Project :- CONSTRUCTION OF E & M WORKSHOP / MT SECTION AT NSCBI AIRPORT

Abstruct sheet
DSR Description
Code No Quoted Quoted
Sl. Total
Unit Rate as per Rate as per Amount in Figure
No Qty.
DSR-2023 Market Rate

Piling Work
A.
20.1 Providing, driving with hydraulic piling rigs with power units and installing
driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified
diameter and length below the pile cap, to carry safe working load not
less than specified, excluding the cost of steel reinforcement but including the
1 cost of shoe and the length of pile to be embedded in the pile cap etc. all
complete. (Length of pile for payment shall be measured from top of shoe
to the bottom of pile cap) :

20.1.3 500 mm dia piles 3189 Rmt 4129.95 ₹ 13,170,410.55

20.6
Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of
loading platform by Kentledge/Anchor piles method and preparation of pile head or
2 construction of test cap and dismantling of test cap after test etc. complete as per
specification & the direction of Engineer in-charge.

(i) 20.6.1
Single pile upto 50 tonne Safe capacity
20.6.1.1
(a) 1 Per Test 54771.5 ₹ 54,771.50
Initial test (Test Load 2.5 times the Safe capacity)
20.6.1.2
(b) 2 Per Test ₹ 39,264.80
Routine test (Test Load 1.5 times the Safe capacity) 19632.4
20.9
Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in
accordance with IS 14893 including surface preparation of pile top by removing soil, mud,
3 dust & chipping lean concrete lumps etc. and use of computerised equipment and high 54 Per Test 1153.2 ₹ 62,272.80
skill trained personal for conducting the test & submission of results, all complete as per
direction of Engineer-in-charge.

B. Earth Work -

2.28 Surface dressing of the ground including removing vegetation and

1 inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m
and lift up to 1.5 m.
(a) 2.28.1 All kinds of Soil 5460 Sqm 34.15 ₹ 186,459.00
 Earth work in excavation by mechanical means (Hydraulic excavator) /
manual means in foundation trenches or drains (not exceeding 1.5 m in width
or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift
2 upto 1.5 m, including getting out the excavated soil and disposal of surplus
excavated soil as directed, within a lead of 50 m.

(a) 2.6.1 All kinds of Soil 2250 Cum 260.3 ₹ 585,675.00

2.6 Extra for every additional lift of 1.5 m or part thereof in excavation / banking
(b)
excavated or stacked materials.
(i) All kinds of Soil 330 Cum 126.8 ₹ 41,844.00
1.1 Carriage of earth, Lime, moorum, building rubbish By Mechanical Transport
3 including loading,unloading and stacking upto 5 km lead 680 Cum 326.68 ₹ 222,142.40

2.25

4 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations 1570 Cum 196 ₹ 307,720.00
etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by
ramming and watering, lead up to 50 and for all lift
2.27 Supplying and filling in plinth with sand under floors, including watering,
5 ramming, consolidating and dressing complete. 1020 Cum 2123.75 ₹ 2,166,225.00

2.34 Supplying chemical emulsion in sealed containers including delivery as

6 specified.
(a) 2.34.1 Chlorpyriphos/Lindane emulsifiable concentrate of 20% 3135 Litre ₹ 735,941.25
234.75
2.35 Diluting and injecting chemical emulsion for Post Construction anti-termite
7 treatment (excluding the cost of chemical emulsion) :
2.35.3 Treatment of soil under existing floors using chemical emulsion @ one litre
per hole, 300 mm apart including drilling 12 mm diameter holes and plugging
(a) with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :

2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1%

(i) 1430 Sqm ₹ 443,371.50
concentration. 310.05

(b) Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite

2.35.2 treatment (excluding the cost of chemical emulsion) :

(i) Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25
litres per linear metre including drilling and plugging holes et
2.35.2.1 270 Rmt ₹ 14,431.50
With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration 53.45
C. Concrete Work -

1 Providing and laying in position cement concrete of specified grade excluding the cost of
centering and shuttering - All work up to plinth level :
4.1.3
1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone
(a) 220.00 Cum 7878.5 ₹ 1,733,270.00
aggregate 20 mm nominal size derived from natural sources)
 4.1.5
(b) 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone 165.0 Cum 7294.7 ₹ 1,203,625.50
aggregate 20 mm nominal size derived from natural sources)
5.33

Providing and laying in position ready mixed or site batched design mix cement concrete
2 for reinforced cement concrete work; using coarse aggregate and fine aggregate derived
from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,
admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of
concrete, to improve durability and workability without impairing strength; including
pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost
of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-
charge, for the following grades of concrete.:
(a) 5.33.1 All works upto plinth leve
(i) 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum 875 Cum 9504.75 ₹ 8,316,656.25
5.33.2 All works above plinth level upto floor V level.
(b)
(i) 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum 620 Cum 9860.4 ₹ 6,113,448.00
3 5.22 STEEL REINFORCEMENT
Steel reinforcement for R.C.C. work including straightening, cutting, bending,
(a)
5.22.6 placing in position and binding all complete upto plinth level.
(i) Thermo-Mechanically Treated bars of grade Fe-500D or more. 130000 Kg 107.85 ₹ 14,020,500.00

(b) Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in
5.22A position and binding all complete above plinth level
(i) 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more 92000 Kg 107.85 ₹ 9,922,200.00
5.9 Centring and shuttering including strutting, propping, etc. and removal of
4 form for the following items of RCC work at all depths and heights complete
as per drawings, specifications and as per direction of Engineer-in-charge.
(a) 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete. 2000 Sqm 392.15 ₹ 784,300.00
Walls (any thickness) including attached pilasters, butteresses, plinth and
(b) string courses etc. 450 Sqm ₹ 379,125.00
5.9.2 842.5
(c) 5.9.3 Suspended floors, roofs, landings, balconies and access platform. 1550 Sqm ₹ 1,437,237.50
927.25
(d) Lintels, beams, plinth beams, girders, bressumers and cantilevers. 1250 Sqm ₹ 920,500.00
5.9.5 736.4
(e) 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. 1350 Sqm ₹ 1,297,755.00
961.3
(f) 5.9.7 Stairs, (excluding landings) except spiral-staircases 230 Sqm ₹ 175,938.50
764.95
(g) 5.9.19 Weather shed, Chajjas, corbels etc., including edges 110 Sqm 951.1 ₹ 104,621.00

D. Waterproofing Treatment
4.1
Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1
1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 Sqm ₹ 8,217.00
12.5 mm nominal size derived from natural sources) 410.85
 Per bag
Extra for providing and mixing water proofing material in cement plaster work in
2 1011 of 60.55 ₹ 61,216.05
proportion recommended by the manufacturers.
cement

Providing and laying integral cement based water proofing treatment including
preparation of surface as required for treatment of roofs, balconies, terraces etc consisting
of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of
cement admixed with water proofing compound conforming to IS. 2645 and approved by
3 Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height
including cleaning the surface before treatment. (b) Laying brick bats with mortar using
broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement :
5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and
approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1
cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645
and approved by Engineer-in-charge to required slope and treating similarly the adjoining
walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two
days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of
cement admixed with water proofing compound conforming to IS : 2645 and approved by
Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of
mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to
IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved
quality in top layer of plaster and finally finishing the surface with trowel with neat cement
slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so
finished shall be flooded with water for a minimum period of two weeks for curing and for
final test.“All above operations to be done in order and as directed and specified by the
Engineer-in-Charge :
22.7.1
(a) With average thickness of 120 mm and minimum thickness at khurra as 65 mm. 470 ₹ 791,762.00
1684.6
22.5

4 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by 125 ₹ 77,131.25
applying cement slurry mixed with water proofing cement compound consisting of
applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing
cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b)
Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement
compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with
water curing for 48 hours. The rate includes preparation of surface, treatment and sealing
of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 617.05
 Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing
treatment to the RCC structures like retaining walls of the basement, water tanks, roof
slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge
5 22.23 deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts
water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for
horizontal surfaces and applying the same from negative (internal) side with the help of
synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-
2010 i.e by reducing permeability of concrete by more than 90% compared with control
concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side.
The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm.
The work shall be carried out all complete as per specification and the direction of the
engineer-incharge. The product performance shall carry guarantee for 10 years against any
leakage.
(a) 22.23.1 For vertical surface two coats @ 0.70 kg per sqm 77 Sqm 472.9 ₹ 36,347.09

(b) 22.23.2 For horizontal surface one coat @1.10 kg per sqm. 40 Sqm 362.8 ₹ 14,380.49
Waterproofing treatment to RCC wall, lift wall, slab at ground floor level,
etc by injecting waterproofing grouting materials of approved
manufacturer with placing & fixing 12 mm dia threaded GI/MS nozzles of
suitable length in a grid pattern at a spacing not exceeding 1.00 m c/c
6 bothways on the entire inside RCC surface and to ensure that the grout should 120 Sqm 153.00 ₹ 18,360.00
flow through all the surface have been sealed. The work should also
include for sealing of the nozzles after the injection operation is over with
quick setting compound admixture with cement all complete as per
direction with all labour & materials.

7 22.14 Grading roof for water proofing treatment with

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

(a) 34 cum ₹ 269,516.59
nominal size) 75mm thkickness
22.14.1 8042.3

(b) Cement mortar 1:3 (1 cement : 3 coarse sand) 10 cum 16112.1 ₹ 163,872.82
22.14.2
 Providing and applying of swellable type water stop tape, 19 mm x 25 mm thick in linear
8 22.26 metre (expansive nature) for construction joints treatment of RCC structure such as raft 65 Rmt 573.45 ₹ 37,331.60
slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining
walls etc.. After cleaning the surface, one coat of required primer for swellable water stop
tape shall be applied throughout the length of the joint @3.78 litre per 240 running metre.
Over the primed surface swellable type water stop tape shall be placed. The work shall be
carried out all complete as per specification and the direction of the Engineer-In-Charge.
The product performance shall carry guarantee for 10 years against any leakage

E. Brick Work
6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class
1 designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse 110 Cum ₹ 810,771.50
sand)
7370.65
6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 in superstructure above plinth level up to floor V level in all shapes and
2 sizes in : 610 Cum ₹ 5,700,053.50
Cement mortar 1:4 (1 cement : 4 coarse sand)
9344.35
6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class
3 designation 7.5 in superstructure above plinth level up to floor V level. 1170 Sqm ₹ 1,314,846.00
Cement mortar 1:4 (1 cement :4 coarse sand)
1123.8
6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third
4 course of half brick masonry. 1170 Sqm ₹ 122,616.00
104.8
F. Plaster work
13.16 6mm cement plaster of mix for celling: (a) 1:3 (1 cement : 3 fine sand) ₹ 294,441.00
1 980 Sqm 300.45
13.4 12 mm thick cement plaster with cement mortar 1:6 (1 cement: 6 coarse sand)
on internal surfaces of walls (brick or concrete surfaces) finished smooth with
2 3850 Sqm ₹ 1,323,052.50
trowel including scafolding, curing etc., complete at all heights : (Internal finishing
side) 343.65
13.12 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1
3 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 4400 Sqm ₹ 2,364,780.00
3 coarse sand) finished rough with sponge. 537.45
4 20 mm cement plaster
13.6 767 Sqm ₹ 373,835.80
1:4 (1 cement: 4 coarse sand) 487.4
5 13.18 Neat cement punning 767 Sqm 79.95 ₹ 61,321.65

G. PAINT
 13.8
Providing and applying white cement based putty of average thickness 1 mm, of approved
1 brand and manufacturer, over the plastered wall surface to prepare the surface even and 5350 Sqm ₹ 834,867.50
smooth complete. 156.05
2 Sonosent Cement paint
2 coat 6426 Sqm 70.00 ₹ 449,820.00

3 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as
per manufacturers specifications :
193.7
(a) Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of 5350 Sqm ₹ 1,036,295.00
Special primer applied @ 0.75 ltr /10 sqm 193.7

4
Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted)
having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal
resistance, dirt resistance exterior paint of required shade with silicon additives
13.48A
(a) New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of 4400 Sqm ₹ 797,500.00
exterior primer applied @ 2.20 kg/10 sqm) 181.25
13.62 Painting with synthetic enamel paint of approved brand and manufacture to give an
5 even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint 250 Sqm ₹ 56,550.00
13.62.1 of approved brand and manufacture 226.2
13.52
6 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per
Sqm
manufacturer's specifications including appropriate priming coat, preparation of surface,
etc. complete.
(a) 13.52.1 On steel work 2130 241.75 ₹ 514,927.50
7 13.68 French spirit polishing :
(a) Two or more coats on new works including a coat of wood filler 90 Sqm 446.25 ₹ 40,162.50
13.68.1

8 13.5 Applying priming coat :

With ready mixed red oxide zinc chromate primer of approved brand and
(a) 2130 Sqm ₹ 143,562.00
13.50.3 manufacture on steel galvanised iron/steel works 67.4
13.85 With ready mixed pink or Grey primer of approved brand and manufacture on
(b) wood work (hard and soft wood) Sqm ₹ 7,738.50
110 70.35

(c) 13.85.1 Applying one coat of water thinnable cement primer of approved brand and manufacture
on wall surface :
(i) 13.85.3 Water thinnable cement primer 280 Sqm ₹ 20,706.00
73.95

H. Tiles & Granite

 Providing and laying Vitrified tiles in different sizes (thickness to be specified
by manufacturer), with water absorption less than 0.08 % and conforming to I.S.
15622, of approved make, in all colours & shade, in skirting, riser of steps, over
1 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with
grey cement slurry @
3.3 kg/ sqm including grouting the joint with white cement
& matching pigments etc. complete.

(a) 11.38 Size of Tile 600x600 mm 940 Sqm ₹ 1,525,667.00

1623.05
Providing and laying Ceramic glazed floor tiles of size
300x300 mm (thickness to be specified by the manufacturer), of 1st
quality conforming to IS : 15622, of approved make, in all colours, shades, except
2 White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4
(1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m
including pointing the joints with white cement and matching pigments etc.,
complete.

(a) 11.46 300x300mm Size. 82 Sqm 1315.3 ₹ 107,854.60

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness
3 to be specified by the manufacturer), of approved make, in all colours, shades except
burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting,
risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse
sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white
cement mixed with pigment of matching shade complete
8.31
(a) Toilet Wall Tiles (300X600)mm 295 Sqm 1267.95 ₹ 374,045.25
4 100 thk VDF Flooring with Concrete grade M30 640 Sqm 1,100.00 ₹ 704,000.00
11.6 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement :
5 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick 32 Sqm ₹ 21,185.60
662.05
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded
and prepolished, machine cut for kitchen platforms, vanity counters, window
sills , facias and similar locations of required size, approved shade, colour and texture
laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints
6
treated with white cement, mixed with matching pigment, epoxy touch ups, including
rubbing, curing, moulding and polishing to edges to give high gloss finish etc.
complete at all levels.

(a) Granite stone slab of all colour and texture except black, Cherry/Ruby red
(i) 8.2.3 Area of slab upto 0.50 sqm 25 Sqm ₹ 104,267.50
4170.7
7 Providing and laying Polished Granite stone flooring in required design and patterns, in
linear as well as curvilinear portions of the building all complete as per the architectural
drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar
1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white
cement slurry admixed with pigment of matching shade including rubbing , curing and
polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
(a) 11.56 Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent 360 Sqm 4481.3 ₹ 1,613,268.00
8.3
(b) Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including 270 Rmt ₹ 137,956.50
machine polishing to edge to give high gloss finish etc. complete as per design approved by
Engineer-in-Charge. 510.95
8.2

8 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and
prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and
similar locations of required size, approved shade, colour and texture laid over 20 mm
thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,
mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and
polishing to edges to give high gloss finish etc. complete at all levels
(a) 8.2.2
Granite stone slab colour black, Cherry/Ruby red
Area of slab over 0.50 sqm 46 Sqm 5136.3 ₹ 236,269.80

9 Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1
cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white
cement complete
8mm thick
8.9 Granite of any colour and shade 21 Sqm 3617.55 ₹ 75,968.55

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI
(solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on
waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the
10 ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement &
marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts
complete, including providing skirting upto 150 mm height along the parapet walls in the
same manner.

12.55 390 Sqm ₹ 664,540.50

(300x300)mm 1703.95

11 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey
cement slurry mixed with pigment to match the shade of the slab, including rubbing and
polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
11.26 25 mm thick 130 Sqm 1948.25 ₹ 253,272.50
 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed
12 with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing
and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse
sand)
11.2 Dark shade pigment using ordinary cement 170 Sqm 1119.5 ₹ 190,315.00
8.5
Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen
13 platform, vanity counter and similar location in marble/ Granite/ stone work, including 15 Each ₹ 14,680.50
necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges
etc. complete 978.7

I. Fire
9.161

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35
1 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc 14.8 Metre 2202.9 32,514.80
coating not less than 120gm/sqm) suitable for mounting 120 minutes Fire Rated Glazed
Door Shutters. The frame shall be filled with mineral wool Insulation having density
minimum 96Kg/cum. The frame will have a provision of G.I. anchor fastners 14 nos (5 each
on vertical style & 4 on horizontal style of size M10 x 80) suitable for fixing in the opening
along with factory made template for SS ball bearing hinges of Size 100x89x3mm for fixing
of fire rated glazed shutter. The frame shall be finished with a approved fire resistant
primer or powder coating of not less than 30 micron in desired shade as per the directions
of Engineer - in- Charge. (Cost of SS ball bearing hinges is excluded)
9.162

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minutes fire
rating conforming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per 12017.9
2 16 Sqm ₹192,286.40
laboratory approved by Engineer-in-Charge, with suitable mounting on door frame,
consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110
mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/sqm)
duly filled mineral wool insulation having density minimum 96 kg/cum and fixing with
necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make,
including applying a coat of approved fire resistant primer or powder coating not less than
30 micron etc all complete as per direction of Engineer-in-Charge (panelling to be paid for
seperately).
 9.163

Providing and fixing non load bearing fixed frame for fire resistant glazed partition for 120
minutes fire rating, made out to a profile of dimension 60mm x 70 mm of 1.6 mm thick
galvanised steel sheet as per test evidence suitable for fixing fire rated glass for 120
minutes of both integrity & radiation control (EW120) & minimum 20 minutes of insulation
(EI20).The profile has to be fixed to the supporting construction by means of anchor
3 fasteners of size M10 x 80, every 150 mm from the edges and every 500 mm (approx) c/c. 10 Metre 22,029.00
Linear measurement of frame shall be measured for payment. The frame shall be filled
with mineral wool insulation of density minimum 96kg/ cum. and finished with a approved
fire resistant primer or powder coating of not less than 30 micron in desired shade as per
NBC 2016, IS 16231 (Part 3):2016 and directions of Engineer - in- Charge.

2202.9
9.138

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc.,
with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120
gm/sqm) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from
the edges and 150 mm c/c , including applying a coat of approved fire resistant
primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape
of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and
as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of
4 fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of 14 Sqm 565,677.70
insulation (EI20). The manufacturer have to give test report/certification of fire glass and
the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested
in approved NABL accredited lab or by any other accreditation body which operates in
accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for
testing and calibration scopes shall be eligible. The maximum glazing size
shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

40405.55
9.139 Providing and fixing panic bar / latch (Double point) fitted with a 50,196.90
singlebody, Trim Latch & Lock on back side of the Panic Latch of
5 reputed brand and manufacture to be approved by the Engineer- in- 6 Each
charge, all
complete. 8366.15
J. Aluminium Window
 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions
with extruded built up standard tubular sections / appropriate Z sections and other
sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs
and screws or with fixing clips, or with expansion hold fasteners including
necessary filling up of gaps at junctions, at top, bottom and sides with required
PVC/neoprene gaskit etc. Aluminium sections shall be smooth, rust free, straight,
1
mitred and jointed mechanically wherever required including cleat angle, Aluminium
snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete
as per architectural drawings and the directions of Engineer-in-charge. (Glazing and
paneling to be paid for separately) :

(a) 21.1.1
For fixed portion
21.1.1.2
(i) 440 Kg ₹ 233,596.00
Powder coated
For shutters aluminium
of doors, (minimum
windows thickness
& ventilators of powder
including coatingand
providing 50 fixing
micron)
hinges/ pivots 530.9
21.1.2 and making provision for fixing of fittings wherever required including the cost of EPDM
(b)
rubber / neoprene gasket required (Fittings shall be paid for separately)
21.1.2.2
660 Kg ₹ 418,737.00
Powder coated aluminium (minimum thickness of powder coating 50 micron) 634.45
21.3
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions
2 etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings
and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in
basic item):

(a) 135 Sqm ₹ 203,208.75

With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 1505.25
K. Door

1 Providing wood work in frames of doors, windows, clerestory windows and other frames,
wrought framed and fixed in position with hold fast lugs or with dash fasteners of required
dia & length (hold fast lugs or dash fastener shall be paid for separately).
9.1.2 Sal wood 2.5 Cum 116520.3 ₹ 291,300.75

2
9.40 Providing and fixing wooden moulded beading to door and window frames with iron
screws, plugs and priming coat on unexposed surface etc. complete :
2nd class teak wood
9.40.1 310 Rmt ₹ 68,541.00
50x12 mm 221.1

3 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with
stainless steel screws etc. complete :
9.71.1 200 Each ₹ 25,970.00
125x64x2.50 mm 129.85
 4 Providing and fixing panelled or panelled and glazed shutters for doors, windows and
clerestory windows, fixing with butt hinges of required size with necessary screws,
excluding panelling which will be paid for separately, all complete as per direction of
Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)
Second class teak wood
9.5.1 35 mm thick shutters 112 Sqm 4111.95 ₹ 460,538.40
wood
grain in gloss / matt/ suede finish with high density protective surface
5 layer
and reverse side of adhesive bonding quality conforming to IS : 2046
Type S,
9.127 1.0 mm thick 230 Sqm 897.3 ₹ 206,379.00

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm
6 diameter bolts, nuts and wooden plugs and embedding in cement concrete block
300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm
nominal size).
9.53 129 Each 228.85 ₹ 29,521.65
SS 304 square tower bolt with 25mm projection and Dia 10mm bolt.
7 L=150mm in Satin Finish. Complete set including the fixing
accessories.
250x10 mm 52 Each 148.00 ₹ 7,696.00

SS304 6 lever mortise lock with Door Handle set, Lock Body 2C
( Both Side Key).Corrosion resistance (Salt spray test ) for more
than 96 Hrs, Handle life cycle test more than 50000 times, Cylinder
8 life cycle test more than 75000 times, Lock life cycle test more
-
than 100000
.One turn of the key from outside or inside throws the Dead bolt
out by 10 mm. A further
one turn throws the bolt by another 10 mm.
45 Each 1,557.00 ₹ 70,065.00

9 Providing and fixing aluminium extruded section body tubular type universal hydraulic
door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto
36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment
with necessary accessories and screws etc. complete.
9.84 53 Each 983.15 ₹ 52,106.95
SS304 Twin rubber Door Stopper in Satin Steel finish with 95mm
10 length, 7mm Dia and rubber base. Positive stop at fixed angles.
Complete set including the fixing accessories.
53 Each 108.00 ₹ 5,724.00
Supply, fitting, and fixing stainless steel (304 grade) door
11 hardware fittings including necessary stainless steel screws, glues,
and all labour etc for the following items…

25 mm dia 600 mm long SS304 pair of H/D type pull handle. 53 Each 1,350.00 ₹ 71,550.00
 Wall mounted PVC door bufferin white finished with 32 mm dia and 70 mm
12
length, complet set including the fixing accessories.
53 Each 414.00 ₹ 21,942.00
13 Rail shutter at Work shop area 145 Sqm 12,500.00 ₹ 1,812,500.00

Providing and fixing factory made door frame (single rebate) made out of solid foam PVC extruded
14 9.123 profile of minimum 60 mm width and minimum 30 mm thickness, having homogenous fine cellular 45 Rmt 696 ₹ 31,320.00
structure and integral smooth outer skin. The frame’s vertical and horizontal members to be
mitered cut and joined together with PVC solvent adhesive / cement and both corners strengthened
with fully threaded steel screws (of required size) fixed diagonally. The door frame is to be fixed to
door jambs using 6 Nos. SS 304 grade minimum 8 mm dia CSK Phillips stainless steel self tapping
screws/fasteners with PA6 grade polyamide sleeves both of required size, and gap if any between
the door frame and the jamb must be filled with clear silicon, complete as per direction of the
Engineer-in-Charge

Providing and fixing factory made PVC door shutter made of solid foam PVC profiles of thikness 5
mm and 15 mm at edges integrally extruded for vertical style and horizontal (top/ bottom/ lock)
rails of minimum cross section of 70mmx 28mm, of shape and design as per manufacturer’s
15 9.124 specifications having homogenous fine cellular structure and smooth integral outer skin, inserted
with G.I. ‘C’ section/ rectangular tube profile of minimum 0.30 mm thickness with 120 gsm coating
as stiffeners as per manufacturer’s specifications Mitred cut joints for styles and rails provided with
telescopic polymeric ‘L’ corners are jointed together using solvent adhesive and strenghtened with
fully threaded stainless steel screws (of required size) through reinforced stiffener with paneling of
specified solid foam PVC board/ high pressure laminate of required thickness and of approved
design and shade (matching the styles and rails), secured within styles and rails with specially
designed solid foam PVC moulded beadings of required size using PVC solvent adhesive/ cement.
The finished door shutter including SS hardware, 1 no. ss sliding bolt 200 x 10mm, 1 no. SS tower
bolt 200 x 10 mm and 2 nos. SS handles 125mm, shall be fixed to frame with 3 nos. stainless steel
hinges of minimum size 100x58x1.9 mm and stainless steel screws of required size complete as per
direction of the Engineer-in-Charge. (Cost of above hardware is inclusive in rates)

(a) 9.124.1 5 mm thick solid foam PVC panel of required size with moulded/ extruded beading of 15 Sqm 3754.2 ₹ 56,313.00
appropriate design shape and size as per manufacturer’s specifications ( to secure the
panel insert tight in place within the style and rails of shutter) matching the colour and
shade of shutter frame. Non decorative type.

L. SS Railling
 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,
channels, plates etc., including welding, grinding, buffing, polishing and making
curvature (wherever required) and fitting the same with necessary stainless steel
nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless
1 steel dash fasteners , stainless steel bolts etc., of required size, on the top of the 850 Kg 772.4 ₹ 656,540.00
floor or the side of waist slab with suitable arrangement as per approval of Engineer-
incharge, (for payment purpose only weight of stainless steel members shall be
considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

2 Ornamental Grill with squire bar or flat patti

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in
(a) position and applying a priming coat of approved steel primer using structural steel etc. as
required.
10.25.2
(i) 300 Kg ₹ 51,780.00
In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 172.6

M. Sanitary
17.81

1 Providing and fixing floor mounted, white vitreous china single piece, double traps
syphonic water closet of approved brand/make, shape, size and pattern including
integrated white vitreous china cistern of capacity 10 litres with dual flushing system,
including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc
including making connection with the existing P/S trap, complete in all respect as per
directions of Engineer-in-Charge.
4 Each 18212.9 ₹ 72,851.60
17.4

2 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal
basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing
cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps
complete, including painting of fittings and brackets, cutting and making good the walls
and floors wherever required :
17.4.1 4 Each ₹ 25,035.00
One urinal basin with 5 litre white P.V.C. automatic flushing cister 6258.75
17.7
3 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P.
brass waste of standard pattern, including painting of fittings and brackets, cutting and
making good the walls wherever require:
17.7.1
White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar 10 each ₹ 26,488.50
taps 2648.85
17.16A
4 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. 4 ₹ 1,396.60
triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - each
charge. 349.15
 17.1

5 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I.
brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting
and making good the walls wherever required :
17.10.1 Kitchen sink with drain board
17.10.1.1 510x1040 mm bowl depth 250 mm 2 each 6945.6 ₹ 13,891.20
6 17.34.1 Providing and fixing toilet paper holder : C.P. brass 4 each 803.7 ₹ 3,214.80
17.31
7 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved 10 ₹ 16,079.50
each
quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P.
brass screws and washers complete. 1607.95
8 17.7 Providing and fixing PTMT Bottle Trap for Wash basin and sink
17.70.1
Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe
260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum 10 each ₹ 3,671.00
water seal, weighing not less than 260 gms 367.1
Providing,Fixing, testing and commissioning Shower set brass CP
9 (Hot and Cold) complete exposed type driverter,Brass CP 15
mm overhead shower arm with 100 mm dia rose.
4 each 3783 ₹ 15,132.00
17.22B
10 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as
approved by Engineer in charge.
15 mm nominal dia 4 each 6940.75 ₹ 27,763.00
18.52
11 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved
make conforming to IS:8931.
18.52.1 15 mm nominal bore 16 each 670.45 ₹ 10,727.20
18.5
12 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS
standards and weighing not less than 810 gms.
18.50.1 15 mm nominal bore 12 each 820.7 ₹ 9,848.40
18.53
13 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved
quality conforming to IS:8931
18.53.1 15 mm nominal bore 4 each 574.3 ₹ 2,297.20
17.69
14 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and
colour. 17.69.1 Waste coupling 31 mm
17.69.2
Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 12 each ₹ 1,468.80
gms 122.4
17.71

15 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm 8 each ₹ 1,346.80
distance from wall of standard shape with bracket of the same materials with snap fittings
of approved quality and colour, weighing not less than 105 gms 168.35
17.72

16 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with 8 each ₹ 1,855.60
minimum distances of 37 mm from wall face with concealed fittings arrangement of
approved quality and colour, weighing not less than 88 gms 231.95
 17.73
17
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with
CP brass screws with concealed fittings arrangement of approved quality and colour.
17.73.2
600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 4 each ₹ 2,835.80
88 mm, weighing not less than 190 gms. 708.95
17.33

18 Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on 4 each ₹ 4,334.00
anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed
with 40 mm long screws, rawl plugs etc., complete. 1083.5
17.75
19 Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP 4 each ₹ 428.80
thread and shapes, weighing not less than 60 gms. 107.2
20 17.76 Providing and fixing PTMT urinal cock of approved quality and colour.
17.76.1
15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads 4 each ₹ 701.60
weighing not less than 48 gms 175.4
17.74
21 Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of 4 each ₹ 2,852.80
approved quality and colour, weighing not less than 300 gms. 713.2
22 Providing and fixing 100 mm sand cast Iron grating for gully trap
17.29 15 each 53.25 ₹ 798.75
18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal
stability for hot & cold water supply, including all CPVC plain & brass threaded
fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing
of pipes & fittings with one step CPVC solvent cement and the cost of cutting
23
chases and making good the same including testing of joints complete as per
direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc.

(a) 18.8.1 15 mm nominal outer dia Pipes 55 Metre 497.8 ₹ 27,379.00

(b) 18.8.2 20 mm nominal outer dia Pipes 37 Metre 537.6 ₹ 19,891.20
18.9

24 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply including all CPVC plain & brass threaded fittings This includes
jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing
of joints complete as per direction of Engineer in Charge.
(a) External work
(b) 20 mm nominal dia Pipes 27 Rmt 274.3 ₹ 7,406.10
(c) 25 mm nominal dia Pipes 47 Rmt 355.4 ₹ 16,703.80
(d) 32 mm nominal dia Pipes 36 Rmt 438.6 ₹ 15,789.60
(e) 40 mm nominal dia Pipes 73 Rmt 563.05 ₹ 41,102.65
(f) 50 mm nominal dia Pipes 130 Rmt 794.25 ₹ 103,252.50
(g) 80 mm nominal dia Pipes 180 Rmt 2166.35 ₹ 389,943.00
 Providing and fixing on wall face unplasticised - PVC moulded fittings/
accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592
25
Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm
gap for thermal expansion.
150mm 155 Rmt 1099 ₹ 170,345.00
Providing and fixing on wall face unplasticised Rigid PVC SWR pipes conforming
to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382,
26
leaving 10 mm gap for thermal expansion,
(i) Single socketed pipes.
110 mm diameter 140 Rmt 400 ₹ 56,000.00

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste
27
fittings complete.:Semi rigid pipe
17.28.1.1 32 mm dia 16 Rmt 103.9 ₹ 1,662.40
28 Flexible pipe
17.28.2.1 32 mm dia 15 Rmt 119.55 ₹ 1,793.25
17.28.2.2 40 mm dia 15 Rmt 119.55 ₹ 1,793.25
18.10
29 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making
good the walls etc. Internal work - Exposed on wall
nternal work - Exposed on wall
(a) 15 mm dia nominal bore 27 Rmt 366.4 ₹ 9,892.80
(b) 20 mm dia nominal bore 23 Rmt 437.3 ₹ 10,057.90
18.12
30 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling
etc. External work
(a) 15 mm dia nominal bore 30 Rmt 322.15 ₹ 9,664.50
(b) 20 mm dia nominal bore 35 Rmt 368.6 ₹ 12,901.00
(c) 80 mm dia nominal bore 42 Rmt 1041.7 ₹ 43,751.40

N Structureal Steel work

10.2 Structural steel work riveted, bolted or welded in built up sections,
1 trusses and framed work, including cutting, hoisting, fixing in position kgs ₹ 7,487,200.00
56000
and applying a priming coat of approved steel primer all
complete. 133.7
2 Foundation bolt 310 kgs 160.00 ₹ 49,600.00

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as
per IS:10910 on 12 mm dia steel bar conforming to IS:1786 having minimum cross
section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm
with minimum 112 mm space between protruded legs having 2 mm tread on top
surface by ribbing or chequering besides necessary and adequate anchoring projections on
3 tail length on 138 mm as per standard drawing and suitable to with stand the bend test and 10 Each 345.00 ₹ 3,450.00
chemical resistance test as per specifications and having manufacture’s permanent
identification mark to be visible even after fixing, including fixing in manholes with 30 x 20 x 15 cm
cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size) complete as per design.
O. Miscellaneous Work
Supplying and laying Polythene Sheet (150gm/Sqm) over damp
1 proof course or below flooring or roof terracing or in foundation or in 2100 Sqm 30.00 ₹ 63,000.00
foundation trenches
12.1/12.1.
2
Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with
polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet
washers or with G.I. limpet washers filled with white lead, including a coat of approved
2 950 Sqm ₹ 1,194,672.50
steel primer and two coats of approved paint on overlapping of sheets complete (up to any
pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and
trusses and including cutting to size and shape wherever required.

1257.55

3 Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with
iron brackets 40x3 mm size, bolts, nuts and washers etc., including making necessary
12.7 connections with rain water pipes complete
0.80 mm thick with zinc coating not less than 275 gm/m² 70 Rmt 1029.65 ₹ 72,075.50
12.7.1
10.18

4 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of 45 Each ₹ 9,929.25
internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface
hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by
means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made
of 12 mm dia M.S. bar bent to shape as per standard drawing. 220.65
10.27

5 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of
10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head,
comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame ,
concrete/ masonry, etc. as per direction of Engineer-in-charge.
10.27.3 100 Each ₹ 17,095.00
10 x 120 mm 170.95
Providing and fixing specified dia (in mm) of reinforcement bar in
existing RCC structure/ moment connection / splice connection
with specified embedment depth at any location directed by
6 Engineer -in- Charge, with chemical ((HILTI or Fischer make) as per
drawing and instruction, complete with all materials(approved chemical,
filling resin and hardener as per Design Engineer &
manufacturer's recomendations ) stagging and labour .
(Reinforcement bar wiil be paid in relevant item)

(a) 8mm dia 95 Each 246.00 ₹ 23,370.00

(b) 10mm dia 70 Each 271.00 ₹ 18,970.00
(c) 12mm dia 85 Each 320.00 ₹ 27,200.00
 Providing and fixing false ceiling at all heights including providing and fixing of frame work
made of special sections, power pressed from M.S. sheets and galvanized with zinc coating
of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25
mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre,
one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia
(d) 16mm dia 90 Each 341.00 ₹ 30,690.00
bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length
(e) with
20mm nuts
dia& bolts of required size and other end of angle hanger fixed with intermediate ₹ 113,850.00
110 Each 1,035.00
G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which
the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm
each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction
perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia
xDrilling
230 mm long G.I.
suitable holeswire
in at every junction,
reinforced or plainincluding fixing perimeter
cement concrete channels
with power driven0.5drill
mm thick
7 27 mm high
machine to ahaving
minimum flanges
depthof 20 mm andupto
of 100mm 30 mm long, in
200mm theRCC
perimeter
beams, of ceiling
lintels, fixed toand
columns
wall/partition withsteel
slabs to introduce the help
barsof forrawl plugs at 450 mm centre,
sunshades/balconies with
including 25 mm
fixing the long
steeldry
barswall
in
screws
position@using
230 mm
epoxy interval, including
resin anchor fixing
grout of gypsummake
of approved boardbuttoexcluding
ceiling section andof
the cost
perimeter channel with the help of dry wall screws of size
reinforcement, all complete as per direction of Engineer-In-Charge. 3.5 x 25 mm at 230 mm c/c,
including jointing and finishing to a flush finish of tapered and square edges of the board
with
Uptorecommended jointing
and including 12mm compound , jointing tapes , finishing with jointing compound
dia. 610 Each 121.95 ₹ 74,389.50
in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable
for board, all as per manufacturer’s specification and also including the cost of making
8 openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels
suitably fixed, all complete as per drawings, specification and direction of the Engineer in
12.45 Charge but excluding the cost of painting with :

12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- 350 ₹ 532,035.00
12.45.2 (Part 3):1996 (Boards with BIS certification marks) sqm 1520.1

P Road, Parking & Dranage

1 Supplying and stacking at site.

(a) 16.3.5 580 Cum ₹ 505,789.00
Over burnt (Jhama) brick aggregate 90 mm to 45 mm 872.05

(b) Supplying, stacking and Spreading 6 mm thick red bajri, watering and rolling complete
including preparation of the surface and rolling.
16.6 With road roller/ hand roller 1850 Sqm 24.45 ₹ 45,232.50

16.68

2 Providing and laying 60mm thick faciory made cement concrete interlocking paver block of 1820 Sqm 972 ₹ 1,769,040.00
M -30 grade made by block making machine with strong vibratory compaction, of
approved size, design & shape, laid in required colour and pattern over and including
50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete
as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade
3 cement concrete in position to the required line, level and curvature, jointed with cement
mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves
(thickness of joints except at sharp curve shall not to more than 5mm), including making
drainage opening wherever required complete etc. as per direction of Engineer-in-charge
(length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone
shall be approved by Engineer-in-charge).
 16.69 400x375x200(mm) 135 Cum 10117.6 ₹ 1,365,876.00

4 Dry brick pitching half brick thick in drains including supply of bricks and preparing the
surface complete :
16.12 250 Sqm ₹ 161,012.50
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 644.05

5 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey
cement slurry mixed with pigment to match the shade of the slab, including rubbing and
polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
11.26 25 mm thick 100 Sqm 1948.25 ₹ 194,825.00

19.6
6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed
with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand)
including testing of joints etc. complete :
19.6.4 300 mm dia. R.C.C. pipe 250 Rmt 994.3 ₹ 248,575.00
19.6.2 150 mm dia. R.C.C. pipe 150 Rmt 556.45 ₹ 83,467.50

7 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar
1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating
with frame complete as per standard design :
19.27 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 68 Each 5957.9 ₹ 405,137.20

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand )
with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone
8 aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand
(zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick
with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat
cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement
19.7 complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610
mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight
19.7.1 of cover 23 kg and weight of frame 15 kg)
19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 12770.55 each 10 ₹ 127,705.50
 Constructing brick masonry chamber for underground C.I. inspection chamber and bends
with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light
9 duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less
than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3
mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation
concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size),
inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished
smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per
standard design:

Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :
19.30.2 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 6 Each 8150.5 ₹ 48,903.00

10 Making connection of drain or sewer line with existing manhole including breaking into
and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse
sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with
cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement
and making necessary channels for the drain etc. complete :
19.21 For pipes 100 to 250 mm diameter 4 Each 810.45 ₹ 3,241.80

11 19.22 Providing sand cast iron drop connection externally for 60 cm drop from branch sewer line
to main sewer manhole including inspection and cleaning eye with chain and lid, sand cast
iron drop pipe and bend encased all-round with cement concrete 1:5:10 (1 cement : 5 fine
sand : 10 graded stone aggregate 40 mm nominal size) with all centering and shuttering
required, cutting holes in walls and making good with brick work in cement mortar 1:4 (1
cement : 4 coarse sand) plastered with cement mortar 1:3 (1 cement : 3 coarse sand) on
inside of the manhole wall, lead caulked joints between sand cast iron pipes and fittings,
stiff cement mortar 1:1 (1 cement : 1 fine sand) joints between sand cast iron tee and S.W.
pipe, making required channels complete as per standard design and specifications
19.22.2 150 mm dia sand cast iron drop connection 2 Each 16577.8 ₹ 33,155.60

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete
blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as
per standard design :
12 19.15 With 20x20 mm square bar 42 Each 544.7 ₹ 22,877.40
19.16

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as
per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross
section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with 20 Each 553.7 ₹ 11,074.00
minimum 112 mm space between protruded legs having 2 mm tread on top surface by
ribbing or chequering besides necessary and adequate anchoring projections on tail length
on 138 mm as per standard drawing and suitable to with stand the bend test and chemical
resistance test as per specifications and having manufacture’s permanent identification
mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement
concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal
size) complete as per design.

₹ 109,774,800.53
Remarks