JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.

4 REPLACEMENT OF MAJOR PARTS

8.4.4 Replacement of LCD Monitor

Replacement of LCD monitor must be made by specialized
service personnel.

For details, refer to Service Manual.

8.4.4.1 Display Unit NCD-4990

Do not touch the LCD screen directly with your fingers.

Do not touch the AR filter directly with your fingers.

Perform the replacement work on a soft cloth to avoid damage to the LCD screen and
other parts.

[Required tools]

• A Phillips screwdriver for 4 mm screws

• A Phillips screwdriver for 6 mm screws

[Disassembly]

1) Remove the tilt fixing handle (standalone type

only).
8
2) Tilt up the screen as much as you can
(standalone type only).

8－ 33
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS

3) Remove the screws (M6) from the four

corners and displace the face cover.

Remove

4) LRemove the LCD operation circuit

cables and remove the face cover.

Remove

5) Remove six M4 screws.

Remove

Remove

8－ 34
 JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS

6) Displace the module and remove the three

cables.
7) Remove the LCD module.
Remove

[Assembly]

1) Tighten the lower three M4 screws halfway.

2) Connect the cables to the LCD module.

3) Align the module to the lower three screws
and insert it downward. Temporary
tightening
4) Check the positions of the two bosses and
ensure that appropriate space is maintained
under the LCD module. Tighten the six
screws evenly.

5) Connect the LCD operation circuit cables

and attach the face cover.
8
6) Tighten the screws at the four corners.
7) Attach the tilt fixing handle.

Positions of the
[Operation Check]
two bosses

1) After completing the replacement

procedures, start the system to make sure that images are displayed properly.
2) Turn the brightness knob to make sure the brightness can be changed between the
minimum and the maximum levels.

8－ 35
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS

8.4.5 Replacement of Backup Battery

Replacement of backup battery must be made by specialized
service personnel.

For details, refer to Service Manual.

A coin-cell battery maintains radar system configuration, date, and time

information while power off condition. Radar system configuration is saving to
non-volatile memory at fixed intervals.

8.4.5.1 About the Battery Alarm

If Battery Low is appeared at the lower-right of the display when start up the
radar system, the battery has not enough time left to live. We recommend to
replace the battery.

If Battery Dead is appeared at the lower-right of the display when start up the
radar system, the battery has no time left to live. There is a necessary to replace
the battery. In This condition, this radar system is restored configuration
information from flash memory and normal operation is available. However, you
turned of the radar system before saving to flash memory, the configuration
information is maybe lost. In this case, you must setup the configuration again.
About disposal of used battery, refer to Section 10.2.

8.4.5.2 How to Replacement of Backup Battery

[Required tools]

• A flat tip screwdriver for 6 mm screws

• A Phillips screwdriver for 4 mm screws
• A flat tip nonconductive screwdriver for 3 mm screws

8－ 36
 JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS

[Disassembly]

1) Remove the four fixing screws to remove

the cover from the display unit (NCD-
4990).

（A flat tip screwdriver for 6 mm screws）

For standalone type NCD-4990 Remove

For tabletop type: NDC-1399-9

Remove

2) Remove the cable connected to the radar

processing circuit board. Remove

The radar processing circuit is the first board

from the left.
8
3) Remove the two fixing screws (M4).
4) Pull out the board to the front.

5) Insert the flat tip nonconductive screwdriver

for adjustment or some stick between the
battery and the battery holder and lift the
battery up.

8－ 37
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS

6) Insert the flat tip nonconductive sscrewdriver

for adjustment or some stick to the location
shown in the figure below and slide the battery
sideways to remove the battery.

[Assembly]

1) Check the polarity of the battery. Make sure

that the battery's positive (+) side is facing up.
2) Slide the battery sideways into the battery
holder.
3) Make sure that the battery is inserted fully.

[Check Item]

1) Check that no error message comes up.

2) Check that the system starts up normally.

[Notes]

8－ 38
 JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS

If you installed the battery with the wrong polarity, remove the battery immediately and
do not use the same battery again.

During the procedures, do not put the battery on any circuit board or conductive item.

To dispose of a used battery, follow the instructions provided in Section 10.2 "DISPOSAL
OF USED BATTERIES".

To disassemble of a used battery, have to use non-conductive tool.

8－ 39
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS

8－ 40
 SECTION 9
TROUBLE SHOOTING AND
AFTER-SALES SERVICE

TROUBLE SHOOTING AND AFTER-SALES SERVICE

9.1 FAULT FINDING .....................................................................................9-1
9.1.1 List of Alarms and other Indications .............................................9-1
9.1.2 Operation Checking ........................................................................9-5
9.1.3 Fuse Checking .................................................................................9-5
9.2 TROUBLE SHOOTING ...........................................................................9-6
9.2.1 Special Parts ....................................................................................9-7
9.2.2 Circuit Block to be Repaired ..........................................................9-8
9.3 AFTER-SALES SERVICE ....................................................................9-14
9.3.1 Keeping period of maintenance parts .........................................9-14
9.3.2 When you Request for Repair ......................................................9-14
9.3.3 Recommended Maintenance ........................................................9-14
 JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING

9.1 FAULT FINDING

In case of semiconductor circuits, it is deemed that there are few cases in which
the used semiconductor devices have inferior quality or performance deterioration
except due to insufficient design or inspection or by other external and artificial
causes. In general, the relatively many causes are disconnection in a high-value
resistor due to moisture, a defective variable resistor and poor contact of a switch
or relay.

Some troubles are caused by defective parts, imperfect adjustment (such as tuning
adjustment) or insufficient service (such as poor cable contact). It will also be
effective to check and readjust these points.

9.1.1 List of Alarms and other Indications

The system automatically recognizes an internal alarm and displays the alarm
message. If an event which is not trouble but must be reported to the operator
occurs, the system notifies the operator of the event.

Error message and alarm are displayed in the lower right of the display. For more
details refer to page2-31 Alarm.

This section gives the list of alarms displayed by the system and other display
lists.
9
Table9-1： List of System Error Message
Message Description
TXRX (SSW Off) Scanner: Safety switch OFF.
TXRX (AZI) Scanner: BP error.
TXRX (HL) Scanner: HL error.
TXRX (MHV) Scanner: Modulator's high voltage alarm.
TXRX (Data) Scanner: No communication, communication mismatched,
checksum error, or collision.
TXRX (Heater) Scanner: Magnetron heater voltage error.
TXRX (Reverse) Scanner: Reverse rotation.

9－ 1
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING

Table9-1： List of System Error Message

Message Description
TXRX (Video) Scanner: VIDEO error.
TXRX (Trigger) Scanner: TRIGGER error..
TXRX (Fan 1) Scanner: FAN 1 error.
TXRX (Fan 2) Scanner: FAN 2 error.
TXRX (Motor) Scanner: Motor current error.
Keyboard (Data) Operation unit: Communication error or checksum error.
Keyboard2 (Data) Second operation unit: Communication error or checksum error.
GYRO I/F (Data) GYRO I/F: No communication or checksum error.
GYRO I/F (GYRO) GYRO I/F: GYRO error (error bit detected).
GYRO I/F (Log) GYRO I/F: Log error (error bit detected).
GPS (Status) GPS status error.
Position (Data) Latitude / longitude data: No communication or data error.
Date (Data) Date data: No communication or data error.
Speed (Log) 1-axis log: No communication or data error.
Speed (2AXW) 2-axis log (speed over water): No communication or data error.
Speed (2AXG) 2-axis log (speed over ground): No communication or data error.
Speed (GPS) GPS speed: No communication or data error.
PROC (Interrupt) Process unit: Interrupt error.
PROC (AZI) Process unit: AZI error.
PROC (HL) Process unit: HL error.Error during interrupt from ASIC1 to
RADAR DSP.
ASIC1 to RADAR VIDEO error.
PROC (Video) Trigger error.
PROC (Trigger) Heading data: No communication or data error.
Heading (Data) Water depth: No communication or data error.
Depth (Data) Water temperature: No communication or data error.
TEMP. (Data) Wind direction/velocity: No communication or data error.
Wind (Data) Tidal current: No communication or data error.
Current (Data) Rate of Turn: No communication or data error.
ROT (Data) Rudder Sensor Angle: No communication or data error.
RSA (Data) APB: No communication or data error.
Autopilot (Data) LCD monitor: Fan error.
Fan (LCD) RADAR Process Unit Interconnection: Fan error.
Fan (Power) Power Supply: Fan error.
Fan (PROC) Scanner: Safety switch OFF.

Table9-2： List of Notification

Message Description
CCRP Changed CCRP is automatic changed.
Weather INFO Weather information is received.
Copying Display is capturing to file.

9－ 2
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING

Table9-2： List of Notification

Set GYRO Requires setting of true bearing.
TM Reset Use care of resetting TM.
POSN Reset Change the latitude and longitude sentence.

Table9-3： List of Target Tracking Alarms and AIS Function Alarms

メッセージ 内 容
CPA/TCPA There is a dangerous target.
Trial There is a dangerous target, when trial maneuver is active.
New Target Acquisition or activation of a target in the automatic acquisition
/ activation zone.
Lost Failure in tracking the target that has been under tracking.
Failure in receiving AIS target data for a specified time.
REF Target Decrease in the reference target accuracy.
MAX Target The maximum number of targets is under acquisition.
95% Capacity Over 95% of the maximum number of targets to be tracked.
AIS Max Target Maximum number of AIS targets.
AIS 95% Capacity Over 95% of the maximum number of AIS targets.
AIS ACT MAX Maximum number of AIS targets to be activated.
AIS ACT 95% Over 95% of the maximum number of AIS targets to be
Capacity activated.
TT (Boot) Target tracking unit start failure.
TT (Data) The target tracking unit is malfunctioning.
AIS (Data) AIS: No communication or communication error.
AIS PROC (Data) AIS processing circuit: No communication or communication error.
i
AIS Alarm *** AIS alarm (Up to 10 alarm messages can be displayed.).
i. *** is a 3-digit number which is Local Alarm No in the ALR sentence.

Table9-4： List of Route Messages and Warnings

Message Description
Arrival
Break Off(WPT)
Arrive at way point.
Out of the way point.
9
Approach Approach the route.
Cross Track Error Go off the route.

Table9-5： List of Operational Error Messages and Warnings

Message Description
No Position Data Mark or line input when the latitude and longitude is invalid.
No Heading Data Target tracking operation or TM selection when bearing data is
invalid.
Out of Range Out of target acquisition range.

9－ 3
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING

Table9-5： List of Operational Error Messages and Warnings

Invalid Range TM selection due to TM-disabled range (96 nm).
Zooming in a ZOOM-disabled range (0.125 nm).
MAX Point Tried to enter navigation information beyond the specified.
Can't Transmit Tried to transmit within 5 second after standby or when the
transmitter-receiver has any trouble.
Invalid Data Tried to enter any data beyond its range.
Invalid Connection The operator set performance monitor to on without selecting
straight.
No Card Card not detected yet.
Card Full Card capacity insufficient.
Format Card Unformatted card.
Invalid Card Invalid card.
Read Failed Read failure.
Write Failed Write failure.
Delete Failed Deletion failure.
Format Failed Format failure.
Copy Failed Copy failure.
Not Allowed General operation error.
No Object No object at the cursor-specified position.
Slave Mode Operation of a menu for the scanner unit when the slave mode
is active.

Table9-6： List of Conditions Messages

Message Description
GPS (HDOP) The HDOP level is increased (Decrease in the GPS accuracy.).
MON Test Performance monitor is active.
Scanner Rotating The scanner is rotating (When transmitter is standby state.).
Battery Low battery is weakening.
Battery Dead The battery is dead.

Table9-7： List of Interswitch Alarms and Messages

Message Description
Master Range CHG The range of the own display unit has changed due to
change in the range of the master display unit.
ISW Complete The switchover of the Interswitch ended normally.
ISW Busy Access to the ISW menu was made during interswitching.
TXRX Standby The scanner unit is in the standby mode.
ISW Straight Failed in straight connection when the Interswitch
system stops operating.
ISW Standby The Interswitch recovered normally.
ISW Time Out Failed in switching.
ISW Error The interswitch is disabled.

9－ 4
 JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING

Table9-7： List of Interswitch Alarms and Messages

Pattern CHG Failed Connection change failed.
Connection Masked Inhibition of control / connection is set.
Master Standby The master display unit does not transmit any signals.
ISW (Data) No communication, data mismatched, or checksum error.
Update ISW Software Tried to enter new TXRX function, when interswitch
software used old version.

9.1.2 Operation Checking

When the system is operating, the operation status (located at the upper right of
the screen) is changing pictures.

If picture freeze occurred, turn off the system and restart the system.

Operation Status

9.1.3 Fuse Checking

Melted fuses are caused by any clear cause. When a fuse is replaced, it is
necessary to check the related circuits even if there is no trouble. In checking, note
that there is some dispersion in the fusing characteristics. Table 9-8 shows a list of
fuses used in the equipment. 9
Table9-8： Fuse List
Location Parts# C u r r e n t P r o t e c t i o n Type
Rating Circuit

AC/DC Converter F501 10A Motor ST6-10AN1

GYRO Interface F1 ～ F4 0.5A GYRO MF60NR250V0.5

circuit Interface
circuit

9－ 5
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING

9.2 TROUBLE SHOOTING

As this radar equipment includes complicated circuits, it is necessary to request a

specialist engineer for repair or instructions for remedy if any circuit is defective.

There are also troubles by the following causes, which should be referred to in
checking or repair work.

１ Poor Contact in Terminal Board of Inter-Unit Cables

a. Poor contact in terminal board
b. The cable end is not fully connected, that it, contacted with earthed another
terminal.
c. Disconnected cable wire

２ Poor Contact of Connector within Unit

This radar equipment is provided with Table 9-9 standard
i spares.

Table9-9： 7ZXRD0025

Name Type/Code Shape (mm) In Spare Parts # Location

use
Fuse MF60NR250V0.5 4 12 F1 ～ F4 GYRO I/F

(5ZFGD00006) CMJ-462E
Φ6.4
30

Fuse ST6-10AN1 1 3 F501 AC/DC Converter

(5ZFCA00053) NBA-5135
Φ6.35
31.8

9－ 6
 JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING

9.2.1 Special Parts

NKE-2103

Table9-10： NKE-2103 (JMA-9110-6XA/6XAH、JMA-7110-6XA/6XAH)

Parts No. Name Type Manufacture Location Code

V101 Magnetron MAF1565N NJRC Scanner Unit 5VMAA00102
A101/A102 Circulator FCX68 Toshiba Scanner Unit 6AJRD00001
A301 Diode Limiter NJS6930 NJRC Scanner Unit 5ATBT00006

NKE-1125/2254

Table9-11： NKE-1125/2254 (JMA-9122-6XAH/9XA/6XAH、JMA-7122-6XA/9XA/6XAH)

Parts No. Name Type Manufacture Location Code

V101 Magnetron M1568BS NJRC Scanner Unit 5VMAA00106
A101/A102 Circulator NJC3901M NJRC Scanner Unit 5AJBV00007
A301 Diode Limiter NJS6930 NJRC Scanner Unit 5ATBT00006

NTG-3225

Table9-12： NTG-3225 (JMA-9123-7XA/9XA、JMA-7123-7XA/9XA)

Parts No. Name Type Manufacture Location Code
V101 Magnetron M1568BS NJRC Transmitter 5VMAA00106
Receiver Unit

A101/A102 Circulator NJC3901M NJRC Transmitter 5AJBV00007

Receiver Unit

A301 Diode Limiter NJS6930 NJRC Transmitter 5ATBT00006

Receiver Unit

NKE-1130

Table9-13： NKE-1130 (JMA-9132-SA、JMA-7132-SA)

Parts No. Name Type Manufacture Location Code

V101
A101/A102
Magnetron
Circulator
M1555
NJC3316
NJRC
NJRC
Scanner Unit

Scanner Unit
5VMAA00106
5AJBV00007
9
A301 Diode Limiter NJS6318 NJRC Scanner Unit 5ATBT00006

NTG-3230

Table9-14： NTG-3230 (JMA-9133-SA、JMA-7133-SA)

Parts No. Name Type Manufacture Location Code
V101 Magnetron M1555 NJRC Transmitter 5VMAA00104
Receiver Unit

A101 Circulator NJC3317 NJRC Transmitter 5AJBV00009

Receiver Unit

A301 TR Limiter TL378A NJRC Transmitter 5VLAA00037

Receiver Unit

9－ 7
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING

9.2.2 Circuit Block to be Repaired

Table9-15： Circuit Block to be Repaired (JMA-9110-6XA/6XAH)

Location Circuit Block Type Remarks

SCANNER UNIT GEARED MOTOR 7BDRD0048 DC brushless motor (common
with HS)
SCANNER UNIT MODULATOR CIRCUIT CME-363 Excluding Magnetron
SCANNER UNIT RECEIVER UNIT NRG-610 Including CAE-529-1
SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1783
SCANNER UNIT ENCODER CHT-71A
SCANNER UNIT MOTOR CONTROL POWER CBD-1779
SUPPLY
SCANNER UNIT FAN 7BFRD0002
RADAR RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
PROCESS UNIT

RADAR AIS PROCESS CIRCUIT CDC-1325

PROCESS UNIT

RADAR ARPA PROCESS CIRCUIT CDC-1186D

PROCESS UNIT

RADAR GYRO I/F CIRCUIT CMJ-462E

PROCESS UNIT

RADAR TERMINALBOARD CIRCUIT CQD-2097

PROCESS UNIT

RADAR MOTHERBOARD CIRCUIT CQC-1192

PROCESS UNIT

RADAR FAN (RPU) 109R0612S4D13

PROCESS UNIT

RADAR POWER SUPPLY CBD-1661

PROCESS UNIT

RADAR FAN (PSU) 7BFRD0006

PROCESS UNIT

OPERATION OPERATION CIRCUIT A CCK-973

UNIT

OPERATION OPERATION CIRCUIT B CCK-974

UNIT

OPERATION OPERATION CIRCUIT D CCK-976

UNIT

OPERATION TRACKBALL 5EZLY00003

UNIT

OPERATION LCD PANEL 7WSRD0002A 23.1-inch LCD

UNIT

OPERATION LCD OPERATION CIRCUIT CCK-972

UNIT

9－ 8
 JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING

Table9-16： Circuit Block to be Repaired (JMA-9122-6XA/9XA)

Location Circuit Block Type Remarks

SCANNER UNIT GEARED MOTOR MDBW10822 For 100/220VAC
SCANNER UNIT ENCODER CHT-71A
SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VAC
SCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VAC
SCANNER UNIT PERFORMANCE MONITOR NJU-85
SCANNER UNIT HEATER CONTROL PART CHG-216 Option (AC100V)
SCANNER UNIT BREAK CIRCUIT CFA-253
SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655
SCANNER UNIT BREAK CIRCUIT A CFA-259
SCANNER UNIT BREAK CIRCUIT B CFA-260
SCANNER UNIT T/R CONTROL CIRCUIT CMC-1205R
SCANNER UNIT MODULATOR UNIT NMA-550 Including CPA-264
Including CMB-404
Including CFR-229
Excluding Magnetron
SCANNER UNIT MODULATOR CIRCUIT CPA-264
SCANNER UNIT RECEIVER UNIT NRG-162A Including CMA-866A
SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1682A
SCANNER UNIT RELAY FILTER CIRCUIT CSC-656
SCANNER UNIT FAN 7BFRD0002
RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT

OPERATION UNIT

OPERATION UNIT
FAN (PSU)
OPERATION CIRCUIT A
OPERATION CIRCUIT B
7BFRD0006
CCK-973
CCK-974
9
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972

9－ 9
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING

Table9-17： Circuit Block to be Repaired (JMA-9122-6XAH)

Location Circuit Block Type Remarks

SCANNER UNIT GEARED MOTOR 7BDRD0045A For 100/220VAC
SCANNER UNIT ENCODER CHT-71A
SCANNER UNIT MOTOR CONTROL POWER CBD-1779
CIRCUIT
SCANNER UNIT BREAK CIRCUIT CFA-257
SCANNER UNIT PERFORMANCE MONITOR NJU-85
SCANNER UNIT HEATER CONTROL PART CHG-216 Option (AC100V)
SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1682A
SCANNER UNIT T/R CONTROL CIRCUIT CMC-1205R
SCANNER UNIT MODULATOR UNIT NMA-550 Including CPA-264
Including CMB-404
Including CFR-229
Excluding Magnetron
SCANNER UNIT MODULATOR CIRCUIT CPA-264
SCANNER UNIT RECEIVER UNIT NRG-162A Including CMA-866A
SCANNER UNIT FAN 7BFRD0002
RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT FAN (PSU) 7BFRD0006
OPERATION UNIT OPERATION CIRCUIT A CCK-973
OPERATION UNIT OPERATION CIRCUIT B CCK-974
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972

9－ 10
 JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING

Table9-18： Circuit Block to be Repaired (JMA-9123-7XA/9XA)

Location Circuit Block Type Remarks

SCANNER UNIT GEARED MOTOR MDBW10822 For 100/220VAC
SCANNER UNIT ENCODER CHT-71A
SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VAC
SCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VAC
SCANNER UNIT PERFORMANCE MONITOR NJU-85
SCANNER UNIT HEATER CONTROL PART CHG-216 Option (AC100V)
SCANNER UNIT BREAK CIRCUIT CFA-253
SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655
SCANNER UNIT BREAK CIRCUIT A CFA-259
SCANNER UNIT BREAK CIRCUIT B CFA-260
TRANSMITTER T/R CONTROL CIRCUIT CMC-1205R
RECEIVER UNIT

TRANSMITTER MODULATOR UNIT NMA-552 Including CPA-264

RECEIVER UNIT
Including CMB-405
Including CFR-229
Excluding Magnetron
TRANSMITTER MODULATOR CIRCUIT CPA-264
RECEIVER UNIT

TRANSMITTER RECEIVER UNIT NRG-162A Including CMA-866A

RECEIVER UNIT

TRANSMITTER POWER SUPPLY CIRCUIT CBD-1682A

RECEIVER UNIT

TRANSMITTER RELAY FILTER CIRCUIT CSC-656

RECEIVER UNIT

RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT

OPERATION UNIT
FAN (PSU)
OPERATION CIRCUIT A
7BFRD0006
CCK-973
9
OPERATION UNIT OPERATION CIRCUIT B CCK-974
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972

9－ 11
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING

Table9-19： Circuit Block to be Repaired (JMA-9132-SA)

Location Circuit Block Type Remarks

SCANNER UNIT GEARED MOTOR MDBW10823 For 100/220VAC
SCANNER UNIT ENCODER CHT-71A1
SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VAC
SCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VAC
SCANNER UNIT PERFORMANCE MONITOR NJU-84
SCANNER UNIT HEATER CONTROL PART CHG-215 Option (AC100V)
SCANNER UNIT BREAK CIRCUIT CFA-255
SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655
SCANNER UNIT BREAK CIRCUIT A CFA-261
SCANNER UNIT BREAK CIRCUIT B CFA-262
SCANNER UNIT T/R CONTROL CIRCUIT CMC-1205R
SCANNER UNIT MODULATOR UNIT NMA-551 Including CPA-264
Including CMB-406
Including CFR-229
Exluding Magnetron
SCANNER UNIT MODULATOR CIRCUIT CPA-264
SCANNER UNIT RECEIVER UNIT NRG-229
SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1682A
SCANNER UNIT RELAY FILTER CIRCUIT CSC-656
SCANNER UNIT FAN 7BFRD0002
RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT FAN (PSU) 7BFRD0006
OPERATION UNIT OPERATION CIRCUIT A CCK-973
OPERATION UNIT OPERATION CIRCUIT B CCK-974
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972

9－ 12
 JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING

Table9-20： Circuit Block to be Repaired (JMA-9133-SA)

Location Circuit Block Type Remarks

SCANNER UNIT GEARED MOTOR MDBW10823 For 100/220VAC
SCANNER UNIT ENCODER CHT-71A1
SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VAC
SCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VAC
SCANNER UNIT PERFORMANCE MONITOR NJU-84
SCANNER UNIT HEATER CONTROL PART CHG-215 Option (AC100V)
SCANNER UNIT BREAK CIRCUIT CFA-255
SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655
SCANNER UNIT BREAK CIRCUIT A CFA-261
SCANNER UNIT BREAK CIRCUIT B CFA-262
TRANSMITTER T/R CONTROL CIRCUIT CMC-1205R
RECEIVER UNIT

TRANSMITTER MODULATOR UNIT NMA-553 Including CPA-264

RECEIVER UNIT
Including CMB-407
Including CFR-229
Exluding Magnetron
TRANSMITTER MODULATOR CIRCUIT CPA-264
RECEIVER UNIT

TRANSMITTER RECEIVER UNIT NRG-229

RECEIVER UNIT

TRANSMITTER POWER SUPPLY CIRCUIT CBD-1682A

RECEIVER UNIT

TRANSMITTER RELAY FILTER CIRCUIT CSC-656

RECEIVER UNIT

RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT

OPERATION UNIT
FAN (PSU)
OPERATION CIRCUIT A
7BFRD0006
CCK-973
9
OPERATION UNIT OPERATION CIRCUIT B CCK-974
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972

9－ 13
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE

9.3 AFTER-SALES SERVICE

9.3.1 Keeping period of maintenance parts

Keeping period of maintenance parts is ten years from the production is
discontinued.

9.3.2 When you Request for Repair

If you suppose the product may be out of order, read the description in Section 9
carefully and check the suspected point again.

If it is still out of order, you are recommended to stop operation of the equipment
and consult with the dealer from whom you purchased the product, or our branch
office in your country or district, the sales department in our main office in Tokyo.

Repair within the Warranty Period

If any failure occurs in the product during its normal operation in accordance with
the instruction manual, the dealer or JRC will repair free of charge. In case that
any failure is caused due to misuse, faulty operation, negligence or force major
such as natural disaster and fire, the product will be repaired with charges.

Repair after the Warranty Period

If any defective function of the product is recoverable by repair, the repair of it

will be made at your own charge upon your request.

Necessary Information for Repair

• Product name, model, manufacturing date and serial number

• Trouble conditions (as detailed as possible. Refer to "Radar Failure Check
List" on page 9-15
• Name of company/organization, address and telephone number

9.3.3 Recommended Maintenance

The performance of the product may deteriorate due to the secular change of the
parts used in it, though such deterioration depends upon the conditions of
operation. So checkup and maintenance is recommendable for the product in
addition to your daily care.

For maintenance, consult with the near-by dealer or our sales department.Such
maintenance will be made with charges.

For further details of after-sale service, contact the JRC Offices.

9－ 14
 JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE

Radar Failure Check List

When placing an order for repair of the product, it is requested that you could
i confirm the check items and fill the results and sent the sheet to our contact.
If there is any unclear items, contact the ship on which the product is
installed, and give the correct information on the product.

Ship name: Phone: Fax:

i i
Radar general model name :JMA- Serial No. :
i. Write the full model name correctly

Check the following items in the order of the number, and check the applicable
answer between YES or NO.

If the item cannot be determined as YES or NO, explain in detail in the item (18),
others.

No. Check Item Result

(1) Power can be turned on. (The lamp on the Operation unit is lit) YES NO
i
(2) A few minutes after powering-on, it will become standby status. YES NO
(3)i When powering-on (or TX ON), LCD monitor something is lit. YES NO
i,ii
(4) The antenna rotates at the transmission (TX) ON. YES NO
i,ii
(5) Current is supplied to the magnetron. (Refer to the instruction manual) YES NO
(6)ii Turning is enabled. (Check with the range of 6 NM or more) YES NO
ii
(7) Fixed marker is displayed. YES NO
ii
(8) VRM is displayed. YES NO
(9)ii While noise is displayed while set at SEA and RAIN minimum, GAIN YES NO
maximum, IR-OFF and range 48 NM.
(10)ii Target reflection echo is displayed. YES NO
ii
(11) Sensitivity of reflection echo is normal. YES NO
(12)ii EBL is displayed. YES NO
ii
(13) Cursor mark moves. YES NO
ii,iii
(14) GYRO course can be set and normally displayed. YES NO
(15)ii,iii LOG speed can be normally displayed. YES NO
(16)
(17)
ii

ii,iii
Target tracking function works normally.
If equipped with an interswitch, when switching from the straight mode (II) to YES
(X), the failures (items marked NO) in the above (1) to (16), are switched over
YES NO
NO 9
to the other unit.
（18） Others (Error message, etc. )

i. If result is NO, then check the fuse. (Refer to Section 9.1.2 "Operation Checking" and Section 9.2 "TROUBLE
SHOOTING")
ii. Check these items while transmission is ON.
iii. Functions mentioned in the items (14), (15) and (17) may be optional, answer is not necessary.

9－ 15
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE

9－ 16
 SECTION 10
DISPOSAL

DISPOSAL
10.1 DISPOSAL OF THE UNIT ....................................................................10-1
10.2 DISPOSAL OF USED BATTERIES .....................................................10-1
10.3 DISPOSAL OF USED MAGNETRON ..................................................10-2
10.4 DISPOSAL OF TR-TUBE .....................................................................10-2
10.5 ABOUT THE CHINA ROHS .................................................................10-3
 JMA-9100 Instruction Manual > 10.DISPOSAL > 10.1 DISPOSAL OF THE UNIT

10.1 DISPOSAL OF THE UNIT

When disposing of this unit, be sure to follow the local laws and regulations for
the place of disposal.

10.2 DISPOSAL OF USED BATTERIES

When disposing of used lithium batteries, be sure to

insulate the batteries by taping the + - terminals.
Otherwise, heat generation, explosion or a fire may
occur.

In this unit, Lithium batteries are used for the following parts:

Radar Processing circuit (CDC-1324): BT1 (Maxell: CR2032)

• Do not store used lithium batteries. Dispose of them in accordance with

regulations of local government.
• When disposing of used lithium batteries be sure to insulate the batteries by
taping the + - terminals. For disposal of batteries, be sure to follow the local
laws and regulations. For detail, consult with the dealer you purchased the
product our business office, or local government.
10

10－ 1
 JMA-9100 Instruction Manual > 10.DISPOSAL > 10.3 DISPOSAL OF USED MAGNETRON

10.3 DISPOSAL OF USED MAGNETRON

Magnetron is used in the Scanner （NKE－ 2103/2254/1125/1130）and

Transmitter Receiver Unit (NTG-3225/3230).

• When the magnetron is replaced with a new one, return the used magnetron to
our dealer or business office.
For detail, consult with our dealer or business office.

10.4 DISPOSAL OF TR-TUBE

In the case that either mark shown in Fig 10-1 is on the expired TR-tube,
Radioisotopes are in the TR-tube.

• Disposal of TR-tube with these marks must be done in accordance with the
laws and regulations of the pertaining country. For detail, consult with our
dealer or business office.
• Radiation from TR-tube has no effect on the human body.
• Don't take apart TR-tube.

Fig 10-1: Radioisotopes Marks 10

10－ 2
 JMA-9100 Instruction Manual > 10.DISPOSAL > 10.5 ABOUT THE CHINA ROHS

10.5 ABOUT THE CHINA ROHS

有毒有害物质或元素的名称及含量
(Names & Content of toxic and hazardous substances or elements）

形式名(Type): JMA-9100 Series, JMA-7100Series 名称(Name): RADAR

有毒有害物质或元素
部件名称 (Toxic and Hazardous Substances and Elements)
(Part name)
铅 汞 镉 六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr6+) (PBB) (PBDE)

雷达天线单元
(Scanner Unit) × × ○ × × ×
收发信单元
(Transmitter-receiver Unit) × × × × × ×
主船内装置 (Inboard Unit)
・显示装置 (Display Unit)
・键盘装置 (OperationUnit) × × × × × ×
・信号处理装置
(RADAR Process Unit)

外部设备 (Peripherals)
・选择 (Options)
・电线类 (Cables) × × × × × ×
・手册 (Documennts)

○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11306-2006 标准规定的限量要求以下。
(Indicates that this toxic, or hazardous substance contained in all of the homogeneous materials for this
part is below the requirement in SJ/T11363-2006.)

×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限量要求。
(Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials
used for this part is above the limit requirement in SJ/T 11363-2006.)

10

10－ 3
JMA-9100 Instruction Manual > 10.DISPOSAL > 10.5 ABOUT THE CHINA ROHS

10－ 4
 SECTION 11
SPECIFICATION

SPECIFICATION
11.1 JMA-9133-SA TYPE RADAR ...............................................................11-1
11.2 JMA-9132-SA TYPE RADAR ............................................................... 11-2
11.3 JMA-9123-7XA/9XA TYPE RADAR ....................................................11-3
11.4 JMA-9122-6XA/9XA TYPE RADAR ....................................................11-4
11.5 JMA-9122-6XAH TYPE RADAR .........................................................11-5
11.6 JMA-9110-6XA TYPE RADAR ............................................................11-6
11.7 JMA-9110-6XAH TYPE RADAR .........................................................11-7
11.8 SCANNER UNIT (NKE-1139) ...............................................................11-8
11.9 SCANNER UNIT (NKE-1130) ...............................................................11-9
11.10 SCANNER UNIT (NKE-1129-7/9) ......................................................11-10
11.11 SCANNER UNIT (NKE-1125-6/9) .......................................................11-11
11.12 SCANNER UNIT (NKE-2254-6HS) .....................................................11-12
11.13 SCANNER UNIT (NKE-2103-6) ..........................................................11-13
11.14 SCANNER UNIT (NKE-2103-6HS) .....................................................11-14
11.15 TRANSMITTER RECEIVER UNIT (NTG-3230) .................................11-15
11.16 TRANSMITTER RECEIVER UNIT (NTG-3225) .................................11-16
11.17 DISPLAY UNIT (NCD-4990) ...............................................................11-17
11.18 Target Tracking Function .................................................................11-20
11.19 AIS FUNCTION ...................................................................................11-21
11.20 PERFORMANCE MONITOR (NJU-84) ..............................................11-22
11.21 PERFORMANCE MONITOR (NJU-85) ..............................................11-22
11.22 AC-DC CONVERTER (NBA-5135) .....................................................11-22
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.1 JMA-9133-SA TYPE RADAR

11.1 JMA-9133-SA TYPE RADAR

GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125、0.25、0.5、0.75、1.5、3、6、12、24、48、96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit -15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.400VA typical
Approx. 2000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1139)

See 11.8
TRANSMITTER RECEIVER UNIT (NTG-3230)

See 11.15
DISPLAY UNIT (NCD-4990)

See 11.17
PERFORMANCE MONITOR (NJU-84)

See 11.20
OPTION

Scanner with Deicing Heater NKE-1139-D (Only heater collar)

Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length

SCANNER UNIT to 30m

TRANSMITTER RECEIVER UNIT
DISPLAY UNIT to 35m
TRANSMITTER RECEIVER UNIT
SAFE DISTANCE FOR STANDARD COMPASS

SCANNER UNIT 1.4m

11
TRANSMITTER RECEIVER UNIT 3.9m
DISPLAY UNIT 4.0m

11－ 1
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.2 JMA-9132-SA TYPE RADAR

11.2 JMA-9132-SA TYPE RADAR

GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit -15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.400VA typical
Approx. 2000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1130)

See 11.9
DISPLAY UNIT (NCD-4990)

See 11.17
PERFORMANCE MONITOR (NJU-84)

See 11.20
OPTION

Scanner with Deicing Heater NKE-1139-D (Only heater collar)

Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length

SCANNER UNIT to 65m

TRANSMITTER RECEIVER UNIT
SAFE DISTANCE FOR STANDARD COMPASS

SCANNER UNIT 5.1m

DISPLAY UNIT 4.0m

11－ 2
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.3 JMA-9123-7XA/9XA TYPE RADAR

11.3 JMA-9123-7XA/9XA TYPE RADAR

GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit -15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1700VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1129-7/9)

See 11.10
TRANSMITTER RECEIVER UNIT (NTG-3225)

See 11.16
DISPLAY UNIT (NCD-4990)

See 11.17
PERFORMANCE MONITOR (NJU-85)

See 11.21
OPTION

Scanner with Deicing Heater NKE-1139-D (Only heater collar)

Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length

SCANNER UNIT to 30m

TRANSMITTER RECEIVER UNIT
DISPLAY UNIT to 35m
TRANSMITTER RECEIVER UNIT
SAFE DISTANCE FOR STANDARD COMPASS

SCANNER UNIT 1.05m

11
TRANSMITTER RECEIVER UNIT 2.8m
DISPLAY UNIT 4.0m

11－ 3
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.4 JMA-9122-6XA/9XA TYPE RADAR

11.4 JMA-9122-6XA/9XA TYPE RADAR

GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit -15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1700VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1125-6/9)

See 11.11
DISPLAY UNIT (NCD-4990)

See 11.17
PERFORMANCE MONITOR (NJU-85)

See 11.21
OPTION

Scanner with Deicing Heater NKE-1139-D (Only heater collar)

Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to 65m
TRANSMITTER RECEIVER UNIT
SAFE DISTANCE FOR STANDARD COMPASS

SCANNER UNIT 2.4m

DISPLAY UNIT 4.0m

11－ 4
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.5 JMA-9122-6XAH TYPE RADAR

11.5 JMA-9122-6XAH TYPE RADAR

GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit -15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-2254-6HS)

See 11.11
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)

See 11.21
AC-DC CONVERTER (NBA-5135)
See 11.22
OPTION
Scanner with Deicing Heater None
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to 65m
TRANSMITTER RECEIVER UNIT
SAFE DISTANCE FOR STANDARD COMPASS

SCANNER UNIT 2.4m

DISPLAY UNIT 4.0m
11

11－ 5
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.6 JMA-9110-6XA TYPE RADAR

11.6 JMA-9110-6XA TYPE RADAR

GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit -15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-2103-6)
See 11.13
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR
(NJU-85)
See 11.21
AC-DC CONVERTER (NBA-
5135)
See 11.22
OPTION
Scanner with Deicing Heater None
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to 65m
TRANSMITTER RECEIVER UNIT

SAFE DISTANCE FOR

STANDARD COMPASS
SCANNER UNIT 2.4m
DISPLAY UNIT 4.0m

11－ 6
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.7 JMA-9110-6XAH TYPE RADAR

11.7 JMA-9110-6XAH TYPE RADAR

GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit -15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-2103-6HS)
See 11.14
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)

See 11.21
AC-DC CONVERTER (NBA-5135)
See 11.22
OPTION
Scanner with Deicing Heater None
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT～ DISPLAY 65m
UNIT
SAFE DISTANCE FOR STANDARD COMPASS

SCANNER UNIT 2.4m

DISPLAY UNIT 4.0m
11

11－ 7
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.8 SCANNER UNIT (NKE-1139)

11.8 SCANNER UNIT (NKE-1139)

SCANNER UNIT NKE-1139

Dimension Height 791 x Swing Circle 4000 (mm)
Mass Approx.150kg
Polarization Horizontal
Directional Characteristics Horizontal beam width : 1.9°
Vertical beam width : 25°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)

11－ 8
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.9 SCANNER UNIT (NKE-1130)

11.9 SCANNER UNIT (NKE-1130)

SCANNER UNIT NKE-1130

Dimension Height 791 x Swing Circle 4000 (mm)
Mass Approx.180kg
Polarization Horizontal
Directional Characteristics Horizontal beam width : 1.9°
Vertical beam width : 25°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 3050 ± 20MHz
Transmitting Power 30kW
Transmitting Tube Magnetron[M1555]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency : 60MHz
Band Width : 25/8/3MHz
Gain : more than 90dB
Amplifying Characteristics : Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO

11

11－ 9
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.10 SCANNER UNIT (NKE-1129-7/9)

11.10 SCANNER UNIT (NKE-1129-7/9)

SCANNER UNIT NKE-1129-7/9

Dimension 7ft Height 536 x Swing Circle 2270 (mm)
9ft Height 536 x Swing Circle 2825 (mm)
Mass 7ft Approx.51kg
9ft Approx.53kg
Polarization Horizontal
Directional Characteristics Horizontal beam width : 1.0° (7ft)
: 0.8° (9ft)
Vertical beam width : 20°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)

11 －10
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.11 SCANNER UNIT (NKE-1125-6/9)

11.11 SCANNER UNIT (NKE-1125-6/9)

SCANNER UNIT NKE-1125-6/9

Dimension 6ft Height 536 x Swing Circle 1910 (mm)
9ft Height 536 x Swing Circle 2825 (mm)
Mass 6ft Approx. 55kg
9ft Approx. 60kg
Polarization Horizontal
Directional Characteristics Horizontal beam width : 1.2° (6ft)
: 0.8° (9ft)
Vertical beam width : 20°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 25kW
Transmitting Tube Magnetron[M1568BS]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency : 60MHz
Band Width : 25/8/3MHz
Gain : more than 90dB
Amplifying Characteristics : Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO

11

11－ 11
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.12 SCANNER UNIT (NKE-2254-6HS)

11.12 SCANNER UNIT (NKE-2254-6HS)

SCANNER UNIT NKE-2254-6HS

Dimension Height 536 x Swing Circle 1910 (mm)
Mass Approx. 55kg
Polarization Horizontal
Directional Characteristics Horizontal beam width : 1.2°
Vertical beam width : 20°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor DC24V
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 25kW
Transmitting Tube Magnetron[M1568BS]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency : 60MHz
Band Width : 25/8/3MHz
Gain : more than 90dB
Amplifying Characteristics : Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO

11 －12
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.13 SCANNER UNIT (NKE-2103-6)

11.13 SCANNER UNIT (NKE-2103-6)

SCANNER UNIT NKE-2103-6HS

Dimension Height 458 x Swing Circle 1910 (mm)
Mass Approx. 40kg
Polarization Horizontal
Directional Characteristics Horizontal beam width : 1.2°
Vertical beam width : 20°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor DC24V
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 10kW
Transmitting Tube Magnetron[MAF1565N]
TX Pulse width / Repetition SP1：0.08μs/2250Hz
Frequency MP1：0.25μs/1700Hz MP2：0.5μs/1200Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2
3NM ：MP1/MP2LP1
6NM ：MP1/MP2/LP1/LP2
12NM ：MP1/MP2/LP1/LP2
24NM ：MP2/LP1/LP2
48NM ：LP2
96NM ：LP2
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency : 60MHz
Band Width : 20/6/3MHz
Gain : more than 90dB
Amplifying Characteristics : Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO

11

11 －13
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.14 SCANNER UNIT (NKE-2103-6HS)

11.14 SCANNER UNIT (NKE-2103-6HS)

SCANNER UNIT NKE-2103-6HS

Dimension Height 458 x Swing Circle 1910 (mm)
Mass Approx. 40kg
Polarization Horizontal
Directional Characteristics Horizontal beam width : 1.2°
Vertical beam width : 20°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor DC24V
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 10kW
Transmitting Tube Magnetron[MAF1565N]
TX Pulse width / Repetition SP1：0.08μs/2250Hz
Frequency MP1：0.25μs/1700Hz MP2：0.5μs/1200Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2
3NM ：MP1/MP2LP1
6NM ：MP1/MP2/LP1/LP2
12NM ：MP1/MP2/LP1/LP2
24NM ：MP2/LP1/LP2
48NM ：LP2
96NM ：LP2
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency : 60MHz
Band Width : 20/6/3MHz
Gain : more than 90dB
Amplifying Characteristics : Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO

11 －14
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.15 TRANSMITTER RECEIVER UNIT (NTG-3230)

11.15 TRANSMITTER RECEIVER UNIT

(NTG-3230)

SCANNER UNIT NTG-3230

Dimension :Width 615 x Depth 365 x Height 615 (mm)
構造 Wall Mount, Drip Proof
Mass Approx.33kg
Transmitting Frequency 3050 ± 20MHz
Transmitting Power 30kW
Transmitting Tube Magnetron [M1555]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + TRHPL
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency : 60MHz
Band Width : 25/8/3MHz
Gain : more than 90dB
Amplifying Characteristics : Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO

11

11 －15
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.16 TRANSMITTER RECEIVER UNIT (NTG-3225)

11.16 TRANSMITTER RECEIVER UNIT

(NTG-3225)

SCANNER UNIT NTG-3225

Dimension :Width 460 x Depth 227 x Height 461 (mm)
構造 Wall Mount, Drip Proof
Mass Approx.15kg
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 25kW
Transmitting Tube Magnetron[M1568BS]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency : 60MHz
Band Width : 25/8/3MHz
Gain : more than 90dB
Amplifying Characteristics : Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO

11 －16
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990)

11.17 DISPLAY UNIT (NCD-4990)

DISPLAY UNIT NCD-4990
Dimension Width 700 x Depth 850 x Height 1100 (mm)
Structure Self-Standing, Drip Proof
Mass Approx.130kg
Screen 23.1inch Color LCD (Effective Diameter, more than 320mm)
Viewing Distance 1m from the center of Display
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Marker 0.025, 0.05, 0.1, 0.25, 0.5, 1, 2, 4, 8, 16NM
Range Accuracyr Less than 1% of the Range Scale in use, or 30m whichever is larger
Variable Range Marker 2 (VRM1/VRM2)
VRM Scale 0.000 to 100.0nm, Numerical Indication in 4 digits
Bearing Scale 360° in 1° step
Off Center Within 66% of Radius, except 96nm range
Trackball Cursor Built-in (Target Range, Relative/True bearing Presentation)
Electronic Bearing Lines 2 (EBL1/EBL2) (on Center/Floating)
EBLBearing Indication 000.0° to 359.9°Numerical Indication in 4 digits
Tuning Indication Bar graph
Marking Function Electronic Mark (Maximum 20 points)
Heading Line Indication Electronic
True Motion Unit Built in (0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24 and 48nm)
Anti Sea Clutter (SEA) Manual/AUTO
Anti Rain Clutter (SEA) Manual/AUTO
Display mode North-up / Head-up / Course-up
Trails Indication Off/0.25/0.5/1/3/6/10/15min and Continues
Video Process (PROC) Built in (Scan correlation / Remain)
Interference Rejection (IR) Built in ( Off / Low / Middle / High)
Auto-acquisition Zone (AZ) Sector (2)
User Mapi Built in, Mark and Line (20,000 points)
Self diagnostic function Built in
Own Ship's Track Indicationi Built in
Parallel Index Line (PI) Built in
AIS Indication Built in Display 300
Activate 100
Association function:Built in
Interfacing Slave Display (TRG, VD, BP, BZ)
GPS IEC61162-1(NMEA0183)
LOG
GYRO
AIS IEC61162-2
Inter Switch (OPTION)
Radar Buoy
External Alarm output
11
Receivable Signal

11 －17
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990)

Receive capability NAV1/ALM/ARPA/JARPA at terminal board TB4501

Port: COM port (D-Sub 9 PIN)
Navigation equipment Longitude/Latitude GGA>RMC>RMA>GNS>GLL
IEC61162-1/2
Waypoint RMB>BWC(BWR)
COG/SOG RMC ＞ RMA ＞ VTG
SPEED VBW
Day/Time information ZDA
Alarm acknowledge ACK
Rate of Turn ROT
Rudder RSA
Bearing signal GYRO-SYNC 360x, 180x, 90x, 36x(GYRO I/F)
GYRO-STEP 360x, 180x, 90x, 36x(GYRO I/F)
IEC61162-2 38400bps THS>HDT over 40Hz
(HDG port at terminal board TB4501)
IEC61162-1ii HDT>HDG>HDM>VHW
(HDG port at terminal board TB4501)
Speed signal LOG-SYNC 360x, 180x, 90x, 30x(GYRO I/F)
LOG-PULSE 800, 400, 200, 100(GYRO I/F)
External event mark Contact input (EVENT port at terminal board TB4601)
Radar buoy Negative input (RBVD port at terminal board TB4401)
Depth IEC61162-1/JRC DPT>DBS>DBT>DBK,
JRC format
Water temperature IEC61162-1/JRC MTW, JRC format
Tendency IEC61162-1/JRC CUR, JRC format
Wind IEC61162-1 MWV>MWD
AIS IEC61162-2 VDM,VDO (AIS port at terminal
board TB 4601 )
Acknowledge Contact input (SYSACK, ARPAACK, PWRACK port
at terminal board TB4601)
Sendable Signal
Slave video Radar video: TIY, VD, BP(2048p), BZ
(Terminal board TB4401)
Send capability NAV1, NAV2, ALM, ARPA, JARPA port
Port at terminal board TB4303. COM port (D-Sub 9 PIN)
Navigation information Radar system data RSD
IEC61162-1/2
Own ship data OSD
Tracking target data TTM,TLL,TTD,TLB,JRC-ARPA
AIS target data TTM,TLL,TTD,TLB
Alarm ALR
Auto pilot APB
Bearing of destination BOD
Latitude/Longitude data GGA,GLL,RMC
Waypoint RMB,BWC
COG/SOG VTG
Cross track error XTE
Heading data HDT,THS
External alarm Default setting normally closed contact

11 －18
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990)

Maximum current 200mA (SYSALM, ALPAALM, PWRALM

port at terminal board TB4601)

Acknowledge Contact output (ACKOUT port at terminal board TB4401)

Watchman reset Contact output (WMRST port at terminal board TB4401)
Remote maintenance JRC format (MNT port at terminal board TB4601)
AIS alarm acknowledge ACK (AIS port at terminal board TB4601)
External monitor Multi scan monitor Analog RGB, HD15pin Connector 2 port

i. Only with Navigation Equipment is connected.

The Speed measuring accuracy of speed sensor shall confirm to IMO Resolution MSC.96(72).
The measuring accuracy of GPS shall confirm to IMO Resolution MSC.112(73).

ii. Can't be use for target tracking.

11

11 －19
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.18 Target Tracking Function

11.18 Target Tracking Function

Target Tracking
Function
Available range scale All range
Acquisition Acquisition mode Manual/AUTO（AUTO mode uses Auto-acquisition Zone）
Manual Cancellation Any one Target or All targets at once
Tracking Number of Target 100 Targets (AUTO Tracking)
Maximum tracking range 32nm (Available all range scale)
Presentation Display mode TM (True Motion) / RM (Relative Motion)
Azimuth mode North-up / Head-up / Course-up
Vector mode True/Relative Display
Vector Length Variable, 1 to 60 min. (1min. step)
Past Position True/Relative Display
Number of Dots…10 points
Display Interval Time…0.5 / 1 / 2/ 4 min
Time to Display Vector Within 1min
Time to Stabilize Vector Within 3min
Alarm Auto-acquisition Zone 2 (sector)
Setting Range AZ1 (0.5 ～ 32NM),AZ2 (0.5 ～ 32NM)
Alarm Indication Symbol on Display, Visible / Audible Alarm
Safe Limits Setting Condition CPA LIMIT 0.1 to 9.9NM
（CPA ／ TCPA） TCPA LIMIT 1 to 99 minute
Setting Condition Safe Target CPA ＞ CPA LIMIT
0 ＞ TCPA
TCPA ＞ TCPA LIMIT
Danger Target CPA ≦ CPA LIMIT
0 ≦ TCPA ≦ TCPA LIMIT
Alarm Indication Status Symbol Alarm Audible
Safe Target 〇 (wht) OFF OFF
Danger Target ○ (red) CPA/TCPA ON
Lost Target Symbol on Display
Visible / Audible Alarm
Data Indication Target Data Simultaneous and Continuous Display for 4 Targets
True Bearing, Range, True Course, True Speed,CPA,TCPA,BCR,BCT

Own Ship's Data Course and Speed

Trial Maneuver Manual Setting
Trial Course 0°to 359.9°
Trial Speed 0 to 100 kn
Accuracy of Display Complied with IMO Requirement
System Failure Alarm Visible / Audible Alarm
Speed Input Manual/AUTO (LOG)

11 －20
 JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.19 AIS FUNCTION

11.19 AIS FUNCTION

AIS 機能
Available range scale All range
Activation Activation mode Manual/AUTO（AUTO mode uses Auto-activation Zone）
Manual Cancellation Any one Target
Presentation Number of Activated Target 100 Targets
Number of Target 300 Targets (sleeping target and activated target)
Past Position True/Relative Display
Number of Dots…10 points
Display Interval Time…0.5 / 1 / 2/ 4 min
Display Interval distance…0.1 / 0.2 / 0.5/ 1 NM
Message Broadcast Message, Addressed Message
Display mode TM (True Motion) / RM (Relative Motion)
Azimuth mode North-up / Head-up / Course-up
Vector mode True/Relative Display
Vector Length Variable, 1 to 60 min. (1min. step)
Alarm Auto-activation Zone 2 (Sector)
Setting Range AZ1(0.5 to 32nm), AZ2(0.5 to 32nm)
Alarm Indication Symbol on Display, Visible / Audible Alarm
Safe Limits Setting Condition CPA LIMIT 0.1 to 9.9NM
（CPA ／ TCPA） TCPA LIMIT 1 to 99min
Alarm Condition Safe Target CPA ＞ CPA LIMIT
0 ＞ TCPA
TCPA ＞ TCPA LIMIT
Danger Target CPA ≦ CPA LIMIT
0 ≦ TCPA ≦ TCPA LIMIT
Alarm Indication Status Symbol Alarm Audible
Safe Target △ (wht) OFF OFF
Danger Target △ (red) CPA/TCPA ON
Lost Target Symbol on Display
Visible / Audible Alarm
Data Indication Target Data Simultaneous and Continuous Display for 2 Targets
simple display Ship's Name, Call Sign, MMSI, Course, Speed,
CPA and TCPA
detail display Ship's Name, Call Sign, MMSI, Course, Speed, CPA,
TCPA, Bearing, Range, Ship's Heading Bearing,
Rate of Turn, Latitude, Longitude, Destination
and Navigation Status
Own Ship's Data The ship's name, call sign, MMSI, course, speed,

Trial Maneuver Manual Setting

ship's heading bearing, rate of turn, latitude,
longitude, destination and navigation status of own ship
11
Trial Course 0° to 360°
Trial Speed 0 to 100 kn

11 －21
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.20 PERFORMANCE MONITOR (NJU-84)

Accuracy of Display Complied with IMO Requirement

System Failure Alarm Visible / Audible Alarm
Speed Input Auto (LOG)

11.20 PERFORMANCE MONITOR (NJU-84)

PERFORMANCE MONITORNJU-84
Dimension Width 130 x Depth 180 x Height 70 (mm)
Mass Approx.0.7kg
Operating Frequency 3050 ± 30MHz

11.21 PERFORMANCE MONITOR (NJU-85)

PERFORMANCE MONITORNJU-85
Dimension Width 130 x Depth 149 x Height 70 (mm)
Mass Approx.0.7kg
Operating Frequency 9410 ± 30MHz

11.22 AC-DC CONVERTER (NBA-5135)

AC-DC CONVERTERNBA-5135
Dimension Width 315 x Depth 385 x Height 99 (mm)
Mass Approx.5kg
Power supply Input AC100 to 240V, 50/60Hz, 1φ
Output Voltage DC24V +/-5%
Output Current 12A max

11 －22
 Appendix A
NQE-3141 Interswitch Unit

NQE-3141 Interswitch Unit

A.1 OVERVIEW ............................................................................................ A-1
A.1.1 Overview ......................................................................................... A-1
A.1.2 Interswitch Setup ........................................................................... A-1
A.2 INTERSWITCH OPERATION ................................................................ A-3
A.2.1 Operation Flow ............................................................................... A-3
A.2.2 Inter Switch Menu ........................................................................... A-4
A.2.3 Change of Connection Pattern (with 2 Display Units) ................ A-6
A.2.4 Change of Connection Pattern (with 3 or More Display Units) .. A-7
A.2.5 Operating Connection Pattern Files (File Operations) ............... A-8
A.2.6 Names of Display Units and Scanner Units ................................. A-9
A.3 REFERENCE ....................................................................................... A-10
A.3.1 Preheat Time after Change of Connection Pattern ................... A-10
A.3.2 Notes on Changing Connection Pattern .................................... A-10
A.3.3 Notes on Connecting Slave Display Unit ................................... A-10
A.3.4 Setting at Installation ................................................................... A-11
 JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.1 OVERVIEW

A.1 OVERVIEW

A.1.1 Overview
Interswitch NQE-3141 is equipment that enables free changeover between radar
display units installed on the bridge and antenna units having different
characteristics.

If display unit is turned off or malfunctioned, the scanner unit can be controlled by
other display unit.

If interswitch unit had malfunctioned, the radar system is switched to standalone

mode.

Up to 8 units can be changed over.

When the connected scanner is changed, following setting values are

automatically loaded.

Tune Adjustment Section 7.1.3 "Tuning (Tune Adjustment)"

Bearing Adjustment Section 7.1.4 "Bearing Adjustment"

Range Adjustment Section 7.1.5 "Range Adjustment"

Antenna Height Section 7.1.8 "Antenna Height Setting (Antenna

Height)"

Antenna installation location Section 7.1.9 "Setting of CCRP (CCRP Setting)"

Sector Blank Section 7.2.2 "Sector Blank Setting (Sector Blank)"

TNI Blank Section 7.2.3 "TNI Blank Setting (TNI Blank)"

Performance monitor Section 7.3.4 "Adjustment of Performance Monitor"

adjustment

PRF Fine Tuning Section 3.8.3 "Set Scanner Unit (TXRX Setting)"

A.1.2 Interswitch Setup

Connection modes can be changed simply by changing the interswitch connection
(upper left of the display).
A master display unit is always necessary for establishing a slave
i connection.

Before a slave display unit can be placed in transmission state, the

master display unit must be placed in transmission state.

A
A－ 1
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.1 OVERVIEW

upper left of the display

Connected
Scanner
Unit
Connection
Mode
Connection Switch

The upper stand indicates the number of the connected scanner unit.

The lower stand indicates the connection mode.

Master :Mode in which the scanner unit can be controlled by the

display unit
Slave :Mode in which the scanner unit cannot be controlledi

i. When Slave is selected, transmission / standby and pulse length cannot be changed.
The available range is also limited.

A－ 2
 JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION

A.2 INTERSWITCH OPERATION

Follow the flowchart below to change the current interswitch connection pattern.

A.2.1 Operation Flow

Place the transmission standby state .

Open the Inter Switch Menu .

Change the connection pattern .

Close the Inter Switch Menu .

A
A－ 3
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION

A.2.2 Inter Switch Menu

The Inter Switch Menu can be opened only when the transmission standby state.

Procedures
1) Press the [TX/STBY] key to stop transmitting.
The transmission standby state will be placed.

2) Move the cursor onto the Interswitch connection change (upper

left of the display), and left-click.
The Inter Switch Menu will appear.

Exit
1) Left-click the 0.Exit button.
The Inter Switch Menu will close.

Inter Switch Menu (with 2 Display Units)

Current
connection
status

a. Connection
pattern

Display unit
in operation

b. Set c.Exit

A－ 4
 JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION

a. Connection pattern
If this button is clicked, the connection pattern is selected.

The display unit in operation is enclosed in a square □ .

The background of the current connection pattern display is highlighted.

b. Set
If this button is clicked, the change of connection is determined.

c. Exit
If this button is clicked, the Inter Switch Menu is closed .

If only 2 display units are installed but the interswitch is set for 3
i or more display units, the Inter Switch Menu for 3 or more
display units will appear.

Inter Switch Menu (with 3 or More Display Units)

a. Connected
scanner unit

b. Display unit
connected as
master

c. Display unit
connected as
slave

f. Set
d. Name

e. File
g. Exit
Operations

a. Connected scanner unit

In mode for naming a display unit or antenna unit, clicking on a unit opens the name input
window.

A
A－ 5
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION

b. Display unit connected as master

c. Display unit connected as slave
If this button is clicked, select / cancel the display unit.

If this button is clicked in the naming a display unit or scanner unit mode , the name input
window is opened .

d. Name
If this button is clicked, set to the display or scanner unit rename mode.

e. File Operations
If this button is clicked, the File Operations menu is opened.。

f. Set
If this button is clicked, the change of connection is determined.

g. Exit
If this button is clicked, the Inter Switch Menu is closed .

A.2.3 Change of Connection Pattern (with 2 Display Units)

If two display units are installed, a connection pattern needs to be selected.

Procedures
1) Open the Inter Switch menu (with 2 Display Units).

2) Move the cursor onto the Connection pattern (see Section A.2.2 "Inter
Switch Menu" and Section a. "Connection pattern") to be changed , and left-click.

The connection pattern will be selected, and 3. Set (Section b. "Set") will blink.

3) Left-click the 3. Set button.

The connection pattern will be changed.

A－ 6
 JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION

A.2.4 Change of Connection Pattern (with 3 or More Display

Units)
If three or more display units are installed, the layout of connection patterns needs
to be set.

Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).

2) Move the cursor onto the display unit (Section b. "Display unit connected as
master" or Section c. "Display unit connected as slave") to be changed , and left-
click.
The selected display unit will be highlighted.

To deselect the display unit, left-click key again.

3) Move the cursor to the change-destination display unit, and left-

click.
he selected display unit in step 2 will be switched to the change-destination display unit, and
3. Set (Section f. "Set") will blink.

If the change destination is empty, control will move and 3. Set will blink.

4) Left-click the 3. Set button.

The connection pattern will be changed.

A master display unit is always necessary for establishing a

i slave connection.

A
A－ 7
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION

A.2.5 Operating Connection Pattern Files (File Operations)

Frequently used connection patterns can be read easily by saving interswitch
connection patterns.

[1] Loading connection patterns (Load)

Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).

2) Left-click the 2. File Operation button.

The File Operations menu will appear.

3) Left-click the 3. Load button.

Currently saved connection patterns in memory will be listed.

4) Left-click the button corresponding to the file to be loaded.

Confirmation Window will appear.

5) Left-click the 1. Yes to load.

The connection pattern will be changed.

[2] Saving connection patterns (Save)

Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).

2) Left-click the 2. File Operation button.

The File Operations window will appear.

3) Left-click the 2. Save button.

The Save menu will appear.

Currently saved connection patterns in memory will be listed.

4) Left-click the button corresponding to the file to be saved.

The Input File Name window will appear.

5) Enter the file name to be saved.

Up to 8 characters can be entered.For the input method on the character input screen, see
Section 3.3.4.7 "Entering a character".

The connection pattern will be saved when the name is input.

A－ 8
 JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION

[3] Erasing a connection pattern (Erase)

Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).

2) Left-click the 2. File Operation button.

The File Operations window will appear.

3) Left-click the 3. Erase button.

The Erase menu will appear.

The list of connection patterns stored in the memory will be displayed.

4) Left-click the button corresponding to the file to be erased.

Confirmation Window will appear.

5) Left-click the 1. Yes to load.

The selected connection pattern is erased and the file name is deleted from the list.

A.2.6 Names of Display Units and Scanner Units

The display units and antenna units can be named.

Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).

2) Left-click the 1. Name button.

"Name" will be highlighted, indicating that the rename mode is activated.

3) Move the cursor to the display unit (Section b. "Display unit connected as
or scanner unit (Section a.
master" or Section c. "Display unit connected as slave")
"Connected scanner unit") to be renamed , and left-click.
he Input IND Name or the Input TXRX Name window will appear.

4) Input a new unit name.

Up to 8 characters can be input as a unit name. For the input method on the character input
menu, see Section 3.3.4.7 "Entering a character".

The selected display unit or antenna unit will be renamed when the new name is input.

A
A－ 9
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCE

A.3 REFERENCE

A.3.1 Preheat Time after Change of Connection Pattern

After the current interswitch connection pattern has been changed, operation
needs to wait until the system is ready. This is because the preheat time varies
depending on the previous connection of the scanner unit and display unit.

The wait time is necessary for protecting the electronic tubes that emit radio
waves.

a) When not changed to a new connection pattern Preheating not

required
b) When changed to a new connection pattern and an Preheating not
scanner unit had been used before the change required
c) When changed to a new connection pattern and an Preheating
scanner unit had not been used before the change required

A.3.2 Notes on Changing Connection Pattern

An attempt to change to another connection pattern immediately after the
completion of connection pattern change may fail.

This is because internal processing still needs some preparation time upon
completion of connection pattern change. Let several seconds pass between
connection pattern change operations.

A.3.3 Notes on Connecting Slave Display Unit

Before a slave display unit can be placed in transmission state, the master display
unit must be placed in transmission state. If the master display unit is moved from
the transmission state to the transmission standby state, the slave display unit is
forcibly placed in transmission standby state. When they are in transmission
standby state, TXRX Standby is shown in the alarm indication (lower right of the
display), and the alarm sounds.

A slave display unit cannot control tune. Tune is controlled by the master display
unit. Slave is shown in the transmitter pulse length (upper left of the display).

Range change for a slave display unit is limited by the range and pulse length /
repetition frequency of the master display unit. As a rule, a greater range than the
range of the master display unit cannot be set for a slave display unit. However, if
the transmitter pulse length of a slave display unit is identical to the master
display unit's and the repetition frequency is within the master display unit's, a
greater range than the master display unit's can be selected for the slave display
unit. When the master display unit narrows the range or changes the transmitter

A －10
 JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCE

pulse length, the range of the slave display unit may be forcibly changed. In this
case, Master Range CHG is shown in the alarm indication (lower right of the
display), and the alarm sounds.

A.3.4 Setting at Installation

Setting of the interswitch circuit (CCL-304*)

The settings of the DIP switches SW11 to SW13 are shown below.

SW 11 SW 13 SW 12

Interswitch circuit PCB

CCL-304*

1) SW11 setting (extension mode and master/slave settings)

1 2 3 4

ON

OFF

Extension mode setting

4 Description
Set the switch to OFF if the
ON Extension mode number of connected display
units is four or less.
OFF Normal mode

Master/slave setting

3 Description
Set the switch to ON if the
ON Slave slave ISW PCB is selected in
extension mode.
OFF Master

Unused

1, 2 Description
Set the switch to OFF in
ON Unused
normal state.
OFF Unused

A
A－ 11
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCE

2) SW12 setting (radar connection settings)

1 2 3 4 5 6 7 8

ON

OFF
Radar connection settings

ON No.8 display unit connected

8
OFF No.8 display unit not connected

ON No.7 display unit connected

7
OFF No.7 display unit not connected

ON No.6 display unit connected

6
OFF No.6 display unit not connected

ON No.5 display unit connected

5
OFF No.5 display unit not connected

ON No.4 display unit connected

4
OFF No.4 display unit not connected

ON No.3 display unit connected

3
OFF No.3 display unit not connected

ON No.2 display unit connected

2
OFF No.2 display unit not connected

ON No.1 display unit connected

1
OFF No.1 display unit not connected

3) SW13 (unused)
1 2 3 4

ON

OFF

1,2,3,4 Unused (All OFF)

Before the DIP switches of the interswitch circuit can be set, the
interswitch breaker must be turned off in order to ensure safety
operation.

A －12
 Appendix B
DRAWINGS

DRAWINGS
B.1 Interconnection Diagram of Display Unit ........................................... B-1
B.1.1 NCD-4990 ........................................................................................ B-2
B.1.2 NCD-4990 w/NBA-5135 ................................................................... B-3
B.1.3 NCD-4990T ...................................................................................... B-4
B.1.4 NCD-4990T w/NBA-5135 ................................................................ B-5
B.1.5 NWZ-170-R ...................................................................................... B-6
B.1.6 NWZ-170-RT .................................................................................... B-7
B.1.7 NCE-5163-R ..................................................................................... B-8
B.1.8 NCE-5163-RT ................................................................................... B-9
B.1.9 NBA-5135 ...................................................................................... B-10
B.2 Power System Daigram of Display Unit ........................................... B-11
B.3 Signal Flow Diagram of Display Unit ................................................ B-12
B.4 Primary Power System Diagram ....................................................... B-13
B.5 Block Diagram of Scanner Unit ........................................................ B-14
B.5.1 NKE-2103 ...................................................................................... B-15
B.5.2 NKE-2254 ...................................................................................... B-16
B.5.3 NKE-1125/NKE-1130 ..................................................................... B-17
 B.5.4 NKE-1129, NTG-3225 / NKE-1139, NTG-3230 ............................. B-18
B.6 Interconnection Diagram of Scanner Unit ....................................... B-19
B.6.1 NKE-2103 ...................................................................................... B-20
B.6.2 NKE-2254 ...................................................................................... B-21
B.6.3 NKE-1125 (AC110V) ...................................................................... B-22
B.6.4 NKE-1125 (AC220V) ...................................................................... B-23
B.6.5 NKE-1129 (AC110V) ...................................................................... B-24
B.6.6 NKE-1129 (AC220V) ...................................................................... B-25
B.6.7 NTG-3225 ...................................................................................... B-26
B.6.8 NKE-1130 (AC110V) ...................................................................... B-27
B.6.9 NKE-1130 (AC220V) ...................................................................... B-28
B.6.10 NKE-1139 (AC110V) ...................................................................... B-29
B.6.11 NKE-1139 (AC220V) ...................................................................... B-30
B.6.12 NTG-3230 ...................................................................................... B-31
B.7 Terminal Board Connection Diagram ............................................... B-32
B.7.1 JMA-9110-6XA/JMA-9110-6XAH .................................................. B-33
B.7.2 JMA-9110-6XA/JMA-9110-6XAH (desktop) ................................. B-34
B.7.3 JMA-9122-6XAH ............................................................................ B-35
B.7.4 JMA-9122-6XAH (desktop) ........................................................... B-36
B.7.5 JMA-9122-6XA/9XA ...................................................................... B-37
B.7.6 JMA-9123-7XA/9XA ...................................................................... B-38
B.7.7 JMA-9132-SA ................................................................................ B-39
B.7.8 JMA-9133-SA ................................................................................ B-40
B.7.9 NCD-4990T .................................................................................... B-41
B.8 GYRO I/F ............................................................................................. B-42
B.9 Inter Switch Unit ................................................................................. B-44
B.9.1 Terminal Board Connection Diagram ......................................... B-44
B.9.2 Interconnection Diagram ............................................................. B-46
 JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit

B.1 Interconnection Diagram of Display Unit

B
B－ 1
 MONITOR UNIT
NWZ-170-R
*OPTION OPERATION UNIT
(USER SUPPLY) NCE-5163-R
*PS/2 MOUSE/TRK BAL L
(U SER SUPPL Y)
OPERATION OPERATION
LCD PANEL CIRCUIT B CIRCUIT A
H-7WSRD0002A CCK-974 CCK-973
PC620 PC610
A1
7P 14P 15P
J6201 J6101 J6102
SP1
CCK -972 PC710
OPERATION
CIRCUIT

*PS/2 EX TENSION CA BLE

LCD

(U SER SU PPLY )
8P
J711

Fig B-1: Interconnection Diagram of NCD-4990

8P
H-7ZCR D1328 6P 6P 2P 7P 14P 14P 15P
J 6411 J6408 J6406 J6405 J6404 J6403 J6402
9P 2m H -7ZCRD 1329A (N W Z-170-R ) OPERATION CIRCUIT D
B.1 Interconnection Diagram of Display Unit

CCK-976
6P 6P 30P
J 6410
PC640
J6409 J 6401
AC 2m 5ZCG H 00285 (N WZ-170-R)

D VI 2m H -7ZCRD 1345 (N W Z-170-R)

RADAR PROCESS UNIT AIS PROCESS

CIRCUIT
NDC-1399-9
15P
64P
J 4409
V GA J4403
CDC-1325 2m H -7ZC RD 1337 (N CE-5163-R )
15P 64P
J 4405 J4601
PC460 JR C SU PPLY
V GA

B－ 2
28P
J 4406
ARPA PROCESS
D VI-D CIRCUIT
64P
J4404 9P TO O PU
8P
J 4407 CDC-1186D *OPTION B101
J4309 30P
R J-45 64P J4311
J4501
PC450
3P
50P J4313 TO SUB O PU
J 4408 30P
C F-c ard
B102 J4312
3P
RADAR PROCESS
11P
J4314
GYRO INTERFACE

INTERSWITCH UNIT
TB914 TO TRU
CIRCUIT CIRCUIT 15P
CH1 26P
14P
TB4101

NQE-3141-2A
TB913 J4306
CMJ-462E TO ISW
CDC-1324 PC420
11P
TB912
26P
J4307
26P
TB4201
CH2
PC440
>

AC O UT2 2P
15P
64P 64P 64P 2P
B.DRAWINGS

TB911 T O EXT-RA DAR

J4401 J 4402 J1 J4308
B ATTERY 2P 30P
+

POWER SUPPLY
ー
IN 2P
TB905
TERMINAL BOARD TB4401
PC900
SCA NN ER MOTOR
U AC O UT2 CQD-2097 TO SEN SOR

CBD-1661
20P W 401 H -7ZCRD 1339 22P
NCD-4990

PC430
POW ER V 50P TB4501
J4301
W 50P
64P 64P 64P 64P J4105 TO A LAR M SYSTEM
J4101 J 4102 J4104 J4103 22P
W 402 H -7ZCRD 1339 TB4601
>

50P
18P
J4302
MOTHERBOARD 50P
TO G YRO
JMA-9100 Instruction Manual

J4106 6P
TB4701
R ED W 403 H -7ZCRD 1339
CQC-1192
20P 50P
WHT 8P

AC IN
J4108 J4303
BL U 50P T O L OG
PC410 J4107 12P
TB4801
18P
J4304
TO PC
9P
8P J4310
J4305
R ED 4351A07335 FILTER
U U
BL U
W OU T IN W AC 100-115V 50/60H z
B.1.1 WHT
V V
AC 220-240V 50/60H z
NCD-4990（自立型） 機内接続図
JMA-9122-6/9XA,JMA-9123-7/9XA,JMA-9132-SA,JMA-9133-SA
Interconnection diagram of DISPLAY UNIT type NCD-4990(self standing)
 B
MONITOR UNIT
NWZ-170-R
*OPTION OPERATION UNIT
B.1 Interconnection Diagram of Display Unit

(USER SUPPLY)
*PS/2 MOUSE/TRK BAL L
NCE-5163-R
(U SER SUPPL Y)
OPERATION OPERATION
LCD PANEL CIRCUIT B CIRCUIT A
H-7WSRD0002A CCK-974 CCK-973
PC620 PC610
A1
7P 14P 15P
J6201 J6101 J6102
SP1
CCK -972 PC710

Fig B-2: Interconnection Diagram of NCD-4990 w/NBA-5135

OPERATION
CIRCUIT

*PS/2 EX TENSION CA BLE

L CD

(U SER SU PPLY )
8P
J711
8P
H-7ZCR D1328 6P 6P 2P 7P 14P 14P 15P
J 6411 J6408 J6406 J6405 J6404 J6403 J6402
9P 2m H -7ZCRD 1329A (N W Z-170-R ) OPERATION CIRCUIT D
CCK-976
6P 6P 30P
J 6410
PC640
J6409 J 6401
>

AC 2m 5ZCG H 00285 (N WZ-170-R)

D VI 2m H -7ZCRD 1345 (N WZ-170-R)

RADAR PROCESS UNIT

B.DRAWINGS

AIS PROCESS
NDC-1399-9 15P
J 4409
64P
J4403
CIRCUIT
V GA
CDC-1325 2m H -7ZC RD 1337 (N CE-5163-R )
15P
J 4405
64P
J4601
PC460 JR C SU PPLY
V GA

B－ 3
28P
J 4406
ARPA PROCESS
CIRCUIT
>

D VI-D
WHT
RED

64P
J4404 9P TO OPU
JMA-9100 Instruction Manual

8P
U V FG J 4407 CDC-1186D *OPTION B101
J4309 30P
J4311
R J-45 64P
PC450
NCD-4990 w/NBA-5135

J4501
TB522 50P
3P
J4313 TO SUB OPU
AC IN J 4408
B102 30P
C F-c ard J4312
3P
RADAR PROCESS
11P
J4314
GYRO INTERFACE
W406 H-7ZCRD 1342A

TB914

INTERSWITCH UNIT
TO TRU
CIRCUIT CIRCUIT 15P
CH1 26P
14P
TB4101
CONVERTER UNIT

NQE-3141-2A
TB913 J4306
CMJ-462E TO ISW
CDC-1324 PC420 11P
TB912
26P
J4307
26P
TB4201
CH2
AC OUT2 2P
PC440
NBA-5135

15P
64P 64P 64P 2P
TB911 T O EXT-RA DAR
AC/DC

J4401 J 4402 J1 J4308

B ATTERY 2P 30P
+

POWER SUPPLY
ー
IN 2P
TERMINAL BOARD TB4401
PC900 TB905
R ED
U AC OUT2 CQD-2097 TO SEN SOR

CBD-1661
WHT 20P W 401 H -7ZCRD 1339 22P
V
W
50P
J4301 PC430 TB4501
50P
64P 64P 64P 64P J4105 TO A LAR M SYSTEM
J4101 J 4102 J4104 J4103
TB521 W 402 H -7ZCRD 1339
22P
TB4601
50P
DC24V OUT 18P
J4302
+ ー FG
MOTHERBOARD 50P
J4106
TO G YRO
6P
TB4701
R ED W 403 H -7ZCRD 1339
CQC-1192
20P 50P
WHT 8P

AC IN
J4108 J4303
BL U 50P T O L OG
PC410 J4107 12P
TB4801
18P
J4304
SCAN NER MO TOR TO PC
POWER D C24V 9P
8P J4310
J4305
R ED 4351A07335 FIL TER
U U
BL U
W OU T IN W AC 100-115V 50/60H z
B.1.2 WHT
V V
AC 220-240V 50/60H z
NCD-4990（自立型） 機内接続図
JMA-9110-6XA,JMA-9110-6XAH,JMA-9122-6XAH
Interconnection diagram of DISPLAY UNIT type NCD-4990(self standing)
 MONITOR UNIT
NWZ-170-RT
*OPTION OPERATION UNIT
(USER SUPPLY)
*PS/2 MOUSE/TRK BAL L
NCE-5163-RT
(U SER SUPPL Y)
OPERATION OPERATION
LCD PANEL CIRCUIT B CIRCUIT A
H-7WSRD0002A CCK-974 CCK-973
PC620 PC610
A1
7P 14P 15P
J6201 J6101 J6102
SP1
CCK -972 PC710
OPERATION
CIRCUIT

*PS/2 EX TENSION CA BLE

L CD

(U SER SU PPLY )
8P
J711

Fig B-3: Interconnection Diagram of NCD-4990T

8P
H-7ZCR D1328 6P 6P 2P 7P 14P 14P 15P
J 6411 J6408 J6406 J6405 J6404 J6403 J6402
9P 5m H -7ZCRD 1330A (N W Z-170-R T) OPERATION CIRCUIT D
B.1 Interconnection Diagram of Display Unit

CCK-976
6P 6P 30P
J 6410
PC640
J6409 J 6401
AC 5m 5ZCG H 00364 (N WZ-170-RT)

D VI 5m H -7ZCRD 1346 (N WZ-170-RT)

RADAR PROCESS UNIT AIS PROCESS

NDC-1399-9T 15P
J 4409
64P
J4403
CIRCUIT
V GA
CDC-1325 5m H -7ZC RD 1338 (N CE-5163-R T)
15P
J 4405
64P
J4601
PC460 JR C SU PPLY
V GA

B－ 4
28P
J 4406
ARPA PROCESS
D VI-D CIRCUIT
64P
J4404 9P TO OPU
8P
J 4407 CDC-1186D *OPTION B101
J4309 30P
J4311
R J-45 64P
PC450
J4501 3P
50P J4313 TO SUB OPU
J 4408 30P
C F-c ard
B102 J4312
3P
RADAR PROCESS
11P
J4314
GYRO INTERFACE TB914

INTERSWITCH UNIT
TO TRU
CIRCUIT CIRCUIT 15P
CH1 26P
14P
TB4101

NQE-3141-2A
TB913 J4306
CMJ-462E TO ISW
CDC-1324 PC420 11P
TB912
26P
J4307
26P
TB4201
CH2
AC OUT2 2P
PC440
>

15P
64P 64P 64P 2P
TB911 T O EXT-RA DAR
B.DRAWINGS

J4401 J 4402 J1 J4308

B ATTERY 2P 30P
+

POWER SUPPLY
ー
IN 2P
TERMINAL BOARD TB4401
PC900 TB905
CQD-2097
NCD-4990T

U AC OUT2 TO SEN SOR

CBD-1661
SCAN NER MOTO R 20P W 401 H -7ZCRD 1339 22P
POW ER
V
W
50P
J4301 PC430 TB4501
50P
64P 64P 64P 64P J4105 TO A LAR M SYSTEM
J4101 J 4102 J4104 J4103 22P
W 402 H -7ZCRD 1339 TB4601
50P
18P
>

J4302
MOTHERBOARD 50P
J4106
TO G YRO
JMA-9100 Instruction Manual

6P
TB4701
R ED W 403 H -7ZCRD 1339
CQC-1192
WHT 20P 50P
8P

AC IN
J4108 J4303
BL U 50P T O L OG
PC410 J4107 12P
TB4801
1 2 3 18P
J4304
TB 402 TO PC
9P
1 2 3 8P J4310
J4305
R ED

WH T

BL U
RED
U 4351A07335 FIL TER U
BL U
W OU T IN W AC 100-115V 50/60H z
B.1.3 W 405 H -7ZC RD1341A WHT
V V
AC 220-240V 50/60H z
NCD-4990T（卓上型） 機内接続図
JMA-9122-6/9XA,JMA-9123-7/9XA,JMA-9132-SA,JMA-9133-SA
Interconnection diagram of DISPLAY UNIT type NCD-4990T(desktop)
 B
MONITOR UNIT
NWZ-170-RT
*OPTION OPERATION UNIT
B.1 Interconnection Diagram of Display Unit

(USER SUPPLY)
*PS/2 MOUSE/TRK BAL L
NCE-5163-RT
(U SER SUPPL Y)
OPERATION OPERATION
LCD PANEL CIRCUIT B CIRCUIT A
H-7WSRD0002A CCK-974 CCK-973
PC620 PC610
A1
7P 14P 15P
J6201 J6101 J6102
SP1
CCK -972 PC710

Fig B-4: Interconnection Diagram of NCD-4990T w/NBA-5135

OPERATION
CIRCUIT

*PS/2 EX TENSION CA BLE

L CD

(U SER SU PPLY )
8P
J711
8P
H-7ZCR D1328 6P 6P 2P 7P 14P 14P 15P
J 6411 J6408 J6406 J6405 J6404 J6403 J6402
9P 5m H -7ZCRD 1330A (N W Z-170-R T) OPERATION CIRCUIT D
CCK-976
6P 6P 30P
J 6410
PC640
J6409 J 6401
>

AC 5m 5ZCG H 00364 (N WZ-170-RT)

D VI 5m H -7ZCRD 1346 (N WZ-170-RT)

RADAR PROCESS UNIT

B.DRAWINGS

AIS PROCESS
NDC-1399-9T 15P
J 4409
64P
J4403
CIRCUIT
V GA
CDC-1325 5m H -7ZC RD 1338 (N CE-5163-R T)
15P
J 4405
64P
J4601
PC460 JR C SU PPLY
V GA

B－ 5
BL K

28P
ARPA PROCESS
WH T

J 4406
G RN

CIRCUIT
>

D VI-D
64P
J4404 9P TO OPU
JMA-9100 Instruction Manual

8P
NCD-4990T w/NBA-5135

U V FG J 4407 CDC-1186D *OPTION B101

J4309 30P
J4311
R J-45 64P
PC450
J4501
TB522 50P
3P
J4313 TO SUB OPU
AC IN J 4408 30P
W407 H-7ZCRD 1343A

C F-c ard
B102 J4312
3P
RADAR PROCESS
11P
J4314
GYRO INTERFACE TB914

INTERSWITCH UNIT
TO TRU
CIRCUIT CIRCUIT 15P
CH1 26P
14P
TB4101
CONVERTER UNIT

NQE-3141-2A
TB913 J4306
CMJ-462E TO ISW
CDC-1324 PC420 11P
TB912
26P
J4307
26P
TB4201
CH2
AC OUT2 2P
PC440
NBA-5135

15P
64P 64P 64P 2P
TB911 T O EXT-RA DAR
AC/DC

J4401 J 4402 J1 J4308

B ATTERY 2P 30P
+

POWER SUPPLY
ー
IN 2P
TERMINAL BOARD TB4401
PC900 TB905
WHT
U AC OUT2 CQD-2097 TO SEN SOR

CBD-1661
B LK 20P W 401 H -7ZCRD 1339 22P
G RN
V
W
50P
J4301 PC430 TB4501
50P
64P 64P 64P 64P J4105 TO A LAR M SYSTEM
J4101 J 4102 J4104 J4103
TB521 W 402 H -7ZCRD 1339
22P
TB4601
50P
DC24V OUT 18P
J4302
+ ー FG
MOTHERBOARD 50P
J4106
TO G YRO
6P
TB4701
GR N R ED W 403 H -7ZCRD 1339
CQC-1192
WHT 20P 50P
W408 H -7ZC RD 1344A 8P

AC IN
J4108 J4303
BL U 50P T O L OG
PC410
GR N J4107 12P
TB4801
1 2 3 1 2 3 18P
J4304
TB401 TB 402 TO PC
9P
1 2 3 1 2 3 8P J4310
J4305
R ED

WH T

BL U
RED
U 4351A07335 FIL TER U
BL U
W OU T IN W AC 100-115V 50/60H z
B.1.4 SCAN NER MO TOR

W 405 H -7ZC RD1341A WHT

V V
AC 220-240V 50/60H z
NCD-4990T（卓上型） 機内接続図
POWER D C24V
JMA-9110-6XA,JMA-9110-6XAH,JMA-9122-6XAH
Interconnection diagram of DISPLAY UNIT type NCD-4990T(desktop)
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit

B.1.5 NWZ-170-R

H-7WSRD0002A

LCD

CCK-972
PC710

FAN
RGB DVI ALM
AC 1 00V
24 0V
BRILL J7101
AC 2m VM0301-VM0303B2Mｸﾛ
DVI 2m H-7ZCRD1345

9P 2m H-7ZCRD1329A

FL1

8P
H-7ZCRD1328
CDC-1324

CQD-2097

CBD-1661
OUTLET
J4406

J4309

CML-764-R (NWZ-170-R)

Monitor Unit Interconnection

Fig B-5: Interconnection Diagram of NWZ-170-R

B－ 6
 JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit

B.1.6 NWZ-170-RT

H-7WSRD0002A

LCD

CCK-972
PC710

FAN
RGB DVI ALM
AC 1 00V
24 0V
BRILL J7101
AC 5m VM0301-VM0303B5Mｸﾛ
DVI 5m H-7ZCRD1346

9P 5m H-7ZCRD1330A

FL1

8P
H-7ZCRD1328
CDC-1324

CQD-2097

CBD-1661
OUTLET
J4406

J4309

CML-764-RT (NWZ-170-RT)

Monitor Unit Interconnection

Fig B-6: Interconnection Diagram of NWZ-170-RT

B
B－ 7
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit

B.1.7 NCE-5163-R

OPERATION UNIT
NCE-5163-R

OPERATION OPERATION
CIRCUIT B CIRCUIT A
CCK-974 CCK-973
PC620 PC610

A1

7P 14P 15P
J6201 J6101 J6102
SP1

W63 H-7ZCRD1333A
W62 H-7ZCRD1332

W64 H-7ZCRD1334
W65 H-7ZCRD1335

6P 6P 2P 7P 14P 14P 15P

J6411 J6408 J6406 J6405 J6404 J6403 J6402

OPERATION CIRCUIT D
CCK -976
PC 640
6P 6P 2P 30P
J6410 J6409 J6407 J6401

FL1

W67 2m H-7ZCRD1337

CMD-996-R (NCE-5163-R)

Operation Unit Interconnection

Fig B-7: Interconnection Diagram of NCE-5163-R

B－ 8
 JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit

B.1.8 NCE-5163-RT

OPERATION UNIT
NCE-5163-RT

OPERATION OPERATION
CIRCUIT B CIRCUIT A
CCK-974 CCK-973
PC620 PC610

A1

7P 14P 15P
J6201 J6101 J6102
SP1

W63 H-7ZCRD1333A
W62 H-7ZCRD1332

W64 H-7ZCRD1334
W65 H-7ZCRD1335

6P 6P 2P 7P 14P 14P 15P

J6411 J6408 J6406 J6405 J6404 J6403 J6402

OPERATION CIRCUIT D
CCK -976
PC 640
6P 6P 2P 30P
J6410 J6409 J6407 J6401

FL1

W68 5m H-7ZCRD1338

CMD-996-RT (NCE-5163-RT)

Operation Unit Interconnection

Fig B-8: Interconnection Diagram of NCE-5163-RT

B
B－ 9
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit

B.1.9 NBA-5135

W6 H-7ZCRD1499

1 2 3 1 2 3

1
TB521

2 3
FS1 1
TB 522

2 3

RED BLK BLK

W1 H-7ZCRD1495 WHT WHT

WHT

W2 H-7ZCRD1496 W5 H-7ZCRD1499
Twisted
W4 H-7ZCRD1498
RED WHT
BLK

U V + + + - - -

FL1 A1
LF-210 AES300-24B
W3 H-7ZCRD1497

u FG v N L FG

RED BLK WHT

WHT
RED

BLK
Twisted

BLK

CBD-1684A (NBA-5135)

AC/DC Converter Interconnection

Fig B-9: Interconnection Diagram of NBA-5135

B －10
 B
Power System Daigram of Display Unit

MONITOR UNIT
NWZ-170-R
B.2 Power System Daigram of Display Unit

*OPTION OPERATION UNIT

(USER SUPPLY)
*PS/2 MOUSE/TRK BAL L
NCE-5163-R
(U SER SUPPL Y)
OPERATION OPERATION
LCD PANEL CIRCUIT B CIRCUIT A
H-7WSRD0002A CCK-974 CCK-973
PC620 PC610
A1
7P 14P 15P
J6201 J6101 J6102
SP1
CCK -972 PC710
OPERATION

+5V
CIRCUIT

*PS/2 EX TENSION CA BLE

L CD

(U SER SU PPLY )

Fig B-10: Power System Diagram of NCD-4990/T

8P
J711
U,V
AC100-115V 8P
H-7ZCR D1328 6P 6P 2P 7P 14P 14P 15P
AC220-240V J 6411 J6408 J6406 J6405 J6404 J6403 J6402
50/60H z,1φ
9P 2m H -7ZCRD 1329A (N WZ-170-R ) OPERATION CIRCUIT D
CCK-976
>

6P 6P 30P
J 6410
PC640
J6409 J 6401
B.DRAWINGS

AC 2m 5ZCG H00285 (N WZ-170-R )

D VI 2m H-7ZCRD 1345 (N W Z-170-R)

RADAR PROCESS UNIT AIS PROCESS

NDC-1399-9 15P
J 4409 64P
CIRCUIT
JMA-9110-6XA J4403
5V
V GA
CDC-1325 2m H -7ZC RD 1337 (N CE-5163-R )
JMA-9110-6XAH 15P 64P
PC460 P+12V
5m H -7ZC RD 1338 (N CE-5163-R T)

B－ 11
J 4405 J4601 JR C SU PPLY
JMA-9122-6XAH V GA
only 28P
ARPA PROCESS
DC+24V
>

J 4406
D VI-D CIRCUIT
WHT
RED
JMA-9100 Instruction Manual

64P
3.3V
J4404 9P TO OPU
8P
U V FG J 4407 CDC-1186D *OPTION B101
J4309 30P
J4311
R J-45 64P
PC450
U,V +48V
J4501
TB522 50P
3P
TO SUB OPU
J4313
AC IN J 4408
B102
30P
AC100-115V C F-c ard
3P (to SCANNER
J4312
UNIT)
RADAR PROCESS
AC220-240V 11P
J4314
GYRO INTERFACE
W 406 H-7ZCRD 1342A

TB914 TO TRU

INTERSWITCH UNIT
50/60Hz,1φ
CIRCUIT CIRCUIT 15P CH1 26P
14P
TB4101
CONVERTER UNIT

TB913 J4306

NQE-3141-2
CMJ-462E TO ISW
CDC-1324 PC420
11P
TB912
26P
J4307
26P
TB4201
AC OUT2 2P
PC440 CH2
NBA-5135

DC+24V
15P
64P 64P 64P 2P
TB911 T O EXT-RA DAR
AC/DC

J4401 J 4402 J4308

P+12V
J1
P+5V
+ B ATTERY 2P 30P

POWER SUPPLY
ー
IN
3.3V,5V, 2P
TB905
TERMINAL BOARD TB4401
PC900
12V,-12V CQD-2097
R ED
U AC OUT2 TO SEN SOR

CBD-1661
W HT 20P 22P
PC430
V W401 H -7ZCRD 1339
50P TB4501
W
64P 64P 64P 64P
50P
J4105

J4301
P+5V TO A LAR M SYSTEM
J4101 J 4102 J4104 J4103
TB521 22P
DC24V OUT U,V 18P
W402 H -7ZCRD 1339
50P
J4302
TB4601
+ FG
AC100-115V MOTHERBOARD 50P
J4106
TO G YRO
3.3V,5V,12V,-12V
ー 6P
AC220-240V
TB4701
50/60Hz,1φR ED W403 H -7ZCRD 1339
+48V,DC+24V 50P
20P
CQC-1192
3.3V,5V,12V,-12V
W HT 8P

AC IN
J4303
+24V
J4108 T O L OG
BL U 50P
PC410
12P
J4107
TB4701
SCAN NER MOTOR

18P
3.3V,5V,12V,-12V
J4304
TO PC
+48V,DC+24V
B.2 POWER D C24V
INPUT VOLTAGE
SELECT SWITCH

R ED
BL U
W HT

U
W OU T
V

4351A07335 FIL TER

IN W

U
V

AC 100-115V 50/60H z
AC 220-240V 50/60H z

8P
J4305
NCD-4990 電源系統図

9P
J4310
Power supply system diagram of DISPLAY UNIT type NCD-4990(self standing)
 MONITOR UNIT
NWZ-170-R
OPERATION UNIT
Signal Flow Diagram of Display Unit

*OPTION
(USER SUPPLY)
*PS/2 MOUSE/TRK BAL L
NCE-5163-R
(U SER SUPPL Y)
OPERATION OPERATION
LCD PANEL CIRCUIT B CIRCUIT A
H-7WSRD0002A CCK-974 CCK-973
PC620 PC610
A1
7P 14P 15P
J6201 J6101 J6102
SP1
CCK -972 PC710
OPERATION
CIRCUIT

*PS/2 EX TENSION CA BLE

PS/2
L CD

PS/2
(U SER SU PPLY ) Audio Power SW KEY matrix
8P I/F I/F Encoder

Fig B-11: Signal Flow Diagram of NCD-4990/T

J711
8P
Dimmer
H-7ZCR D1328 6P 6P 2P 7P 14P 14P 15P
J 6411 J6408 J6406 J6405 J6404 J6403 J6402
9P 2m H -7ZCRD 1329A (N WZ-170-R ) OPERATION CIRCUIT D
CCK-976
B.3 Signal Flow Diagram of Display Unit

6P 6P 30P
J 6410
PC640
J6409 J 6401
AC 2m 5ZCG H00285 (N WZ-170-R )

D VI 2m H-7ZCRD 1345 (N W Z-170-R)

RADAR PROCESS UNIT Analog RGB AIS PROCESS

NDC-1399-9 15P
J 4409 64P
J4403
CIRCUIT
V GA
CDC-1325 2m H -7ZC RD 1337 (N CE-5163-R )
Analog
15P RGB 64P
PC460 5m H -7ZC RD 1338 (N CE-5163-R T)

B －12
J 4405 J4601 JR C SU PPLY
V GA
Serial
De28P
gital Video Inte rface ARPA PROCESS
J 4406
D VI-D CIRCUIT
WHT
RED

64P LCD Fan Alarm

Ethernet
8P
J4404 9P TO OPU
U V FG J 4407 CDC-1186D *OPTION B101
J4309 30P
J4311
R J-45 64P
J4501
PC450
TB522 50P
3P
TO SUB OPU
J4313
AC IN J 4408
B102
30P Ra dar video
C F-c ard
Rada r video, 3P
J4312
Trigger,Rota
RADAR PROCESS
11P
GYRO INTERFACE Trigger,Rotation J4314
W 406 H-7ZCRD 1342A

TB914 TO TRU

INTERSWITCH UNIT
Se rial
CIRCUIT CIRCUIT 15P CH1 26P
14P
TB4101
CONVERTER UNIT

TB913 J4306

NQE-3141-2
CMJ-462E TO ISW Rada r video,
CDC-1324 PC420
11P
TB912
Rada r video, 26P
J4307
26P
TB4201
Trigger,Rotatio
Trigger,Rotation
PC440 CH2
>

AC OUT2 2P
Radar video,
NBA-5135

15P
64P
Serial,GPIO
64P 2P Radar video,
Trigger,Rotation 64P TB911
B.DRAWINGS

GYRO/LOG T O EXT-RA DAR

AC/DC

J4401 J 4402 J4308

+ B ATTERY 2P
J1
30P Trigger,Rotatio

POWER SUPPLY
ー
IN
2P
TB905
TERMINAL BOARD TB4401
PC900
R ED
U AC OUT2 CQD-2097 TO SEN SOR
Serial

CBD-1661
W HT 20P Rada r Hvideo, 22P
PC430
V W401 -7ZCRD 1339
50P TB4501
W 50P
Trigger,Rotation J4301
64P 64P 64P 64P J4105 TO A LAR M SYSTEM Dry Contact
J4101 J 4102 J4104 J4103
TB521 W402 H -7ZCRD 1339
22P
TB4601
50P
DC24V OUT 18P
GYRO
>

J4302
+ ー FG
MOTHERBOARD 50P
J4106
Serial,GPIO TO G YRO
(STEP/SYN
JMA-9100 Instruction Manual

6P
TB4701
R ED W403 H -7ZCRD 1339
50P LOG
W HT 8P
20P
CQC-1192 GYRO/LOG
(PULSE/SYN

AC IN
J4108 J4303
50P T O L OG
BL U
PC410
12P
J4107
Power supply Control 18P
TB4701
Power supply Fa n alarm J4304
SCAN NER MOTOR TO PC
Serial
B.3 POWER D C24V
R ED
BL U
W HT

U
W OU T
V

4351A07335 FIL TER

IN W

U
V

AC 100-115V 50/60H z
AC 220-240V 50/60H z
Powe r supply Control
Powe r supply Fan alarm

8P
J4305
NCD-4990 信号系統図

9P
J4310
Signal flow diagram of DISPLAY UNIT type NCD-4990
 B
OVER VOLTAGE
B.4 Primary Power System Diagram

PROTECTION
AC100-115V
AC220-240V
50/60Hz,1φ INTERSWITCH=1A
CIRCUIT
Primary Power System Diagram

LINE FILTER P+12V OPERATION UNIT=0.5A(typ)

BREAKER
GYRO I/F CIRCUIT=0.1A(typ)
VOLTAGE SELCT
SWITCH SCANNER
+48V±3V

Fig B-12: Primary Power System Diagram

X BAND_2.5A, S BAND_3.0A
>
B.DRAWINGS

AC100-115V RADAR PROCESS CIRCUIT = 1.2A(typ)

AC220-240V MONITOR UNIT +5.0V ARPA PROCESS CIRCUIT = 0.15A(typ)
50/60Hz,1φ POWER AIS PROCESS CIRCUIT = 0.15(typ)
TERMINAL BOARD = 1.0A(typ)
>

B －13
JMA-9100 Instruction Manual

SCANNER
MOTOR
POWER RADAR PROCESS CIRCUIT = 2.2A(typ)
AC100/230V +3.3V ARPA PROCESS CIRCUIT = 0.1A(typ)
SCAN NER MOTOR
1φ POWER AIS PROCESS CIRCUIT = 0.1(typ)
TERMINAL BOARD = 0.2A(typ)
POWER CONTROL
CIRCUIT
+12V RADAR PROCESS CIRCUIT = 0.1A(typ)
TERMINAL BOARD = 0.4A(typ)
-12V RADAR PROCESS CIRCUIT = 0.1A(typ)

FAN ALM POWER CONTROL

TERMINAL BOARD = 0.1A(typ)
B.4 BATTRY
DC24V
OPERATION UNIT = 0.1A
JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner Unit

B.5 Block Diagram of Scanner Unit

B －14
 JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner Unit

B.5.1 NKE-2103

NKE-2103 Scanner Unit

SLOT ANTENNA

MOTOR ROTARY ΦA,ΦB,ΦZ

ENCODER
B101 JOINT

FILTER

MAG DIODE
V101 LIMITER
RECEIVER

PULSE Tune Control

MIC
TRANS DUMMY
LOAD Receiver
Bandwidth
SWITCHING
Control
CIRCUIT IF AMP
PC 201
Tx Trigger/Pulse Width

VIDEO
AMP
MH
GENERATOR

INTERFACE
POWER CIRCUIT
SUPPLY AVR
CIRCUIT

PC 1001 Status Serial Com, BP, BZ, VD, TRIG

Rotation Control
DC +24V

DC +24V
MOTOR CONTROL
SAFETY SWITCH DC +24V
Speed control POWER S101
PC1501

Fig B-13: Block Diagram of NKE-2103

B
B －15
JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner Unit

B.5.2 NKE-2254

NKE-2254 Scanner Unit

SLOT ANTENNA

MOTOR ROTARY ΦA,ΦB,ΦZ

ENCODER
B101 JOINT

FILTER

MAG DIODE
V101 LIMITER
RECEIVER

PULSE Tune Control

RF AMP
TRANS DUMMY
LOAD Receiver
Bandwidth
SWITCHING Control
CIRCUIT IF AMP
PC 201
Tx Trigger/Pulse Width

VIDEO
AMP
MH
GENERATOR

POWER
INTERFACE CIRCUIT
SUPPLY AVR PC1101
CIRCUIT

PC 1001 Status Serial Com, BP, BZ, VD, TRIG

Rotation Control
DC +24V

DC +24V
MOTOR CONTROL
SAFETY SWITCH DC +24V
Speed control POWER S101
PC1501

Fig B-14: Block Diagram of NKE-2254

B －16
 JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner Unit

B.5.3 NKE-1125/NKE-1130

NKE-1130/NKE-1125 Scanner Unit

SLOT ANTENNA

MOTOR ROTARY ΦA,ΦB,ΦZ

ENCODER
B101 JOINT

ERROR
MOTOR
FILTER
DRIVER
PC1501

MAG DIODE
V101 LIMITER
RECEIVER

PULSE Tune Control

RF AMP
TRANS DUMMY
LOAD Receiver
SWITCHING Bandwidth
Control
CIRCUIT IF AMP
PC 201
Tx Trigger/Pulse Width

VIDEO
AMP
MH
GENERATOR

POWER
INTERFACE CIRCUIT
SUPPLY AVR PC1101
CIRCUIT

PC 1001 Status Serial Com, BP, BZ, VD, TRIG

Relay Control
DC+48V

AC100/110/220 /230V
MOTOR RELAY SAFETY SWITCH 50/60Hz,1φ
PC1201 S101

Fig B-15: Block Diagram of NKE-1125/NKE-1130

B
B －17
JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner Unit

B.5.4 NKE-1129, NTG-3225 / NKE-1139, NTG-3230

NKE-1139/NKE-1129 Scanner Unit

SLOT ANTENNA

MOTOR
MOTOR ROTARY ΦA,ΦB,ΦZ
DRIVER ENCODER
B101 JOINT
PC1501
AC100/110/220/230V
50/60Hz,1φ
ERROR

SAFETY SWITCH Status

S101

NTG-3230 /NTG-3225 FILTER

Transceiver Unit

MAG DIODE LIMITER PIN ATT

V101 / TRHPL (X-band)

RECEIVER
PULSE Tune Control
TRANS RF AMP
DUMMY
LOAD Receiver
Bandwidth
SWITCHING Control
CIRCUIT IF AMP
PC 201
Tx Trigger/Pulse Width

VIDEO
AMP
MH
GENERATOR

INTERFACE CIRCUIT
POWER
PC1101
SUPPLY AVR
CIRCUIT
Serial Com, BP, BZ, VD, TRIG
PC1001
Relay Control
DC+48V

AC100/110 /220/230V
MOTOR RELAY 50/ 60Hz,1φ
PC1201

Fig B-16: Block Diagram of NKE-1129, NTG-3225 / NKE-1139, NTG-3230

B －18
 JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit

B.6 Interconnection Diagram of Scanner Unit

B
B －19
 ANTENNA NAX-16B-4/6
TRANSMITTER/RECEIVER UNIT ＮZT－２１０３ TRANSMITTER/RECEIVER UNIT
A103 A104 INTERCONNECTION
NJC 4002 DUMMY FILTER NJC9952 CMK-599
MAGNETRON
RECEIVER UNIT ＮＲＧ－６１０
V101
A301 E101
MAF1565N NJS6930 NJT1969 (RECEIVER UNIT INTERCONNECTION CMA-823)
A101 A102 IF AMP CIRCUIT (PC301)
S.G. 1.TUNE CAE-529-1
2.+5V
D.L

MAG MIC 3.GND

4.NC
14.MOD ID

1.HMCNT
5.IF

3.COM+
4.COM-
8.AGND

11.HSP

2.AGND
7.+15V

2.+15V
3.MAG.I
1.MPS

13.+8V

4.HTER
5.HVER
2.PW3
3.PW2

6.MBK
5.MCT
4.PW1

2.VDE
3.GND
10.BP

4.PMS
YEL GRN

15.NC

5.GND
2.PTE

7.TXE
9.-7V

3.LVR
12.TI

1.PTI

6.TXI

1.VD
1.TIY
J301

7.BZ
J302

6.C2

J303

J18
F CX68 F CX68

J2

Fig B-17: Interconnection Diagram of NKE-2103

ZCRD1289※

ZCRD1290※

ZCRD1303※

ZCRD1308※
DISPLAY
(W101)

(W102)

(W10６)

(W111)
UNIT
(W204)
WV101 ZCRD1312※
B.6 Interconnection Diagram of Scanner Unit

J202

J203
J201

2.AGND
3.MAG.I

4.PMS
5.GND
4.HTER
5.HVER

2.PTE
14.MOD ID

3.LVR

7.TXE
1.PTI

6.TXI
8.AGND
T201-15

1.TIY
S.G.

7.+15V
1.MPS
2.PW3
3.PW2
4.PW1

6.MBK
5.MCT

7.BZ
6.C2
11.HSP
9.-7V

13.+8V
10.BP

15.NC
CFR-234

12.TI
T201-16 B102
MAG FILTER
CIRCUIT SE
100pF× 3
J1003 (W103) J206

ENCODER CHT -71A

ZCRD1300※
1.MH
1.MH J208
3.MN 3.MN YEL
1.ΦZ

B －20
BLK
(W104) 2.E
ZCRD1301※ BLU
J1002 J205 3.ΦA
WHT
4.ΦB
POWER SUPPLY
1.+15V
2.+12V
1.+15V
2.+12V
MODULATOR CIRCUIT 5.+12V
RED
SHIELD
CIRCUIT 3.+8V 3.+8V (PC201) 6.F.G.
4.AGN D 4.AGND
(PC1001) 5.-15V 5.-15V CME-３６３
6.X1 J8 P8 J81 P81
6.X1
CBD-1783 7.X2 7.X2 1.PTI
1.PTI WHT
8.+5V 8.+5V TB1 2.PTE
2.PTE BLK
9.HTER 9.HTER 3.TXI WHT
10.HV ER 10.HVER 1-2short : Nomal Speed 3.LVR
4.TXE BRN
4.PMS
2-3short : High Speed 5.E
(W105) 6.TXI
J1001 ZCRD1302※ J204 J82 P82
7.TXE 1.LVR BLU

5.ＥＸＢＺ
1.2A 1.2A

6.AGND
2.AGND

4.AGND
3.EXBP
8.NC

1.ETIY
1.MPS

3.MBK
2.MCT

1.C2G
2.PMS RED

2.C2
2.1A 2.1A

1.2A
2.1A

7ZCRD 1280※
J209

J210

J3
3.E BLK

J1
>

(W108)
(W107) Z CRD1305※
ZCRD1304※
B.DRAWINGS

BREAK CIRCUIT CFA-252 SAFETY SWITCH DISPLAY

(W110) ZCRD1307※ WS101
J1503 ZCRD1306※
UNIT

J1501
S.G.

1.MPS

3.MBK
2.MCT
1.2A
2.1A 2 5
NKE-2103

J1504
1.MS1 1 4 PM
2.NC
3.MS2
NJU-85 (OPTION）
>

MOTOR J1505
JMA-9100 Instruction Manual

J125 1.HMCNT
2.+15V
1.MCNT+
2.MCNT- 3.AGND
B101 3.NC
H-7BDRD0048 MOTOR CONTROL POWER CIRCUIT J4
J1502 1.2A H-7ZCRD####*:
(PC1501)
1.M+ 2.1A
DISPLAY “#” means specification document No.
2.NC CBD-1779
MORTOR CBP-202 J5 “*” means revision of the specfication document.
3.M-
1.2A
UNIT
4.NC
2.1A
NKE-2103 / 2103HS
B.6.1 空中線機内接続図
SCANNER UNIT INTERCONNECTION
CAX-10
 B
Ａ103 ANTENNA
NJC4002
Ａ104
RECEIVER UNIT NRG-162A DUMMY FILTER NJC 9952
B.6 Interconnection Diagram of Scanner Unit

Ａ301
NJS6930
RECEIVER CIRCUIT
J101 CMA-866A ③ ③
BM15B-XASS-TE S.G.
12.VD_DC

D.L
10.TGTE

② ① ① ② MAG
14.VDE
13.TNL

Ｖ101
6.-15V
7.+15V

11.TNI
4.TNC

8.GND
9.TGT

15.VD
1.BS3
2.BS2
3.BS1

5.+5V

M1568BS
Ａ101 Ａ102
P3001 NJC 3901M NJ C3901M
CHT-71A

ﾐﾄﾞﾘ

ｷ
(W001)
B102 ZCRD1251※
MODULATOR UNIT NMA-550 (W106)
ZC RD1258※

150Ω MD-12N1 MD-12N1

SE C201

R201 CD202 CD 201

(W003)
P1109 P1110 ZCRD1252※ J2102 0.01UF 1KV
IL-10P
P1111 P2102 (W103) 4 6
J13

Fig B-18: Interconnection Diagram of NKE-2254

1.SHORT 1.SHORT ZCRD1255※
T1
5.MicPS
6.VDINE

P13 IL-6P
11.TRG2
ENCODER

5.TGTE
7.VDIN

1.MONI

2.MAG I
4.TNC

10.GND
7.-15V

9.+15V

2.MAG I
1.BS3
2.BS2
3.BS1

1.RXD
2.TXD

4.GND
8.+5V

4.TGT
3.GSE

6.TNL

YEL
3.+5V
8.TNI

No.2 2 PULSE TANS

2.GS

1.φZ 3.X1 3.X1

BLK
2.φZE 4.X2 4.X2
MODULATOR No.1 1 H-7LPRD0122
(W017)

BLU J1109
3.φ A J1110 J1191 5.TI 5.TI CIRCUIT
IL -G -12P

WHT IL-G-8P 3 5
IL-G -11P CPA-264
J1111

4.φB 6.TIE

8W
IL-4P 6.TIE
RED C202 S.G.
5.+12V 7.+15V J2103 (W104)

P2103
SHIELD 7.+15V 0.22UF 200V
8.G ND 350209-2 ZCRD1256※

ZCRD1257※
6.GND 8.GND CFR-229
9.NC 9.NC J2101 1.X1
1586514-2 MAG FILTER
J1 IL-G -6P 10.NC

(W105)
10.NC 2.X2 CIRCUIT

1.MH

3.MN

2.7KΩ
2.NC
MODULATOR UNIT

0.22UF
1.TIY 11.NC

1/2W
R202
(W004) 220pF× 5

C 203
>

200V
2.TIYE 12.NC ZCRD1253※ INTERCONNECTION
(W207)
3.BP CMB-404
B.DRAWINGS

DISPLAY UNIT

Z CRD1448※ S.G. S.G.

4.BPE P1118 P2101
B3P-SHF

BLU 1 1 BLU

1 2 3

1 2 3
5.BZ

BLK.T
1.HMC NT
J1118

P1303
J1303
2 WHT (W201)

BLK.T
6.BZE 2.+15V WHT 2 (W107)
BLK 3 3 BLK ZCRD1259※ ZCRD1260※
3.GND BREAK C IRCUIT
J2 IL-G -4P

P1503
P1002 J1503 CFA-257

B －21
1.VD T/R CONTROL CIRCUIT J1505 IL-2P-S3E N2

10Ω ,10W
P1103 IL-3P-S3EN2
2.VDE 1.+15V P1003 1.+15V ｱｵ
CMC-1205R

1.MH

3.MN
2.NC
3.MTR+ 2.+12V 4 4 2.+12V 1.HMC NT
ｼﾛ

R1
5 5 2.+15V

B8P-SHF
4.MTR- 3.G ND 3.+8V (W307)

B8P-SHF
ｸﾛ

J1003
J1002

J1103
>

4.GND 6 6 4.GND 3.E ZC RD 1450※

1586514-2 P1505 J125
TB101

P125
MSTBA2.5/11-G 5.-15V 7 7 5.-15V
JMA-9100 Instruction Manual

8 8 B3P-SHF-1AA
1.BP+ 6.10V 6.X1 MOTOR CONTROL 1.MCNT-
(W305) GRN
2.BP- 7.10VE 9 9 7.X2 POWER SUPPLY J1001 YEL
3.BZ+ 8.+5V 10 10 8.+5V 350428-1 POWER CIRCUIT 2.MCNT+
BRN
B101
CIRCUIT

J1301

P1301
4.BZ- 1.M+ 3.NC
1.MC T P1104 P1004 CBD-1779
5.TRIG+ 1.MC T CBD-1682A 2.M-

P1502
P1502 MOTOR

B6P-SHF
2.MBK

B9P-SHF
2.MBK

J1004
6.TRIG- B4P-VH

J1104
3.TISTOP 1 1 (W301) BLU.T
7.MTR+ 3.HSP 1.M+
4.G ND 2 2
8.MTR- 4.HTER 2.NC
5.MPS 3 3 BLK.T
9.MTRE 5.TISTOP 3.M-
4 4 J1501
10.VD+ 6.MIER 6.C 2 J4 J5 J3

ZCRD1451※
IL-G-3P-S3T2-SA 4.NC
11.VD- 7.G ND 350209-1 350209-1 B02P-NV(LF)(SN ）
J1112 J1113 J1114

1.MS1

3.MS2
1.MPS

3.MBK
2.MCT

350209-1
350209-1
2.1A
1.2A

2.1A
1.2A

2.1A
1.2A

2.NC
8.MPS

1.2A
2.1A

1.2A
2.1A
IL-G-9P IL-G-3P IL-G-3P

B3P-VH
(W208)

J1504
50/60ｋW
MOTOR CBP-168A / CBP-182

8.STABY_REQ
J8 9.MIER

J4

J5
J1106 J1105

3.FAN _ERR 2
3.FAN_ERR1
2.HVGATE1
3.TISTOP1
IL-8P IL-G-5P IL-G-2P
※NKE-2254HS
1.HTER1

P1504
ｱｶ太
1.+12V

P1501
1.+12V
2.GND
4.+24V

7.+15V

1.+12V
4.PMS
5.GND

5.GND

4.GND

2.GND
1.PW1
2.PW2
3.PW3

5.CNT
2.PTE

7.TXE
3.LVR

6.+5V
1.PTI

6.TXI

HEATER CONTROL ・MOTOR CBP-182

8.NC

9.NC

2.C 2
DISPLAY UNIT PART

ZCRD 1494※
5 5
6 6
CHG-216
NKE-2254

P1113 P1114 ZCRD1449※

P1105 （OPTION）

WHT
RED
(W302)

(W308
RED
BLU

(W010)

(W009)
YEL
7 7 WHT

（100W）
TR101
(W018) 8 8 RED 2 1

TH101
RED
BLU
YEL
ZCRD1277※ FAN

J1302
B201

P1302
5 4

ｼﾛ太
(W006) (W206) TB105 (W401)
H-7BFRD0002 ZCRD1254※ ZCRD1447※
8 7 ZCRD1508※
FAN

U
U
B202
SAFETY SWITCH

2.PMS
2.PTE

4.TXE

1.LVR
1.PTI

3.TXI
S101
CSD-653

3.E
S-32

V
V
H-7BF RD0002

P82 J 82
P81 J81
SCANNER UNIT INTERCONNECTION

UTH
UTH
CAX-15 WHT.T

WHT
BRN
WHT
BLK

RED
BLU

BLK
S.G. H-7ZCRD####*: NKE-2254 / 2254HS
ZCRD1280※ “#” means specification document No.
B.6.2 “*” means revision of the specfication document. 空中線機内接続図
PM
NJU-85
 A103 ANTENNA
NJC4002
RECEIVER UNIT NRG-162A DUMMY FILTER Ａ104
A301
NJS6930 NJC9952
RECEIVER CIRCUIT CMA-866A
J101 ③ ③
BM15B-XASS-TE S.G.
12.VD_DC

D.L
10.TGTE

② ① ① ② MAG
14.VDE
13.TNL
6.-15V
7.+15V

11.TNI
4.TNC

8.GND

Ｖ101
9.TGT

15.VD
1.BS3
2.BS2
3.BS1

5.+5V

M1568BS
Ａ101 Ａ102
NJC3901M NJ C3901M
P3001
CHT-71A

GRN

YEL
(W001)
B102 Z CRD1251※

Fig B-19: Interconnection Diagram of NKE-1125 (AC110V)

MODULATOR UNIT NMA-550 (W106)
ZC RD1258※

150Ω MD-12N1 MD-12N1

SE C201
(W003)

R201 CD202 CD201

P1109 P1110 ZCRD1252※ J2102 0.01UF 1KV
IL-10P
P1111 P2102 (W103) 4 6
J13 1.SHORT 1.SHORT ZCRD1255※ T1
5.MicPS
6.VDINE

P13 IL-6P
11.TRG2
ENCODER

5.TGTE
7.VDIN

1.MONI

2.MAG I
4.TNC

10.GND
7.-15V

9.+15V

2.MAGI PULSE
1.BS3
2.BS2
3.BS1

1.RXD
2.TXD

4.GND
8.+5V

4.TGT
3.GSE

6.TNL

YEL
3.+5V
8.TNI

2
MODULATOR No.2
2.GS

1.φZ 3.X1 3.X1

BLK No.1 1 TRANS
2.φZE 4.X2 4.X2
CIRCUIT
(W017)

BLU J1109 H-7LPRD 0122

3.φ A J1110 J1191 5.TI 5.TI
IL -G -12P

WHT IL-G-8P 3 5
IL-G -11P CPA-264
J1111

4.φB 6.TIE

8W
IL-4P 6.TIE BRAKE CIRCUIT A
RED C202 S.G.
5.+12V 7.+15V J2103 (W104)

P2103
7.+15V 0.22UF 200V CFA-259
B.6 Interconnection Diagram of Scanner Unit

SHIELD ZCRD1256※
8.GND 350209-2 CFR-229

ZCRD1257※
6.GND 8.GND 120Ω
9.NC 9.NC J2101 1.X1 MAG FILTER 30W
×4
1586514-2 BRAKE CIRCUIT B
J1 IL-G -6P 10.NC

(W105)
10.NC 2.X2 CIRCUIT R1 CFA-260

1.MH

3.MN
MODULATOR UNIT

2.7KΩ
2.NC

0.22UF
1.TIY 11.NC

1/2W
R202
(W004) 220pF ×5

C 203
330Ω

200V
INTERCONNECTION R2
2.TIYE 12.NC ZCRD1253※ 30W ×1
(W207)
3.BP
ZCRD1263※ CMB-404 S.G. S.G. R3 R1
4.BPE P1118 P2101 (W310) (W309)
B3P-SHF

BLU 1 1 BL U

1 2 3

1 2 3
5.BZ

BLK.T
1.HMC NT ZC RD1539※ R4 ZCRD1538※
J1118

(W308)

P1303
J1303
2 WHT (W201)

BLK.T
WHT 2

W101
6.BZE 2.+15V (W107) ZC RD1537※ P1921 P1911
BLK 3 3 BLK ZCRD1259※ ZCRD1260※
3.GND W 101 P1941 J1941 J1921 J1911
J2 IL-G -4P 1.+12V 1-350209-0

1.BKH1

3.BKH1

1.BKS1
2.BKS2
1-350210-0
P1002 to TB102

B －22
2.NC

2.NC
1.VD
2.VDE
T/R CONTROL CIRCUIT P1103 P1003 3.+12VE
1.+15V 1.+15V
CMC-1205R

1.MH

3.MN
2.NC
3.MTR+ 2.+12V 4 4 2.+12V S3B-XH-A
5 5 BRAKE CONTROL CIRCUIT

B8P-SHF
4.MTR- 3.G ND 3.+8V

B8P-SHF
J1003
J1002

J1103
4.GND 6 6 4.GND
TB101 MSTBA2.5/11-G 5.-15V 7 7 5.-15V
1586514-2 (W305) CCB-655
8 8 Z CRD1454※ J1912 P1912
1.BP+ 6.10V 6.X1
B2PS-VH
2.BP- 7.10VE 9 9 7.X2 J1001

1.VERR
3.BZ+ 10 10 POWER SUPPLY 350428-1
1.VERR1 1.VERR1

2.NC
DISPLAY UNIT

8.+5V 8.+5V 2.E 2.E

3.N
1.P

2.E
CIRCUIT

J1301

P1301
IL-3P 1-480700-0
4.BZ- 1.M+ BLU IL-2P
1.MC T P1104 P1004 1.HMCNT J1212 P1212 J1903 IL-2P
5.TRIG+ 1.MC T 2.M- J1905
CBD-1682A WHT 2.+15V RELAY FILTER

B6P-SHF
2.MBK P1903

B9P-SHF
2.MBK J1202 P1202 (W307) P1905
NKE-1125 (AC110V)

J1004
6.TRIG- BLK

J1104
1 1

RED

BLK
3.TISTOP 3.HSP 3.G ND CIRCUIT 1.MU2 (W303) ZCRD1536※
7.MTR+

P1211
2 2 P1505 (W304)
8.MTR- 4.G ND 4.HTER CSC-656 2.GND ZCRD1452※

J1211
3 3 ZCRD1314※
9.MTRE 5.MPS 5.TISTOP PC1201 3.MV2 J1505

2.N
1.P
4 4 B2P-VH
6.MIER J4 J5 J3

1.VERR
6.C 2 B3P-NV

2.NC

4.NC
10.VD+

1.U1

3.V1
1.MU2 B3P-VH
11.VD- 7.G ND 350209-1 350209-1 B02P-NV(LF)(SN ） J1201 1.R1
J1112 J1113 J1114 2.NC

2.E
2.1A
1.2A

2.1A
1.2A

2.1A
1.2A
8.MPS B4P-VH
>

B6P-VH
50/60ｋW IL-G-9P IL-G-3P IL-G-3P 3.MV2 2.NC
P1201

8.STABY_REQ
J8 9.MIER 4.N C PC 1501 3.R2
J1106 J1105

3.FAN _ERR 2
3.FAN_ERR1
2.HVGATE1
B.DRAWINGS

R2

3.TISTOP1
5.N C

J1504
P1504
IL-8P IL-G-5P IL-G-2P B201 H-7EPRD0035
5 5

1.HTER1
(W206) P3 6.G ND

1.+12V

1 0 P1
1 0J5 1
R1

1.+12V
2.GND
4.+24V

7.+15V

1.+12V

J1503
4.PMS
5.GND

5.GND

4.GND

2.GND
1.PW1
2.PW2
3.PW3

5.CNT
2.PTE

7.TXE

2.NC

4.NC
3.LVR

2.S2
3.S3

5.S5
6.S6

1.M1

3.M2

5.M3
6 6

1.S1

4.S4
6.+5V
ZC RD 1262※
1.PTI

6.TXI

J 1502
8.NC

9.NC

2.C 2

5
RED.T

BLK.T
(W203) (W302) 1.2kΩ
ZCRD1261※ ZC RD1265※ 30W ×2
P1113 P1114 P1502

7
to CCB-655 J1941

ｱｶ
ｼﾛ
P1105

1
S-32F
S101
7 7 WHT
RED
AC100V BRAKE CIRCUIT
8 8

YEL
RED
BLU
(W308) MOTOR DRIVER CFA-253
(W301) P1503 WC1

8
2
J1302

P1302
ZC RD 1537※
(W018) (W006)
ZCRD1264※ CBD-2001
>

MOTOR

RED

YEL
BLU
ZCRD1277※ B201 FAN ZCRD1254※

BLK.T
RED.T
CBP-203
JMA-9100 Instruction Manual

B 101
H-7BFRD0002 W401 7ZCRD1508※

+48VG
H-7BDRD0050 MOTOR

+48V

+12V
FAN SAFETY SWITCH

V1

W1
B202

U1

WHT.T
HEATER

2.PMS
2.PTE

4.TXE

1.LVR
1.PTI

3.TXI
CSD-654
TB102 CONTROL PART TH101

3.E
H-7BF RD0002

P82 J 82
P81 J81

+48VG
+48V
CHG-216

U1

V1

W1
TR101 WHT.T
（OPTION） （100W） U V UTH

WHT
BRN
WHT
BLK

RED
BLU

BLK
TB105 U V UTH
SCANNER UNIT INTERCONNECTION DISPLAY UNIT
ZCRD1280※
S.G. NKE-1125PM (AC100V) X25kW,2ﾕﾆｯﾄ
CAX-11
B.6.3 空中線機内接続図
PM
NJU-85
 B
A103 ANTENNA
NJC4002
RECEIVER UNIT NRG-162A DUMMY FILTER
B.6 Interconnection Diagram of Scanner Unit

A301 Ａ104
NJS6930 NJC9952
RECEIVER CIRCUIT CMA-866A
J101 ③ ③
BM15B-XASS-TE S.G.
12.VD_DC

D.L
10.TGTE

② ① ① ② MAG
14.VDE
13.TNL
6.-15V
7.+15V

11.TNI
4.TNC

8.GND

Ｖ101
9.TGT

15.VD
1.BS3
2.BS2
3.BS1

5.+5V

M1568BS
Ａ101 Ａ102
NJC3901M NJ C3901M
P3001
CHT-71A

GRN

YEL
(W001)
B102 Z CRD1251※

Fig B-20: Interconnection Diagram of NKE-1125 (AC220V)

MODULATOR UNIT NMA-550 (W106)
ZC RD1258※

150Ω MD-12N1 MD-12N1

SE C201
(W003)

R201 CD202 CD201

P1109 P1110 ZCRD1252※ J2102 0.01UF 1KV
IL-10P
P1111 P2102 (W103) 4 6
J13 1.SHORT 1.SHORT ZCRD1255※ T1
5.MicPS
6.VDINE

P13 IL-6P
11.TRG2
ENCODER

5.TGTE
7.VDIN

1.MONI

2.MAG I
4.TNC

10.GND
7.-15V

9.+15V

2.MAGI PULSE
1.BS3
2.BS2
3.BS1

1.RXD
2.TXD

4.GND
8.+5V

4.TGT
3.GSE

6.TNL

YEL
3.+5V
8.TNI

2
MODULATOR No.2
2.GS

1.φZ 3.X1 3.X1

BLK No.1 1 TRANS
2.φZE 4.X2 4.X2
CIRCUIT
(W017)

BLU J1109 H-7LPRD 0122

3.φ A J1110 J1191 5.TI 5.TI
IL -G -12P

WHT IL-G-8P 3 5
IL-G -11P CPA-264
J1111

4.φB 6.TIE

8W
IL-4P 6.TIE BRAKE CIRCUIT A
RED C202 S.G.
5.+12V 7.+15V J2103 (W104)

P2103
SHIELD 7.+15V
ZCRD1256※ 0.22UF 200V CFA-259
8.GND 350209-2 CFR-229

ZCRD1257※
6.GND 8.GND 120Ω
9.NC 9.NC J2101 1.X1 MAG FILTER 30W
×4
1586514-2 BRAKE CIRCUIT B
J1 IL-G -6P 10.NC

(W105)
10.NC 2.X2 CIRCUIT R1 CFA-260

1.MH

3.MN
MODULATOR UNIT

2.7KΩ
2.NC

0.22UF
1.TIY 11.NC

1/2W
R202
(W004) 220pF ×5

C 203
>

330Ω

200V
INTERCONNECTION R2
2.TIYE 12.NC ZCRD1253※ 30W ×1
(W207)
3.BP CMB-404
B.DRAWINGS

S.G. S.G. R3 R1
ZCRD1263※
4.BPE P1118 P2101 (W310) (W309)
B3P-SHF

BLU 1 1 BL U

1 2 3

1 2 3
5.BZ

BLK.T
1.HMC NT ZC RD1539※ R4 ZCRD1538※
J1118

(W308)

P1303
J1303
2 WHT (W201)

BLK.T
WHT 2

W101
6.BZE 2.+15V (W107) ZC RD1537※ P1921 P1911
BLK 3 3 BLK ZCRD1259※ ZCRD1260※
3.GND W 101 P1941 J1941 J1921 J1911
J2 IL-G -4P 1.+12V 1-350209-0

1.BKH1

3.BKH2

1.BKS1
2.BKS2
1-350210-0
P1002 to TB102

B －23
1.VD 2.NC
T/R CONTROL CIRCUIT

2.NC
P1103 P1003 3.+12VE
2.VDE 1.+15V 1.+15V
CMC-1205R

1.MH

3.MN
2.NC
3.MTR+ 2.+12V 4 4 2.+12V S3B-XH -A
5 5 BRAKE CONTROL CIRCUIT

B8P-SHF
4.MTR- 3.G ND 3.+8V

B8P-SHF
J1003
J1002

J1103
>

4.GND 6 6 4.GND
TB101 MSTBA2.5/11-G 5.-15V 7 7 5.-15V
1586514-2 (W305) CCB-655
JMA-9100 Instruction Manual

8 8 Z CRD1454※ J1912 P1912

1.BP+ 6.10V 6.X1
B2PS-VH
2.BP- 7.10VE 9 9 7.X2 J1001

1.VERR
3.BZ+ 10 10 POWER SUPPLY 350428-1
1.VERR1 1.VERR1

2.NC
DISPLAY UNIT

8.+5V 8.+5V 2.E 2.E

3.N
1.P

2.E
CIRCUIT

J1301

P1301
IL-3P 1-480700-0
4.BZ- 1.M+ BLU IL-2P
1.MC T P1104 P1004 1.HMCNT J1212 P1212 J1903 IL-2P
5.TRIG+ 1.MC T 2.M- J1905
CBD-1682A WHT 2.+15V RELAY FILTER

B6P-SHF
2.MBK P1903
NKE-1125 (AC220V)

B9P-SHF
2.MBK J1202 P1202 (W307) P1905

J1004
6.TRIG- BLK

J1104
1 1

RED

BLK
3.TISTOP 3.HSP 3.G ND CIRCUIT 1.MU2 (W303) ZCRD1536※
7.MTR+

P1211
2 2 P1505 (W304)
8.MTR- 4.G ND 4.HTER CSC-656 2.GND ZCRD1452※

J1211
3 3 ZCRD1314※
9.MTRE 5.MPS 5.TISTOP PC1201 3.MV2 J1505

2.N
1.P
4 4 B2P-VH
6.MIER J4 J5 J3

1.VERR
6.C 2 B3P-NV

2.NC

4.NC
10.VD+

1.U1

3.V1
1.MU2 B3P-VH
11.VD- 7.G ND 350209-1 350209-1 B02P-NV(LF)(SN ） J1201 1.R1
J1112 J1113 J1114 2.NC

2.E
2.1A
1.2A

2.1A
1.2A

2.1A
1.2A
8.MPS B4P-VH

B6P-VH
50/60ｋW IL-G-9P IL-G-3P IL-G-3P 3.MV2 2.NC
P1201

8.STABY_REQ
J8 9.MIER 4.N C PC 1501 3.R2
J1106 J1105

3.FAN _ERR 2
3.FAN_ERR1
2.HVGATE1
R2

3.TISTOP1
5.N C

J1504
P1504
IL-8P IL-G-5P IL-G-2P B201 H-7EPRD0034
5 5

1.HTER1
(W206) P3 6.G ND

1.+12V

1 0 P1
1 0J5 1
R1

1.+12V
2.GND
4.+24V

7.+15V

1.+12V

J1503
4.PMS
5.GND

5.GND

4.GND

2.GND
1.PW1
2.PW2
3.PW3

5.CNT
2.PTE

7.TXE

2.NC

4.NC
3.LVR

2.S2
3.S3

5.S5
6.S6

1.M1

3.M2

5.M3
6 6

1.S1

4.S4
6.+5V
ZC RD 1262※
1.PTI

6.TXI

J 1502
8.NC

9.NC

2.C 2

5
RED.T

BLK.T
(W203) (W302) 1.2kΩ
ZCRD1261※ ZC RD1265※ 30W ×2
P1113 P1114 P1502

7
to CCB-655 J1941

ｱｶ
ｼﾛ
P1105

1
S-32F
S101
7 7 WHT
RED AC220V BRAKE CIRCUIT
8 8

YEL
RED
BLU
(W308) CFA-253
(W301) MOTOR DRIVER P1503 WC1

8
2
J1302

P1302
ZC RD 1537※
(W018) (W006)
ZCRD1264※ CBD-2000
MOTOR

RED

YEL
BLU
ZCRD1277※ B201 FAN ZCRD1254※

BLK.T
RED.T
CBP-203 B 101
H-7BFRD0002 W401 7ZCRD1508※

+48VG
H-7BDRD0050 MOTOR

+48V

+12V
FAN SAFETY SWITCH

V1

W1
B202

U1

WHT.T
HEATER

2.PMS
2.PTE

4.TXE

1.LVR
1.PTI

3.TXI
CSD-654
TB102 CONTROL PART TH101

3.E
H-7BF RD0002

P82 J 82
P81 J81

+48VG
+48V
CHG-216

U1

V1

W1
TR101 WHT.T
（OPTION） （100W） U V UTH

WHT
BRN
WHT
BLK

RED
BLU

BLK
TB105 U V UTH
SCANNER UNIT INTERCONNECTION DISPLAY UNIT
ZCRD1280※
S.G. NKE-1125PM (AC220V) X25kW,2ﾕﾆｯﾄ
CAX-11
B.6.4 空中線機内接続図
PM
NJU-85
 HEATER CONTROL PART
CHG-216
(OPTION)

（100W）
TR101

WHT.T TH101
WHT.T
TB105
U BRAKE CIRCUIT A

Fig B-21: Interconnection Diagram of NKE-1129 (AC110V)

AC100V

W401 7Z CRD1508※ CFA-259

SAFETY SWITCH CSD-655 V 120Ω
×4
（W301) ZCRD1285※ 30W BRAKE CIRCUIT B
UTH R1 CFA-260
S101 WHT.T 330Ω
R2
S-32 30W ×1
RED 2 1
R3 R1 (W309)
(W310) ZCRD1538※
ZCRD1539※ R4
RED.T 5 4 RED.T (W308)
ZCRD1548※ P1921 P1911
BLK.T 8 7 BLK.T （W302) ZCRD1286※ P1941 J 1941
B.6 Interconnection Diagram of Scanner Unit

TB103 J1921 J 1911

1-350209-0

1.BKH1

3.BKH2

1.BKS1
2.BKS2
1.+12V 1-350210-0
2.NC
U1

2.NC
WHT 3.+12VE
V1 S3B-XH-A
BRAKE CONTROL CIRCUIT
TRANSCEIVER UNIT

W1
CCB-655
+12V
C2 C101 + C102

1.VERR
B102 1000μ 2200p

2.NC
RED 1.VERR1
ΦZE

2.E
3.N
1.P
16V 50V 2.E
YEL
ΦZ J1912 J1903 IL-2P J 1905

B －24
SE P1903
P1912 P1905

1.RED

3.BLK
BLU
ΦA S.G. S.G.
（W305)
SHIELD (W307)
E ZCRD1455※ ZCRD1547※
WHT
ΦB ENCORDER CHT-71A1
BLK BLK
J 1505

1.P

2.N
B2P-VH

1.VERR
S.G .
1.MU2 B3P-VH
（W303) ZCRD1278※

2.E
TB104 J81 P81 2.NC
NKE-1129 (AC110V)

1.R1

B6P-VH
1 3.MV2 PC1501 2.NC R2 R1
PTI WHT 4.NC B201 H-7EPRD 0035 3.R2 1.2kΩ 1.2kΩ
TRANSCEIVER UNIT TRANSCEIVER UNIT

BLK 5.NC 30W 30W

PTE

J1504
P1504
WHT 6.GND

1 0 J1
(W304)

1 0P1

J1503
BRN

5.M3
2.NC

4.NC
LVR

2.S2
3.S3

5.S5
6.S6

1.M1

3.M2
1.S1

4.S4
ZCRD1314※

J1502
5
>

PMS J82 P82

CFA-253
BLU 1 BLU BRAKE CIRCUIT
E P1502
B.DRAWINGS

RED RED
TXI BLK BLK

ZCRD1280※
P1503 WC1
TXE AC100V
MOTOR MOTOR DRIVER
CBD-2001
CBP-203 B101
VERR1 H-7B DRD0050 MOTOR
E S.G.
>
JMA-9100 Instruction Manual

PM NJU-85
SCANNER UNIT INTERCONNECTION
CAX-12
NKE-1129PM (AC100V) Xﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
空中線機内接続図
B.6.5
 B
B.6 Interconnection Diagram of Scanner Unit

HEATER CONTROL PART

CHG-216
(OPTION)

（100W）
TR101

WHT.T TH101
WHT.T
TB105
U BRAKE CIRCUIT A

Fig B-22: Interconnection Diagram of NKE-1129 (AC220V)

AC100V

W401 7Z CRD1508※ CFA-259

SAFETY SWITCH CSD-655 V 120Ω
×4
（W301) ZCRD1285※ 30W BRAKE CIRCUIT B
UTH R1 CFA-260
S101 WHT.T 330Ω
R2
S-32 30W ×1
RED 2 1
R3 R1 (W309)
(W310) ZCRD1538※
ZCRD1539※ R4
RED.T 5 4 RED.T (W308)
ZCRD1548※ P1921 P1911
TB103 BLK.T 8 7 BLK.T （W302) ZCRD1286※ P1941 J 1941 J1921 J 1911
1-350209-0

1.BKH1

3.BKH2

1.BKS1
2.BKS2
1.+12V 1-350210-0

2.NC
2.NC
U1 WHT 3.+12VE
V1 S3B-XH-A
>

BRAKE CONTROL CIRCUIT

TRANSCEIVER UNIT

W1
B.DRAWINGS

CCB-655
+12V
C2 C101 + C102

1.VERR
B102 1000μ 2200p

2.NC
RED 1.VERR1
ΦZE

2.E
3.N
1.P
16V 50V 2.E
YEL
ΦZ J1912 J1903 IL-2P J 1905

B －25
SE P1903
P1912 P1905

1.RED

3.BLK
BLU
ΦA S.G. S.G.
（W305)
SHIELD (W307)
E ZCRD1455※ ZCRD1547※
>

WHT
ΦB ENCORDER CHT-71A1
JMA-9100 Instruction Manual

BLK BLK
J 1505

1.P

2.N
B2P-VH

1.VERR
S.G .
1.MU2 B3P-VH
（W303) ZCRD1278※

2.E
TB104 J81 P81 2.NC
NKE-1129 (AC220V)

1.R1

B6P-VH
1 3.MV2 PC1501 2.NC R2 R1
PTI WHT 4.NC B201 H-7EPRD 0034 3.R2 1.2kΩ 1.2kΩ
TRANSCEIVER UNIT TRANSCEIVER UNIT

BLK 5.NC 30W 30W

PTE

J1504
P1504
WHT 6.GND

1 0 J1
(W304)

1 0P1

J1503
BRN

5.M3
2.NC

4.NC
LVR

2.S2
3.S3

5.S5
6.S6

1.M1

3.M2
1.S1

4.S4
ZCRD1314※

J1502
5
PMS J82 P82
CFA-253
BLU 1 BLU BRAKE CIRCUIT
E RED RED
P1502
TXI BLK BLK

ZCRD1280※
P1503 WC1
TXE AC220V
MOTOR MOTOR DRIVER
CBD-2000
CBP-203 B101
VERR1 H-7B DRD0050 MOTOR
E S.G.
PM NJU-85
SCANNER UNIT INTERCONNECTION
CAX-12
NKE-1129PM (AC220V) Xﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
空中線機内接続図
B.6.6
 A103 ANTENNA
NJC4002
RECEIVER UNIT NRG-162A DUMMY FILTER Ａ104
Ａ302 Ａ301
NJS6926 NJS6930 NJC9952
RECEIVER CIRCUIT
J101 CMA-866A ③ ③
BM15B-XASS-TE S.G.
12.VD_DC

PIN

D.L
10.TGTE

② ① ① ② MAG
14.VDE
13.TNL
6.-15V
7.+15V

11.TNI
4.TNC

8.GND
9.TGT

15.VD
1.BS3
2.BS2
3.BS1

5.+5V

Ｖ101
M1568BS
Ａ101 Ａ102
NJC 3901M NJC 3901M
P3001

ﾐﾄﾞﾘ

ｷ
(W001)
ZCRD1233※
MODULATOR UNIT (W106)

MD-12N1 MD-12N1
ZC RD1245※
NMA-552

CD201
(W003) C201

Fig B-23: Interconnection Diagram of NTG-3225

P1109 P1110 ZC RD 1234※ J2102 0.01UF 1KV
IL-10P
P1111 P2102 (W103) 4 6
1.SHORT 1.SHORT ZCRD1242※
T1
11.TRG2
5.MicPS
6.VDINE

5.TGTE
1.MONI

10.GND

2.MAGI 2.MAG I
7.VDIN

7.-15V

9.+15V
4.TNC

CD202
1.RXD
2.TXD

4.GND
4.TGT
3.GSE

6.TNL
1.BS3
2.BS2
3.BS1

8.+5V

3.+5V
8.TNI

No.2 2 PULSE TRANS

2.GS

3.X1
3.X1
4.X2 4.X2
MODULATOR No.1 1 H-7LPRD0122
J1 J1109 J1110 J1191 5.TI 5.TI CIRCUIT
IL -G-12P

IL-G-6P 3 5
B.6 Interconnection Diagram of Scanner Unit

IL-G-8P
CPA-264

R201
IL-G -11P
J1111

150Ω
IL-4P 6.TIE 6.TIE S.G.
1.TIY C 202
J2103 (W104)

8W
7.+15V

P2103
7.+15V 0.22UF 200V
2.TIYE 8.G ND 350209-2 ZCRD1243※ CFR-229
3.BP 8.GND
J2101 MAG FILTER

ZCRD1244※
9.NC 9.NC 1.X1
4.BPE 10.NC 1586514-2 2.X2 CIRCUIT

(W105)
5.BZ 10.NC

1.MH

3.MN

2.7KΩ
2.NC
MODULATOR UNIT

0.22UF
11.NC

R202
220pF×5

1/2W
6.BZE

C 203
200V
12.NC INTERCONNECTION
J2 IL-G-4P CMB-405 S.G. S.G.
P2101
B3P-SHF
1.VD 1.HMCNT P1118 (W004)
J1118

BLK.T
2.VDE ZC RD 1235※ W201
2.+15V ZCRD1246※
3.MTR+

B －26
3.GND (W005)
4.MTR- S.G.
ZCRD1236※
P1002
T/R CONTROL CIRCUIT P1103 P1003
1.+15V 1.+15V (W301)
CMC-1205R

1.MH

3.MN
2.NC
2.+12V 2.+12V J1001 P1202 ZC RD 1248※
TB101

B8P-SHF
MSTBA2.5/11-G 3.G ND 3.+8V 350428-1

B8P-SHF
P101

J1003
J 1202

P1212
J1103
1.BP+ 4.GND 4.GND J1002 1.M+ IL-3P B3P-NV

2.GND
J1212

1.MU2

3.MV2
2.BP- 5.-15V 5.-15V 1586514-2 2.M- 1.HMCNT 1.VERR
3.BZ + 6.10V 6.10V 2.+15V
2.E
4.BZ - 7.10VE 7.10VE 3.GND
POWER SUPPLY CIRCUIT RE LAY FILTER CIRCUIT

P1211

IL-2P
5.TRIG + 8.+5V 8.+5V

J 1211
CBD-1682A CSC-656

IL-3P
6.TRIG - P1104 P1004 (W303) ZCRD1483※
7.MTR+ 1.MCT 1.MCT PC1201

2.NC

4.NC
B6P-SHF

1.U1

3.V1
2.MBK

B9P-SHF
2.MBK

J1004
8.MTR-

J1104
3.TISTOP 3.HSP J1201
9.MTRE B4P-VH
10.VD+ 4.GND 4.HTER
5.MPS 5.TISTOP P1201
11.VD- (W302)
6.MIER 6.C2 J4 J5 J3
>

(W006) 350209-1 350209-1 B02P-NV(LF)(SN） ZCRD1249※

J1112 J1113 J1114 J13 ZCRD1237※
7.G ND

2.1A
1.2A

2.1A
1.2A

2.1A
1.2A
IL-6P 8.MPS
B.DRAWINGS

50/60ｋW IL-G-9P IL-G-3P IL-G -3P

J8 1.φ Z 9.MIER

8.STABY_REQ

RED

BLK
J1106

RED

BLK
J1105

3.FAN_ERR2
3.FAN _ERR1
2.φ ZE

2.HVGATE1
I L-8P IL-G -5P

3.TISTOP1
IL-G-2P
3.φA TB202

1.HTER1
P3

1.+12V
4.+24V

1.+12V

1.+12V
2.GND
7.+15V
4.PMS
5.GND
2.PTE

7.TXE

5.GND

4.GND

2.GND
4.φ B
3.LVR

1.PW1
2.PW2
3.PW3

5.CNT

U0

V0
WHT.T +48VG
6.+5V

U1

V1
1.PTI

6.TXI

8.NC

9.NC

2.C 2

RED.T +48V
5.+12V
NTG-3225

6.G ND (W007) ZCRD1238※

(W014) HC3L2

WHT
RED
P1105

V1
P8

U1

V0
U0
ZCRD1241※
(W013) ZCRD1240※ (W008) ZC RD1239※
>

(W203) ZCRD1247※
3L2 3L1 3L1
ANTENNA DISPLAY
JMA-9100 Instruction Manual

TB201 TB204 TB203 UNIT

TRIG-

MTRE
MTR+
MTR-
TRIG+

BP -/ BZ-

+48VG
VERR

+12V
PMS
PTE

TXE

φZE

+48V
LVR
VD+
VD-

BP+

PTI

TXI
BZ+

φB
φA
φZ
C2
E
E

E
DISPLAY UNIT ANTENNA ANTENNA DISPLAY UNIT
TRANSCEIVER UNIT INTERCONNECTION
CMK-593
H-7ZCRD####*:
“#” means specification document No.
B.6.7 “*” means revision of the specfication document. NTG-3225
送受信機機内接続図
 B
ANTTENA
RECEIVER UNIT NRG-229 Ａ102
B.6 Interconnection Diagram of Scanner Unit

Ａ301 FILTER DUMMY H-7ANRD0018

NJS6318
IF CIRCUIT CAE-499 ① ①
S.G.
D.L

J101 J102 ② ③ ③ ② MAG Ｖ101

IL-9P IL-7P M1555
2.TGTE

4.-15V

6.+15V
5.MPS
4.TNC

7.GND
1.TGT
6.VDE

3.TNL
1.BS3
2.BS2
3.BS1

8.+5V

5.TNI
9.NC
7.VD

RF CIRCUIT Ａ101

GRN
CHT-71A

YEL
NJC3316
CAF-595
B102 R ECEIRVER UNIT
P3001 P3002
MODULATOR UNIT (W106)

Fig B-24: Interconnection Diagram of NKE-1130 (AC110V)

INTERCONN ECTION
Z CRD1321※
CMA-902 NMA-551

MD-12N1 MD-12N1
SE (W001) (W002)
ZCRD1266※

CD 201
ZCRD1267※
P1109 P1110 (W003) C 201
J13 ZC RD 1268※ J2102 0.01UF 1KV
P13 IL-10P (W103)
IL-6P P1111 P2102 4 6
ENCODER

11.TRG2
5.MicPS
6.VDINE

5.TGTE
1.MONI

10.GND

YEL 1.SHORT
1.SHORT T201
7.VDIN

7.-15V

9.+15V
4.TNC

1.RXD
2.TXD

4.GND
4.TGT
3.GSE

6.TNL

ZCRD1318※
1.BS3
2.BS2
3.BS1

8.+5V

CD202
1.φZ
3.+5V
8.TNI
2.GS

BLK 2.MAGI 2.MAG I

2.φZE
MODULATOR No.2 2 PULSE
(W017)

BLU 3.X1 3.X1

3.φ A J1109 J1110 No.1 1 TRANS
WHT
4.φB
J1191 4.X2 4.X2
CIRCUIT H-7LPRD0122
IL -G -8P IL-G-11P IL-4P 5.TI

150Ω
RED 5.TI
IL-G-12P

R２01
3 5 S.G.
5.+12V CPA-264 BRAKE CIRCUIT A
J1111

6.TIE

ZCRD 1320※ 8W
SHIELD 6.TIE
6.GND (W104) C202 CFR-229 CFA-261
7.+15V J2103

P2103
7.+15V 0.22UF 200V
8.G ND 8.GND 350209-2 ZCRD 1319※ MAG FILTER 120Ω
J2101 30W ×4

(W105)
J1 IL-G-6P 9.NC 9.NC 1.X1 CIRCUIT BLAKE CIRCUIT B
1.TIY 10.NC 10.NC 1586514-2 2.X2 220pF ×5 R1 CFA-262
>

1.MH

3.MN

2.7KΩ
2.NC
11.NC MODULATOR UNIT

0.22UF
2.TIYE

R202
330 Ω

1/2W
R2

C 203
3 0W ×1

200V
3.BP 12.NC INTERCONNECTION
B.DRAWINGS

4.BPE CMB-406 S.G. S.G.

R3 R1 (W309)
5.BZ (W310) ZCRD1543※
P2101
B3P-SHF

6.BZE 1.HMCNT P1118 （W004） ZCRD1544※ R4

J1118

BLK.T
ZCRD1269※ （W201) (W308)
2.+15V ZCRD1273※ P1921 P1911
ZC RD1542※
J2 IL-G-4P 3.G ND (W005)
P1941 J1941 J1921 J1911

B －27
1-350209-0

1.BKH1

3.BKH2

1.BKS1
2.BKS2
1.VD Z CRD1270※ 1.+15V 1-350210-0
P1002 to CMC-1205R J1112 2.NC

2.NC
2.VDE T/R CONTROL CIRCUIT P1103 P1003 3.+15VE
3.MTR+ 1.+15V 1.+15V
CMC-1205R J1001

1.MH

3.MN
2.NC
2.+12V 2.+12V S3B-XH-A
4.MTR- 350428-1
>

(W305) BRAKE CONTROL CIRCUIT

B8P-SHF
3.G ND 3.+8V

B8P-SHF
J1003
ZC RD 1456※

J1103
4.G ND 4.GND J1002 1.M+
CCB-655
JMA-9100 Instruction Manual

TB101 MSTBA2.5/11-G
5.-15V 5.-15V 1586514-2 2.M-
1.BP+ IL-2P
6.10V 6.10V 1.VERR1 1.VERR1
2.BP-

1.VERR
7.10VE 7.10VE 2.E 2.E
3.BZ + POWER SUPPLY

2.NC
8.+5V 8.+5V J1912
DISPLAY UNIT

3.N
1.P

2.E
IL-3P P1212 J1212
4.BZ -
5.TRIG + P1104 P1004 CIRCUIT BLU
1.HMCNT RELAY FILTER
P1912 1-480700-0
J1903 IL-2P
1.MCT 1.MCT J1905
NKE-1130 (AC110V)

WHT CIRCUIT B3P-NV

CBD-1682A 2.+15V P1903

B6P-SHF
6.TRIG - 2.MBK (W307) P1905

B9P-SHF
2.MBK J1202 P1202

J1004
BLK

3.BLK
J1104

1.RED
7.MTR+ 3.TISTOP 3.HSP 3.GND CSC-656 (W311) ZCRD1541※ (W304)
1.MU2

P1211
ZCRD1545※ P1505 ZCRD1316※
8.MTR- 4.GND PC1201 2.G ND J1511

J1211
4.HTER

IL-3P
P1511 1. P J 1505 B3P-VH
9.MTRE 5.MPS 5.TISTOP 3.MV2 B2P-VH 1.R1
J3 2. N

1.VERR
10.VD+ J4 J5

2.NC

4.NC
6.MIE R 6.C2

1.U1

3.V1
11.VD- 350209-1 350209-1 B02P-NV(LF)(SN） 2.NC
7.GND J1201

2.E
J1112 J1113 J1114 1.MU2 3.R2
(W006) B4P-VH

2.1A
1.2A

2.1A
1.2A

2.1A
1.2A
50/60ｋW IL-G-9P IL -G-3P IL-G -3P 8.MPS 2.NC

J1504
ZCRD1271※

P1504
P1201 PC 1501
J8 9.MIER SAFETY SWITCH R2

8.STABY_REQ

B6P-VH
J1106 J1105 3.MV2

3.FAN_ERR2
B201 H-7EPRD0035

3.FAN_ERR1
2.HVGATE1
I L-8P IL-G -5P 4.NC

3.TISTOP1
IL-G-2P R1
CSD-656

1.HTER1
P3 5.NC 1.2kΩ

1.+12V
2.GND
4.+24V

7.+15V

1.+12V

1.+12V
4.PMS

5.GND

2.GND
2.PTE

7.TXE
5.GND

4.GND
3.LVR

1.PW1
2.PW2
3.PW3

5.CNT
6.G ND 30W

6.+5V
1.PTI

6.TXI

(W203)
8.NC

1 0P1
1 0 J1
BLK.T
9.NC

2.C2

RED .T
ZCRD1274※ (W302)

5
5

J1503
CFA-255

2.NC

4.NC
1.M1

3.M2

5.M3
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
Z CRD1453※

J1502
(W303) BRAKE CIRCUIT
(W008)

9
P1114

3
P1113 P1105 ZC RD1284※

S-32F
S101
WHT ZCRD1283※

RED

RED
YEL

YEL
BLU

BLU
to CCB-655 J1941 RED P1502
(W301)

8
2
(W018) B104 FAN ZCRD1322※
P1503
WC1 AC100V

BLK.T
ZCRD1275※ (W308) MOTOR DRIVER
(W010)

RED.T
ZCRD1542※ ZCRD1272※ CBD-2001
J 1112 TB102 MOTOR
W401 7ZCRD1509
P1112

+48VG
CBP-205

+48V
B101

UTH
U1

V1

W1

V
1

4
2.PMS
2.PTE

4.TXE

1.LVR
HEATER CONTROL PART
1.PTI

3.TXI
WHT.T H-7BD RD0049 MOTOR

3.E
FAN

HT1 0 1
B103

P82 J 82
CHG-215
P81 J81

+48VG

UTH
+48V

V1
U1

W1

V
U
2

4
1
WHT.T TR101 (OPTION)
（200W）

WHT
BRN
BLK

RED
BLU
WHT

BLK
SCANNER INTERCONNECTION
CAX-13 DISPLAY UNIT
NKE-1130PM （AC100V) S30kw, 2ﾕﾆｯﾄ
B.6.8 7ZCRD1279※
S.G.
空中線機内接続図
PM
NJU-84
 ANTTENA
RECEIVER UNIT NRG-229 Ａ102
Ａ301 FILTER DUMMY H-7ANRD0018
NJS6318
IF CIRCUIT CAE-499 ① ①
S.G.
D.L

J101 J102 ② ③ ③ ② MAG Ｖ101

IL-9P IL-7P M1555
2.TGTE

4.-15V

6.+15V
5.MPS
4.TNC

7.GND
1.TGT
6.VDE

3.TNL
1.BS3
2.BS2
3.BS1

8.+5V

5.TNI
9.NC
7.VD

RF CIRCUIT Ａ101

GRN
CHT-71A

YEL
NJC3316
CAF-595
B102 R ECEIRVER UNIT
P3001 P3002

Fig B-25: Interconnection Diagram of NKE-1130 (AC220V)

INTERCONN ECTION MODULATOR UNIT (W106)
Z CRD1321※
CMA-902 NMA-551

MD-12N1 MD-12N1
SE (W001) (W002)
ZCRD1266※

CD 201
ZCRD1267※
P1109 P1110 (W003) C 201
J13 ZC RD 1268※ J2102 0.01UF 1KV
P13 IL-10P (W103)
IL-6P P1111 P2102 4 6
ENCODER

11.TRG2
5.MicPS
6.VDINE

5.TGTE
1.MONI

10.GND

YEL 1.SHORT
1.SHORT T201
7.VDIN

7.-15V

9.+15V
4.TNC

1.RXD
2.TXD

4.GND
4.TGT
3.GSE

6.TNL

ZCRD1318※
1.BS3
2.BS2
3.BS1

8.+5V

CD202
1.φZ
3.+5V
8.TNI
2.GS

BLK 2.MAGI 2.MAG I

2.φZE
MODULATOR No.2 2 PULSE
(W017)

BLU 3.X1 3.X1

3.φ A J1109 J1110 No.1 1 TRANS
WHT
4.φB
J1191 4.X2 4.X2
CIRCUIT H-7LPRD0122
IL -G -8P IL-G-11P IL-4P 5.TI

150Ω
RED 5.TI
IL-G-12P

R２01
3 5 S.G.
5.+12V CPA-264 BRAKE CIRCUIT A
J1111

6.TIE

ZCRD 1320※ 8W
SHIELD 6.TIE
B.6 Interconnection Diagram of Scanner Unit

6.GND (W104) C202 CFR-229 CFA-261

7.+15V J2103

P2103
7.+15V 0.22UF 200V
8.G ND 8.GND 350209-2 ZCRD 1319※ MAG FILTER 120Ω
J2101 30W ×4

(W105)
J1 IL-G-6P 9.NC 9.NC 1.X1 CIRCUIT BLAKE CIRCUIT B
1.TIY 10.NC 10.NC 1586514-2 2.X2 220pF ×5 R1 CFA-262

1.MH

3.MN

2.7KΩ
2.NC
11.NC MODULATOR UNIT

0.22UF
2.TIYE

R202
330 Ω

1/2W
R2

C 203
3 0W ×1

200V
3.BP 12.NC INTERCONNECTION
4.BPE CMB-406 S.G. S.G.
R3 R1 (W309)
5.BZ (W310) ZCRD1543※
P2101
B3P-SHF

6.BZE 1.HMCNT P1118 （W004） ZCRD1544※ R4

J1118

BLK.T
ZCRD1269※ （W201) (W308)
2.+15V ZCRD1273※ P1921 P1911
ZC RD1542※
J2 IL-G-4P 3.G ND (W005)
P1941 J1941 J1921 J1911

B －28
1-350209-0

1.BKH1

3.BKH2

1.BKS1
2.BKS2
1.VD Z CRD1270※ 1.+15V 1-350210-0
P1002 to CMC-1205R J1112 2.NC

2.NC
2.VDE T/R CONTROL CIRCUIT P1103 P1003 3.+15VE
3.MTR+ 1.+15V 1.+15V
CMC-1205R J1001

1.MH

3.MN
2.NC
2.+12V 2.+12V S3B-XH-A
4.MTR- 350428-1 (W305) BRAKE CONTROL CIRCUIT

B8P-SHF
3.G ND 3.+8V

B8P-SHF
J1003
ZC RD 1456※

J1103
4.G ND 4.GND J1002 1.M+
CCB-655
TB101 MSTBA2.5/11-G
5.-15V 5.-15V 1586514-2 2.M-
1.BP+ IL-2P
6.10V 6.10V 1.VERR1 1.VERR1
2.BP-

1.VERR
7.10VE 7.10VE 2.E 2.E
3.BZ + POWER SUPPLY

2.NC
8.+5V 8.+5V J1912
DISPLAY UNIT

3.N
1.P

2.E
IL-3P P1212 J1212
4.BZ -
5.TRIG + P1104 P1004 CIRCUIT BLU
1.HMCNT RELAY FILTER
P1912 1-480700-0
J1903
NKE-1130 (AC220V)

1.MCT 1.MCT WHT IL-2P J1905

CIRCUIT B3P-NV
CBD-1682A 2.+15V P1903

B6P-SHF
6.TRIG - 2.MBK (W307) P1905

B9P-SHF
2.MBK J1202 P1202

J1004
BLK

3.BLK
J1104

1.RED
7.MTR+ 3.TISTOP 3.HSP 3.GND CSC-656 (W311) ZCRD1541※ (W304)
1.MU2

P1211
ZCRD1545※ P1505 ZCRD1316※
8.MTR- 4.GND PC1201 2.G ND J1511

J1211
4.HTER

IL-3P
P1511 1. P J 1505 B3P-VH
9.MTRE 5.MPS 5.TISTOP 3.MV2 B2P-VH 1.R1
J3 2. N

1.VERR
10.VD+ J4 J5

2.NC

4.NC
6.MIE R 6.C2

1.U1

3.V1
11.VD- 350209-1 350209-1 B02P-NV(LF)(SN） 2.NC
J1201
>

7.GND

2.E
J1112 J1113 J1114 1.MU2 3.R2
(W006) B4P-VH

2.1A
1.2A

2.1A
1.2A

2.1A
1.2A
50/60ｋW IL-G-9P IL -G-3P IL-G -3P 8.MPS 2.NC

J1504
ZCRD1271※

P1504
PC 1501
B.DRAWINGS

J8 9.MIER P1201 R2
SAFETY SWITCH

8.STABY_REQ

B6P-VH
J1106 J1105 3.MV2

3.FAN_ERR2
B201 H-7EPRD0034

3.FAN_ERR1
2.HVGATE1
I L-8P IL-G -5P 4.NC

3.TISTOP1
IL-G-2P R1
CSD-656

1.HTER1
P3 5.NC 1.2kΩ

1.+12V
2.GND
4.+24V

7.+15V

1.+12V

1.+12V
4.PMS

5.GND

2.GND
2.PTE

7.TXE
5.GND

4.GND
3.LVR

1.PW1
2.PW2
3.PW3

5.CNT
6.G ND 30W

6.+5V
1.PTI

6.TXI

(W203)
8.NC

1 0P1
1 0 J1
BLK.T
9.NC

2.C2

RED .T
ZCRD1274※ (W302)

5
5

J1503
CFA-255

2.NC

4.NC
1.M1

3.M2

5.M3
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
Z CRD1453※

J1502
(W303) BRAKE CIRCUIT
(W008)

9
P1113

3
P1114 P1105 ZC RD1284※

S-32F
S101
to CCB-655 J1941 WHT ZCRD1283※

RED

RED
YEL

YEL
BLU

BLU
RED P1502
(W301)

8
2
>

(W018) (W308) B104 FAN ZCRD1322※

P1503
WC1 AC220V

BLK.T
ZCRD1275※ ZCRD1542※ MOTOR DRIVER
JMA-9100 Instruction Manual

(W010)

RED.T
J 1112
ZCRD1272※
TB102 CBD-2000
W401 7ZCRD1509 MOTOR
P1112

+48VG
CBP-205

+48V
B101

UTH
U1

V1

W1

V
1

4
2.PMS
2.PTE

4.TXE

1.LVR
HEATER CONTROL PART
1.PTI

3.TXI
WHT.T H-7BD RD0049 MOTOR

3.E
FAN

HT1 0 1
B103

P82 J 82
CHG-215
P81 J81

+48VG

UTH
+48V

V1
U1

W1

V
U
2

4
1
WHT.T TR101 (OPTION)
（200W）

WHT
BRN
BLK

RED
BLU
WHT

BLK
SCANNER INTERCONNECTION
CAX-13 DISPLAY UNIT
NKE-1130PM （AC220V) S30kw, 2ﾕﾆｯﾄ
B.6.9 7ZCRD1279※
S.G.
空中線機内接続図
PM
NJU-84
 B
SAFETY SWITCH CSD-657
B.6 Interconnection Diagram of Scanner Unit

S101
S-32
（W301) ZCRD1287※ RED 2 3 WHT （W302) ZCRD1288※
RED.T 5 6 RED.T
BLK.T 8 9 BLK.T
BRAKE CIRCUIT A
CFA-261
120Ω
30W
×4
BRAKE CIRCUIT B
R1 CFA-262
R2 330Ω
30W ×1

Fig B-26: Interconnection Diagram of NKE-1139 (AC110V)

R3 R1 (W309)
(W308) (W310) ZCRD1543※
ZCRD1553※ ZCRD1544※ R4
P1921 P1911
P1941 J1941 J1921 J1911
RED 1-350209-0

1.BKH1

1.BKS1
2.BKS2
1.+12V

3.BKH2
1-350210-0
2.NC

2.NC
3.+12VE
S3B-XH-A
BRAKE CONTROL CIRCUIT
CCB-655
TB103
U1

1.VERR
B2PS-VH
W401 7ZCRD1509

2.NC
1.VE RR1
V1

3.N
1.P

2.E
>

2.E
WHT.T TR101 HEATER CONTROL J1903 IL-2P J1905
U J1912
AC100V
B.DRAWINGS

TH101 PART P1912 P1903 P1905

1.RED

3.BLK
V （100W） CHG -215 （W305) ZCRD1457※
(W307)
WHT.T (OPTION)
UTH ZCRD1552※
+12V
TRANSCEIVER UNIT

B －29
WHT
C2 C101 + C102 J1505

1.P

2.N
BLK 1000μ 2200p B2P-VH

1.VERR
RED B102
ΦZE 16V 50V

2.E
YEL 1.MU2
ΦZ
>

SE 2.NC B3P-VH
PC1501 1.R1
BLU 3.MV2
ΦA S.G. S.G.
JMA-9100 Instruction Manual

4.NC B201 H-7EPRD0035 2.NC R2 R1

4.S4 B6P-VH
1.2kΩ 1.2kΩ
E SHIELD 5.NC 3.R2
30W 30W

J 1504
P1504
6.GND

1 0 J1
WHT

1 0P1
ΦB ENCODER CHT-71A1 (W304)

J1503
5

2.NC

4.NC
ZCRD1316※

1.M1

3.M2

5.M3
1.S1
2.S2
3.S3

5.S5
6.S6

J1502
BLK
BLK
NKE-1139 (AC110V)

S.G. CFA-255
P1502 BRAKE CIRCUIT
TB104 （W303) ZCRD1276※ J81 P81 P1503 WC1
1 AC100V
PTI WHT
MOTOR
TRANSCEIVER UNIT

BLK MOTOR DRIVER

PTE WHT CBP-205 B101 CBD-2001
BRN
LVR H-7BDRD0049 MOTOR
PMS J82
1
P82
BL U
E RE D
TXI BLK

ZCRD1179※
TXE
TRANSCEIVER UNIT

S.G.
VERR1
E
PM NJU-84
SCANNER INTERCONNECTION
CAX-14
B.6.10
NKE-1139PM (AC100V) Sﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
空中線機内接続図
 SAFETY SWITCH CSD-657
S101
S-32
（W301) ZCRD1287※ RED 2 3 WHT （W302) ZCRD1288※
RED.T 5 6 RED.T
BLK.T 8 9 BLK.T
BRAKE CIRCUIT A
CFA-261
120Ω
30W
×4
BRAKE CIRCUIT B
R1 CFA-262
R2 330Ω
30W ×1

Fig B-27: Interconnection Diagram of NKE-1139 (AC220V)

R3 R1 (W309)
(W308) (W310) ZCRD1543※
ZCRD1553※ ZCRD1544※ R4
P1921 P1911
P1941 J1941 J1921 J1911
RED 1-350209-0

1.BKH1

3.BKH2

1.BKS1
2.BKS2
1.+12V 1-350210-0
2.NC

2.NC
3.+12VE
S3B-XH-A
BRAKE CONTROL CIRCUIT
CCB-655
B.6 Interconnection Diagram of Scanner Unit

TB103
U1

1.VERR
B2PS-VH
W401 7ZCRD1509

2.NC
1.VERR
V1

3.N
1.P

2.E
2.E
WHT.T TR101 HEATER CONTROL J1903 IL-2P J1905
U J1912
AC100V

TH101 PART P1912 P1903 P1905

1.RED

3.BLK
V （100W） CHG -215 （W305) ZCRD1457※
(W307)
WHT.T (OPTION)
UTH ZCRD1552※
+12V
TRANSCEIVER UNIT

B －30
WHT
C2 C101 + C102 J1505

1.P

2.N
BLK 1000μ 2200p B2P-VH

1.VERR
RED B102
ΦZE 16V 50V

2.E
YEL 1.MU2
ΦZ SE 2.NC
PC1501 1.R1
B3P-VH
BLU 3.MV2
ΦA S.G. S.G.
4.NC B201 H-7EPRD0034 2.NC R2 R1

4.S4 B6P-VH
1.2kΩ 1.2kΩ
E SHIELD 5.NC 3.R2
30W 30W

J 1504
P1504
6.GND

1 0 J1
WHT

1 0P1
ΦB ENCODER CHT-71A1 (W304)

J1503
5

2.NC

4.NC
ZCRD1316※

1.M1

3.M2

5.M3
1.S1
2.S2
3.S3

5.S5
6.S6

J1502
BLK
BLK
NKE-1139 (AC220V)

S.G. CFA-255
P1502 BRAKE CIRCUIT
TB104 （W303) ZCRD1276※ J81 P81 P1503 WC1
1 AC220V
PTI WHT
MOTOR
>

TRANSCEIVER UNIT

BLK MOTOR DRIVER

PTE WHT CBP-205 B101 CBD-2000
B.DRAWINGS

BRN
LVR H-7BDRD0049 MOTOR
PMS J82
1
P82
BL U
E RE D
TXI BLK

ZCRD1179※
TXE
>

TRANSCEIVER UNIT
JMA-9100 Instruction Manual

S.G.
VERR1
E
PM NJU-84
SCANNER INTERCONNECTION
CAX-14
B.6.11
NKE-1139PM (AC220V) Sﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
空中線機内接続図
 B
ANTENNA
Ａ205
H-7ANRD0018
RECEIVER UNIT NRG-229
B.6 Interconnection Diagram of Scanner Unit

Ａ203 FILTER DUMMY

TL378A
RF CIRCUIT
IF CIRCUIT CAE-499 CAF-595 ③ ③
TRHPL

S.G.
J101 J102 ① ② ② ① MAG Ｖ101
IL-9P IL-7P M1555
2.TGTE

4.-15V

6.+15V
5.MPS
4.TNC

7.GND
1.TGT
6.VDE

3.TNL
1.BS3
2.BS2
3.BS1

8.+5V

5.TNI

Ａ201
9.NC
7.VD

GRN
NJC 3317

YEL
P3001 P3002 RECEIVER UN IT
INTERCONNECTION MODULATOR UNIT (W106)
CMA-902 NMA-553 Z CRD1230※

MD-12N1 MD-12N1
(W001) (W002)

CD201
ZC RD 1217※ ZC RD1218※
P1109 P1110 C201

Fig B-28: Interconnection Diagram of NTG-3230

(W003)
ZCRD1219※ J2102 0.01UF 1KV
IL-10P
P1111 P2102 (W103) 4 6
11.TRG2
5.MicPS
6.VDINE

5.TGTE
1.MONI

10.GND

1.SHORT
7.VDIN

7.-15V

9.+15V

1.SHORT
4.TNC

1.RXD
2.TXD

4.GND

ZC RD 1227※

CD202
4.TGT

T1
3.GSE

6.TNL
1.BS3
2.BS2
3.BS1

8.+5V

3.+5V
8.TNI
2.GS

2.MAGI 2.MAGI
3.X1 No.2 2 PULSE TRANS
3.X1
J1109 J1110 J1191 4.X2 4.X2 No.1 1 H-7LPRD 0122
IL-G-8P IL-G -11P

R201
J1 IL-4P 5.TI MODULATOR CIRCUIT

150Ω
5.TI
IL -G-12P

IL-G-6P 3 5 S.G.
J1111

6.TIE

ZCRD 1229※ 8W
6.TI E CFR-229
1.TIY
7.+15V CPA-264 J2103 (W104) C202

P2103
7.+15V 0.22UF 200V
2.TIYE
8.GND 8.GND 350209-2 ZC RD 1228※ MAG FILTER CIRCUIT
3.BP J2101 220pF×5
9.N C 9.NC 1.X1
>

4.BPE 1586514-2 2.X2

10.NC

(W105)
10.NC
5.BZ

1.MH

3.MN
2.NC
MODULATOR UNIT

2.7KΩ
11.NC

0.22UF
B.DRAWINGS

R202

1/2W
6.BZE

C203

200V
12.NC INTERCONNECTION
J2 IL-G -4P CMB-407 S.G. S.G.
P2101
B3P-SHF
1.VD 1.HMCNT P1118 （W004）
J1118

BLK.T
2.VD E ZCRD1220※ W201
2.+15V ZCRD1231※

B －31
3.MTR+ 3.GND
4.MTR- (W005)
ZC RD1221※ S.G.
P1002
T/R CONTROL CIRCUIT P1103 P1003
1.+15V 1.+15V (W301)
CMC-1205R J1001
>

1.MH

3.MN
2.NC
2.+12V 2.+12V ZC RD1215※
350428-1 P1202
TB101

B8P-SHF
MSTBA2.5/11-G 3.GND 3.+8V

B8P-SHF
P101
JMA-9100 Instruction Manual

J1003
J1202

J1103

P1212
1.BP+ 4.GND 4.G ND J1002 1.M+
IL-3P B3P-NV
2.M-

2.GND
1586514-2 J1212

1.MU2

3.MV2
2.BP- 5.-15V 5.-15V 1.HMCN T 1.VERR
3.BZ+ 6.10V 6.10V 2.+15V
2.E
4.BZ- 7.10VE 7.10VE
POWER SUPPLY CIRCUIT 3.GND

P1211
RELAY FILTER CIRC UIT

IL-2P
5.TRIG+ 8.+5V 8.+5V

J 1211
CBD-1682A CSC-656

IL-3P
6.TRIG- P1104 P1004
7.MTR+ 1.MCT 1.MCT PC1201

2.NC

4.NC
B6P-SHF

1.U1

3.V1
2.MBK

B9P-SHF
2.MBK

J1004
8.MTR-

J1104
3.TI STOP 3.HSP J1201 (W303) ZCRD1484※
9.MTRE B4P-VH
10.VD+ 4.GND 4.HTER
5.MPS 5.TI STOP P1201
11.VD-
6.MIER 6.C2 J4 J5 J3 (W302)
(W006) 350209-1 350209-1 B02P-NV(LF)(SN） Z CRD1216※
J1112 J1113 J1114 J13 ZC RD1222※
7.GND

2.1A
1.2A

2.1A
1.2A

2.1A
1.2A
IL -G -9P IL-G-3P IL-G-3P IL-6P 8.MPS
J8 1.φZ 9.MIER

8.STABY_REQ

BLK
J1106

RED

RED
J1105

3.FAN_ERR2

BLK
3.FAN _ERR1
2.φZE

2.HVGATE1
IL-8P IL-G-5P

3.TISTOP1
I L-G -2P
3.φ A TB202

1.HTER1
P3

1.+12V
2.GND
4.+24V

1.+12V

1.+12V
7.+15V
4.PMS

5.GND

2.GND
2.PTE

7.TXE
5.GND

4.GND
4.φB
3.LVR

1.PW1
2.PW2
3.PW3

5.CNT

U0

V0
+48VG
6.+5V

U1

V1
1.PTI

6.TXI

8.NC

9.NC

2.C 2

+48V
5.+12V
NTG-3230

6.GND (W007) ZCRD1223※

(W014) HC3L2

WHT

RED.T
WHT.T
P1105

V1
RED
P8

U1

V0
U0
ZCRD1226※ (W013) ZCRD1225※ (W008) ZCRD1224※
(W203) ZCRD1232※
3L2 3L1 3L1
SCANNER DISPLAY
TB201 TB204 TB203 UNIT UNIT
TRIG-

MTRE
MTR+
MTR-
TRIG+

BP -/BZ-

+48VG
VERR

+12V
PMS
PTE

TXE

φZE

+48V
LVR
VD+
VD-

BP+

PTI

TXI

GND
BZ+

φB
φA
φZ
C2
E
E
DISPLAY UNIT SCANNER UNIT SCANNER DISPLAY
UNIT UNIT
TRANSCEIVER UNIT INTERCONNECTION
CMK-594
B.6.12 H-7ZCRD####*:
“#” means specification document No.
“*” means revision of the specfication document.
NTG-3230
送受信機機内接続図
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram

B.7 Terminal Board Connection Diagram

B －32
 DISPLAY UNIT NCD-4990
19-CORES COMPOSITE CABL E (J RC SUPPL Y)
SCANNER UNIT
B.7.1
C FQ-6912-**
RADAR H -2695111153
(J RC SUPPL Y) CQD-2097 T ERMIN AL BOARD
NKE-2103-6/6HS
(INTERSWITC H)
TB4101(AN T)
COA XI AL
1 VD+
2 VD-
SHI ELD W iring of PER FOR MANC E MONITOR
T B4201(ISW IN/OU T) 3 TRIG +
1 is com pleted .
1 VDIN 1 4 TRIG -
OR N J4 J3 P81
2 VDIN 1E 5 BP+ BLK .T/ SKY .T P1
BLU B LK BLU.T /GRY .T PTI
3 TRIG IN1 6 BP- PTI
250V-T TYCS-1 GR N 2A 2A
4 TRIG IN1E 7 BZ+ PTE PTE
3C-2V x 5 (MAX 30m ) WHT
VDR YE L WHT .T/ ORN.T T XI WHT
5 BPIN1 8 BZ- B RN TXI
Y EL 1A 1A T XE B RN
6 BPIN1E 9 MTR+ YE L.T/ PNK.T TXE
GRN WHT
7 BZIN1 10 MTR-
8 BZIN1E 11 MTRE J5 P82 P2
WH T-B LU PUR. T/ BRN.T J1 B LU B LU
9 MTRIN 1+ 12 (NC) L VR L VR
WH T-WH T Y EL.T/ PNK.T 2A SHIE LD R ED R ED
10 MTRIN 1- 13 +48V PMS PMS
R ED.T/ GR N. T ETIY B LK B LK
11 MTRIN 1E 14 +48VG E E
ORG B LK.T/ SK Y.T 1A
12 PWR IN1
BLK AGND
13 PWR IN1E CBD -1684A TB522 R ED.T/ GR N .T
PNK WHT.T/ ORN .T J2
14 PWR OU T1 ORN
J4407 BR N 1 + C OAXI AL EXBP
15 PWR OU T1E
RJ -45 L AN 2 VD
16 VDOU T1
17 VDOU T1E 2 ー AGND
R ED
18 TRIG OU T1 PUR .T/ BRN.T
VDE GR N
PERFORMANCE
19 TRIG OU T1E 3 FG
B LU.T /GRY .T YEL
EXBZ MONITOR
PUR COM+
CQD-1891 20 BPOU T1 BLK
(J RC SUPPL Y) 21 BPOU T1E WHT
AGND
WHT COM- NJU-85
RED 22 BZOUT1 CBD -1684A TB521
R
23 BZOUT1E 1 U
GRN WH T-YE L
G 24 MTROUT 1+ 2 V

5-1 P)
WH T-WH T
BL U 25 MTROUT 1- 3 FG W406 H- 7ZC RD1342 A
B ( Wir ing is com pleted .)
26 MTROUT 1E
GR Y CBD -1661 ACOU T1
H
B LK BA TT IN +
V

C DC4 2 3-1
9 0 4J4 BUS(D
BA TT IN -
H -2695110006 U
(J RC SUPPL Y) V
ECDIS 250V-T TYCS-1 W

CONNING 250V-T TYCS-1

DISPLAY
JMA-9100 Instruction Manual

TB4501(OPTION) TB4601(ALA RM) TB4401(EXT RAD AR)

1 NA V1TX+ 1 ARPAAL M+ 1 RBVD
>

2 NA V1TX- 2 ARPAAL M- 2 RBVD E

250V-T TYCS-1
3 NA V1RX+ 3 SYSALM + 3 ETIY3

B －33
DGPS
4 NA V1RX- 4 SYSALM + 4 ETIY3E
5 NA V2TX+ 5 PWR AL M+ 5 SVD 1
6 NA V2TX- 6 PWR AL M- 6 SVD 1E
ECHO 250V-T TYCS-1
7 NA V2RX+ 7 ARPAAC K+ 7 ETIY1
JMA-9110-6XA/JMA-9110-6XAH

SOU NDER 8 NA V2RX- 8 ARPAAC K- 8 ETIY1E

9 LOG RX+ 9 SYSACK+ 9 EXφA1
LOG 250V-T TYCS-1 10 LOG RX- 10 SYSACK- 10 EXφA1E
(NMEA0183) 11 AL MTX+ 11 PWR ACK+ 11 EXφB1
12 AL MTX- 12 PWR ACK- 12 EXφB1E
B.DRAWINGS

13 AL MRX+ 13 EXEVT+ 13 EXφZ1

14 AL MRX- 14 EXEVT- 14 EXφZ1E
>

15 ARPAT X+ 15 AISTX+ 15 SVD 2

16 ARPAT X- 16 AISTX- 16 SVD 2E
RED
17 JAR PA TX+ 17 AIS_TG 17 ETIY2
18 JAR PA TX- 18 AISRX+ 18 ETIY2E
19 NSKT X+ 19 AISRX- 19 EXφA2
20 NSKT X- 20 AIS_RG 20 EXφA2E
WHT
21 HD G RX+ 21 MNTTX + 21 EXφB2
22 HD G RX- 22 MNTTX - 22 EXφB2E
BLK
23 EXφZ2
250V-T TYCS-4 24 EXφZ2E
AIS 25 (NC )
26 (NC )
27 ACKOU T+
LOG 0. 6/1kV-D PYCYS-1.5 28 ACKOU T-
TB4801(L O G)
(200P /NM) 29 WMRST+
1 (N C)
30 WMRST-
2 (N C)
3 (N C)
250V -M PYCYS-7
GYRO 4 (N C)
5 P1+
T B4701(G YRO) 6 P1-
1 1/R1 7 (N C)
2 2/S1 8 (N C)
3 3/S2 9 S1+
4 S3 10 S2- FILTER AC IN
WHT 0.6/1kV-D PYCY-6
5 5/R2 11 (N C) U SHIP’S MAINS

Fig B-29: Terminal Board Connection Diagram of JMA-9110-6XA/JMA-9110-6XAH

6 (NC) 12 (N C) W AC100-115V/ AC220-240V 50/60H z 1φ
ALARM MONITORING B LK (X-BAND 10kW RADAR)
V
SYSTEM
( NEAREST AP PRO ACH)
B.7 Terminal Board Connection Diagram

0. 6/ 1kV-D PYCYS-1.5
JMA-9110-6XA/6XAH レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9110-6XA/6XAH

B
 DISPLAY UNIT NCD-4990T
19-CORES COMPOSITE CABL E (J RC SUPPL Y)
SCANNER UNIT
B.7.2
C FQ-6912-**
RADAR H -2695111153
(J RC SUPPL Y) CQD-2097 T ERMIN AL BOARD NKE-2103-6/6HS
(INTERSWITC H)
TB4101(AN T)
COA XI AL
1 VD+
2 VD-
SHI ELD W iring of PER FOR MANC E MONITOR
T B4201(ISW IN/OU T) 3 TRIG +
1 is com pleted .
1 VDIN 1 4 TRIG -
OR N J4 J3 P81
2 VDIN 1E 5 BP+ BLK .T/ SKY .T P1
BLU B LK BLU.T /GRY .T PTI
3 TRIG IN1 6 BP- PTI
250V-T TYCS-1 GR N 2A 2A
4 TRIG IN1E 7 BZ+ PTE PTE
3C-2V x 5 (MAX 30m ) WHT
VDR YE L WHT .T/ ORN.T T XI WHT
5 BPIN1 8 BZ- B RN TXI
Y EL 1A 1A T XE B RN
6 BPIN1E 9 MTR+ YE L.T/ PNK.T TXE
GRN WHT
JMA-9100 Instruction Manual

7 BZIN1 10 MTR-
8 BZIN1E 11 MTRE J5 P82 P2
WH T-B LU PUR. T/ BRN.T B LU
>

9 MTRIN 1+ 12 (NC) J1 L VR B LU
Y EL.T/ PNK.T L VR
WH T-WH T 2A SHIE LD R ED R ED
10 MTRIN 1- 13 +48V PMS PMS
R ED.T/ GR N. T ETIY B LK B LK
11 MTRIN 1E 14 +48VG E E
ORG B LK.T/ SK Y.T 1A
12 PWR IN1
BLK AGND
13 PWR IN1E TB401 R ED.T/ GR N .T
PNK WHT.T/ ORN .T J2
14 PWR OU T1 WHT- BLK ORN
J4407 BR N 1 + C OAXI AL EXBP
15 PWR OU T1E
RJ -45 L AN 2 VD
16 VDOU T1
BLK- BLK AGND
17 VDOU T1E 2 ー
R ED
18 TRIG OU T1 PUR .T/ BRN.T
VDE GR N
PERFORMANCE
GR N B LU.T /GRY .T EXBZ
19 TRIG OU T1E 3 FG YEL
B.DRAWINGS

PUR
20 BPOU T1
COM+ MONITOR
CQD-1891 BLK
(J RC SUPPL Y) 21 BPOU T1E WHT
AGND
>

WHT COM- NJU-85

RED 22 BZOUT1
R W408 H- 7ZC RD1344 A
23 BZOUT1E
WH T-YE L ( JRC SUPPLY)
GRN 24 MTROUT 1+
G

5-1 P)
WH T-WH T
BL U 25 MTROUT 1- CBD -1661 ACOU T1
B
26 MTROUT 1E BA TT IN + W407 H- 7ZC RD1343 A
GR Y BA TT IN - ( JRC SUPPLY)
H
WHT
B LK U
V BLK

C DC4 2 3-1
9 0 4J4 BUS(D
V
H -2695110006 W
GRN
(J RC SUPPL Y)
ECDIS 250V-T TYCS-1

CONNING 250V-T TYCS-1

DISPLAY TB4501(OPTION) TB4601(ALA RM) TB4401(EXT RAD AR) CBD -1684A TB 522
WHT -B LK
1 NA V1TX+ 1 ARPAAL M+ 1 RBVD 1 +
B LK-B LK
2 NA V1TX- 2 ARPAAL M- 2 RBVD E 2 ー
250V-T TYCS-1 GRN
3 NA V1RX+ 3 SYSALM + 3 ETIY3 3 FG

B －34
DGPS
4 NA V1RX- 4 SYSALM + 4 ETIY3E
5 NA V2TX+ 5 PWR AL M+ 5 SVD 1
6 NA V2TX- 6 PWR AL M- 6 SVD 1E CBD -1684A TB 521
ECHO 250V-T TYCS-1 WHT
7 NA V2RX+ 7 ARPAAC K+ 7 ETIY1 1 U
SOU NDER B LK
8 NA V2RX- 8 ARPAAC K- 8 ETIY1E 2 V
GRN
9 LOG RX+ 9 SYSACK+ 9 EXφA1 3 FG
LOG 250V-T TYCS-1 10 LOG RX- 10 SYSACK- 10 EXφA1E
(NMEA0183) 11 AL MTX+ 11 PWR ACK+ 11 EXφB1
12 AL MTX- 12 PWR ACK- 12 EXφB1E
13 AL MRX+ 13 EXEVT+ 13 EXφZ1
B.7 Terminal Board Connection Diagram

14 AL MRX- 14 EXEVT- 14 EXφZ1E

AC/DC CONVERTER UNIT
15 ARPAT X+ 15 AISTX+ 15 SVD 2
16 ARPAT X- 16 AISTX- 16 SVD 2E NBA-5135
RED
17 JAR PA TX+ 17 AIS_TG 17 ETIY2
18 JAR PA TX- 18 AISRX+ 18 ETIY2E
19 NSKT X+ 19 AISRX- 19 EXφA2
20 NSKT X- 20 AIS_RG 20 EXφA2E
WHT
21 HD G RX+ 21 MNTTX + 21 EXφB2
22 HD G RX- 22 MNTTX - 22 EXφB2E
JMA-9110-6XA/JMA-9110-6XAH (desktop)

BLK
23 EXφZ2
250V-T TYCS-4 24 EXφZ2E
AIS 25 (NC )
26 (NC )
27 ACKOU T+
LOG 0. 6/1kV-D PYCYS-1.5 28 ACKOU T-
TB4801(L O G)
(200P /NM) 29 WMRST+
1 (N C)
30 WMRST-
2 (N C)
3 (N C)
250V -M PYCYS-7
GYRO 4 (N C)
5 P1+ T B402
R ED
T B4701(G YRO) 6 P1- 1 U
WHT
1 1/R1 7 (N C) 2 V
B LK
2 2/S1 8 (N C) 3 W
3 3/S2 9 S1+
4 S3 10 S2- FILTER AC IN
R ED WHT 0.6/1kV-D PYCY-6
5 5/R2 11 (N C) U SHIP’S MAINS
B LK AC100-115V/ AC220-240V 50/60H z 1φ
6 (NC) 12 (N C) W
ALARM MONITORING WHT B LK (X-BAND 10kW RADAR)
V
SYSTEM
( NEAREST AP PRO ACH) W405 H -7ZC RD 1341A( JRC SUPPL Y)
0. 6/1kV-D PYCYS-1.5 Wiring is com pleted.
JMA-9110-6XA/6XAH レーダー（卓上型） 盤間接続図

Fig B-30: Terminal Board Connection Diagram of JMA-9110-6XA/JMA-9110-6XAH (desktop)

INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9110-6XA/6XAH(desktop)
 DISPLAY UNIT NCD-4990
19-CORES COMPOSITE CABL E (J RC SUPPL Y)
SCANNER UNIT
B.7.3
C FQ-6912-**
RADAR H -2695111153
(J RC SUPPL Y) CQD-2097 T ERMIN AL BOARD
NKE-2254-6HS
(INTERSWITC H)
TB4101(AN T)
COA XI AL
1 VD+
2 VD-
SHI ELD W iring of PER FOR MANC E MONITOR
T B4201(ISW IN/OU T) 3 TRIG +
1 is com pleted .
1 VDIN 1 4 TRIG -
OR N J4 J3 P81
2 VDIN 1E 5 BP+ BLK .T/ SKY .T P1
BLU B LK BLU.T /GRY .T PTI
3 TRIG IN1 6 BP- PTI
250V-T TYCS-1 GR N 2A 2A
4 TRIG IN1E 7 BZ+ PTE PTE
3C-2V x 5 (MAX 30m ) WHT
VDR YE L WHT .T/ ORN.T T XI WHT
5 BPIN1 8 BZ- B RN TXI
Y EL 1A 1A T XE B RN
6 BPIN1E 9 MTR+ YE L.T/ PNK.T TXE
GRN WHT
7 BZIN1 10 MTR-
8 BZIN1E 11 MTRE J5 P82 P2
WH T-B LU PUR. T/ BRN.T J1 B LU B LU
9 MTRIN 1+ 12 (NC) L VR L VR
WH T-WH T Y EL.T/ PNK.T 2A SHIE LD R ED R ED
10 MTRIN 1- 13 +48V PMS PMS
R ED.T/ GR N. T TRIG+ B LK B LK
11 MTRIN 1E 14 +48VG E E
ORG B LK.T/ SK Y.T 1A
12 PWR IN1
BLK TRIG-
13 PWR IN1E CBD -1684A TB522 R ED.T/ GR N .T
PNK WHT.T/ ORN .T J2
14 PWR OU T1 ORN
J4407 BR N 1 + C OAXI AL BP+
15 PWR OU T1E
RJ -45 L AN 2 VD
16 VDOU T1
17 VDOU T1E 2 ー BP-
R ED
18 TRIG OU T1 PUR .T/ BRN.T
VDE GR N
PERFORMANCE
19 TRIG OU T1E 3 FG
B LU.T /GRY .T YEL
BZ+ MONITOR
PUR COM+
CQD-1891 20 BPOU T1 BLK
(J RC SUPPL Y) 21 BPOU T1E WHT
BZ-
WHT COM- NJU-85
RED 22 BZOUT1 CBD -1684A TB521
R
JMA-9122-6XAH

23 BZOUT1E 1 U
GRN WH T-YE L
G 24 MTROUT 1+ 2 V

5-1 P)
WH T-WH T TB105
BL U 25 MTROUT 1- 3 FG W406 H- 7ZC RD1342 A
B 1 U
26 MTROUT 1E ( Wir ing is com pleted .)
GR Y 2 V
H CBD -1661 ACOU T1
3 UT H
B LK BA TT IN +
V

C DC4 2 3-1
9 0 4J4 BUS(D
BA TT IN -
H -2695110006 U
(J RC SUPPL Y) V
ECDIS 250V-T TYCS-1 W

CONNING 250V-T TYCS-1

DISPLAY
JMA-9100 Instruction Manual

TB4501(OPTION) TB4601(ALA RM) TB4401(EXT RAD AR)

1 NA V1TX+ 1 ARPAAL M+ 1 RBVD
>

2 NA V1TX- 2 ARPAAL M- 2 RBVD E

250V-T TYCS-1
3 NA V1RX+ 3 SYSALM + 3 ETIY3

B －35
DGPS “D” HEATER OPTION
4 NA V1RX- 4 SYSALM + 4 ETIY3E
5 NA V2TX+ 5 PWR AL M+ 5 SVD 1 C IRCU IT BR EAKER
6 NA V2TX- 6 PWR AL M- 6 SVD 1E 0.6/1kV-DPYCY S-1. 5 5A ( SHIP YAR D SUPPLY)
ECHO 250V-T TYCS-1
7 NA V2RX+ 7 ARPAAC K+ 7 ETIY1 AC100V,1φ,100W
SOU NDER 8 NA V2RX- 8 ARPAAC K- 8 ETIY1E 0.6/1kV-D PYCYS-1.5
9 LOG RX+ 9 SYSACK+ 9 EXφA1
LOG 250V-T TYCS-1 10 LOG RX- 10 SYSACK- 10 EXφA1E
(NMEA0183) 11 AL MTX+ 11 PWR ACK+ 11 EXφB1 N BL -175 0.6/1kV-D PYCYS-1.5
12 AL MTX- S TEP- DOWN
SHIP’S MAINS
12 PWR ACK- 12 EXφB1E
B.DRAWINGS

T RA NSF OR MER AC220V , 1φ, fo r HEAT ER

13 AL MRX+ 13 EXEVT+ 13 EXφZ1
14 AL MRX- 14 EXEVT- 14 EXφZ1E
>

15 ARPAT X+ 15 AISTX+ 15 SVD 2

16 ARPAT X- 16 AISTX- 16 SVD 2E
RED
17 JAR PA TX+ 17 AIS_TG 17 ETIY2
18 JAR PA TX- 18 AISRX+ 18 ETIY2E
19 NSKT X+ 19 AISRX- 19 EXφA2
20 NSKT X- 20 AIS_RG 20 EXφA2E
WHT
21 HD G RX+ 21 MNTTX + 21 EXφB2
22 HD G RX- 22 MNTTX - 22 EXφB2E
BLK
23 EXφZ2
250V-T TYCS-4 24 EXφZ2E
AIS 25 (NC )
26 (NC )
27 ACKOU T+
LOG 0. 6/1kV-D PYCYS-1.5 28 ACKOU T-
TB4801(L O G)
(200P /NM) 29 WMRST+
1 (N C)
30 WMRST-
2 (N C)
3 (N C)
250V -M PYCYS-7

Fig B-31: Terminal Board Connection Diagram of JMA-9122-6XAH

GYRO 4 (N C)
5 P1+
T B4701(G YRO) 6 P1-
1 1/R1 7 (N C)
2 2/S1 8 (N C)
3 3/S2 9 S1+
4 S3 10 S2- FILTER AC IN
WHT 0.6/1kV-D PYCY-6
5 5/R2 11 (N C) U SHIP’S MAINS
6 (NC) 12 (N C) W AC100-115V/ AC220-240V 50/60H z 1φ
ALARM MONITORING B LK (X-BAND 25kW RADAR)
V
SYSTEM
( NEAREST AP PRO ACH)
B.7 Terminal Board Connection Diagram

0. 6/1kV-D PYCYS-1.5
JMA-9122-6XAH レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XAH

B
 DISPLAY UNIT NCD-4990T
19-CORES COMPOSITE CABL E (J RC SUPPL Y)
SCANNER UNIT
B.7.4
C FQ-6912-**
RADAR H -2695111153
(J RC SUPPL Y) CQD-2097 T ERMIN AL BOARD
NKE-2254-6HS
(INTERSWITC H)
TB4101(AN T)
C OA XI AL
1 VD+
2 VD-
SHI ELD W iring of PER FOR MANC E MONITOR
T B4201(ISW IN/OU T) 3 TRIG +
1 is com pleted .
1 VDIN 1 4 TRIG -
OR N J4 J3 P81
2 VDIN 1E 5 BP+ BLK .T/ SKY .T P1
BLU B LK BLU.T /GRY .T PTI
3 TRIG IN1 6 BP- PTI
250V-T TYCS-1 GR N 2A 2A
4 TRIG IN1E 7 BZ+ PTE PTE
3C-2V x 5 (MAX 30m ) WHT
VDR YE L WHT .T/ ORN.T T XI WHT
5 BPIN1 8 BZ- B RN TXI
Y EL AC/DC CONVERTER UNIT 1A 1A T XE B RN
6 BPIN1E 9 MTR+ YE L.T/ PNK.T TXE
GRN WHT
JMA-9100 Instruction Manual

7 BZIN1 10 MTR-

WH T-B LU
8 BZIN1E 11 MTRE
NBA-5135 PUR. T/ BRN.T
J5 P82
B LU P2
>

9 MTRIN 1+ 12 (NC) J1 L VR B LU
Y EL.T/ PNK.T L VR
WH T-WH T 2A SHIE LD R ED R ED
10 MTRIN 1- 13 +48V PMS PMS
R ED.T/ GR N. T TRIG+ B LK B LK
11 MTRIN 1E 14 +48VG E E
ORG B LK.T/ SK Y.T CBD -1684A TB 522 1A
12 PWR IN1 WHT -B LK
BLK 1 + TRIG-
13 PWR IN1E TB401 R ED.T/ GR N .T B LK-B LK
PNK WHT.T/ ORN .T 2 ー
14 PWR OU T1 WHT- BLK GRN J2 ORN
J4407 BR N 1 + 3 FG C OAXI AL BP+
15 PWR OU T1E
RJ -45 L AN 2 VD
16 VDOU T1
BLK- BLK BP-
17 VDOU T1E 2 ー
R ED CBD -1684A TB 521 VDE PERFORMANCE
18 TRIG OU T1 PUR .T/ BRN.T WHT GR N
GR N B LU.T /GRY .T 1 U BZ+
19 TRIG OU T1E 3 FG B LK YEL
B.DRAWINGS

PUR
20 BPOU T1
2 V COM+ MONITOR
CQD-1891 GRN BLK
3 FG BZ-
(J RC SUPPL Y) 21 BPOU T1E WHT
>

WHT COM- NJU-85

RED 22 BZOUT1
R
23 BZOUT1E W 408 H-7ZC RD134 4A
GRN WH T-YE L ( JRC SUPPLY)
G 24 MTROUT 1+

5-1 P)
WH T-WH T TB105
BL U 25 MTROUT 1- CBD -1661 ACOU T1
B 1 U
26 MTROUT 1E BA TT IN + W407 H- 7ZC RD1343 A
GR Y ( JRC SUPPLY) 2 V
H BA TT IN -
WHT 3 UT H
B LK U
V BLK

C DC4 2 3-1
9 0 4J4 BUS(D
V
H -2695110006 W
GRN
(J RC SUPPL Y)
ECDIS 250V-T TYCS-1

CONNING 250V-T TYCS-1

DISPLAY TB4501(OPTION) TB4601(ALA RM) TB4401(EXT RAD AR)
JMA-9122-6XAH (desktop)

1 NA V1TX+ 1 ARPAAL M+ 1 RBVD

2 NA V1TX- 2 ARPAAL M- 2 RBVD E
250V-T TYCS-1
3 NA V1RX+ 3 SYSALM + 3 ETIY3

B －36
DGPS “D” HEATER OPTION
4 NA V1RX- 4 SYSALM + 4 ETIY3E
5 NA V2TX+ 5 PWR AL M+ 5 SVD 1 C IRCU IT BR EAKER
6 NA V2TX- 6 PWR AL M- 6 SVD 1E 0.6/1kV-DPYCY S-1. 5 5A ( SHIP YAR D SUPPLY)
ECHO 250V-T TYCS-1
7 NA V2RX+ 7 ARPAAC K+ 7 ETIY1 AC100V,1φ,100W
SOU NDER 8 NA V2RX- 8 ARPAAC K- 8 ETIY1E 0.6/1kV-D PY CYS-1.5
9 LOG RX+ 9 SYSACK+ 9 EXφA1
LOG 250V-T TYCS-1 10 LOG RX- 10 SYSACK- 10 EXφA1E
(NMEA0183) 11 AL MTX+ 11 PWR ACK+ 11 EXφB1 N BL -175 0.6/1kV-D PYCYS-1.5
12 AL MTX- S TEP- DOWN
SHIP’S MAINS
12 PWR ACK- 12 EXφB1E
T RA NSF OR MER AC220V , 1φ, fo r HEAT ER
13 AL MRX+ 13 EXEVT+ 13 EXφZ1
B.7 Terminal Board Connection Diagram

14 AL MRX- 14 EXEVT- 14 EXφZ1E

15 ARPAT X+ 15 AISTX+ 15 SVD 2
16 ARPAT X- 16 AISTX- 16 SVD 2E
RED
17 JAR PA TX+ 17 AIS_TG 17 ETIY2
18 JAR PA TX- 18 AISRX+ 18 ETIY2E
19 NSKT X+ 19 AISRX- 19 EXφA2
20 NSKT X- 20 AIS_RG 20 EXφA2E
WHT
21 HD G RX+ 21 MNTTX + 21 EXφB2
22 HD G RX- 22 MNTTX - 22 EXφB2E
BLK
23 EXφZ2
250V-T TYCS-4 24 EXφZ2E
AIS 25 (NC )
26 (NC )
27 ACKOU T+
LOG 0.6/1kV-D PYCYS-1.5 28 ACKOU T-
TB4801(L O G)
(200P /NM) 29 WMRST+
1 (N C)
30 WMRST-
2 (N C)
3 (N C)
250V -M PYCYS-7
GYRO 4 (N C)
5 P1+ T B402
R ED
T B4701(G YRO) 6 P1- 1 U
WHT
1 1/R1 7 (N C) 2 V
B LK
2 2/S1 8 (N C) 3 W

Fig B-32: Terminal Board Connection Diagram of JMA-9122-6XAH (desktop)

3 3/S2 9 S1+
4 S3 10 S2- FILTER AC IN 0.6/1kV-D PYCY-6
R ED WHT
5 5/R2 11 (N C) U SHIP’S MAINS
B LK
6 (NC) 12 (N C) W AC100-115V/ AC220-240V 50/60H z 1φ
ALARM MONITORING WHT B LK (X-BAND 25kW RADAR)
V
SYSTEM
( NEAREST AP PRO ACH) W405 H -7ZC RD 1341A( JRC SUPPL Y)
0. 6/1kV-D PYCYS-1.5 Wiring is com pleted.
JMA-9122-6XAH レーダー（卓上型） 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XAH(desktop)
 DISPLAY UNIT NCD-4990
19-C OR ES CO MPOSITE CABL E (JRC SU PPL Y)
SCANNER UNIT
B.7.5
RADAR H -2695111153 H-2695110056
(J RC SUPPL Y) CQD-2097 T ERMIN AL BOARD
NKE-1125-61/62/91/92
(INTERSWITC H)
TB4101(AN T)
1
1 VD+
2 VD-
2 W iring of PER FOR MANC E MONITOR
T B4201(ISW IN/OU T) 3 TRIG +
1 is com pleted .
1 VDIN 1 4 TRIG -
3 P81
2 VDIN 1E 5 BP+ P1
BLU PTI
3 TRIG IN1 6 BP- PTI
250V-T TYCS-1 4
4 TRIG IN1E 7 BZ+ PTE PTE
3C-2V x 5 (MAX 30m ) T B101 TB102 WHT
VDR YE L T XI WHT
5 BPIN1 8 BZ- 3 RE D B RN TXI
OR N 1 BP+ 1 +48V T XE B RN
6 BPIN1E 9 MTR+ BLU TXE
GRN WHT 2 BP- 2 +48VG
7 BZIN1 10 MTR- 4
3 BZ+ 3
8 BZIN1E 11 MTRE YEL P82 P2
WH T-B LU 4 BZ- 4 U1 B LU
9 MTRIN 1+ 12 (NC) 2 L VR B LU
GRN L VR
WH T-WH T R ED 5 TRIG + 5 V1 R ED R ED
10 MTRIN 1- 13 +48V PMS PMS
B LU 6 TRIG - 6 W1 B LK B LK
11 MTRIN 1E 14 +48VG ORN E E
ORG 7 MTR+
12 PWR IN1 WHT
BLK 8 MTR-
13 PWR IN1E
PNK 9 MTRE TB105
14 PWR OU T1 1
J4407 BR N 10 VD+ 1 U
15 PWR OU T1E
RJ -45 L AN 2 11 VD- 2 V
16 VDOU T1
3 UT H
17 VDOU T1E PERFORMANCE
R ED
18 TRIG OU T1
19 TRIG OU T1E MONITOR
PUR
CQD-1891 20 BPOU T1
(J RC SUPPL Y) 21 BPOU T1E
WHT NJU-85
RED 22 BZOUT1
R
23 BZOUT1E
GRN WH T-YE L
G 24 MTROUT 1+

5-1 P)
WH T-WH T
BL U 25 MTROUT 1- CBD -1661 ACOU T1
B
26 MTROUT 1E BA TT IN +
GR Y BA TT IN -
H
JMA-9122-6XA/9XA

Y EL
B LK U
V GRN

C DC4 2 3-1
9 0 4J4 BUS(D
V
H -2695110006 W “D” HEATER OPTION
(J RC SUPPL Y) C IRCU IT BR EAKER
ECDIS 250V-T TYCS-1 0.6/1kV-DPYCY S-1. 5 5A ( SHIP YAR D SUPPLY)
AC100V,1φ,100W
0.6/1kV-DPYC YS-1.5
CONNING 250V-T TYCS-1
DISPLAY
JMA-9100 Instruction Manual

TB4501(OPTION) TB4601(ALA RM) TB4401(EXT RAD AR) N BL -175 0.6/1kV-D PYCYS-1.5 SHIP’S MAINS
1 NA V1TX+ 1 ARPAAL M+ 1 RBVD S TEP- DOWN
T RA NSF OR MER AC220V , 1φ, fo r HEAT ER
>

2 NA V1TX- 2 ARPAAL M- 2 RBVD E

250V-T TYCS-1
3 NA V1RX+ 3 SYSALM + 3 ETIY3

B －37
DGPS
4 NA V1RX- 4 SYSALM + 4 ETIY3E
5 NA V2TX+ 5 PWR AL M+ 5 SVD 1
6 NA V2TX- 6 PWR AL M- 6 SVD 1E
ECHO 250V-T TYCS-1
7 NA V2RX+ 7 ARPAAC K+ 7 ETIY1
SOU NDER 8 NA V2RX- 8 ARPAAC K- 8 ETIY1E
9 LOG RX+ 9 SYSACK+ 9 EXφA1
LOG 250V-T TYCS-1 10 LOG RX- 10 SYSACK- 10 EXφA1E
(NMEA0183) 11 AL MTX+ 11 PWR ACK+ 11 EXφB1
12 AL MTX- 12 PWR ACK- 12 EXφB1E
B.DRAWINGS

13 AL MRX+ 13 EXEVT+ 13 EXφZ1

14 AL MRX- 14 EXEVT- 14 EXφZ1E
>

15 ARPAT X+ 15 AISTX+ 15 SVD 2

16 ARPAT X- 16 AISTX- 16 SVD 2E
RED
17 JAR PA TX+ 17 AIS_TG 17 ETIY2
18 JAR PA TX- 18 AISRX+ 18 ETIY2E
19 NSKT X+ 19 AISRX- 19 EXφA2
20 NSKT X- 20 AIS_RG 20 EXφA2E
WHT
21 HD G RX+ 21 MNTTX + 21 EXφB2
22 HD G RX- 22 MNTTX - 22 EXφB2E
BLK
23 EXφZ2
250V-T TYCS-4 24 EXφZ2E
AIS 25 (NC )
26 (NC )
27 ACKOU T+
LOG 0. 6/1kV-D PYCYS-1.5 28 ACKOU T-
TB4801(L O G)
(200P /NM) 29 WMRST+
1 (N C)
30 WMRST-
2 (N C)
3 (N C)
250V -M PYCYS-7
GYRO 4 (N C)
5 P1+

Fig B-33: Terminal Board Connection Diagram of JMA-9122-6XA/9XA

T B4701(G YRO) 6 P1-
1 1/R1 7 (N C)
2 2/S1 8 (N C)
3 3/S2 9 S1+
4 S3 10 S2- FILTER AC IN
WHT 0.6/1kV-D PYCY-6
5 5/R2 11 (N C) U SHIP’S MAINS
6 (NC) 12 (N C) W AC100-115V/ AC220-240V 50/60H z 1φ
ALARM MONITORING B LK (X-BAND 25kW RADAR)
V
SYSTEM
( NEAREST AP PRO ACH)
B.7 Terminal Board Connection Diagram

0. 6/1kV-D PYCYS-1.5
JMA-9122-6XA/9XA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XA/9XA

B
 DISPLAY UNIT NCD-4990
19-C OR ES CO MPOSITE CABL E (JRC SU PPL Y)
SCANNER UNIT
B.7.6
RADAR H -2695111153 H-2695110056
(J RC SUPPL Y) CQD-2097 T ERMIN AL BOARD
NKE-1129-71/72/91/92
(INTERSWITC H)
TB4101(AN T)
1
1 VD+
2 VD-
2 W iring of PER FOR MANC E MONITOR
T B4201(ISW IN/OU T) 3 TRIG +
1 is com pleted .
1 VDIN 1 4 TRIG -
3 TB103 TB105 TB104 P81
2 VDIN 1E 5 BP+ YEL P1
1 U1 1 U GRY 1 PTI
BLU PTI
3 TRIG IN1 6 BP- GR N PTI
250V-T TYCS-1 4 2 V1 2 V 2 PTE
4 TRIG IN1E 7 BZ+ PTE PTE
3C-2V x 5 (MAX 30m ) 3 W1 3 UT H BLU 3 L VR WHT
VDR YE L T XI WHT
5 BPIN1 8 BZ- OR N R ED B RN TXI
OR N 4 +12v 4 PMS T XE B RN
6 BPIN1E 9 MTR+ TXE
GRN WHT 5 C2 5 E
JMA-9100 Instruction Manual

7 BZIN1 10 MTR- WHT 4

6 Φ ZE 6 TXI
8 BZIN1E 11 MTRE 3 P82 P2
WH T-B LU 7 ΦZ 7 TXE B LU
>

9 MTRIN 1+ 12 (NC) L VR B LU
1 L VR
WH T-WH T R ED 8 ΦA 8 (NC ) R ED R ED
10 MTRIN 1- 13 +48V PUR PMS
B LU 9 E 9 VER R B LK PMS
11 MTRIN 1E 14 +48VG E B LK
2 BLK E
ORG 10 ΦB 10 E
12 PWR IN1
BLK
13 PWR IN1E
PNK
14 PWR OU T1
J4407 BR N
15 PWR OU T1E
RJ -45 L AN 2
16 VDOU T1
17 VDOU T1E PERFORMANCE
R ED
18 TRIG OU T1
19 TRIG OU T1E
B.DRAWINGS

PUR “D” HEATER OPTION MONITOR

CQD-1891 20 BPOU T1
CIRCU IT BREAKER
(J RC SUPPL Y) 21 BPOU T1E
>

WHT 0.6/1kV-D PYCYS-1.5 5A ( SHIP YA RD SUPPLY ) NJU-85

RED 22 BZOUT1
R A C100V,1φ ,100W
23 BZOUT1E
WH T-YE L 0.6/1kV-DPYCY S-1.5
GRN 24 MTROUT 1+
G

5-1 P)
WH T-WH T
BL U 25 MTROUT 1- CBD -1661 ACOU T1
B
26 MTROUT 1E BA TT IN +
GR Y NBL -175 0.6/1kV -DPYCYS-1.5
H BA TT IN -
JMA-9123-7XA/9XA

Y EL STEP -DOWN SHIP’S MAINS

U TRA NSFORME R
B LK GRN AC 220V, 1φ, for H EATER
V

C DC4 2 3-1
9 0 4J4 BUS(D
V
H -2695110006 W
(J RC SUPPL Y)
ECDIS 250V-T TYCS-1
19-CORES COMPOSIT E CA BLE (JR C SUPPL Y)
H-2695110056 F R-9 FLEXIBLE WAVEGUIDE
CONNING 250V-T TYCS-1 (JRC SUPPLY)
DISPLAY TB4501(OPTION) TB4601(ALA RM) TB4401(EXT RAD AR)
1 NA V1TX+ 1 ARPAAL M+ 1 RBVD
2 NA V1TX- 2 ARPAAL M- 2 RBVD E
250V-T TYCS-1
3 NA V1RX+ 3 SYSALM + 3 ETIY3

B －38
DGPS
4 NA V1RX- 4 SYSALM + 4 ETIY3E
5 NA V2TX+ 5 PWR AL M+ 5 SVD 1
6 NA V2TX- 6 PWR AL M- 6 SVD 1E
ECHO 250V-T TYCS-1
7 NA V2RX+ 7 ARPAAC K+ 7 ETIY1
SOU NDER 8 NA V2RX- 8 ARPAAC K- 8 ETIY1E TB201 T B203 TB204
1 OR N GR Y
9 LOG RX+ 9 SYSACK+ 9 EXφA1 1 VD + 1 +12V 1 PTI
250V-T TYCS-1 WHT
LOG 10 LOG RX- 10 SYSACK- 10 EXφA1E 2 VD - 2 C2 2 PTE
(NMEA0183) 2 R ED
11 AL MTX+ 11 PWR ACK+ 11 EXφB1 3 TR IG+ 3 ΦZE 3 L VR
3 BLU
12 AL MTX- 12 PWR ACK- 12 EXφB1E 4 TR IG- 4 ΦZ 4 PMS
3 1
13 AL MRX+ 13 EXEVT+ 13 EXφZ1 5 BP+ 5 ΦA 5 E
B.7 Terminal Board Connection Diagram

4
14 AL MRX- 14 EXEVT- 14 EXφZ1E 6 BP-/BZ- 6 E 6 TXI
4 2
15 ARPAT X+ 15 AISTX+ 15 SVD 2 7 BZ+ 7 ΦB 7 TXE
ORN
16 ARPAT X- 16 AISTX- 16 SVD 2E 8 MTR + 8 8 (N C)
RED WHT R ED P UR
17 JAR PA TX+ 17 AIS_TG 17 ETIY2 9 MTR - 9 +48V 9 VER R
BLU BLK
18 JAR PA TX- 18 AISRX+ 18 ETIY2E 10 MTR E 10 +48V G 10 E
19 NSKT X+ 19 AISRX- 19 EXφA2
20 NSKT X- 20 AIS_RG 20 EXφA2E
WHT
21 HD G RX+ 21 MNTTX + 21 EXφB2
22 HD G RX- 22 MNTTX - 22 EXφB2E T B202
BLK YE L
23 EXφZ2 1 U1
GRN
250V-T TYCS-4 24 EXφZ2E 2 V1
AIS 25 (NC ) 3
YEL
26 (NC ) 4 U0
GR N
27 ACKOU T+ 5 V0
LOG 0. 6/1kV-D PYCYS-1.5 28 ACKOU T- 6
TB4801(L O G)
(200P /NM) 29 WMRST+
1 (N C)
30 WMRST-
2 (N C)
3 (N C)
250V -M PYCYS-7
GYRO 4 (N C)
5 P1+
TRANSCEIVER UNIT NTG-3225

Fig B-34: Terminal Board Connection Diagram of JMA-9123-7XA/9XA

T B4701(G YRO) 6 P1-
1 1/R1 7 (N C)
2 2/S1 8 (N C)
3 3/S2 9 S1+
4 S3 10 S2- FILTER AC IN
WHT 0.6/1kV-D PY CY-6
5 5/R2 11 (N C) U SHIP’S MAINS
6 (NC) 12 (N C) W AC100-115V/ AC220-240V 50/60H z 1φ
ALARM MONITORING B LK (X-BAND 25kW RADAR)
V
SYSTEM
( NEAREST AP PRO ACH)
0. 6/1kV-D PYCYS-1.5
JMA-9123-7XA/9XA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9123-7XA/9XA
 DISPLAY UNIT NCD-4990
19-C OR ES CO MPOSITE CABL E (JRC SU PPL Y)
SCANNER UNIT
B.7.7
RADAR H -2695111153 H-2695110056
(J RC SUPPL Y) CQD-2097 T ERMIN AL BOARD
NKE-1130-1/2
(INTERSWITC H)
TB4101(AN T)
1
1 VD+
2 VD-
2 W iring of PER FOR MANC E MONITOR
T B4201(ISW IN/OU T) 3 TRIG +
1 is com pleted .
1 VDIN 1 4 TRIG -
3 P81
2 VDIN 1E 5 BP+ P1
BLU PTI
3 TRIG IN1 6 BP- PTI
250V-T TYCS-1 4
4 TRIG IN1E 7 BZ+ PTE PTE
3C-2V x 5 (MAX 30m ) T B101 TB102 WHT
VDR YE L T XI WHT
5 BPIN1 8 BZ- 3 RE D B RN TXI
OR N 1 BP+ 1 +48V T XE B RN
6 BPIN1E 9 MTR+ BLU TXE
GRN WHT 2 BP- 2 +48VG
7 BZIN1 10 MTR- 4 YEL
3 BZ+ 3 U1
8 BZIN1E 11 MTRE GRN P82 P2
WH T-B LU 4 BZ- 4 V1 B LU
9 MTRIN 1+ 12 (NC) 2 L VR B LU
5 TRIG + 5 W1 L VR
WH T-WH T R ED R ED R ED
10 MTRIN 1- 13 +48V PMS PMS
B LU 6 TRIG - 6 B LK B LK
11 MTRIN 1E 14 +48VG ORN E E
ORG 7 MTR+ 7
12 PWR IN1 WHT
BLK 8 MTR- 8
13 PWR IN1E
PNK 9 MTRE 9
14 PWR OU T1 1
J4407 BR N 10 VD+ 10 UT H
15 PWR OU T1E
RJ -45 L AN 2 11 VD- 11 U
16 VDOU T1
12 V
17 VDOU T1E PERFORMANCE
R ED
18 TRIG OU T1
JMA-9132-SA

19 TRIG OU T1E MONITOR

PUR
CQD-1891 20 BPOU T1
(J RC SUPPL Y) 21 BPOU T1E
WHT NJU-84
RED 22 BZOUT1
R
23 BZOUT1E
GRN WH T-YE L
G 24 MTROUT 1+

5-1 P)
WH T-WH T
BL U 25 MTROUT 1- CBD -1661 ACOU T1
B
26 MTROUT 1E BA TT IN +
GR Y BA TT IN -
H
Y EL
B LK U
V GRN

C DC4 2 3-1
9 0 4J4 BUS(D
V
H -2695110006 W “D” HEATER OPTION
(J RC SUPPL Y) C IRCU IT BR EAKER
ECDIS 250V-T TYCS-1 0.6/1kV -DPYCY S-1.5 5A ( SHIP YAR D SUPPLY)
AC100V,1φ,100W
0.6/1kV-D PYCYS-1.5
CONNING 250V-T TYCS-1
DISPLAY
JMA-9100 Instruction Manual

TB4501(OPTION) TB4601(ALA RM) TB4401(EXT RAD AR) N BL -175 0.6/1kV-D PYCYS-1.5 SHIP’S MAINS
1 NA V1TX+ 1 ARPAAL M+ 1 RBVD S TEP- DOWN
T RA NSF OR MER AC220V , 1φ, fo r HEAT ER
>

2 NA V1TX- 2 ARPAAL M- 2 RBVD E

250V-T TYCS-1
3 NA V1RX+ 3 SYSALM + 3 ETIY3

B －39
DGPS
4 NA V1RX- 4 SYSALM + 4 ETIY3E
5 NA V2TX+ 5 PWR AL M+ 5 SVD 1
6 NA V2TX- 6 PWR AL M- 6 SVD 1E
ECHO 250V-T TYCS-1
7 NA V2RX+ 7 ARPAAC K+ 7 ETIY1
SOU NDER 8 NA V2RX- 8 ARPAAC K- 8 ETIY1E
9 LOG RX+ 9 SYSACK+ 9 EXφA1
LOG 250V-T TYCS-1 10 LOG RX- 10 SYSACK- 10 EXφA1E
(NMEA0183) 11 AL MTX+ 11 PWR ACK+ 11 EXφB1
12 AL MTX- 12 PWR ACK- 12 EXφB1E
B.DRAWINGS

13 AL MRX+ 13 EXEVT+ 13 EXφZ1

14 AL MRX- 14 EXEVT- 14 EXφZ1E
>

15 ARPAT X+ 15 AISTX+ 15 SVD 2

16 ARPAT X- 16 AISTX- 16 SVD 2E
RED
17 JAR PA TX+ 17 AIS_TG 17 ETIY2
18 JAR PA TX- 18 AISRX+ 18 ETIY2E
19 NSKT X+ 19 AISRX- 19 EXφA2
20 NSKT X- 20 AIS_RG 20 EXφA2E
WHT
21 HD G RX+ 21 MNTTX + 21 EXφB2
22 HD G RX- 22 MNTTX - 22 EXφB2E
BLK
23 EXφZ2
250V-T TYCS-4 24 EXφZ2E
AIS 25 (NC )
26 (NC )
27 ACKOU T+
LOG 0. 6/1kV-D PYCYS-1.5 28 ACKOU T-
TB4801(L O G)
(200P /NM) 29 WMRST+
1 (N C)
30 WMRST-
2 (N C)

Fig B-35: Terminal Board Connection Diagram of JMA-9132-SA

3 (N C)
250V -M PYCYS-7
GYRO 4 (N C)
5 P1+
T B4701(G YRO) 6 P1-
1 1/R1 7 (N C)
2 2/S1 8 (N C)
3 3/S2 9 S1+
4 S3 10 S2- FILTER AC IN
WHT 0.6/1kV-D PYCY-6
5 5/R2 11 (N C) U SHIP’S MAINS
6 (NC) 12 (N C) W AC100-115V/ AC220-240V 50/60H z 1φ
ALARM MONITORING B LK (S-BAND 30kW RADAR)
V
SYSTEM
( NEAREST AP PRO ACH)
B.7 Terminal Board Connection Diagram

0. 6/1kV-D PYCYS-1.5
JMA-9132-SA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9132-SA

B
 DISPLAY UNIT NCD-4990
14-C OR ES CO MPOSITE CABL E (JRC SU PPL Y)
SCANNER UNIT
B.7.8
RADAR H -2695111153 H-2695110056
(J RC SUPPL Y) CQD-2097 T ERMIN AL BOARD
NKE-1139-1/2
(INTERSWITC H)
TB4101(AN T)
1
1 VD+
2 VD-
2 W iring of PER FOR MANC E MONITOR
T B4201(ISW IN/OU T) 3 TRIG +
1 is com pleted .
1 VDIN 1 4 TRIG - YE L
3 1 U1 TB103 TB104 P81
2 VDIN 1E 5 BP+ GR N GRY P1
BLU 2 V1 1 PTI PTI
3 TRIG IN1 6 BP- PTI
250V-T TYCS-1 4 3 U 2 PTE
4 TRIG IN1E 7 BZ+ BLU PTE PTE
3C-2V x 5 (MAX 30m ) 4 V 3 L VR WHT
VDR YE L T XI WHT
5 BPIN1 8 BZ- R ED B RN TXI
OR N 5 UTH 4 PMS T XE B RN
6 BPIN1E 9 MTR+ ORN TXE
GRN WHT 6 +12v 5 E
JMA-9100 Instruction Manual

7 BZIN1 10 MTR- 4
7 C2 6 TXI
8 BZIN1E 11 MTRE WHT P82
WH T-B LU 8 ΦZE 7 TXE B LU P2
>

9 MTRIN 1+ 12 (NC) L VR B LU
3 L VR
WH T-WH T R ED 9 ΦZ 8 (NC ) R ED R ED
10 MTRIN 1- 13 +48V 1 PMS PMS
B LU 10 ΦA 9 (NC ) B LK B LK
11 MTRIN 1E 14 +48VG E E
ORG 11 E 10 (NC )
12 PWR IN1 PU R
BLK 12 ΦB 11 VER R
13 PWR IN1E 2 BLK
PNK 12 E
14 PWR OU T1
J4407 BR N
15 PWR OU T1E
RJ -45 L AN 2
16 VDOU T1
17 VDOU T1E PERFORMANCE
R ED
18 TRIG OU T1
JMA-9133-SA

19 TRIG OU T1E
B.DRAWINGS

PUR “D” HEATER OPTION MONITOR

CQD-1891 20 BPOU T1
CIRCU IT BREAKER
(J RC SUPPL Y) 21 BPOU T1E
>

WHT 0.6/1kV-D PYCYS-1.5 5A ( SHIP YA RD SUPPLY ) NJU-84

RED 22 BZOUT1
R A C100V,1φ ,100W
23 BZOUT1E
WH T-YE L 0.6/1kV -DPYCYS-1.5
GRN 24 MTROUT 1+
G

5-1 P)
WH T-WH T
BL U 25 MTROUT 1- CBD -1661 ACOU T1
B
26 MTROUT 1E BA TT IN +
GR Y NBL -175 0.6/1kV -DPYCYS-1.5
H BA TT IN -
Y EL STEP -DOWN SHIP’S MAINS
U TRA NSFORME R
B LK GRN AC 220V, 1φ, for H EATER
V

C DC4 2 3-1
9 0 4J4 BUS(D
V
H -2695110006 W
(J RC SUPPL Y)
ECDIS 250V-T TYCS-1
19-CORES COMPOSIT E CA BLE (JR C SUPPL Y)
H-2695110056 HF-20D COAXIAL CABLE
CONNING 250V-T TYCS-1 (JRC SUPPLY)
DISPLAY TB4501(OPTION) TB4601(ALA RM) TB4401(EXT RAD AR)
1 NA V1TX+ 1 ARPAAL M+ 1 RBVD
2 NA V1TX- 2 ARPAAL M- 2 RBVD E
250V-T TYCS-1
3 NA V1RX+ 3 SYSALM + 3 ETIY3

B －40
DGPS
4 NA V1RX- 4 SYSALM + 4 ETIY3E
5 NA V2TX+ 5 PWR AL M+ 5 SVD 1
6 NA V2TX- 6 PWR AL M- 6 SVD 1E
ECHO 250V-T TYCS-1
7 NA V2RX+ 7 ARPAAC K+ 7 ETIY1
SOU NDER 8 NA V2RX- 8 ARPAAC K- 8 ETIY1E TB201 T B203 TB204
1 OR N GR Y
9 LOG RX+ 9 SYSACK+ 9 EXφA1 1 VD + 1 +12V 1 PTI
250V-T TYCS-1 WHT
LOG 10 LOG RX- 10 SYSACK- 10 EXφA1E 2 VD - 2 C2 2 PTE
(NMEA0183) 2 BLU
11 AL MTX+ 11 PWR ACK+ 11 EXφB1 3 TR IG+ 3 ΦZE 3 L VR
3 R ED
12 AL MTX- 12 PWR ACK- 12 EXφB1E 4 TR IG- 4 ΦZ 4 PMS
3 1
13 AL MRX+ 13 EXEVT+ 13 EXφZ1 5 BP+ 5 ΦA 5 E
B.7 Terminal Board Connection Diagram

4
14 AL MRX- 14 EXEVT- 14 EXφZ1E 6 BP-/BZ- 6 E 6 TXI
4 2
15 ARPAT X+ 15 AISTX+ 15 SVD 2 7 BZ+ 7 ΦB 7 TXE
ORN
16 ARPAT X- 16 AISTX- 16 SVD 2E 8 MTR + 8 8 (N C)
RED WHT R ED PUR
17 JAR PA TX+ 17 AIS_TG 17 ETIY2 9 MTR - 9 +48V 9 VERR
BLU BLK
18 JAR PA TX- 18 AISRX+ 18 ETIY2E 10 MTR E 10 +48V G 10 E
19 NSKT X+ 19 AISRX- 19 EXφA2
20 NSKT X- 20 AIS_RG 20 EXφA2E
WHT
21 HD G RX+ 21 MNTTX + 21 EXφB2
22 HD G RX- 22 MNTTX - 22 EXφB2E T B202
BLK YE L
23 EXφZ2 1 U1
GRN
250V-T TYCS-4 24 EXφZ2E 2 V1
AIS 25 (NC ) 3 W1
YE L
26 (NC ) 4 U0
GRN
27 ACKOU T+ 5 V0
LOG 0. 6/1kV-D PYCYS-1.5 28 ACKOU T- 6 W0
TB4801(L O G)
(200P /NM) 29 WMRST+
1 (N C)
30 WMRST-
2 (N C)

Fig B-36: Terminal Board Connection Diagram of JMA-9133-SA

3 (N C)
250V -M PYCYS-7
GYRO 4 (N C)
5 P1+
TRANSCEIVER UNIT NTG-3230
T B4701(G YRO) 6 P1-
1 1/R1 7 (N C)
2 2/S1 8 (N C)
3 3/S2 9 S1+
4 S3 10 S2- FILTER AC IN
WHT 0.6/1kV-D PYCY-6
5 5/R2 11 (N C) U SHIP’S MAINS
6 (NC) 12 (N C) W AC100-115V/ AC220-240V 50/60H z 1φ
ALARM MONITORING B LK (S-BAND 30kW RADAR)
V
SYSTEM
( NEAREST AP PRO ACH)
0. 6/1kV-D PYCYS-1.5
JMA-9133-SA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9133-SA
 JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram

B.7.9 NCD-4990T

DISPLAY UNIT NCD-4990T

MONITOR UNIT
NWZ-170

OPERATION UNIT
NCE-5163
J4406 DSUB -9P J4309
DVI-D
FEMALE

RADAR PROCESS
CIRCUIT
CDC-1324

TERMINAL BOARD
CQD-2097

Option
SUB OPERATION UNIT
Option for X-band 10kW and X-band 25kW-H S.
Used with N KE-2103-6,N KE-2103-6H S and N KE-
NCE-5163
CBD -1661
2254-6H S AC OUT 2
Main
AC/DC POWER SUPPLY
J4311
CONVERTER UNIT CBD-1661
Sub
NBA-5135 J4312

CBD -1684A TB522 TB 402

1 + 1 +
2 ー 2 ー
3 FG 3 FG

CBD -1661
CBD -1684A TB521 AC OUT 1
1 U 1 U
2 V 2 V
3 FG 3 W

RADAR PROCESS UNIT

NDC-1399-9

JMA-9100 Series RADAR

NCD-4990T 卓上型レーダー指示機 ユニット間接続図
INTERCONNECTION DIAGRAM OF DISPLAY UNIT TYPE NCD-4990 T(desktop)

Fig B-37: Inter-Unit Connection Diagram of NCD-4990T

B
B －41
JMA-9100 Instruction Manual > B.DRAWINGS > B.8 GYRO I/F

B.8 GYRO I/F

SERIAL SIGNAL
INDICATOR LED
シリアル信号表示LED

KEEP DEFAULT
設定不要

OPEN
プラグ無し

GYRO INPUT SIGNAL GYRO LOW-VOLTAGE

INDICATOR LED ALERT LED
ジャイロ入力信号LED ジャイロ低電圧警告LED

ERROR INDICATOR LED GYRO SIGNAL PROCESS

エラー表示LED INDICATOR LED
ジャイロ信号処理表示LED

LOG PULSE
INDICATOR LED
ログパルス表示LED

LOW-VOLTAGE GYRO
SETTING
ジャイロ低電圧時に設定

Fig B-38: Parts Location of CMJ-462E

TableB-1： Setting Table of CMJ-462E S1/S2

S1 SETTING 1 2 3 4 5 6 7 8 S2 SETTING 1 2 3 4 5 6 7 8
STEP ON ON
BSHLOG ALM
SYNC OFF OFF
GYRO SETTING
ジャイロ信号

36X ON ON ON
GYRO SIMULATOR
RATIO

90X OFF ON OFF

180X ON OFF ON
LOG SIMULATOR
360X OFF OFF OFF
回転方向 逆／REV ON N.C. (No Connection) OFF
DIRECTION 正／NOR OFF 5 SEC ON
GYRO ALM TIME
シンクロ／SYNC ON 0.2 SEC OFF
パルス／PULSE OFF GYRO SRC HDT ( NMEA (HDT/THS) ) ON
LOG SETTING

未接続／NC OFF (Heading Sensor Source) GYRO OFF

ログ信号

100P／30X ON ON 4800 BPS OFF OFF

パルス 200P／90X OFF ON 9600 BPS ON OFF
NMEA BAUDRATE
PULSE/NM 400P／180X ON OFF 19200 BPS OFF ON
800P／360X OFF OFF 38400 BPS ON ON

B －42
 JMA-9100 Instruction Manual > B.DRAWINGS > B.8 GYRO I/F

TableB-2： Gyro, Log Settings

B
B －43
JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch Unit

B.9 Inter Switch Unit

B.9.1 Terminal Board Connection Diagram

DISPLAY 1 DISPLAY 2
NCD-4990 NCD-4990

TB4201 TB4201
ISW IN/OUT ISW IN/OUT

1
VDIN 1 1 1 VDIN 1

VDIN 1E 2 2 VDIN 1E
BLUE
TRIGIN 1 3 3 TRIGIN 1

TRIGIN 1E 4 4 TRIGIN 1E
YELLOW
BPIN 1 5 5 BPIN 1

BPIN 1E 6 6 BPIN 1E
GREEN
BZIN 1 7 7 BZIN 1
BZIN 1E 8 8 BZIN 1E
WHITE-BLUE
MTRIN 1+ 9 9 MTRIN 1+
WHITE-WHITE
MTRIN 1- 10 10 MTRIN 1-

MTRIN 1E 11 11 MTRIN 1E
ORANGE
PWRIN 1+ 12 12 PWRIN 1+
BLACK
PWRIN 1E 13 13 PWRIN 1E
PINK
PWROUT 1 14 14 PWROUT 1
BROWN
PWROUT 1E 15 15 PWROUT 1E
2
VDOUT 1 16 16 VDOUT 1

VDOUT 1E 17 17 VDOUT 1E
RED
TRIGOUT 1 18 18 TRIGOUT 1

TRIGOUT 1E 19 19 TRIGOUT 1E
PURPLE
BPOUT 1 20 20 BPOUT 1

BPOUT 1E 21 21 BPOUT 1E
CLEAR
BZOUT 1 22 22 BZOUT 1

BZOUT 1E 23 23 BZOUT 1E
WHITE-YELLOW
MTROUT 1+ 24 24 MTROUT 1+
WHITE-WHITE
MTROUT 1- 25 25 MTROUT 1-

MTORUT 1E 26 26 MTORUT 1E
H-2695111153
(JRC SUPPLY )

Fig B-39: Terminal Board Connetion Diagram of NQE-3141-2A

B －44
 DISPLAY1 DISPLAY2 DISPLAY3 DISPLAY4
NCD-4990 NCD-4990 NCD-4990 NCD-4990
TB4201 TB4201 TB4201 TB4201
1 1 1 1
1 VDIN 1 1 VDIN 1 1 VDIN 1 1 VDIN 1
2 VDIN 1E 2 VDIN 1E 2 VDIN 1E 2 VDIN 1E
BLU BLU BLU BLU
3 TRIGIN 1 3 TRIGIN 1 3 TRIGIN 1 3 TRIGIN 1
4 TRIGIN 1E 4 TRIGIN 1E 4 TRIGIN 1E 4 TRIGIN 1E
YEL YEL YEL YEL
5 BPIN 1 5 BPIN 1 5 BPIN 1 5 BPIN 1
6 BPIN 1E 6 BPIN 1E 6 BPIN 1E 6 BPIN 1E
GRN GRN GRN GRN
7 BZIN 1 7 BZIN 1 7 BZIN 1 7 BZIN 1
8 BZIN 1E 8 BZIN 1E 8 BZIN 1E 8 BZIN 1E
WHT-BLU W HT-BLU WHT-BLU WHT-BLU
9 MTRIN 1+ 9 MTRIN 1+ 9 MTRIN 1+ 9 MTRIN 1+
WHT-WHT WHT-WHT WHT-WHT WHT-WHT
10 M TRIN 1- 10 M TRIN 1- 10 MTRIN 1- 10 MTRIN 1-
11 MTRIN 1E 11 MTRIN 1E 11 MTRIN 1E 11 M TRIN 1E
ORG ORG ORG ORG
12 PWRIN 1+ 12 PWRIN 1+ 12 PWRIN 1+ 12 PWRIN 1+
BLK BLK BLK BLK
13 PWRIN 1E 13 PWRIN 1E 13 PW RIN 1E 13 PWRIN 1E
PNK PNK PNK PNK
14 PWROUT 1 14 PWROUT 1 14 PWROUT 1 14 PWROUT 1
BRN BRN BRN BRN
15 PWROUT 1E 15 PWROUT 1E 15 PWROUT 1E 15 PWROUT 1E
2 2 2 2
16 VDOUT 1 16 VDOUT 1 16 VDOUT 1 16 VDOUT 1
17 VDOUT 1E 17 VDOUT 1E 17 VDOUT 1E 17 VDOUT 1E
RED RED RED RED
18 TRIGOUT 1 18 TRIGOUT 1 18 TRIGOUT 1 18 TRIGOUT 1
19 TRIGOUT 1E 19 TRIGOUT 1E 19 TRIGOUT 1E 19 TRIGOUT 1E
PUR PUR PUR PUR
20 BPOUT 1 20 BPOUT 1 20 BPOUT 1 20 BPOUT 1
21 BPOUT 1E 21 BPOUT 1E 21 BPOUT 1E 21 BPOUT 1E
CLR CLR CLR CLR
22 BZOUT 1 22 BZOUT 1 22 BZOUT 1 22 BZOUT 1
23 BZOUT 1E 23 BZOUT 1E 23 BZOUT 1E 23 BZOUT 1E
WHT-YEL WHT-YEL WHT-YEL WHT-YEL
24 M TROUT 1+ 24 MTROUT 1+ 24 MTROUT 1+ 24 MTROUT 1+
WHT-WHT WHT-WHT WHT-WHT WHT-WHT

B －45
25 MTROUT 1- 25 MTROUT 1- 25 MTROUT 1- 25 MTROUT 1-
26 MTORUT 1E 26 MTORUT 1E 26 MTORUT 1E 26 MTORUT 1E
JMA-9100 Instruction Manual

NKE-3141-4
CCL-304R
>

CH-1 CH-2 CH-3 CH-4

TB911 TB912 TB913 TB914 TB915 TB916 TB915 TB916
1 2 1 2 1 2 1 2
1 1 1 1 1 1 1 1
2 2 2 2 2 2 2 2
BLU RED BLU RED BLU RED B LU RED
3 3 3 3 3 3 3 3
B.DRAWINGS

4 4 4 4 4 4 4 4
YEL PUR YEL PUR YEL PUR YEL PUR
>

5 5 5 5 5 5 5 5
6 6 6 6 6 6 6 6
G RN CL R 7 G RN WH T 7 GR N WHT 7 GR N WHT 7
7 7 7 7

Fig B-40: Terminal Board Connection Diagram of NQE-3141-4A

H-2695111153
H-2695111153
H-2695111153
H-2695111153

8 8 8 8 8 8 8 8
WH T-BL U WHT -YEL WH T-BLU WHT-Y EL WH T-BLU W HT-YEL WH T-BLU WHT-Y EL
9 9 9 9 9 9 9 9
WH T-WHT WH T-WHT WH T-WH T WH T-WHT WH T-WH T WH T-WHT WH T-WH T WH T-WHT
10 10 10 10 10 10 10 10
11 11 OR 11 11 11 11 11 11
ORG O RG OR G
12 G 12 12 12
BL K BLK BLK BLK
13 13 13 13
PN K PN K PN K PN K
14 14 14 14

(JRC SUPPLY )
(JRC SUPPLY )
(JRC SUPPLY )
(JRC SUPPLY )

BR N BR N BR N BRN
15 15 15 15
B.9 Inter Switch Unit

B
 B.9.2

J2 P902 H-7ZCRD0972 P903 J903

1 1
-15V -15V
JMA-9100 Instruction Manual

H-7ZCRD0971 J1 CBD-1675 2 2
GND GND
>

1 1 VIN 3 3
GND GND
2 2 +
VIN 4 4 CCL-304
+15V +15V
- 5 5
GND GND
6 6
Terminal board 5V 5V
B.DRAWINGS

J4308 ISW
>

CH-1 CH-2
CH-3 CH-4
CQD-1973 CQD-1973
Interconnection Diagram
B.9 Inter Switch Unit

ＴＢ911
ＴＢ912
ＴＢ913
ＴＢ914
ＴＢ915
ＴＢ916
ＴＢ917
ＴＢ918

B －46
1
J3 J3
1

26
26

Fig B-41: Interconnection Diagram of NQE-3141-2A

H-7ZCRD0970A
H-7ZCRD0970A

1
1

26
26

Terminal board Terminal board

J4306 J4307
(ISW-1CH) (ISW-1CH)
 CBA-357 CN2 P902 H-7ZCRD0920 P903 J903
CB901 1 1
P901 CN1 -15V -15V
H-7ZCRD0919 2 2
LINE LOAD 1 GND GND
AC(L)
A 3 3 3
B GND GND
AC(N) 4 4
C 5 +15V +15V
FG 5 5
C901 C902 C903 D GND GND
6 6
5V 5V
3 4
LF901

E
H -7ZCRD 0921 P904 J904
1
AC
2 (L)
FG
3
1 2 AC CCL-304
TB901 4 (N)
5
U V TE901 TRT
6
AC100V-240V P+
7
TRT
8 P-
9
CD9 E
10
01 PO WLED

B －47
CH-1 CH -2 CH-3 CH-4

TB 911 TB 912 TB 913 TB 914 TB 915 TB 916 TB 917 TB 918

B901 1.V DI N 1.V DOUT
2.V DI NE 2.V DOUTE
P905 J905
3.T RG IN 3.TR GOU T
1 4.T RG INE 4.TR GOU TE
FANV 5.B PIN 5.B POUT
JMA-9100 Instruction Manual

S 2 6.B PIN E 6.B POUTE

FANE
>

7.B ZIN 7.B ZOU T

3 FANP LS 8.B ZIN E 8.B ZOU TE
9.MT RIN + 9.MTR OU T+
10 .MTROU T
10.MTR IN-
-11 .MTROU T
11.MTR INE
E
12.PWR IN
13.RWR INE
14.PWR OU T
15.PWR OU T

Fig B-42: Interconnection Diagram of NQE-3141-4A

P909 J909 E
B.DRAWINGS

R901
1
>

TO TO TO
DISPLAY1 DISPLAY2 DISPLAY3
B.9 Inter Switch Unit

NCD-4990 NCD-4990 NCD-4990

TB4201 TB4201 TB4201

B
JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch Unit

B －48
 Appendix C
Menu Index

Menu Index
C.1 Main ....................................................................................................... C-1
C.2 PI ............................................................................................................ C-5
C.3 TT ........................................................................................................... C-7
C.4 AIS ......................................................................................................... C-8
C.5 AZ .......................................................................................................... C-9
C.6 Track .................................................................................................... C-10
C.7 Route ................................................................................................... C-11
C.8 U.Map .................................................................................................. C-12
C.9 Serviceman Menu ............................................................................... C-14
 JMA-9100 Instruction Manual > C.Menu Index > C.1 Main

C.1 Main

├ 1. EBL Maneuver Setting - - - - - - - - - - - - - - - - - - - - - - - - - section 4.1.5 on page 4-14

│ ├ 1. EBL Maneuver
│ ├ 2. Reach
│ ├ 3. Turn Mode
│ └ 4. Turn Set
├ 2. File Manager - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.11.1 on page 3-120
├ 3. RADAR Menu
│ ├ 1. Process Setting - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.1 on page 3-91
│ │ ├ 1. Video Latitude - - - - - - - - - - - - - - - - - - - - section 3.8.1.1 on page 3-91
│ │ ├ 2. Video Noise Rejection - - - - - - - - - - - - - - - - section 3.8.1.2 on page 3-92
│ │ ├ 3. AUTO Dynamic Range - - - - - - - - - - - - - - - section 3.8.1.3 on page 3-92
│ │ ├ 4. Process Switch - - - - - - - - - - - - - - - - - - - section 3.8.1.4 on page 3-93
│ │ ├ 5. 2nd Process Mode- - - - - - - - - - - - - - - - - - section 3.8.1.5 on page 3-93
│ │ ├ 6. Process Switch Rrange - - - - - - - - - - - - - - - section 3.8.1.6 on page 3-93
│ │ ├ 7. Fast Target Detection - - - - - - - - - - - - - - - - section 3.8.1.7 on page 3-94
│ │ ├ 8. User Function Setting - - - - - - - - - - - - - - - - - section 3.9.3 on page 3-113
│ │ │ ├ 1. Function1 Setting
│ │ │ │ ├ 1. Mode - - - - - - - - - - - - - - - - - - - - - - - - page 3-113
│ │ │ │ ├ 2. IR
│ │ │ │ ├ 3. Process
│ │ │ │ ├ 4. Target Enhance
│ │ │ │ ├ 5. AUTO Sea/Rain
│ │ │ │ ├ 6. Save Present State
│ │ │ │ ├ 9. Next
│ │ │ │ ├ 1. Pulse Length 0.75nm - - - - - - - - - - - - - - - - page 3-115
│ │ │ │ ├ 2. Pulse Length 1.5nm
│ │ │ │ ├ 3. Pulse Length 3/4nm
│ │ │ │ ├ 4. Pulse Length 6/8nm
│ │ │ │ ├ 5. Pulse Length 12nm
│ │ │ │ ├ 6. Pulse Length 16nm
│ │ │ │ ├ 9. Next
│ │ │ │ ├ 1. Video Latitude - - - - - - - - - - - - - - - - - - - - page 3-115
│ │ │ │ ├ 2. Video Noise Rejection
│ │ │ │ ├ 3. AUTO Dynamic Range
│ │ │ │ ├ 4. Process Switch
│ │ │ │ ├ 5. 2nd Process Mode
│ │ │ │ ├ 6. Process Switch Range
│ │ │ │ ├ 7. Fast Target Detection
│ │ │ │ ├ 9. Next
│ │ │ │ ├ 1. Trails Interval - - - - - - - - - - - - - - - - - - - - page 3-115
│ │ │ │ ├ 2. Trails Mode
│ │ │ │ ├ 3. Trails Reference Level
│ │ │ │ ├ 4. Trails Reduction
│ │ │ │ ├ 6. Trails Process
│ │ │ │ ├ 7. Max Interval
│ │ │ │ ├ 9. Next
│ │ │ │ ├ 1. Gain Offset - - - - - - - - - - - - - - - - - - - - - page 3-115
│ │ │ │ ├ 2. PRF
│ │ │ │ ├ 3. Small Buoy Detection
│ │ │ │ ├ 4. Fishnet Detection
│ │ │ │ ├ 5. Antenna Height
│ │ │ │ ├ 8. Set Mode Default
│ │ │ │ └ 9. Initialize
│ │ │ ├ 2. Function2 Setting
│ │ │ ├ 3. Function3 Setting
│ │ │ └ 4. Function4 Setting
│ │ └ 9. SART - - - - - - - - - - - - - - - - - - - - - - - - - - section 6.5 on page 6-12
│ ├ 2. RADAR Trails Setting
│ │ ├ 1. Trails Mode - - - - - - - - - - - - - - - - - - - - - section 3.8.2.1 on page 3-95
│ │ ├ 2. Trails Ref Level - - - - - - - - - - - - - - - - - - - section 3.8.2.2 on page 3-95

C
│ │ ├ 3. Trails Reduction - - - - - - - - - - - - - - - - - - - section 3.8.2.3 on page 3-96
│ │ ├ 5. Trails Process - - - - - - - - - - - - - - - - - - - - section 3.8.2.4 on page 3-96

C －1
JMA-9100 Instruction Manual > C.Menu Index > C.1 Main

│ │ └ 6. Max Interval - - - - - - - - - - - - - - - - - - - - - section 3.8.2.5 on page 3-96

│ └ 3. TXRX Setting
│ │ ├ 1. PRF Fine Tuning - - - - - - - - - - - - - - - - - - section 3.8.3.1 on page 3-97
│ │ ├ 2. Stagger Trigger - - - - - - - - - - - - - - - - - - - section 3.8.3.2 on page 3-97
│ │ ├ 4. PRF - - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.3.3 on page 3-97
│ │ └ 5. Ice Class Standby Mode - - - - - - - - - - - - - - - section 3.8.3.4 on page 3-98
├ 4. Multi Window Setting
│ ├ 1. DIR/DIST EXP Display- - - - - - - - - - - - - - - - - - - - section 3.8.8.1 on page 3-105
│ ├ 2. Numeric NAV INFO - - - - - - - - - - - - - - - - - - - - - section 3.8.8.2 on page 3-105
│ ├ 3. Depth Graph Setting - - - - - - - - - - - - - - - - - - - - - section 3.8.8.3 on page 3-106
│ │ ├ 1. Depth Graph Display
│ │ ├ 2. Depth Range
│ │ ├ 3. Time Range
│ │ └ 4. Depth Unit
│ ├ 4. Wind Graph Setting - - - - - - - - - - - - - - - - - - - - - section 3.8.8.4 on page 3-107
│ │ ├ 1. Wind Graph Display
│ │ └ 2. Wind Speed Unit
│ ├ 5. TEMP Graph Setting- - - - - - - - - - - - - - - - - - - - - section 3.8.8.5 on page 3-108
│ │ ├ 1. TEMP Graph Display
│ │ ├ 2. TEMP Graph Color
│ │ ├ 3. TEMP Range
│ │ │ ├ 1. Temperature setting (MIN)
│ │ │ ├ 2. Temperature setting
│ │ │ ├ 3. Temperature setting
│ │ │ ├ 4. Temperature setting
│ │ │ ├ 5. Temperature setting
│ │ │ └ 6. Temperature setting (MAX)
│ │ └ 4. Time Range
│ └ 6. Course Bar Setting - - - - - - - - - - - - - - - - - - - - - section 3.8.8.6 on page 3-109
│ │ ├ 1. Course Bar Display
│ │ ├ 2. Autopilot Course
│ │ └ 3. ROT Scale
├ 5. Map Setting
│ ├ 3. JRC/ERC Setting
│ │ ├ 1. Day/Night
│ │ ├ 2. Color of Land
│ │ ├ 3. Bright of Land
│ │ ├ 4. Color of Sea
│ │ ├ 5. Bright of Sea
│ │ ├ 6. Color of Name
│ │ ├ 7. Bright of Name
│ │ ├ 8. Bright of Track/Mark/Line
│ │ ├ 9. Next
│ │ ├ 1. LAT/LON Line
│ │ ├ 2. Color of L/L Line
│ │ └ 3. Bright of L/L Line
│ ├ 5. Map Display Setting
│ │ └ 3. LAT/LON Correction
│ └ 7. Map Draw AZI Mode
├ 6. NAV Equipment Setting
│ ├ 1. GYRO Setting - - - - - - - - - - - - - section 3.4.14 on page 3-36, section 7.1.7 on page 7-9
│ ├ 2. MAG Compass Setting - - - - - - - - - - - - - - - - - - - - section 3.4.16 on page 3-37
│ │ ├ 1. Heading Correction
│ │ └ 2. Correct Value
│ └ 3. Set/Drift Setting - - - - - - - - - - - - - - - - - - - - - - - section 3.4.16.1 on page 3-38
│ │ ├ 1. Correction
│ │ ├ 2. Set
│ │ └ 3. Drift
├ 7. Sub Menu
│ ├ 1. Display Color Setting - - - - - - - - - - - - - - - - - - - - section 3.8.5.1 on page 3-99
│ │ ├ 1. Day/Night - - - - - - - - - - - - - - - - - - - - - - section 3.8.5.2 on page 3-100
│ │ ├ 2. Outer PPI
│ │ ├ 3. Inner PPI
│ │ ├ 4. Character
│ │ ├ 5. RADAR Video
│ │ ├ 6. RADAR Trails(Time)
│ │ ├ 8. Target Symbol
│ │ ├ 9. Next
│ │ ├ 1. Cursor
│ │ ├ 2. Range Rings

C －2
 JMA-9100 Instruction Manual > C.Menu Index > C.1 Main

│ │ ├ 3. EBL/VRM/PI
│ │ └ 4. Own Symbol/HL/Vector
│ ├ 2. Brilliance Setting- - - - - - - - - - - - - - - - - - - - - - - section 3.8.5.3 on page 3-100
│ │ ├ 1. RADAR Video - - - - - - - - - - - - - - - - - - - - section 3.8.5.4 on page 3-101
│ │ ├ 2. RADAR Trails
│ │ ├ 3. Target Symbol - - - - - - - - - - - - - - - - - - - - section 3.8.5.5 on page 3-102
│ │ ├ 4. Range Rings
│ │ ├ 5. EBL/VRM/PI
│ │ ├ 6. Character
│ │ ├ 7. Own Symbol/HL/Vector
│ │ └ 8. Keyboard
│ ├ 3. User Setting
│ │ ├ 1. Load User Setting - - - - - - - - - - - - - - - - - - section 3.10.1 on page 3-118
│ │ ├ 2. Save User Setting - - - - - - - - - - - - - - - - - - section 3.10.2 on page 3-119
│ │ └ 3. Delete User Setting - - - - - - - - - - - - - - - - - section 3.10.3 on page 3-119
│ ├ 4. Option Key Setting
│ │ ├ 1. Option1 - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.7 on page 3-103
│ │ └ 2. Option2 - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.7 on page 3-103
│ ├ 5. Buzzer Volume - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.6 on page 3-102
│ │ ├ 1. Key ACK
│ │ ├ 2. OPE Miss
│ │ ├ 3. CPA/TCPA Alarm
│ │ ├ 4. New Target Alarm
│ │ ├ 5. Lost Alarm
│ │ ├ 6. Navigation Alarm
│ │ ├ 7. System Alarm
│ │ └ 8. Inter Switch
│ ├ 6. Date/Time Setting - - - - - - - - - - - - - - - - - - - - - - - section 7.2.7 on page 7-20
│ │ ├ 1. UTC/LMT
│ │ ├ 2. LMT Date
│ │ ├ 3. LMT Time
│ │ ├ 4. Time Zone
│ │ ├ 5. Display Style
│ │ └ 6. Synchronize with GPS
│ ├ 7. Screen Capture Setting
│ │ ├ 1. Select Item
│ │ │ ├ 1. Graphic
│ │ │ ├ 2. RADAR Video
│ │ │ ├ 3. RADAR Trails
│ │ │ └ 4. Map
│ │ ├ 2. Select Card Slot
│ │ ├ 3. File Erase
│ │ ├ 4. AUTO Capture Interval
│ │ └ 5. AUTO File Erase
│ ├ 9. EBL/Cursor Setting - - - - - - - - - - - - - - - - - - - - - - - section 4.1.3 on page 4-3
│ │ ├ 1. EBL1 Bearing Fix
│ │ ├ 2. EBL2 Bearing Fix
│ │ └ 3. Cursor Setting - - - - - - - - - - - - - - - - - - - - - section 4.1.3.3 on page 4-5
│ │ │ ├ 1. EBL/VRM Control CURS
│ │ │ ├ 2. Cursor Length
│ │ │ └ 4. Cursor Pattern
├ 8. Plot Setting
│ └ 6. AUTO Backup - - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.9 on page 3-110
├ 9. Test Menu- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1 on page 8-6
│ ├ 1. Self Test - - - - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.1 on page 8-7
│ │ ├ 1. Memory Test
│ │ │ ├ 1. SDRAM
│ │ │ ├ 2. SRAM
│ │ │ ├ 3. FLASH ROM
│ │ │ └ 4. GRAPHIC
│ │ ├ 2. TXRX Test
│ │ ├ 3. Line Test
│ │ └ 4. Supply Voltage
│ ├ 2. Monitor Test - - - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.2 on page 8-9
│ │ ├ 1. Pattern 1
│ │ ├ 2. Pattern 2
│ │ ├ 3. Pattern 3
│ │ ├ 4. Pattern 4
│
│
│
│
├ 5. Pattern 5
├ 6. Pattern 6
C
C －3
JMA-9100 Instruction Manual > C.Menu Index > C.1 Main

│ │ ├ 7. Pattern 7
│ │ └ 8. Pattern 8
│ ├ 3. Keyboard Test- - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.3 on page 8-9
│ │ ├ 1. Key Test
│ │ ├ 2. Buzzer Test
│ │ └ 3. Light Test
│ ├ 4. MON Display - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.4 on page 8-10
│ ├ 5. System Alarm Log - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.5 on page 8-10
│ └ 6. System Information - - - - - - - - - - - - - - - - - - - - - section 8.3.1.6 on page 8-11
└ 0. EXIT

C －4
 JMA-9100 Instruction Manual > C.Menu Index > C.2 PI

C.2 PI

├ 1. Display for All Lines - - - - - - - - - - - - - - - - - - - - - - - - - - section 4.1.4.3 on page 4-9

├ 2. Operation Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-10
│ ├ All
│ ├ Individual
│ ├ Track
│ └ Equiangular
├ 3. Control1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-11

│ ├ All:All2
│ ├ Individual:Sequential
│ ├ Individual:Index Line 1
│ ├ Individual:Index Line 2
│ ├ Individual:Index Line 3
│ ├ Individual:Index Line 4
│ ├ Individual:Index Line 5
│ ├ Individual:Index Line 6
│ ├ Individual:Index Line 7
│ ├ Individual:Index Line 8
│ ├ Track:Group 1
│ ├ Track:Group 2
│ ├ Track:Group 3
│ ├ Track:Group 4
│ ├ Equiangular:Group 1
│ ├ Equiangular:Group 2
│ ├ Equiangular:Group 3
│ └ Equiangular:Group 4
├ 4. Floating - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-11
├ 5. Heading Link - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -page 4-11
├ 6. Next
├ 8. Press EBL Dial to Control PI#3
├ 9. Press VRM Dial to Move End Point#ii
├ 1. Range Scale Link - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-12
├ 2. Reference Bearingi- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-12

│ ├ All:True4
│ ├ All:HL
│ ├ Individual:True
│ ├ Individual:HL
│ ├ Individual:Index Line 1
│ ├ Individual:Index Line 2
│ ├ Individual:Index Line 3
│ ├ Individual:Index Line 4
│ ├ Individual:Index Line 5
│ ├ Individual:Index Line 6
│ ├ Individual:Index Line 7
│ ├ Individual:Index Line 8
│ ├ Track:True
│ ├ Track:HL
│ ├ Track:Index Line 1
│ ├ Track:Index Line 2
│ ├ Track:Index Line 3
│ ├ Track:Index Line 4
│ ├ Track:Index Line 5
│ ├ Track:Index Line 6
│ ├ Track:Index Line 7
│ └ Track:Index Line 8
├ 3. Operation Area - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-13
├ 4. Display for Individual Line - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-13

1.The setting items are determined by the setting of Operation Mode.

2.Operating Mode : Control
3.Displayed only when "3. Control" is Individual.
4.Operating Mode : Reference Bearing
C
C －5
JMA-9100 Instruction Manual > C.Menu Index > C.2 PI

│ ├ 1. Index Line 1
│ ├ 2. Index Line 2
│ ├ 3. Index Line 3
│ ├ 4. Index Line 4
│ ├ 5. Index Line 5
│ ├ 6. Index Line 6
│ ├ 7. Index Line 7
│ └ 8. Index Line 8
├ 8. Press EBL Dial to Control PI#ii
└ 9. Press VRM Dial to Move End Point#ii

C －6
 JMA-9100 Instruction Manual > C.Menu Index > C.3 TT

C.3 TT
├ 1. Association Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.4 on page 5-37
│ ├ 1. Association
│ ├ 2. Proprity
│ ├ 3. Bearing
│ ├ 4. Range
│ ├ 5. Course
│ ├ 6. Speed
│ └ 7. Applicable AIS Target
├ 2. Target Track Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2 on page 5-44
│ ├ 1. Target Track Function - - - - - - - - - - - - - - - - - - - - section 5.6.2.2 on page 5-44
│ ├ 2. Target Track Color- - - - - - - - - - - - - - - - - - - - - - section 5.6.2.1 on page 5-44
│ │ ├ 1. All
│ │ ├ 2. Target Track No.1
│ │ ├ 3. Target Track No.2
│ │ ├ 4. Target Track No.3
│ │ ├ 5. Target Track No.4
│ │ ├ 6. Target Track No.5
│ │ ├ 7. Target Track No.6
│ │ ├ 8. Target Track No.7
│ │ ├ 9. Next
│ │ ├ 1. Target Track No.8
│ │ ├ 2. Target Track No.9
│ │ ├ 3. Target Track No.10
│ │ └ 4. Other
│ ├ 3. Target Track Display- - - - - - - - - - - - - - - - - - - - - section 5.6.2.4 on page 5-46
│ │ ├ 1. All
│ │ ├ 2. Target Track No.1
│ │ ├ 3. Target Track No.2
│ │ ├ 4. Target Track No.3
│ │ ├ 5. Target Track No.4
│ │ ├ 6. Target Track No.5
│ │ ├ 7. Target Track No.6
│ │ ├ 8. Target Track No.7
│ │ ├ 9. Next
│ │ ├ 1. Target Track No.8
│ │ ├ 2. Target Track No.9
│ │ ├ 3. Target Track No.10
│ │ └ 4. Other
│ ├ 4. Track Memory Interval - - - - - - - - - - - - - - - - - - - - section 5.6.2.5 on page 5-47
│ ├ 5. Clear Track Color - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.6 on page 5-47
│ ├ 6. Clear Track Number
│ └ 7. File Operations - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.7 on page 5-48
│ │ ├ 1. Select Card Slot
│ │ ├ 2. Load Mode
│ │ ├ 3. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
page 5-48
│ │ ├ 4. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
page 5-49
│ │ ├ 5. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
page 5-51
│ │ └ 6. Card T.TRK Display - - - - - - - - - - - - - - - - - - - - - - - - -
page 5-52
├ 3. Trial Maneuver - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.7 on page 5-53
│ ├ 1. Trial Function
│ ├ 2. Course(EBL)
│ ├ 3. Speed(VRM)
│ ├ 4. Vector Time
│ ├ 5. Time to Maneuver
│ └ 6. Own Ship's Dynamic Trait
│ │ ├ 1. Reach
│ │ ├ 3. Turn Radius
│ │ ├ 4. Acceleration
│ │ └ 5. Deceleration
├ 4. Target Number Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.4 on page 5-18
└ 9. TT Test Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7 on page 5-21
│ ├ 1. Test Video- - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.1 on page 5-22
│ ├ 2. TT Simulator - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.2 on page 5-23
│
│
├
└
3.
4.
Status - - - -
Gate Display
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
section
section
5.2.7.3
5.2.7.4
on
on
page
page
5-24
5-25
C
C －7
JMA-9100 Instruction Manual > C.Menu Index > C.4 AIS

C.4 AIS

├ 1. Association Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.4.2 on page 5-37

│ ├ 1. Association
│ ├ 2. Proprity
│ ├ 3. Bearing
│ ├ 4. Range
│ ├ 5. Course
│ ├ 6. Speed
│ └ 7. Applicable AIS Target
├ 2. Target Track Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2 on page 5-44
│ ├ 1. Target Track Function - - - - - - - - - - - - - - - - - - - - section 5.6.2.2 on page 5-44
│ ├ 2. Target Track Color- - - - - - - - - - - - - - - - - - - - - - section 5.6.2.1 on page 5-44
│ │ ├ 1. All
│ │ ├ 2. Target Track No.1
│ │ ├ 3. Target Track No.2
│ │ ├ 4. Target Track No.3
│ │ ├ 5. Target Track No.4
│ │ ├ 6. Target Track No.5
│ │ ├ 7. Target Track No.6
│ │ ├ 8. Target Track No.7
│ │ ├ 9. Next
│ │ ├ 1. Target Track No.8
│ │ ├ 2. Target Track No.9
│ │ ├ 3. Target Track No.10
│ │ └ 4. Other
│ ├ 3. Target Track Display- - - - - - - - - - - - - - - - - - - - - section 5.6.2.4 on page 5-46
│ │ ├ 1. All
│ │ ├ 2. Target Track No.1
│ │ ├ 3. Target Track No.2
│ │ ├ 4. Target Track No.3
│ │ ├ 5. Target Track No.4
│ │ ├ 6. Target Track No.5
│ │ ├ 7. Target Track No.6
│ │ ├ 8. Target Track No.7
│ │ ├ 9. Next
│ │ ├ 1. Target Track No.8
│ │ ├ 2. Target Track No.9
│ │ ├ 3. Target Track No.10
│ │ └ 4. Other
│ ├ 4. Track Memory Interval - - - - - - - - - - - - - - - - - - - - section 5.6.2.5 on page 5-47
│ ├ 5. Clear Track Color - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.6 on page 5-47
│ ├ 6. Clear Track Number
│ └ 7. File Operations - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.7 on page 5-48
│ │ ├ 1. Select Card Slot
│ │ ├ 2. Load Mode
│ │ ├ 3. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
page 5-48
│ │ ├ 4. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
page 5-49
│ │ ├ 5. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
page 5-51
│ │ └ 6. Card T.TRK Display - - - - - - - - - - - - - - - - - - - - - - - - -
page 5-52
├ 3. Trial Maneuver - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.7 on page 5-53
│ ├ 1. Trial Function
│ ├ 2. Course(EBL)
│ ├ 3. Speed(VRM)
│ ├ 4. Vector Time
│ ├ 5. Time to Maneuver
│ └ 6. Own Ship's Dynamic Trait
│ │ ├ 1. Reach
│ │ ├ 2. Turn Radius
│ │ ├ 3. Acceleration
│ │ └ 4. Deceleration
├ 4. AIS Filter Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7 on page 5-32
│ ├ 1. Filter Type - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.2 on page 5-32
│ ├ 2. Make AIS Filter - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.3 on page 5-33

C －8
 JMA-9100 Instruction Manual > C.Menu Index > C.5 AZ

│ ├ 3. Filter Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.4 on page 5-34

│ ├ 4. ENT
│ └ 6. Filter Mode - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.5 on page 5-34
├ 5. Target Number Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.6 on page 5-31
├ 6. AIS Alarm Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.9 on page 5-36
│ ├ 1. Lost Alarm- - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.9.1 on page 5-36
│ └ 2. CPA/TCPA Alarm - - - - - - - - - - - - - - - - - - - - - - section 5.3.9.2 on page 5-36
├ 7. Message - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.5.5 on page 5-29
│ ├ 1. Addressed Message
│ └ 2. Broadcast Message
├ 8. Display Lost TGT Data - - - - - - - - - - - - - - - - - - - - - - - section 5.3.5.6 on page 5-31
└ 9. Own Ship's AIS Data - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.5.7 on page 5-31

C.5 AZ

├ 1. AZ 1- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14

├ 2. AZ 2- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14
├ 3. Make AZ 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14
├ 4. Make AZ 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14
└ 5. ENT

C
C －9
JMA-9100 Instruction Manual > C.Menu Index > C.6 Track

C.6 Track

├ 1. DISP Own Track Color - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.2 on page 3-40

│ ├ 1. All
│ ├ 2. White
│ ├ 3. Cyan
│ ├ 4. Blue
│ ├ 5. Green
│ ├ 6. Yellow
│ ├ 7. Pink
│ └ 8. Red
├ 2. Clear Own Track Color - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.5 on page 3-42
├ 3. Track Type - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.6 on page 3-42
├ 4. Num/Vector Display - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.6 on page 3-42
├ 5. File Operations
│ ├ 1. Select Card Slot
│ ├ 2. Load Mode
│ ├ 3. Load
│ ├ 4. Save
│ ├ 5. Erase
│ └ 6. Card Own Track Display
├ 6. Water Depth Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.7 on page 3-44
│ ├ 1. Depth setting (MIN)
│ ├ 2. Depth setting
│ ├ 3. Depth setting
│ ├ 4. Depth setting
│ ├ 5. Depth setting
│ └ 6. Depth setting (MAX)
├ 7. Water TEMP Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.8 on page 3-45
│ ├ 1. Temperature setting (MIN)
│ ├ 2. Temperature setting
│ ├ 3. Temperature setting
│ ├ 4. Temperature setting
│ ├ 5. Temperature setting
│ └ 6. Temperature setting (MAX)
├ 8. Current Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.9 on page 3-46
│ ├ 1. Current Size
│ ├ 2. Layer A
│ ├ 3. Layer B
│ └ 4. Layer C

C －10
 JMA-9100 Instruction Manual > C.Menu Index > C.7 Route

C.7 Route

├ 1. Select Route - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.1 on page 3-67

├ 2. WPT/Route Settig
│ ├ 1. Waypoint Alarm - - - - - - - - - - - - - - - - - - - - - - - section 3.7.4.1 on page 3-79
│ ├ 2. Route Alarm - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.4.2 on page 3-80
│ ├ 3. Set Route Sequence- - - - - - - - - - - - - - - - - - - - - - section 3.7.2 on page 3-68
│ │ ├ 1. Planned Speed - - - - - - - - - - - - - - - - - - - section 3.7.3.5 on page 3-77
│ │ ├ 2. Add - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.2.2 on page 3-69
│ │ ├ 3. Correct Position - - - - - - - - - - - - - - - - - - - section 3.7.2.3 on page 3-70
│ │ ├ 4. Correct Planned Speed - - - - - - - - - - - - - - - section 3.7.2.4 on page 3-71
│ │ ├ 5. Delete - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.2.5 on page 3-72
│ │ ├ 6. Insert - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.2.6 on page 3-73
│ │ └ 7. New Monitor Route - - - - - - - - - - - - - - - - - section 3.7.2.1 on page 3-68
│ ├ 6. Waypoint Input - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.3 on page 3-75
│ ├ 7. Save Temporary Route
│ ├ 8. Off-Track Limit Line - - - - - - - - - - - - - - - - - - - - - section 3.7.6.1 on page 3-83
│ ├ 9. Next
│ ├ 1. SEL. NUM/Comment Size - - - - - - - - - - - - - - - - - - section 3.7.6.2 on page 3-83
│ ├ 2. Waypoint Vector - - - - - - - - - - - - - - - - - - - - - - - section 3.7.6.3 on page 3-84
│ ├ 3. Status of Origin/DEST - - - - - - - - - - - - - - - - - - - - section 3.7.6.4 on page 3-85
│ └ 4. WPT Number Display - - - - - - - - - - - - - - - - - - - - section 3.7.6.5 on page 3-85
├ 3. WPT/Route Operations - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.5 on page 3-81
│ ├ 1. Route Sequence- - - - - - - - - - - - - - - - - - - - - - - section 3.7.5.1 on page 3-81
│ ├ 2. Waypoint Switch Mode - - - - - - - - - - - - - - - - - - - section 3.7.6.6 on page 3-86
│ ├ 3. Waypoint Skip - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.5.2 on page 3-82
│ ├ 4. Waypoint Back Skip - - - - - - - - - - - - - - - - - - - - - section 3.7.5.2 on page 3-82
│ ├ 5. Set/Cancel Waypoint
│ └ 6. Clear WPT/Route Data
├ 4. File Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8 on page 3-87
│ ├ 1. Select Card Slot - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.1 on page 3-87
│ ├ 2. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.3 on page 3-88
│ ├ 3. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.2 on page 3-87
│ └ 4. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.4 on page 3-89

C
C－ 11
JMA-9100 Instruction Manual > C.Menu Index > C.8 U.Map

C.8 U.Map

├ 1. Own Ship Position - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.1 on page 3-52

├ 2. Edit User Map - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3 on page 3-52
│ ├ 1. Make with Cursor - - - - - - - - - - - - - - - - - - - - - - section 3.6.1.1 on page 3-47
│ │ ├ 1. Type
│ │ └ 2. Color
│ ├ 2. Make with L/L - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.1.3 on page 3-49
│ │ ├ 1. Type
│ │ ├ 2. Color
│ │ ├ 3. L/L
│ │ ├ 4. Comment
│ │ ├ 5. Enter
│ │ └ 9. New Line Input/9.New Mark Input
│ ├ 3. Move - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.2 on page 3-53
│ ├ 4. Delete - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.3 on page 3-55
│ ├ 5. Insert/Move Vertex - - - - - - - - - - - - - - - - - - - - - section 3.6.3.4 on page 3-56
│ ├ 6. Delete Vertex - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.6 on page 3-58
│ └ 7. Delete by Type by Color - - - - - - - - - - - - - - - - - - - section 3.6.3.7 on page 3-59
├ 3. Shift - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.4.1 on page 3-60
├ 4. Shift Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.4.2 on page 3-61
├ 5. Mark Display Setting- - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.2 on page 3-50
│ ├ 1. Display Mark Type- - - - - - - - - - - - - - - - - - - - - - section 3.6.2.1 on page 3-50
│ │ ├ 1. All
│ │ ├ 2. ○
│ │ ├ 3. △
│ │ ├ 4. ▽
│ │ ├ 5. □
│ │ ├ 6. ◇
│ │ ├ 7. Wreck (mark)
│ │ ├ 8. △△
│ │ ├ 9. Next
│ │ ├ 1. ▽▽
│ │ ├ 2. △▽
│ │ ├ 3. ▽△
│ │ ├ 4. ＋
│ │ ├ 5. ×
│ │ ├ 6. Ｙ
│ │ ├ 7. Hand drum (mark)
│ │ ├ 8. Light house (mark)
│ │ ├ 9. Next
│ │ ├ 1. Trapezoid（mark）
│ │ ├ 2. filled Trapezoid（mark）
│ │ ├ 3. Hat(mark)
│ │ ├ 4. ●●
│ │ ├ 5. ●
│ │ ├ 6. Filled Triangle(mark)
│ │ ├ 7. ！
│ │ ├ 8. anchor(mark)
│ │ ├ 9. Next
│ │ ├ 1. slash-anchor(mark)
│ │ ├ 2. circle-dotted line(mark)
│ │ ├ 3. non-dangerous wreck(mark)
│ │ ├ 4. ◎
│ │ ├ 5. mariner's event mark(mark)
│ │ ├ 6. ・
│ │ ├ 7. Wavy line (mark)
│ │ ├ 8. Solid line (mark)
│ │ └ 9. Dashed-dotted line (mark)
│ ├ 2. Display Mark Color - - - - - - - - - - - - - - - - - - - - - section 3.6.2.2 on page 3-51
│ │ ├ 1. All
│ │ ├ 2. White
│ │ ├ 3. Cyan
│ │ ├ 4. Blue

C －12
 JMA-9100 Instruction Manual > C.Menu Index > C.8 U.Map

│ │ ├ 5. Green
│ │ ├ 6. Yellow
│ │ ├ 7. Pink
│ │ └ 8. Red
│ ├ 3. Mark Size - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.2.3 on page 3-51
│ └ 4. Comment Font Size - - - - - - - - - - - - - - - - - - - - - section 3.6.2.4 on page 3-52
├ 6. Geodetic - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.6 on page 3-65
└ 7. File Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5 on page 3-61
│ ├ 1. Select Card Slot
│ ├ 2. Load Mode - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.1 on page 3-61
│ ├ 3. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.1 on page 3-61
│ ├ 4. Unload - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.2 on page 3-62
│ ├ 5. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.3 on page 3-62
│ ├ 6. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.4 on page 3-63
│ └ 7. Card Mark Display - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.5 on page 3-64

C
C －13
JMA-9100 Instruction Manual > C.Menu Index > C.9 Serviceman Menu

C.9 Serviceman Menu

├ Serviceman Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.1 on page 7-1

├ 1. Adjust Menu
│ ├ 1. Tune Adjustment - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.3 on page 7-5
│ ├ 2. Bearing Adjustment - - - - - - - - - - - - - - - - - - - - - - - section 7.1.4 on page 7-7
│ ├ 3. Range Adjustment - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.5 on page 7-7
│ └ 4. TXRX Adjustment
│ │ ├ 1. Antenna Height - - - - - - - - - - - - - - - - - - - - - section 7.1.8 on page 7-9
│ │ ├ 2. Tune Peak Adjustment- - - - - - - - - - - - - - - - - section 7.1.3.1 on page 7-5
│ │ ├ 3. Tune Indicator Adjust - - - - - - - - - - - - - - - - - section 7.1.3.2 on page 7-6
│ │ ├ 4. MON Adjustment - - - - - - - - - - - - - - - - - - section 7.3.4.1 on page 7-31
│ │ ├ 5. MON Indicator Adjustment - - - - - - - - - - - - - - section 7.3.4.2 on page 7-32
│ │ └ 6. Output Pulse - - - - - - - - - - - - - - - - - - - - - section 7.2.4 on page 7-18
├ 2. Installation Menu
│ ├ 1. Installation Information- - - - - - - - - - - - - - - - - - - - - section 7.2.8 on page 7-21
│ │ ├ 1. Date
│ │ ├ 2. Name
│ │ └ 3. Company
│ ├ 2. Master/Slave - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.5.1 on page 7-19
│ ├ 3. Sector Blank- - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2 on page 7-16
│ │ ├ 1. Sector1 - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2.1 on page 7-16
│ │ ├ 2. Sector2 - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2.1 on page 7-16
│ │ ├ 3. Sector3 - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2.1 on page 7-16
│ │ ├ 4. Make Sector1 - - - - - - - - - - - - - - - - - - - - section 7.2.2.2 on page 7-16
│ │ ├ 5. Make Sector2 - - - - - - - - - - - - - - - - - - - - section 7.2.2.2 on page 7-16
│ │ └ 6. Make Sector3 - - - - - - - - - - - - - - - - - - - - section 7.2.2.2 on page 7-16
│ ├ 4. CCRP Setting - - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.9 on page 7-10
│ ├ 5. COM Port Setting - - - - - - - - - - - - - - - - - - - - - - - section 7.2.1 on page 7-12
│ │ ├ 1. Baud Rate - - - - - - - - - - - - - - - - - - - - - - section 7.2.1.1 on page 7-12
│ │ │ ├ 1. COMPASS
│ │ │ ├ 2. MAINTENANCE/LOG
│ │ │ ├ 3. NAV1
│ │ │ ├ 4. NAV2
│ │ │ ├ 5. ALARM
│ │ │ ├ 6. JARPA
│ │ │ ├ 7. AIS
│ │ │ ├ 8. BRIDGE NET
│ │ │ ├ 9. Next
│ │ │ ├ 1. ARPA
│ │ │ └ 2. COM
│ │ ├ 2. RX Port - - - - - - - - - - - - - - - - - - - - - - - section 7.2.1.2 on page 7-13
│ │ │ ├ 1. GPS
│ │ │ ├ 2. DLOG
│ │ │ ├ 3. Alarm
│ │ │ ├ 4. Depth
│ │ │ ├ 5. Temperature
│ │ │ ├ 6. Wind
│ │ │ ├ 7. Current
│ │ │ ├ 8. ROT
│ │ │ ├ 9. Next
│ │ │ └ 1. RSA
│ │ ├ 3. RX Sentence - - - - - - - - - - - - - - - - - - - - section 7.2.1.3 on page 7-14
│ │ │ ├ 1. GPS(LL/COG/SOG)
│ │ │ ├ 2. GPS(WPT/TIME)
│ │ │ ├ 3. Depth
│ │ │ ├ 4. Wind
│ │ │ └ 5. Current
│ │ │ │ ├ 1. Data Set Number
│ │ │ │ ├ 2. Layer A
│ │ │ │ ├ 3. Layer B
│ │ │ │ └ 4. Layer C
│ │ ├ 4. TX Port - - - - - - - - - - - - - - - - - - - - - - - section 7.2.1.4 on page 7-15
│ │ │ ├ 1. TTM(TT)

C －14
 JMA-9100 Instruction Manual > C.Menu Index > C.9 Serviceman Menu

│ │ │ ├ 2. TLL(TT)
│ │ │ ├ 3. TTD(TT)
│ │ │ ├ 4. TLB(TT)
│ │ │ ├ 5. OSD
│ │ │ ├ 6. RSD
│ │ │ ├ 7. ALR
│ │ │ ├ 8. ACK
│ │ │ ├ 9. Next
│ │ │ ├ 1. TTM(AIS)
│ │ │ ├ 2. TLL(AIS)
│ │ │ ├ 3. TTD(AIS)
│ │ │ ├ 4. TLB(AIS)
│ │ │ ├ 5. Remote Maintenance
│ │ │ ├ 6. JRC-ARPA
│ │ │ ├ 7. NMEA0183 Output Format
│ │ │ ├ 8. NMEA0183 Talker
│ │ │ ├ 9. Next
│ │ │ ├ 1. NMEA0183 TX Interval
│ │ │ ├ 2. APB
│ │ │ ├ 3. BOD
│ │ │ ├ 4. GGA
│ │ │ ├ 5. GLL
│ │ │ ├ 6. RMC
│ │ │ ├ 7. RMB
│ │ │ ├ 8. VTG
│ │ │ ├ 9. Next
│ │ │ ├ 1. XTE
│ │ │ ├ 2. BWC
│ │ │ ├ 3. HDT
│ │ │ └ 4. THS
│ │ ├ 7. Line Monitor
│ │ │ ├ 1. COMPASS
│ │ │ ├ 2. MAINTENANCE/LOG
│ │ │ ├ 3. NAV1
│ │ │ ├ 4. NAV2
│ │ │ ├ 5. ALARM
│ │ │ ├ 6. JARPA
│ │ │ ├ 7. AIS
│ │ │ ├ 8. BRIDGE NET
│ │ │ ├ 9. Next
│ │ │ ├ 1. ARPA
│ │ │ ├ 2. COM
│ │ │ ├ 3. TXRX/ISW
│ │ │ ├ 4. KEYBOARD1
│ │ │ └ 5. KEYBOARD2
│ ├ 6. Alarm System - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.9 on page 7-22
│ │ ├ 1. Watch Alarm
│ │ │ ├ 1. Reset Interval - - - - - - - - - - - - - - - - section 7.2.9.1 on page 7-22
│ │ │ └ 2. Trackball Threshold - - - - - - - - - - - - - section 7.2.9.2 on page 7-22
│ │ ├ 2. Relay Output - - - - - - - - - - - - - - - - - - - - section 7.2.9.3 on page 7-23
│ │ │ ├ 1. Relay Output Mode
│ │ │ ├ 2. TT CPA/TCPA
│ │ │ ├ 3. AIS CPA/TCPA
│ │ │ ├ 4. New Target
│ │ │ ├ 5. Lost
│ │ │ └ 6. RADAR Alarm
│ │ ├ 3. ALR Output - - - - - - - - - - - - - - - - - - - - - section 7.2.9.4 on page 7-23
│ │ │ ├ 1. System Alarm
│ │ │ └ 2. TT/AIS Alarm
│ │ ├ 4. Sound Output Mode - - - - - - - - - - - - - - - - - section 7.2.9.6 on page 7-25
│ │ ├ 5. External ACK Setting - - - - - - - - - - - - - - - - section 7.2.9.5 on page 7-24
│ │ │ ├ 1. Critical Alarm
│ │ │ │ ├ 1. Audio
│ │ │ │ ├ 2Indication
│ │ │ │ └ 3. Acknowledge State
│ │ │ ├ 2. Normal Alarm
│ │ │ │ ├ 1. Audio
│ │ │ │ ├ 2. Indication
│
│
│
├
│ │
7. Inter Switch
└ 3. Acknowledge State
C
C －15
JMA-9100 Instruction Manual > C.Menu Index > C.9 Serviceman Menu

│ │ ├ 1. ISW Install
│ │ ├ 2. Mask Setting
│ │ │ ├ 1. No.1 Connection/No.1 Master
│ │ │ ├ 2. No.2 Connection/No.2 Master
│ │ │ ├ 3. No.3 Connection/No.3 Master
│ │ │ ├ 4. No.4 Connection/No.4 Master
│ │ │ ├ 5. No.5 Connection/No.5 Master1
│ │ │ ├ 6. No.6 Connection/No.6 Masteri
│ │ │ ├ 7. No.7 Connection/No.7 Masteri
│ │ │ └ 8. No.8 Connection/No.8 Masteri
│ │ └ 3. S-ISW TXRX Power Supply
│ ├ 8. Language - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.6 on page 7-20
│ ├ 9. Next
│ ├ 1. Input BP Count - - - - - - - - - - - - - - - - - - - - - - - section 7.2.5.2 on page 7-19
│ ├ 2. TNI Blank - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.3 on page 7-17
│ │ ├ 1. TNI Blank - - - - - - - - - - - - - - - - - - - - - - section 7.2.3.1 on page 7-17
│ │ └ 2. Make Sector - - - - - - - - - - - - - - - - - - - - - section 7.2.3.2 on page 7-17
│ ├ 3. Device Installation - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.6 on page 7-8
│ │ ├ 1. Gyro
│ │ ├ 2. Compass
│ │ ├ 3. GPS Compass
│ │ ├ 4. LOG
│ │ ├ 5. 2AXW
│ │ ├ 6. 2AXG
│ │ └ 7. GPS
│ ├ 4. Network
│ │ ├ 1. Network Function
│ │ └ 2. IP Address
├ 3. Maintenance Menu
│ ├ 1. Safety Switch - - - - - - - - - - - - - - - - - - - - - - - - - section 7.4.1 on page 7-33
│ ├ 2. Area Initial - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.4.2 on page 7-34
│ │ └ 1. Partial Master Reset - - - - - - - - - - - - - - - - - section 7.4.2.1 on page 7-34
│ │ │ ├ 1. Serviceman Menu
│ │ │ ├ 2. Except Serviceman Menu
│ │ │ ├ 3. User Setting
│ │ │ ├ 4. TT Setting
│ │ │ ├ 5. AIS Setting
│ │ │ ├ 6. Day/Night
│ │ │ └ 7. JRC Card Copy Record
│ │ └ 2. All Master Reset - - - - - - - - - - - - - - - - - - - section 7.4.2.2 on page 7-34
│ ├ 3. Internal To Card2 - - - - - - - - - - - - - - - - - - - - - - section 7.4.3.1 on page 7-35
│ ├ 4. Card2 To Internal - - - - - - - - - - - - - - - - - - - - - - section 7.4.3.2 on page 7-35
│ ├ 5. TXRX Time - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.4.4 on page 7-36
│ │ ├ 1. Clear TX Time - - - - - - - - - - - - - - - - - - - - section 7.4.4.1 on page 7-36
│ │ ├ 2. Clear Motor Time - - - - - - - - - - - - - - - - - - section 7.4.4.2 on page 7-36
│ │ ├ 3. TXRX to Display Unit - - - - - - - - - - - - - - - - section 7.4.4.3 on page 7-37
│ │ └ 4. Display Unit to TXRX - - - - - - - - - - - - - - - - section 7.4.4.4 on page 7-37
│ └ 6. String Data Update - - - - - - - - - - - - - - - - - - - - - - section 7.4.5 on page 7-38
└ 9. RADAR/TT Initial Setup
│ ├ 1. Signal Processing - - - - - - - - - - - - - - - - - - - - - - - section 7.3.1 on page 7-26
│ │ ├ 1. Echo Noise Level - - - - - - - - - - - - - - - - - - section 7.3.1.1 on page 7-26
│ │ └ 2. Setting Mode - - - - - - - - - - - - - - - - - - - - section 7.3.1.2 on page 7-27
│ ├ 2. TT- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.3.2 on page 7-27
│ │ ├ 1. Vector Constant - - - - - - - - - - - - - - - - - - - section 7.3.2.1 on page 7-27
│ │ ├ 2. Video TD Level - - - - - - - - - - - - - - - - - - - section 7.3.2.2 on page 7-28
│ │ ├ 3. Video High Level
│ │ ├ 4. Video Low Level
│ │ ├ 5. Gate Size
│ │ └ 6. Limit Ring
│ └ 3. MBS- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.3.3 on page 7-29
│ │ ├ 1. MBS Level- - - - - - - - - - - - - - - - - - - - - - section 7.3.3.1 on page 7-29
│ │ └ 2. MBS Area - - - - - - - - - - - - - - - - - - - - - - section 7.3.3.2 on page 7-30

1.Only for ISW Extended Mode

C －16
 JMA-9133-SA
JMA-9132-SA
JMA-9123-7XA/9XA
JMA-9122-6XA/9XA/6XAH
JMA-9110-6XA/6XAH
MARINE RADAR
EQUIPMENT

INSTRUCTION
MANUAL

For further information,contact:

Not use the asbestos

URL http://www.jrc.co.jp
Marine Service Department
Telephone : +81-3-3492-1305
Facsimile : +81-3-3779-1420
e-mail : tmsc@jrc.co.jp
AMSTERDAM Branch
Telephone : +31-20-658-0750
Facsimile : +31-20-658-0755
e-mail : service@jrcams.nl
SEATTLE Branch
Telephone : +1-206-654-5644
Facsimile : +1-206-654-7030
e-mail : service@jrcamerica.com
CODE No.7ZPRD0685 01ETM ISO 9001, ISO 14001 Certified
MAY. 2008 Edition 2 JRC Printed in Japan