Skip to content
jahurtadoPublic
forked from ijigen/fpSup

About

SIGMA fp Enhancement Project

Resources

Stars

1 star

Watchers

0 watching

Forks

 
 

Latest commit

 

History

354 Commits

Folders and files

Repository files navigation

fpSup

supMe on Ko-fi Join the fpSup Discord

SIGMA fp firmware research and on-camera tools. SIGMA fp 韌體研究與機身端工具。

English | 繁體中文 · → ijigen.github.io/fpSup

Everything here runs from an AutoRun.txt on the SD card, in RAM only. Remove the file, power-cycle, and the camera is stock. Nothing is ever written to flash. Firmware Ver.5.02 only — a card built for one version writes into whatever happens to be at those addresses on another.


English

Start here

ijigen.github.io/fpSup — the tools, the releases and the reference, in one page.

fpSup-Merge — pick the products you want on one card and get AutoRun.txt and fpSup.BIN. Merged cards are produced here and nowhere else, and every combination is checked against the same rules the build scripts use. Runs in the browser — no toolchain, no camera.

Releases

Two files each — copy AutoRun.txt and the payload container to the root of the card (fpSup.BIN; releases published before 2026-09-19 name it VSHL.BIN). No folder to make, nothing to convert, no step afterwards. To put two of them on one card, use the composer rather than copying both.

product version what it does

| fpsup-gyro | v1.14.0 | Writes Gyroflow's .gcsv and .json while recording — every sample at 2500 Hz, distortion read off the lens. The profile now carries the size the take was actually recorded at, which open gate got wrong. | | fpsup-gyro-base | v1.14.0 | Writes the gyro and accelerometer as a raw .GYR in the root of the disk the take went to — every sample, nothing on the camera but the stream — converted afterwards in a browser. Same code as fpGyroSup v1.14.0. | | fpsup-og2k | v0.1.3a | The same open gate at 2016×1344, on the sensor's quiet readout at every frame rate. 98 MB/s at 24p 12-bit, 8.3 ms rolling shutter. Test build. | | fpsup-og3k | v0.2.6a | The sensor's whole 3:2 area at 3024×2010, eight frame rates from 23.976 to 100, native UI in Settings and Quick Set. 221 MB/s at 24p 12-bit — this needs an external SSD, not an SD card. Alpha. | | fpsup-raw-view | v0.2.2test | RAW monitoring for CinemaDNG 12-bit: a RAW row in the COLOR menu makes the LCD show what will be recorded — recording gain in standby, sensor saturation as white, two latitude curves (SA/GA) mapped onto a 709 screen. The recorded RAW is not changed. Test build; ordinary card and Fast Start 2. | | fpsup-usbshell | v3.3.0 | The shell that answers shl over USB, parasitic on the camera's own PTP gadget so the firmware keeps owning the endpoints. |

The two open-gate builds see the same picture. OG2K is the sensor reduced by three rather than two, so it is a third of the data and stays on the quiet readout even at 100p. They cannot share a card — the resolution menu holds three entries and each build takes the third. Super35/crop must be off for either. Both are pre-release; each release's README.txt lists exactly what was verified and what was not. Open gate on an fp was first done by Vitaly Li.

Named fpsup-<product>-v<version>, one directory each, and the tag is spelled identically — see releases/README.md and releases/TAGS.md.

The thing most likely to bite: CinemaDNG is limited by write speed long before anything else. Open gate at 24p is about 221 MB/s at 12-bit, 184 at 10-bit and 148 at 8-bit; a mid-range UHS-II card measured here sustains 94, and plain FHD 12-bit already needs 97. A card that cannot keep up buffers in RAM and then stops the take. That is the card, not a bug — tools/storage-benchmark/ measures yours.

Projects

Each page says what has been proven, what is being worked on, and what is open.

# Project What it is Status
1 usb shell sup USB firmware research and data transport released — v3.2.0. The channel is built on the camera's own PTP gadget, so recording survives it
2 sensor lab sup IMX410 modes, ISO, gain, sensor control research complete — explainer, and the mode-table ambiguity closed
3 gyro sup Gyro, six-axis logging, Gyroflow workflow released — two editions; Base writes a raw .GYR instead, converted in a browser
4 open gate Recording the sensor's full 3:2 area OG3K v0.2.5a alpha · OG2K v0.1.2a test — 3024×2010 or 2016×1344, same field of view; Super35/crop must remain off
5 6k to ssd Getting the best 6K the link can carry designed; 8-bit lands within 94–100% of native 6K across every remaining unknown
6 focus sup DFD, focus model, lens control, follow focus AF decompiled in depth; no collector built
7 raw sup Bayer capture, streaming, compression, packaging researched; the engine's sustained rate is still the one unmeasured number
8 ui sup On-screen display, boot animation text, colour and a hardware overlay line all work on a camera
9 power sup USB-C power delivery and power saving charging mechanism solved; the rest untouched
— firmware map Format, subsystems, task ABI, state sources ongoing — not a product, the ground the rest stands on
Stopped or paused — kept because what they established still holds
Project Why it is here
bridge — sigma-fp-bridge The most complete thing built on the fp's PTP surface. Its measurements of why host-side autofocus is hard, and that UHD 12-bit CinemaDNG cannot come over USB, are load-bearing here
gimbal SIGMA's 0x94xx vendor protocol works during recording, unlike tethered focus. Relative drive only, but absolute position is readable
color sup The colour is reproduced; the tool is awkward and nothing is packaged
fpRemote Not started. Wireless bridge and low-resolution streaming through AutoRun rather than PTP

Headline results

  • The camera writes its own Gyroflow files while it records. The GCSV streams during the take and the JSON lands a few seconds in; stop is just stop. Zero dropped samples over a 15-minute take, timestamps verified row by row.
  • The 12-bit open-gate path works across every ISO, with native Settings and Quick Set UI. 3024×2010 of a 3:2 sensor read, edge to edge — verified by unpacking a real take, not inferred. v0.2.2a adds 8-bit and 10-bit: all three depths were measured recording at OG3K geometry, where 8 and 10-bit previously fell back to UHD30 without any on-screen sign. v0.2.1a's four-callsite shutter-angle fix and loader instruction-cache synchronization carry forward. v0.2.3a fixes v0.2.2a's format-table pass-through pointer; all 100 DNGs in exact no-shell OG3K/UHD/FHD 25p/180° tests recorded at 1/50 with correct geometry. Super35/ crop must remain off. 8/10-bit playback and highlight headroom, other frame rates, sustained-media and playback-with-UI regressions remain.
  • The IMX410 ISO and gain chain is fully decompiled, with an explainer that separates firmware-confirmed behaviour from OTP values still needing measurement.
  • The USB shell does not break recording. It is built on the camera's own PTP gadget, so the firmware owns the endpoints and re-creates them after a record-mode reconfiguration.

Reference

docs/SHELL_COMMANDS.md the firmware shell's 77 commands, with usage text asked from a live camera
docs/SHELL_CAPABILITIES.md what those commands reach — memory and I²C writes, menu setters, sensor readout modes
docs/MENU_MODIFICATION.md every menu item carries its own metadata in ROM, right after its name string
docs/FREEZE_ROOTCAUSE.md why the first USB shell froze the camera, mechanism and all
BUILDING.md how a card works and how to build, combine, test and release one — the walkthrough (中文)
SUP_BUILD_RULES.en.md the build contract every sup follows (中文)
HOOKS_AT_POWER_OFF.md why a hook must come out at power-off, and how

繁體中文

從這裡開始

ijigen.github.io/fpSup —— 工具、釋出版、參考資料都在一頁。

fpSup-Merge —— 勾選要的產品, 產生 AutoRun.txt 與 fpSup.BIN。合併版只在這裡產生,而且每個組合都用建置腳本 同一套規則檢查過。在瀏覽器裡跑 —— 不用工具鏈,不用相機。

釋出版

每份就兩個檔 —— AutoRun.txt 與 fpSup.BIN(2026-09-19 之前發布的版本叫 VSHL.BIN)放進卡片根目錄。不用建資料夾、不用轉檔、事後沒有步驟。要把兩份放同一張卡,用合併器,不要兩份都複製。

產品 版本 做什麼

| fpsup-gyro | v1.14.0 | 錄影當下就把 Gyroflow 要的 .gcsv 與 .json 寫進片段資料夾。2500 Hz 每個樣本都在,畸變直接讀鏡頭。profile 的尺寸改成實際錄下的那個 —— open gate 下先前是錯的。 | | fpsup-gyro-base | v1.14.0 | 在錄影那顆磁碟的根目錄寫一個原始 .GYR(陀螺儀與加速度計每個樣本都在),機上只做串流,事後在瀏覽器轉換。與 fpGyroSup v1.14.0 同一份程式。 | | fpsup-og2k | v0.1.3a | 同樣的 open gate,2016×1344,每個幀率都走感光元件的安靜讀出。24p 12-bit 為 98 MB/s,捲簾 8.3 ms。測試版。 | | fpsup-og3k | v0.2.6a | 感光元件完整的 3:2 面積,3024×2010,八個幀率從 23.976 到 100,Settings 與 QS 有原生 UI。24p 12-bit 為 221 MB/s ——這個碼率要外接 SSD,SD 卡不夠。Alpha。 | | fpsup-raw-view | v0.2.2test | CinemaDNG 12-bit 的 RAW 監看:COLOR 選單多一列 RAW,螢幕顯示即將錄下的內容——待機用錄影增益、感光元件飽和即白、兩條寬容度曲線(SA/GA)映射到 709 螢幕。錄下的 RAW 不被改動。測試版;附一般卡與 Fast Start 2 卡。 | | fpsup-usbshell | v3.3.0 | 透過 USB 回應 shl 的 shell。寄生在相機自己的 PTP gadget 上,端點仍由韌體管。 |

兩個 open gate 看到的是同一個畫面。 OG2K 是把感光元件縮三倍而不是兩倍,所以資料量只有三分之一, 而且連 100p 都還在安靜讀出上。兩者不能放同一張卡 —— 解析度選單只有三格,各自佔用第三格。 **兩者都必須關閉 Super35/crop。**都還是預覽版:各自的 README.txt 寫明了驗過什麼、沒驗什麼。 最早在 fp 實現 open gate 的是 Vitaly Li。

命名是 fpsup-<產品>-v<版本>,一個版本一個資料夾,tag 逐字相同 —— 見 releases/README.md 與 releases/TAGS.md。

最可能咬人的一件事: CinemaDNG 遠在其他東西之前就先被寫入速度卡住。 Open gate 24p 在 12/10/8-bit 各約 221 / 184 / 148 MB/s;這裡實測一張中階 UHS-II 卡持續寫入 94,而純 FHD 12bit 就已經要 97。撐不住的卡會先用 RAM 緩衝,然後停止錄影 —— 那是卡不是 bug。用 tools/storage-benchmark/ 量自己的。

項目

每一頁都寫清楚已經證實了什麼、正在做什麼、還有什麼沒解。

# 項目 是什麼 狀態
1 usb shell sup USB 韌體研究與資料傳輸 已釋出 —— v3.2.0。通道建在相機自己的 PTP gadget 上,所以錄影撐得過去
2 sensor lab sup IMX410 模式、ISO、增益、感光元件控制 研究完成 —— 互動說明,模式表的歧義也收掉了
3 gyro sup 陀螺儀、六軸記錄、Gyroflow 流程 已釋出 —— 兩個版本;Base 版寫原始 .GYR,在瀏覽器裡轉換
4 open gate 錄下感光元件完整的 3:2 面積 OG3K v0.2.5a alpha · OG2K v0.1.2a test —— 3024×2010 或 2016×1344,視角相同;Super35/crop 必須關閉
5 6k to ssd 把鏈路載得動的最好 6K 拿出來 設計完成;8bit 在所有剩餘未知數下都落在原生 6K 的 94–100%
6 focus sup DFD、對焦模型、鏡頭控制、跟焦 AF 深度反編譯完成;收集器還沒做
7 raw sup Bayer 擷取、串流、壓縮、封裝 研究過;引擎的持續速率仍是唯一沒量到的數字
8 ui sup 螢幕顯示、開機動畫 螢幕出字可行;顏色編碼未解
9 power sup USB-C 供電與省電 充電機制已解;其餘未動
— firmware map 格式、子系統、任務 ABI、狀態來源 進行中 —— 不是產品,是其他東西站著的地面

主要成果

  • 相機自己在錄影當下寫出 Gyroflow 要的檔案。 GCSV 邊錄邊串流,JSON 開始幾秒後落地,停止就只是停止。15 分鐘的 take 零掉樣,時間戳逐列驗過。
  • Open gate 的 12-bit 路徑已驗證全 ISO,原生 UI 已整合。 3:2 讀出的 3024×2010,整幅邊到邊 —— 解檔實錄驗證,不是推論。v0.2.2a 新增 8-bit 與 10-bit;v0.2.3a 修正 format-table pass-through 指標。精確 no-shell 的 OG3K/UHD/FHD 25p/180°三段共100張 DNG 全為1/50且幾何正確。OG3K 必須關閉 Super35/crop。8/10-bit 的回放與高光餘裕、其他幀率、長時間寫入與新 UI runtime 回放仍待回歸。
  • IMX410 的 ISO 與增益鏈完整反編譯,說明頁把「韌體確認的行為」跟「還需要量測的 OTP 值」分開。
  • USB shell 不會弄壞錄影。 它建在相機自己的 PTP gadget 上,端點由韌體管,錄影模式重配之後韌體會自己重建。

參考

BUILDING.zh.md 卡片怎麼運作、怎麼建卡、合併、測試與發布 —— 完整流程說明(English)
SUP_BUILD_RULES.md 每個 sup 都要遵守的建置規範(English)
HOOKS_AT_POWER_OFF.md 為什麼 hook 關機時必須拆掉、怎麼拆(英文,附中文摘要)

Support · Ko-fi · Discord

About

SIGMA fp Enhancement Project

Resources

Stars

1 star

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages