Skip to content
anarkiwiPublic

About

"tape" loader for PAL-II KIM-1 replica boards

Resources

Stars

0 stars

Watchers

0 watching

Forks

Latest commit

 

History

19 Commits

Folders and files

Repository files navigation

kimtape

Paper tape loader for the MOS Technology KIM-1 and its replicas. Loads, dumps and verifies programs over a serial line using the stock ROM monitor — no extra hardware, no pyserial, standard library only. load bootstraps a small XMODEM receiver through the monitor and sends the program at 38400 baud, about 40 times faster than paper tape records at 1200.

Works with the KIM-1, PAL-1, PAL-II, Micro-KIM, KIM Clone and simulators exposed on a pty.

Install

pip install kimtape

Use

kimtape load  --port /dev/ttyUSB0 zp.ptp game.ptp --go 0200
kimtape load  --port /dev/ttyUSB0 --hex game.ptp   # records only, no loader
kimtape dump  --port /dev/ttyUSB0 --range 0200-0774 -o game.ptp
kimtape run   --port /dev/ttyUSB0 --go 0200
kimtape tune  --port /dev/ttyUSB0     # fastest hex record settings for this board
kimtape probe --port /dev/ttyUSB0     # what does this board answer, and how?
kimtape term  --port /dev/ttyUSB0     # raw terminal, ^] to quit
kimtape info  game.ptp                # parse a tape without a board

Tapes and images may be http(s) URLs, fetched on the fly:

kimtape load --port /dev/ttyUSB0 \
  https://github.com/anarkiwi/kimformer/releases/latest/download/kimdos-0400.ptp --go 0400

Programs distributed as raw binaries, Intel HEX or S-records — fig-FORTH, xKIM, MICRO-ADE among them — convert first:

kimtape convert forth.bin --at 2000 -o forth.ptp
kimtape convert xKIM.hex -o xkim.ptp          # format read from the content

Press RS before running: the monitor sets its bit rate from the first carriage return it receives. Defaults are 1200 baud, 8N1, no flow control.

load falls back to 19200, then 9600 baud, then hex records by itself if 38400 does not work; --baud-fast caps the first rate and --hex skips the loader. Hex records, the loader's included, stream in frames sized from the monitor's own timing, 255 bytes a record, and the monitor's checksums are trusted; --verify reads them back. load and dump move the monitor to 4800 baud for hex records and read back without a reset, and back afterwards, when --baud is slower; --monitor-baud RATE picks another rate, --monitor-baud 0 stays at --baud, and tune finds the fastest setting a board takes. The XMODEM loader reads each byte back as it stores it. probe reports what a board answers when something is wrong; start there.

As a library:

from kimtape import Monitor, Port, Tape
from kimtape.bootstrap import Bootstrap

port = Port("/dev/ttyUSB0", 1200)
mon = Monitor(port)
mon.sync()
tape = Tape("game.ptp", open("game.ptp", "rb").read())
if not Bootstrap(mon, [38400, 19200, 9600], baud=4800).load(tape.mem, go=0x0200):
    mon.load(tape)   # hex records
    mon.go(0x0200)

Examples

examples/load.py fetches any catalogued program from its own archive and loads it. The catalogue is examples/programs.toml; nothing is redistributed here.

examples/load.py --list
examples/load.py microchess --port /dev/ttyUSB0    # chess in 1K, on the keypad
examples/load.py kb9 --port /dev/ttyUSB0           # Microsoft BASIC, over this terminal
examples/load.py kimventure --port /dev/ttyUSB0

Most catalogued programs talk over the same serial line you loaded them through: BASIC, FOCAL, Tiny BASIC, two chess programs, an RPN calculator, a text editor and a disassembler. See docs/kim-software.md for what else is out there, and docs/kimventure.md for the worked example in full.

Documentation

Licence

Apache 2.0. Program images are fetched at run time and are not redistributed here; they remain the property of their authors.

About

"tape" loader for PAL-II KIM-1 replica boards

Resources

Stars

0 stars

Watchers

0 watching

Forks

Releases

Packages

Used by

Contributors

Languages