-0521-P1 control as well as cost effective
solutions. A variety of collection
accessories are available.
1/64" Angled Fine Point Conical A=0.43mm (0.017") 1121-0517-P1

PLCC REMOVAL TIPS DESCRIPTION TIP SIZE A x B PART NUMBER

PLCC-20 6.86mm x 6.86mm (0.27" x 0.27") 1121-0316-P1 MBT/PRC SYSTEMS MBT 350 PRC 2000
PACE offers a broad range of rework
PLCC-28 9.4mm x 9.4mm (0.37" x 0.37") 1121-0317-P1 and repair products to meet all your
repair needs. Whether you are
PLCC-32 12.2mm x 9.65mm (0.48" x 0.38") 1121-0352-P1 replacing a surface mount component,
repairing a multi-layer printed circuit
board, or making a plated thru-hole
PLCC-44, PQFP-84 14.5mm x 14.5mm (0.57" x 0.57") 1121-0318-P1 repair.

PLCC-52, PQFP-100 17.0mm x 17.0mm (0.67" x 0.67") 1121-0319-P1

PLCC-68, PQFP-132 21.9mm x 21.9mm (0.86" x 0.86") 1121-0320-P1 THERMOFLO SYSTEMS TF 1700 TF 2700
TF 2700 XR 3000
XR 3000
PACE’s family of ThermoFlo products
PLCC-84, PQFP-160 26.9mm x 26.9mm (1.06" x 1.06") 1121-0321-P1 offer complete solutions from simple
surface mount removal and installation
to delicate BGA and CSP rework.
PACE’s new inspection systems feature
X-Ray and endoscopic technology
TT-85 HOT JET NOZZLES to really “SEE” the results of your
processes.

TIPS DESCRIPTION TIP SIZE PART NUMBER

1259-0129-P1
CONVECTIVE & PRE-HEAT ST 300 ST 350 ST 525 ST 450
Round Nozzle 1.5mm (.06”) Inner diameter
PACE’s new family of hot air
rework systems are ideal for all
SMT applications. A wide range of
product features are available to
Round Nozzle, Bent 60 degrees 1.5mm (0.6”) Inner diameter 1259-0130-P1
meet your specific needs. They can
be easily upgraded by adding one
of our powerful preheaters and/or
PCB holders.
6.1mm x 1.9mm (.24” x .074”)
Flat Jet Nozzle 1259-0131-P1
Inner flow dimensions

26 MORE THAN 50 YEARS OF INDUSTRY LEADERSHIP SOLUTIONS FOR THE ELECTRONICS INTERCONNECTION PROCESS 27