Scribd
Upload
54 views2 pages

Procedure For Hot Punching

This document outlines the procedure for hot punching stickers at Siddhivinayak Industries. It describes cleaning and preparing the machine, taking the inspection report and materials, setting sizes on the machine, punching samples, conducting inspections, completing the punching process, handling scrap and finished materials, and safety specifications. The operator is responsible for following the procedure and inspection reports are used to record the process.

Uploaded by

parshuram malvekar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
54 views2 pages

Procedure For Hot Punching

This document outlines the procedure for hot punching stickers at Siddhivinayak Industries. It describes cleaning and preparing the machine, taking the inspection report and materials, setting sizes on the machine, punching samples, conducting inspections, completing the punching process, handling scrap and finished materials, and safety specifications. The operator is responsible for following the procedure and inspection reports are used to record the process.

Uploaded by

parshuram malvekar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

SIDDHIVINAYAK INDUSTRIES

Doc.: Procedure for Hot punching Doc. No. SPI/8.5.1/SOP-01 Page 1 of 2


Issue No: 00 Issue Date: 13.06.2019 Rev. No: 0 Rev. Date: --

PROCEDURE FOR STICKER HOT PUNCHING

1. PURPOSE: To do the hot punching of the material as per the Inspection report and the
specification chart.

2. SCOPE: This procedure as applicable to the functions of die punching machine operator.

3. RESPONSIBILITY: It is the responsibility of the Hot punching machine operator to do work as


per the Inspection report and specification sheet.

4. REFEENCE: Inspection report, Supervisor

5. PROCEDURE:

5.1 Do Machine & Screen Zig cleaning by using dry cloth.


5.2 Clean all Sticker with help of thinner
5.3 Do oiling and greasing to the moving parts.
5.4 Take Inspection report from the supervisor. (Inspection report no. SPI/8.5.1/F-01)
5.5 Take material from the store and check for its size.
5.6 Set size on the cutting machine by referring customer drawings.
a. Set machine for proper Zig
b. Check alignment of press bed and the tool
c. Ensure the punch plate matched properly
d. Punch for the required measurement.
e. Check sample for the proper finish, like bur, damage etc.
5.7 Do inspection for the first piece as per the specifications.
5.8 If Visually & Fitment is ok then start the further punching process and record on the
inspection report
5.9 Do in-process inspection and record after every 4 hours per lot on the Inspection report on
daily basis.
5.10 Check for the cut, damage, bend, dent & surface finish of the jobs. If Jobs is not up to the
mark then reject it and record accordingly.

REVIEWED BY : PRATIK TRIVADI APPROVED BY: PRASAD DALAL


SIDDHIVINAYAK INDUSTRIES
Doc.: Procedure for Hot punching Doc. No. SPI/8.5.1/SOP-01 Page 2 of 2
Issue No: 00 Issue Date: 13.06.2019 Rev. No: 0 Rev. Date: --

PROCEDURE FOR STICKER HOT PUNCHING

5.11 After completion of job handover material to next department. Segregate scrap as well as
produced material, put identification label and keep in the designated area.
5.12 If any problem then contact supervisor.

5.13 SAFETY SPECIFICATION S

a. Ensure surrounding area is clean and free from trip hazards.

b. Make process with safety requirements.

c. Safety precautions should be taken before performing the operation.

d. Refer Job specification for the job operation.

e. Job taken for the process must be properly inspected.

f. Remove wire connections or switch off the mains during any maintenance.

g. Do not put hand or any object in moving parts of machine.

h. Switch of the machine, if any abnormal sound appears

i. Always use safety equipments where ever necessary.

6.0 RECORD:

Sr. Document/ Record Name Doc./ Record No.


1. In-process Inspection Form SPI/8.5.1/F-01
Inspection report Cum In-process Inspection
2. SPI/8.5.1/R-01
Record File

REVIEWED BY : PRATIK TRIVADI APPROVED BY: PRASAD DALAL

You might also like