Product Specification G190EAN01.

0
AU OPTRONICS CORPORATION

! " Preliminary Specification

# " Final Specification

Module 19.0” SXGA Color TFT-LCD

Model Name G190EAN01.0

Checked &
Customer Date Date
Approved by

Vito Huang 5/ 9, 2013

Approved by Prepared by

Ginger Lin 5/ 9, 2012

Audio-Video Business Unit /

Note: This Specification is subject to
AU Optronics corporation
change without notice.

document version 0.3 1/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

Record of Revision

Version & Date Page Old Description New Description

0.1 2012/05/29 All Frist Edition for Customer
4 Add “Handling Precautions Item 13)”
Optical ResponseTime [msec]: Optical ResponseTime [msec]:
TBD (Typ, on/off) 25 (Typ, on/off)
5
Power Consumption[Watt]: Power Consumption [Watt]:
LED: 17.28 (W) + LVDS: 4.7 (W) LED: 14.4 (W) + LVDS: 3.5 (W) (typ)
Optical ResponseTime [msec] : Rising:
Typ.13; Max. 18
Optical ResponseTime [msec]: TBD
Falling: Typ.12; Max. 17
Rising + Falling: Typ.25; Max.35
6
Color/ Chromaticity Coordinates: TBD Update Color/ Chromaticity Coordinates
Contrast Ratio Min. 800 Contrast Ratio Min. 700
Flicker [dB]: Max. -20dB Delete
9 Note 7: Subchecker Pattern Delete
0.2 2012/11/8 ICC: Typ. 0.94; Max. 1.1; Condition: ICC: Typ. 0.7; Max. 0.9; Condition:
Vin=5V, All Black Pattern, at 60Hz Vin=5V, 2dot checker Pattern, at 60Hz

IRush: Typ. 2.1; Max.2.5 IRush: Typ. 2.7; Max.3.4

13
PCC: Typ. 4.7; Max. 5.5; Condition: PCC: Typ. 3.5; Max. 4.5; Condition:
Vin=5V, All Black Pattern, at 60Hz Vin=5V, 2dot checker Pattern, at 60Hz

Note 1: The H-Stripe pattern Note 1: The 2dot checker Pattern

VCC: Min.; Typ. 12; Max. VCC: Min. 10.8; Typ. 12.0; Max.13.2
IVCC: Typ. 1.44; Max.1.70 IVCC: Typ. 1.2; Max.
15
PVCC: Typ. 17.28; Max.20.4 PVCC: Typ. 14.4; Max.15.8
Irush LED:Typ. TBD; Max.TBD Irush LED: Typ. 1.7; Max.2.1
25 Add Note 3
27~28 Update Drawing
Add “Analog control voltage: 0~3.3V”
15
Add “Note 6”
0.3 2013/5/9 22 Update Power Sequence Timing chart
Update “Dimming (or Analog Control
24 Pin 9 “Dimming“
Voltage 0~ 3.3V)”

document version 0.3 2/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

Contents

1. Handling Precautions .................................................................................................................. 4

2. General Description ..................................................................................................................... 5
2.1 Display Characteristics ........................................................................................................................ 5
2.2 Optical Characteristics......................................................................................................................... 6
3. Functional Block Diagram.........................................................................................................10
4. Absolute Maximum Ratings......................................................................................................11
4.1 Absolute Ratings of TFT LCD Module ............................................................................................. 11
4.2 Absolute Ratings of Backlight Unit ................................................................................................... 11
4.3 Absolute Ratings of Environment ...................................................................................................... 11
5. Electrical characteristics ..........................................................................................................13
5.1 TFT LCD Module ............................................................................................................................. 13
5.2 Backlight Unit.................................................................................................................................... 15
6. Signal Characteristic .................................................................................................................16
6.1 Pixel Format Image ........................................................................................................................... 16
6.2 The Input Data Format ...................................................................................................................... 17
6.4 Interface Timing................................................................................................................................. 20
6.5 Power ON/OFF Sequence................................................................................................................. 22
7. Connector & Pin Assignment ...................................................................................................23
7.1 TFT LCD Module ............................................................................................................................. 23
7.2 Backlight Unit.................................................................................................................................... 24
8. Reliability Test ............................................................................................................................25
9. Shipping Label and Packaging.................................................................................................26
9.1 Shipping Label................................................................................................................................... 26
9.2 Packaging .......................................................................................................................................... 26
10. Mechanical Characteristic ......................................................................................................27

document version 0.3 3/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

1. Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of LED light bar edge. Instead, press at the far ends of
LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or
UL1950), or be applied exemption.
13) Avoid stressing front bezel position when doing mechanical design.

document version 0.3 4/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

2. General Description
G190EAN01.0 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD panel, a driver circuit,
and a backlight system. The screen format is intended to support the SXGA (1280(H) x 1024(V)) screen and
16.7M colors. All input signals are 2-channel LVDS interface compatible.

2.1 Display Characteristics

The following items are characteristics summary on the table under 25 oC condition:

Items Unit Specifications

Screen Diagonal [mm] 482.6 (19.0" )
Active Area [mm] 376.32 (H) x 301.06 (V)
Pixels H x V 1280(x3) x 1024
Pixel Pitch [mm] 0.294 (per one triad) x 0.294
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode Normally Black
2
White Luminance [cd/m ] 300 (center, Typ) @ 80mA
Contrast Ratio 1000 : 1 (Typ)
Optical ResponseTime [msec] 25 (Typ, on/off)
Nominal Input Voltage VDD [Volt] +5.0 V

Power Consumption [Watt] LED: 14.4 (W) + LVDS: 3.5 (W) (typ)

Weight [Grams] 1600 (TYP)

Physical Size (H x V x D) [mm] 396 (H) x 324 (V) x 17.0 (D) (Typ)
Electrical Interface Dual channel LVDS
Surface Treatment Anti-Glare treatment
Support Color 16.7M colors
Temperature Range
Operating [oC] 0 to +50
Storage (Non-Operating) [oC] -20 to +60
RoHS Compliance RoHS Compliance

document version 0.3 5/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

2.2 Optical Characteristics

The optical characteristics are measured under stable conditions at 25! (Room Temperature):

Item Unit Conditions Min. Typ. Max. Note

Horizontal (Right) 75 89
-
CR = 10 (Left) 75 89
Viewing Angle [degree] 1
Vertical (Up) 75 89
-
CR = 10 (Down) 75 89

Luminance Uniformity [%] 9 Points 75 80 - 2, 3

Rising - 13 18
Optical Response Time [msec] Falling - 12 17 4, 6

Rising + Falling -- 25 35

Red x 0.601 0.651 0.701

Red y 0.292 0.342 0.392

Green x 0.269 0.319 0.369

Color / Chromaticity Green y 0.567 0.617 0.667
Coordinates 4
(CIE) Blue x 0.095 0.145 0.195

Blue y 0.010 0.060 0.110

White x 0.263 0.313 0.363

White y 0.279 0.329 0.379
White Luminance
(At LED= 80mA) [cd/m2 ] 240 300 - 4

Contrast Ratio 700 1000 - 4

Cross Talk (At 60Hz) [%] - - 1.5 5

document version 0.3 6/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

Note 1: Definition of viewing angle, measured by ELDIM (EZContrast 88)

Viewing angle is the measurement of contrast ratio"10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows;
90° (#) horizontal left and right and 90° ($) vertical, high (up) and low (down). The measurement direction
is typically perpendicular to the display surface with the screen rotated about its center to develop the desired
measurement viewing angle.

Note 2: 9 points position

90 % 50 % 10 %

10 %

50 %

90 %

Note 3: The luminance uniformity of 9 points is defined by dividing the maximum luminance values by the
minimum test point luminance. And measured by TOPCON SR-3
Minimum Luminance of 9 points
!W9 =
Maximum Luminance of 9 points

document version 0.3 7/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

Note 4: Measurement method

The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after
lighting Backlight for 30 minutes in a stable, windless and dark room. %

Photo detector

Field=2!

50 cm

LCD Panel TFT-LCD Module

Center of the screen

Note 5: Definition of Cross Talk (CT) and measured by TOPCON SR-3

CT = | YB – YA | / YA ! 100 (%)

Where

YA = Luminance of measured location without gray level 0 pattern (cd/m2)

YB = Luminance of measured location with gray level 0 pattern (cd/m2)

document version 0.3 8/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

Note 6: Definition of response time, measured by WESTAR TRD-100A

The output signals of photo detector are measured when the input signals are changed from “Full Black” to
“Full White” (rising time), and from “Full White” to “Full Black” (falling time), respectively. The response time
is interval between the 10% and 90% of amplitudes. Please refer to the figure as below.

% Tr F TrR

100
90
Optical
White Black White
response
10
0

document version 0.3 9/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

3. Functional Block Diagram

The following diagram shows the functional block of the 19.0 inches Color TFT-LCD Module:

ASIC G1024

Timing
LVDS Controller TFT-LCD
Connector

LVDS 1280*(3)*1024
Receiver
RSDS Pixels
Transmitter
X-Driver IC
+ 5V G1

D1 D3840

LED B/L
DC/DC Gamma
Converter Correction
(Integrate
level shift)

DC POWER
LED driver

I/F PCB Interface:

FI-XB30SSL-HF15 / MSBKT2407P30HB

Mating Type:
FI-X30HL (Locked Type)
FI-X30H (Unlocked Type)

document version 0.3 10/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

4. Absolute Maximum Ratings

Absolute maximum ratings of the module are as following:

4.1 Absolute Ratings of TFT LCD Module

Item Symbol Min. Max. Unit Conditions

Logic/LCD Drive
VDD -0.3 +5.5 [Volt] Note 1, 2
Voltage

4.2 Absolute Ratings of Backlight Unit

Item Symbol Min. Max. Unit Conditions

LED Power Current Iled - 1.7 [A] rms Note 1, 2

4.3 Absolute Ratings of Environment

Item Symbol Min. Max. Unit Conditions

Operating Temperature TOP 0 +50 [oC]
Operation Humidity HOP 5 90 [%RH]
Note 3 & 4
Storage Temperature TST -20 +60 [oC]
Storage Humidity HST 5 90 [%RH]

document version 0.3 11/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

Note 1: With in Ta= 25!

Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).

Operating Range Storage Range

Note 4: Operation Temperature + 60°C is defined as panel surface termperature.

document version 0.3 12/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows:

Symble Parameter Min. Typ. Max. Unit Condition

VCC Logic/LCD Drive Voltage 4.5 5.0 5.5 [Volt] !10%

Vin=5V, 2dot checker
ICC Input Current - 0.7 0.9 [A]
Pattern, at 60Hz

IRush Inrush Current - 2.7 3.4 [A] Note 2

Vin=5V , 2dot checker

PCC VCC Power - 3.5 4.5 [Watt]
Pattern, at 60Hz
Allowable Logic/LCD Drive [mV]
VCCrp - " 300 With panel loading
Ripple Voltage p-p

Note 1: The 2dot checker Pattern is defined as below:

document version 0.3 13/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

Note 2: Measurement conditions:

+5.0V Q3
AO6402
D6 F1
D5
D2 S
VCC
D1

R1 (LCD Module Input)

47K

G
C1
1uF/16V
(High to Low)

D1
D2
D5
D6
Control
Signal R2
Q3
AO6402
G

1K
C3 S
2

+12.0V
SW1
SW MAG-SPST VR1 0.01uF/25V
1

47K

C2
1uF/25V

90% 5.0V

10%
0V
470 us

VDD rising time

document version 0.3 14/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

5.2 Backlight Unit

o
Following characteristics are measured under a stable condition at 25 C (Room Temperature):

Symbol Parameter Min. Typ. Max. Unit Remark

VCC Input Voltage 10.8 12.0 13.2 [Volt]

IVCC Input Current 1.2 [A] 100% PWM Duty

PVCC Power Consumption 14.4 15.8 [Watt] 100% PWM Duty

Irush LED Inrush Current - 1.7 2.1 [A] at rising time=470us

Analog Control Input Voltage 0 - 3.3 V

Dimming Frequency 0.2 20 [kHz]

FPWM Swing Voltage 3 3.3 5 V

Dimming Duty Cycle 10 - 100 %

IF LED Forward Current 80 mA Ta = 25oC

- - - Volt
o
VF LED Forward Voltage - 3.2 3.6 Volt IF =80 mA, Ta = 25 C

- - -
LED Power IF =80 mA, Ta = 25oC
PLED - 13.8 15.6 Watt
Consumption
LED Lifetime 50,000 Hrs IF=80 mA, Ta= 25oC

Note 1: Ta means ambient temperature of TFT-LCD module.

Note 2: VCC, Ivcc, PVCC , Irush LED are defined for LED B/L.(100% duty of PWM dimming)

Note 3: IF, VF , PLED are defined for LED Light Bar.

Note 4: If G190EAN01.0 module is driven by high current or at high ambient temperature & humidity condition. The
operating life will be reduced.
Note 5: LED life means brightness goes down to 50% initial brightness.
Note 6: Two kind types for adjusting brightness: PWM and Analog.

document version 0.3 15/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.

1 2 1279 1280

1st Line R GB R GB R GB R GB

1024th Line R GB R GB R GB R GB

document version 0.3 16/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

6.2 The Input Data Format

Note1: Normally DE mode only. VS and HS on EVEN channel are not used.
Note2: Please follow VESA.
Note3: 8-bit in

document version 0.3 17/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

6.3 Signal Description

The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a
differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be
SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels
while the second LVDS port(RxExxx) transmits even pixels.
PIN # SIGNAL NAME DESCRIPTION
1 RxOIN0- Negative LVDS differential data input (Odd data)
2 RxOIN0+ Positive LVDS differential data input (Odd data)
3 RxOIN1- Negative LVDS differential data input (Odd data)
4 RxOIN1+ Positive LVDS differential data input (Odd data)
5 RxOIN2- Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
6 RxOIN2+ Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
7 VSS Power Ground
8 RxOCLKIN- Negative LVDS differential clock input (Odd clock)
9 RxOCLKIN+ Positive LVDS differential clock input (Odd clock)
10 RxOIN3- Negative LVDS differential data input (Odd data)
11 RxOIN3+ Positive LVDS differential data input (Odd data)
12 RxEIN0- Negative LVDS differential data input (Even data)
13 RxEIN0+ Positive LVDS differential data input (Even data)
14 VSS Power Ground
15 RxEIN1- Negative LVDS differential data input (Even data)
16 RxEIN1+ Positive LVDS differential data input (Even data)
17 VSS Power Ground
18 RxEIN2- Negative LVDS differential data input (Even data)
19 RxEIN2+ Positive LVDS differential data input (Even data)
20 RxECLKIN- Negative LVDS differential clock input (Even clock)
21 RxECLKIN+ Positive LVDS differential clock input (Even clock)
22 RxEIN3- Negative LVDS differential data input (Even data)
23 RxEIN3+ Positive LVDS differential data input (Even data)
24 VSS Power Ground
25 VSS Power Ground
26 NC Do not connect ( for AUO test)
27 VSS Power Ground
28 VCC +5.0V Power Supply
29 VCC +5.0V Power Supply
30 VCC +5.0V Power Supply

document version 0.3 18/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

Note1: Start from left side

Connector

1 30
RxOIN0-

VCC

Note2: Input signals of odd and even clock shall be the same timing.
Note3: Please follow VESA.

document version 0.3 19/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

6.4 Interface Timing

6.4.1 Timing Characteristics

Signal Item Symbol Min Typ Max Unit

Period Tv 1032 1066 1150 Th
Vertical
Active Tdisp(v) 1024 1024 1024 Th
Section
Blanking Tbp(v)+Tfp(v)+PWvs 8 42 126 Th
Period Th 780 844 2047 Tclk
Horizontal
Active Tdisp(h) 640 640 640 Tclk
Section
Blanking Tbp(h)+Tfp(h)+PWhs 140 204 - Tclk
Period Tclk 22.2 18.52 14.81 ns
Clock
Frequency Freq. 45 54 67.5 MHz
Frame Rate Frequency 1/Tv 50 60 75 Hz

Note : DE mode only

document version 0.3 20/28

www.avnet-embedded.eu
 www.avnet-embedded.eu
G190EAN01.0

21/28
Tv
Vsync
PWvs
Hsync
Product Specification

Tfp(v) Tbp(v) Tdisp(v) Th

DE
AU OPTRONICS CORPORATION

N 1 2 3 4 N
Invalid Data Invalid Data
RGB Data
Line Line Line Line Line Line
CLK
Tclk
Hsync
PWhs
Tbp(h) Tfp(h)
DE
Tdisp(h)
6.4.2 Timing Diagram
RGB Data Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
Invalid Data Invalid Data
(Odd) 1 3 5 7 9 11 M-5 M-3 M-1
RGB Data

document version 0.3

Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
(Even) Invalid Data Invalid Data
2 4 6 8 10 12 M-4 M-2 M
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

6.5 Power ON/OFF Sequence

VDD power and LED on/off sequence is as follows. Interface signals are also shown in the chart. Signals
from any system shall be Hi-Z state or low level when VDD is off.

Power Sequence Timing

Power Sequence Timing

Value
Parameter Units
Min. Typ. Max.
T1 0.5 - 10

T2 30 40 50

T3 200 - --

T4 0.5 - 10

T5 10 - -

T6 10 - -

T7 0 - - ms
T8 10 - -

T9 - - 10

T10 110 - -

T11 0 16 50

T12 0 10

T13 1000 - -

document version 0.3 22/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

7. Connector & Pin Assignment

Physical interface is described as for the connector on module.These connectors are capable of
accommodating the following signals and will be following components.

7.1 TFT LCD Module

7.1.1 Connector

Connector Name / Designation Interface Connector / Interface card

Manufacturer JAE / STM

FI-XB30SSLA-HF15 / MSBKT2407P30HB
Type Part Number

FI-X30HL
Mating Housing Part Number
FI-X30H (Unlocked Type)

7.1.2 Pin Assignment

Pin# Signal Name Pin# Signal Name
1 RxOIN0- 2 RxOIN0+
3 RxOIN1- 4 RxOIN1+
5 RxOIN2- 6 RxOIN2+
7 VSS 8 RxOCLKIN-
9 RxOCLKIN+ 10 RxOIN3-
11 RxOIN3+ 12 RxEIN0-
13 RxEIN0+ 14 VSS
15 RxEIN1- 16 RxEIN1+
17 VSS 18 RxEIN2-
19 RxEIN2+ 20 RxECLKIN-
21 RxECLKIN+ 22 RxEIN3-
23 RxEIN3+ 24 VSS
25 VSS 26 NC
27 VSS 28 VCC
29 VCC 30 VCC

document version 0.3 23/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

7.2 Backlight Unit

Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.

Connector Name / Designation LED Connector / Backlight

Manufacturer STM

Type Part Number MS24019R

Mating Type Part Number P24019

7.2.1 Signal for LED connector

Pin # Symbol Pin Description

1 +12V Power +12V
2 +12V Power +12V
3 +12V Power +12V
4 NC NC
5 GND GND
6 GND GND
7 GND GND
8 EN Enable(0V:disable, 5V:Enable)
Dimming PWM; duty 10%~ 100%
9
(or Analog Control Voltage) (Analog Control Voltage 0~3.3V)

document version 0.3 24/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

8. Reliability Test
Environment test conditions are listed as following table.
Items Required Condition Note
o
Temperature Humidity Bias (THB) Ta= 50 C, 80%RH, 300hours
High Temperature Operation (HTO) Ta= 50oC, 300hours
Low Temperature Operation (LTO) Ta= 0oC, 300hours
High Temperature Storage (HTS) Ta= 60oC, 300hours
Low Temperature Storage (LTS) Ta= -20oC, 300hours
Acceleration: 1.5 G
Vibration Test Wave: Random
(Non-operation) Frequency: 10 - 200 - 10 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)

Acceleration: 50 G
Shock Test Wave: Half-sine
(Non-operation) Active Time: 20 ms
Direction: !X," !Y," !Z (one time for each Axis)

Drop Test Height: 60 cm, package test

Thermal Shock Test (TST) -20 oC /30min, 60/ oC 30min, 100 cycles 1
On/Off Test On/10sec, Off/10sec, 30,000 cycles
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec,
9 points, 25 times/ point.
ESD (Electrostatic Discharge) 2
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
9 points, 25 times/ point.

Operation:10,000 ft
Altitude Test
Non-Operation:30,000 ft

Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-20oC to 60oC, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
Note 3:
! Water condensation is not allowed for each test items.
! Each test is done by new TFT-LCD module. Don’t use the same TFT-LCD module repeatedly for
reliability test.
! The reliability test is performed only to examine the TFT-LCD module capability.
! To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity
for 24 hours at least in advance.
! No function failure occurs.

document version 0.3 25/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

9. Shipping Label and Packaging

9.1 Shipping Label
The label is on the panel as shown below:

G190EAN01.0

Note 1: For Pb Free products, AUO will add for identification.

Note 2: For RoHS compatible products, AUO will add for identification.

Note 3: For China RoHS compatible products, AUO will add for identification.
Note 4: The Green Mark will be presented only when the green documents have been ready by AUO Internal
Green Team.

9.2 Packaging

document version 0.3 26/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

10. Mechanical Characteristic

document version 0.3 27/28

www.avnet-embedded.eu
 Product Specification G190EAN01.0
AU OPTRONICS CORPORATION

document version 0.3 28/28

www.avnet-embedded.eu