Scribd
Upload
27 views2 pages

Electronic Devices Lab Exam Guide

The document outlines the practical examination for the EC3361 Electronic Devices and Circuits Laboratory for B.E/B.Tech students, scheduled for November/December 2022. It includes a list of experiments to be conducted, such as determining characteristics of diodes and transistors, constructing various amplifier circuits, and calculating relevant parameters. Each experiment is assigned a maximum mark of 100, with specific criteria for evaluation.

Uploaded by

suganthi mtech
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
27 views2 pages

Electronic Devices Lab Exam Guide

The document outlines the practical examination for the EC3361 Electronic Devices and Circuits Laboratory for B.E/B.Tech students, scheduled for November/December 2022. It includes a list of experiments to be conducted, such as determining characteristics of diodes and transistors, constructing various amplifier circuits, and calculating relevant parameters. Each experiment is assigned a maximum mark of 100, with specific criteria for evaluation.

Uploaded by

suganthi mtech
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

B.E / B.Tech.

PRACTICAL END SEMESTER EXAMINATIONS, NOVEMBER/DECEMBER 2022

Third Semester
EC3361 – ELECTRONIC DEVICES AND CIRCUITS LABORATORY

(Regulation 2021)

Time : 3 Hours Answer any one Question Max. Marks 100

Aim/Principle/ Tabulation Calculation & Viva- Record Total


Apparatus /Circuit /Program Results Voce
required/Procedure /Drawing
20 30 30 10 10 100

1. Experimentally determine the forward and reverse characteristics of PN junction diode


and Calculate the forward and reverse resistance. ( 100 )

2. Practically construct a circuit to determine the reverse characteristics of Zener diode and
determine the breakdown voltage. ( 100 )

3. Conduct an experiment to determine the line and load regulation of Zener Diode and plot
the characteristics. ( 100 )

4. Conduct an experiment on FWR. Plot the input/output waveforms and calculate the
ripple factor. (100 )

5. Conduct an experiment on FWR with and without capacitor filter. Plot the input/output
waveforms and calculate the ripple factor. ( 100 )

6. Construct a circuit using NPN transistor to experimentally determine the input & output
characteristics of CE configuration and calculate the h-parameter values from the input &
output characteristic curves. (100 )

7. Plot the drain and transfer characteristics of MOSFET by conducting a suitable


experiment. ( 100 )

8. Design and construct a BJT common emitter amplifier using voltage divider bias for the
following specifications : Vcc = 12volts, Ic = 2mA, β = 150.Calculate the gain and plot the
frequency response. (100 )

9. Construct a BJT common base amplifier using voltage divider bias for the following
specifications : Vcc = 12volts, Ic = 2mA, β = 150. Calculate the gain and plot the
frequency response . (100 )

10. Construct a BJT common collector amplifier using voltage divider bias for the following
specifications :. Vcc = 12volts, Ic = 2mA, β = 150. Calculate the gain and plot the
frequency response . (100 )

Page 1 of 1
11. Construct a common source amplifier circuit and calculate gain and plot the frequency
response. (100 )

12. Construct an amplifier circuit to find the difference between two inputs using two
matched transistor and measure its CMRR. (100 )

13. Construct a Cascode amplifier using BJT and measure its gain and plot the frequency
response. (100 )

14. Construct the power amplifier circuit and obtain the corresponding waveform. ( 100 )

15. Construct a BJT emitter follower amplifier using voltage divider bias. Calculate the gain,
bandwidth, gain bandwidth product and plot the frequency response . (100 )

Page 1 of 1

You might also like