Technology FP5139

BOOST CONVERT CONTROL IC

GENERAL DESCRIPTION

The FP5139 is a boost topology switching regulator control IC for battery-used applications
field. The FP5139 includes a totem-pole single output stage for driving NPN transistor or
N-MOS, high precision reference (0.5V) for comparing output voltage with feedback amplifier,
an internal dead-time control for controlling the minimum duty cycle, programmable soft start
with short circuit protection function and logic level control for operating mode or standby
mode.

FEATURES
˙Wide supply voltage operating range: 1.8 to 15V
˙Reference voltage precision: 4%
˙Low current consumption: Operation Mode 5.5mA
Standby-by Mode 1µA
SOP8
˙High speed oscillator frequency: 1MHz max.
˙Programmable Soft Start function (SS)
˙Short Circuit Protection function(SCP)
˙Totem-pole output with adjustable on/off current
(for NPN transistors or n-channel MOSFET)
˙Logic level control stand-by mode function TS S OP 8
˙Package: SOP8/TSSOP8/MSOP8

TYPICAL APPLICATION
˙Digital Camera MS O P 8
˙PDA
˙Portable Equipment

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P1/FP5139
 Technology FP5139
FUNCTIONAL BLOCK DIAGRAM

3 7

Reference 0.6V Sawtooth wave

voltage supply oscillator
0.1V
1.25V 0.1V 5

PWM
1 Comp. 30k
36k
+ Output drive
+ + control circuit
Error Amp. +
0.5V 500
DTC 0.6V
0.22V
8

Soft start SCP

6 2 4

MARK VIEW PIN DESCRIPTION

Name No. I/O Description

FB 1 I Error amplifier inverting input pin
1 8 Connected a capacitor
SCP 2 I
Soft start and SCP function pin
2 7 VCC 3 P IC power supply
FP5139

BR/CTL 4 I Output current setting and control pin

3 6 OUT 5 O Totem-pole output
-

GND 6 P IC ground
4 5 Capacitor and resistor connected for
OSC 7 I
the frequency of oscillation
L

COMP 8 O Error amplifier compensation output

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P2/FP5139
 Technology FP5139
ORDER INFORMATION
Part Number Operating Temperature Package Description
FP5139D-LF -10°C ~ +85°C SOP8 Tube
FP5139DR-LF -10°C ~ +85°C SOP8 Tape & Reel
FP5139W-LF -10°C ~ +85°C TSSOP8 Tube
FP5139WR-LF -10°C ~ +85°C TSSOP8 Tape & Reel
FP5139T-LF -10°C ~ +85°C MSOP8 Tube
FP5139TR-LF -10°C ~ +85°C MSOP8 Tape & Reel

IC DATE CODE DISTINGUISH

FP5139
- L
Lead Free
Lot Number
Mass Production Version
Per Half Month
Year

FOR EXAMPLE:
January A (Front Half Month), B (Last Half Month)
February C, D
March E, F ------------And so on

Lot Number is the last two numbers

For Example:
A3311C62
Lot Number

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P3/FP5139
 Technology FP5139
ABSOLUTE MAXIMUM RATINGS
Power supply voltage--------------------------------------------------------------------------- +15V

Output source current------------------------------------------------------------------------- -50mA

Output sink current------------------------------------------------------------------------------ +50mA

Allowable dissipation
SOP8 Ta≦+25℃------------------------------------------------------------ 570mW
MSOP8 Ta≦+25℃----------------------------------------------------------- 400mW
TSSOP8 Ta≦+25℃----------------------------------------------------------- 400mW

Operating temperature--------------------------------------------------------------- -10℃∼+85℃

Storage temperature------------------------------------------------------------------ -55℃∼+125℃

SOP8 Lead Temperature (soldering, 10 sec) ------------------------------------------+260℃

TSSOP8 Lead Temperature (soldering, 10 sec) --------------------------------------+260℃

MSOP8 Lead Temperature (soldering, 10 sec) ---------------------------------------+260℃

260℃ / 10 sec

260℃

+0.23℃ / sec -1.2℃ / sec

210℃
180℃

+3.4℃ / sec

25℃

15s 60s 190s 280s

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P4/FP5139
 Technology FP5139
DC ELECTRICAL CHARACTERISTICS
VCC=2V,TA=25℃
Under Voltage Lock-Out section (U.V.L.O.)
PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Low threshold voltage VLOW -- - - 0.9 V
Upper threshold voltage VUPPER -- 1.1 1.3 1.5 V

Soft Start section (S.S.)

PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Input source current ISS VSCP= 0V -1.5 -1.0 -0.7 μA
Soft start threshold voltage VSST -- 0.8 0.9 1.0 V

Short Circuit Protection section (S.C.P.)

PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Input source current ISCP VSCP= 0V -1.5 -1.0 -0.7 μA
S.C.P. threshold voltage VSCP -- 0.7 0.8 0.9 V

Oscillator section
PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Oscillation frequency f RT=3.0KΩ,CT=270pF 400 500 600 KHz
Frequency change with
∆f / ∆V VCC=2V to 15V - 2 10 %
voltage
Frequency change with
∆f / ∆T Ta = 0℃to 85℃ - 5 - %
temperature

Idle Period Adjustment section

PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
RT=3.0kΩ, CT=270pF,
Maximum duty cycle TDUTY - 92 98 %
VFB=0.8V

Total device section

PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Stand-by current ISTANDBY Pin4 is open or VCC - - 1 µA
Average supply current IAVE RB=390Ω,VCC=0~15V - 5.0 10 mA

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P5/FP5139
 Technology FP5139
DC ELECTRICAL CHARACTERISTICS (Cont.)
Error Amplifier section
PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Input threshold voltage VFB VCOMP=450mV 480 500 520 mV
VT change with voltage ∆VFB / ∆V VCC=2V to 15V - 5 20 mV
VT change with temperature ∆VFB / ∆T Ta = -10℃to 85℃ - 1 - %
Input bias current IB -- -1.0 -0.2 1.0 µA
Voltage Gain Av -- - 100 - V/V
Frequency bandwidth BW Av=0 dB - 6 - MHz
Output voltage Positive VPOS -- 0.78 0.87 -
V
Swing Negative VNEG -- - 0.05 0.2
Output source current ISOURCE - -40 -24 µA
VCOMP=450mV
Output sink current ISINK 24 40 - µA

Output section
PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Output high voltage VOH1 RB=390Ω, IO=-15mA 1.0 1.2 - V
RB=750Ω, IO=-10mA,
Output high voltage VOH2 0.8 1.0 - V
VCC= 1.8V
Output saturation voltage VOL1 RB=390Ω, IO=15mA - 0.1 0.2 V
RB=750Ω, IO=10mA,
Output saturation voltage VOL2 - 0.1 0.2 V
VCC= 1.8V
Output source current IOSOURCE RB=390Ω, Vo=0.9V - -40 -20 mA
Output sink current IOSINK RB=390Ω, Vo=0.3V 30 40 - mA
Internal pull-down resistor RO -- 20 30 40 kΩ

Output Current Setting / Control section

PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Pin voltage VBR RB=390Ω 0.15 0.22 0.3 V
Input off condition IOFF -- -20 - 0 µA
Input on condition ION -- - - -45 µA
Pin current range IBR -- -1.8 - -0.1 mA

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P6/FP5139
 Technology FP5139
TYPICAL CHARACTERISTICS
Supply voltage vs. Supply current Supply voltage vs. Input threshold voltage
12 1.2
Ta=25 ℃ Ta=25 ℃
RB=390Ω
10 1.0

Input threshold voltage Vt(V)

8 0.8
Supply current(mA)

6 0.6

4 0.4

2 0.2

0 0
0 4 8 12 16 20 0 4 8 12 16 20

Supply voltage Vcc(V) Supply voltage Vcc(V)

Figure 1 Figure 2

Ambient temperature vs. Input threshod

voltage variation ratio High level output
30
1.2
V Vt(%)

Vcc=2V
Vcc=2V
10 RB=390Ω
1.0 Ta=25 ℃
High level output voltage Vout(V)
Input threshold voltage variation ratio

5
0.8

0
0.6

-5
0.4

-10
0.2

-15
-25 0 25 50 75 100 0
0 -10 -20 -30 -40 -50
Ambient Temperature Ta (℃)
High level output current Iout(mA)
Figure 3
Figure 4

Low level output BR/CTL pin current vs. Output source current
600 -60
Vcc=2V
Vcc=2V
RB=390
Vout=0.9V
500 Ta=25℃ -50 Ta=25 ℃
Low level output voltage Vout(V)

Output source current Iout(mA)

400 -40

300 -30

200 -20

100 -10

0 0
0 20 40 60 80 100 0 -0.4 -0.8 -1.2 -1.6 -2.0

Low level output current Iout(mA) BR/CTL pin current IBR(mA)

Figure 5 Figure 6

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P7/FP5139
 Technology FP5139
TYPICAL CHARACTERISTICS (Cont.)
BR/CTL pin current vs. BR/CTL pin voltage BR/CTL pin current vs. Supply current
600 6.0
Vcc=2V Vcc=2V
Ta=25℃ Ta=25℃
500 5.0
BR/CTL pin voltage VBR(mV)

Supply current Icc(mA)

400 4.0

300 3.0

200 2.0

100 1.0

0 0
0 -0.4 -0.8 -1.2 -1.6 -2.0 0 -20 -40 -60 -80 -100

BR/CTL pin current IBR(mA) BR/CTL pin current IBR(uA)

Figure 7 Figure 8

TRIANGLE OSCILLATOR FREQUENCY Supply voltage vs. Frequency variation ratio

VS 15
TIMING RESISTANCE
1M CT=270PF
Vcc=2V 10 RT=3.0KΩ
Ta=25℃ Ta= 25℃
Frequency variation ratio △f f(%)
Oscillation frequency f osc(Hz)

CT = 100 pF 5

100 K
0

CT = 1000 pF
-5
10 K
-10

CT = 10000 pF
-15
0 4 8 12 16 20
2K
1K 4K 10 K 40 K 100 K 400 K 1M
Supply voltage Vcc(V)

Timing resistor Rt(Ω) Figure 10

Ambient temperature vs. Frequcney variation ratio

30

Vcc=2V
CT=270PF
10
RT=3.0KΩ
Frequency variation ratio △f f(%)

- 5

-10

-15
-25 0 25 50 75 100

Ambient Temperature Ta (℃)

Figure 11

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P8/FP5139
 Technology FP5139
DETAILED DESCRIPTION
Voltage reference
A 1.25V regulator operating from VCC is used to power the internal circuitry of the FP5139. An
internal resistive divider provides 0.5V reference for the error amplifier, Soft-start (typ. 0.9V)
and SCP (typ. 0.8V) circuits.

Error amplifier
The error amplifier compares a sample of the dc-dc converter output voltage to the 0.5V
reference and generates an error signal for the PWM comparator. Output voltage of dc-dc
converter is setting with the resistor divider using the following expression (see fig12):

 R1 
Vout = 1 +  ∗ 0.5
 R2 
VOUT

R1

1
36K
Error
Amplifier
R2

0.5V 500

FP5139
8

C1

Figure 12. Error Amplifier with Feedback resistance divider

Oscillator
The oscillator frequency can be set between 20KHz and 500KHz by connecting a resistor and
a capacitor at OSC pin of FP5139 to ground. The oscillator frequency can be determined by
using the graph shown in Figure 9.
The oscillator output is a sawtooth wave with a minimum value of approximately 0.1V and a
maximum value of approximately 0.6V. The PWM comparator compares the oscillator voltage
with error amplifier output voltage; internal DTC voltage (typ. 0.6V) and soft start setting
voltage. When the sawtooth wave voltage is low than above three-output voltage, the output of
FP5139 is high (Turn on NPN transistor or NMOS).

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P9/FP5139
 Technology FP5139
Under voltage lockout (UVLO)
The under voltage lockout circuits turn the output off and whenever the supply voltage drops
too low (approximately 0.9V at 25℃) for proper operation. A hysteresis voltage of 200mV
eliminates false triggering on noise and chattering.

Soft Start/ Short-circuit protection (S.S. / S.C.P.)

The soft start is functional after power on, and the interval of soft start time is determined by a
capacitor connected to SCP pin (pin 2). When soft start function finished, the internal soft start
voltage is setting high, but external SCP pin is setting low in order to change to short circuit
detection / protection function.
The time of soft start is following expression:
Tss = 0.35 ∗ C [µF ]
The short circuit protection is functional due to a heavy loading drop and output of error
amplifier (COMP pin) is maintain a VPOS (typ. 0.87V), the capacitor is charged until SCP
threshold voltage (typ. 0.8V), then FP5139 output is disable (internal pull-low) and the
capacitor is discharged to low.
The time of short circuit protection is following expression:
Tscp = 0.8 ∗ C [µF ]

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P10/FP5139
 Technology FP5139
Output transistor
The FP5139 has a totem-pole transistor with a 40mA source/sink current rating to drive an
external NPN transistor or NMOS directly. The driving current capability depends on a resistor
R that is connected to BR/CTL pin (Pin4) of FP5139. (see fig. 14)

FP5139
4
BR/CTL

R1

Control R2
Q1

Figure 13. Output transistor driving control circuit

BR/CTL pin can also use to control the output of FP5139 for disable or enable function of
system.

Control Pin Q1 BR/CTL Pin Output Transistor Function Mode

Low Off Open Disable Stand-by
High On Bias Current Enable Operation

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P11/FP5139
 Technology FP5139
APPLICATION NOTE (1)

L1 33uH SCD34
Vin +2.5V D1
Vout +9V/1A

IC1
R1
FB COMP R2

51k 1%
SCP OSC C1
0.027uF
C2
VCC GND

2
R3 0 Q2
C7 1 C8 C4
BR/CTL OUT
220uF/25V 0.1uF 100uF/35V

3
FP5139
C5 R4
R6
0.1uF 1k R5 C6
3k 3k 1%
Q1 470pF
3904

ON/OFF Socket
Vin
R7 4.7k
1
2
SW1

Figure 14. DC12V to DC24V Boost Regulator

L1 20uH SCD34
Vin +2.5V ~ +6V C9 D1
Vout +3.3V

IC1 10u
R1
FB COMP R2

5.6k 1%
SCP OSC C1
0.027uF
C2
VCC GND L2
2

R3 0 Q2 20uH
C7 1 C8 C4
BR/CTL OUT
220uF/25V MOSFET N GDS 0.1uF 100uF/35V
3

FP5139
C5 R4
R6
0.1uF 1k R5 C6
3k 1k 1%
Q1 470pF
3904

ON/OFF Socket
Vin
R7 4.7k
1
2
SW1

Figure 15. DC2.5V~DC6V to DC3.3V SEPIC Regulator

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P12/FP5139
 Technology FP5139
APPLICATION NOTE (2)

D1 BAT54S/SOT_0 Q1
Q2 Vout3
C1 0.1uF C2 0.1uF NPN BEC MOSFET P
3 2 2 3

3
Vout2
Q3 1 D2 C3
1uF R1 C4
R2 BAT54S/SOT_0 R 1uF

1
R C5

1
R3 1uF R4
R
R5

2
R6 R
R7 R
C6 R
1uF D3

2
3

1 C8
R8 1 D4 TL431 1uF
R
TL431

3
2

R9 Q4

NPN
L1 33uH L2 33uH R10
Vin D5 SCD34 Vout1 C9 R
1uF

IC1
R11
1 8
FB COMP R12

2 7 51k 1%
SCP OSC C10
0.1uF
3 6 C11
VCC GND

2
Vot Socket2 Vin Socket
Vout2 Vin R13 0 Q5
C12 4 5 1 MOSFET N GDS C13 C14 C15
1 1 BR/CTL OUT
2 2 220uF/6.3V R14 100uF 0.1uF 100uF
C16 C7 FP5139 3
CON1 CON2 1k
0.1uF 0.1uF
R15
Vot Socket3 Vot Socket1 R16 C17
Vout3 Vout1 3k 3k 1%
Q6 470pF
1 1 NPN 3904
2 2
CON3 CON4

ON/OFF Socket
Vin
R17 4.7k
1
2
SW1

Figure 16. Charge Pump DC-DC Converter Circuits

APPLICATION NOTE (3)

R9 R8
V2

56K 1.8K
R10 R11
FB V3

33K 5.1K D2 BAT54HT1 L2 33uH

R12 V1 +15V
3.3K (R9+R8)=17.48*R12
0.66*(R8+R9)=(R10+R11) + C8 + C9
100uF/25V 47uF/16V
D3
VCC F1 L1 18uH T1
L3
Ｖ
２

＋
５
Ｖ

4 6 33uH

FUSE C2 C1 5
+ R7 C7 7 + C10 + C11
104 470pF 100uF/16V 47uF/16V
330uF 1 BAT54RCLT1
8
2 D4
D6
8.2 9 L4 33uH
U1 V3 +3.3V
1 8 COMP 3 10
FB COMP + C12 + C13
SCP 2 7 C5 100uF/16V 47uF/16V
SCP Cosc CLS12 BAT54RCLT1
0.1uF C6
3

C4 3 6
VCC GND
0.47uF CTL 4 5 1 Q3 L5 33uH
CTL OUT AP2304 V4 -7.5V
R6 0
2

FP5139
R5 D5 BAT54HT1
220 + C14 + C15
100uF/16V 47uF/16V
R1
Q2
2N3904 R4
ON / OFF 33K C3 R3
C16 R2 270pF 3K
1nF 10K

Figure 17. Flyback Multi-output DC-DC Converter Circuits

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P13/FP5139
 Technology FP5139
TIMING WAVEFORM

COMP pin Voltage

Reference input for
SCP Comparator

Idle period setting voltage

Oscillator waveform

Soft-start setting voltage

OUT pin waveform

SS/SCP pin waveform

Output tpe
Soft-start
ts Short
Output Short Circuit
Circuit

Control pin voltage Short Circuit Protection

IC Shutdown

Figure 18. FP5139 Timing Diagram

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P14/FP5139
 Technology FP5139
PACKAGE OUTLINE
SOP8
0.008typ.

0.015X45
H
E

0.16typ
0.050typ

θ°
D

L
A

SEATING PLANE
A1

0.004max

SYMBOLS MIN MAX

A 0.053 0.069
A1 0.004 0.010
D 0.189 0.196
E 0.150 0.157
H 0.228 0.244
L 0.016 0.050
θ° 0 8
NOTE:
1. JEDEC OUTLINE:MS-012 AA
2. DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE
BURRS.MOLD FLASH,PROTRUSIONS AND GATE BURRS SHALL NOT
EXCEED .15mm (.0.06in) PER SIDE
3. DIMENSIONS “E” DOES NOT INCLUDE INTER-LEAD FLASH,OR PROTRUSIONS.
INTER-LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED .25mm (.0.10in) PER
SIDE.

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P15/FP5139
 Technology FP5139
MSOP8
8 5

E1

E
“A”

1 4
0.30 0.65 BSC

GAUEGE PLANE
θ° SEATING PLANE
D

0.25
L
0.15 TYP

L1
A2
A
A1

0.05

SYMBOLS MIN MAX

A - 1.10
A1 0.00 0.15
A2 0.75 0.95
D 3.00 BSC
E 4.90 BSC
E1 3.00 BSC
L 0.40 0.80
L1 0.95 REF
θ° 0 8
NOTE:
1.JEDEC OUTLINE:MO-187 AA
2.DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE
BURRS.MOLD FLASH,PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED 0.15 PER
SIDE
3.DIMENSIONS “E1” DOES NOT INCLUDE INTERLEAD FLASH,OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.25 PER SIDE.
4.DIMENSIONS “0.22” DOES NOT INCLUDE DAMBAR PROTRUSIONS.ALLOWABLE DAMBAR
PROTRUSIONS SHALL BE 0.08 MM TOTAL IN EXCESS OF THE ‘0.22’ DIMENSION AT
MAXIMUM MATERIAL CONDITION.DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS
OF THE FOOT.MINIMIM SPAC BETWEEN PROTRUSION AND ADJACENT LEAD IS 0.07MM.
5.DIMENSIONS “D” AND ‘E1’ TO BE DETERMINED AT DATUM PLANE H

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P16/FP5139
 Technology FP5139
TSSOP8

SYMBOLS MIN NOR MAX

A - - 1.20
A1 0.05 - 0.15
A2 0.96 1.01 1.06
D 2.90 3.00 3.10
E 6.40 BSC
E1 4.30 4.40 4.50
L 0.45 0.60 0.75
Θ° 0 - 8
NOTE:
1.JEDEC OUTLINE:MO-187 AA

2.DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS.MOLD

FLASH,PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE

3.DIMENSIONS “E1” DOES NOT INCLUDE INTERLEAD FLASH,OR PROTRUSIONS. INTERLEAD

FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.25 PER SIDE.

4.DIMENSIONS “0.22” DOES NOT INCLUDE DAMBAR PROTRUSIONS.ALLOWABLE DAMBAR

PROTRUSIONS SHALL BE 0.08 MM TOTAL IN EXCESS OF THE ‘0.22’ DIMENSION AT MAXIMUM

MATERIAL CONDITION.DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OF THE

FOOT.MINIMIM SPAC BETWEEN PROTRUSION AND ADJACENT LEAD IS 0.07MM.

5.DIMENSIONS “D” AND ‘E1’ TO BE DETERMINED AT DATUM PLANE H

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P17/FP5139
 Technology FP5139
PACKING SPECIFICATIONS
BOX DIMENSION
TUBE INSIDE BOX AND CARTON
380mm

FTC Logo
365mm

630mm
BOX
LABEL

230mm
CARTON
LABEL
190mm FTC Logo

INSIDE BOX
TUBE CARTON

TAPE AND REEL INSIDE BOX AND CARTON

380mm

362mm

365mm

342mm FTC label

230mm

50mm
CARTON
LABEL
FTC Logo

Tape & Reel Carton

PACKING QUANTITY SPECIFICATIONS

SOP 8 MSOP8 TSSOP8 SOP 8 MSOP8 TSSOP8
100 80 160
2500 EA / REEL
EA/TUBE EA/TUBE EA/TUBE
100 TUBES / INSIDE BOX 4 INSIDE BOXES / CARTON
4 INSIDE BOXES / CARTON

LABEL SPECIFICATIONS
Tapping & Reel
Feeling Technology Corp.
Product FP5139
Lot No A3311C62
D/C 4Xx-XXL
Q'ty ◎∼◎
無鉛
Lead Free

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P18/FP5139
 Technology FP5139
CARTON

Feeling Technology Corp.

Product Type: FP5139

Lot No: A3311C62
Date Code: 4Xx-XXL
Package Type: SOP-8L
Marking Type: Laser 無鉛
Total Q'ty: 10,000 Lead Free

CARRIER TAPE DIMENSIONS

SOP8
APPLICATION W P E F D D1
+0.3
SOP8 12.0
-0.1
8.0±0.1 1.75±0.1 5.5±0.1 1.55±0.1 1.5+0.25

APPLICATION Po P1 AD Bo Ko t
SOP8 4.0±0.1 2.0±0.1 6.4±0.1 5.20±0.1 2.1±0.1 0.30±0.013

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P19/FP5139
 Technology FP5139
REEL DIMENISIONS

APPLICATION MATERIAL A B C D T1 T2
PLASTIC REEL
SOP8 330±0.1 62±1.5 12.75+0.15 2+0.6 12.4+0.2 2.0+0.2
(WHILE)

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P20/FP5139
 Technology FP5139
CARRIER TAPE DIMENSIONS
MSOP8

APPLICATION W P E F D D1
MSOP8 12.0±3 8.0 1.75±1.0 5.5±0.5 1.5+0.1 1.50

APPLICATION P0 P1 AD B0 K0 t
MSOP8 4.0±0.1 2.0±0.5 4.20 3.30 1.20 0.30±0.5

(mm)

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P21/FP5139
 Technology FP5139
REEL DIMENISIONS

APPLICATION MATERIAL A B C D T1 T2
PLASTIC REEL
MSOP8 330±1 62±1.5 12.75+0.15 2±0.15 12.4+0.2 16.8-0.4
(WHILE)

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P22/FP5139
 Technology FP5139
CARRIER TAPE DIMENSIONS
TSSOP8

APPLICATION W P E F D D1
TSSOP8 12.0±0.3 8.00 1.75±1.0 5.5±0.05 1.5+0.1 1.50

APPLICATION P0 P1 AD B0 K0 t
TSSOP8 4.00 2.00±0.05 4.20 3.40 1.30 0.30±0.5

(mm)

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P23/FP5139
 Technology FP5139
REEL DIMENISIONS

APPLICATION MATERIAL A B C D T1
PLASTIC REEL
TSSOP8 330 100 13.0+0.5 2±0.5 12.5
(WHILE)

Website: http://www.feeling-tech.com.tw Rev0.2 Nov. 25, 2005

P24/FP5139