welcome to the rfcat project

= TOC =
* Goals
* Installing Hardware
* Installing Client
* Using RfCat
* Epiloque

== GOALS ==
the goals of the project are to reduce the time for security researchers to create needed tools for analyzing unknown targets, to aid in reverse-engineering of hardware, and to satiate my rf lust.

== DEVELOPMENT ==
new development efforts should copy the "application.c" file to "appWhateverMyToolIs.c" and attempt to avoid making changes to other files in the repo if at all possible.  that is only a recommendation, because future bug-fixes in other libraries/headers will go much more smoothely for you.

a couple gotchas to keep in mind while developing for the cc1111:
* the memory model includes both "RAM" and "XDATA" concepts, and standard RAM variables and XDATA variables have different assembly instructions that are used to access them.  this means that you may find oddities when using a function written for XDATA on a standard RAM variable, and vice-versa.
* variables should be defined in a single .c file, and then "externs" declared in a .h file that can be included in other modules.  this is pretty standard for c programs, but both this and the previous point caused me difficulties at some points, and i found myself unsure what was causing my troubles.
* RAM memory is not cheap.  use it sparingly.
* you need to set the radio into IDLE mode before reconfiguring it
* you need to set the radio into TX mode *before* writing to the RFD register (firmware) as it is a 1-byte FIFO.


== INSTALLING HARDWARE==
installing and getting up to speed with rfcat...

first things first.  using rfcat requires that you either use the python client in root mode (sudo works well), or configure udev to allow non-root users full access to the dongle. you must also have one of the supported dongles flashed with the necessary application firmware.

allowing non-root dongle access:

  create a file in /etc/udev/rules.d called 20-rfcat.rules with the following line in it:

    SUBSYSTEMS=="usb" ATTRS{idVendor}=="0451" ATTRS{idProduct}=="4715" MODE:="0666"

  reboot or run 'sudo udevadm control --reload-rules'

this tool is created, maintained, and used primarily on linux.  make and sdcc must be installed.

supported dongles:
* cc1111emk (aka DONSDONGLES)
* chronos watch dongle (aka CHRONOSDONGLE)
* imme (limited support for both IMME and IMMEDONGLE)
    * imme dongle is not really usable as of 1/31/2012

= INSTALLATION =
your build environment:
* intended development model is using a GoodFET (http://goodfet.sf.net) although one of our developers uses the chipcon debugger from ti.

  * wiring:

            --------------------------------
            |                         1  2 |
            |                         3  4 |
       ------                         5  6 |  
       | USB                          7  8 |
       ------                         9 10 |
            |                        11 12 |
            | GoodFET                13 14 |
            --------------------------------



  * Chronos Dongle Details
            --------------------------------
            |                              |
            |             RST 1  2 TP      ------
            |             GND 3  4 VCC      USB |
            |            P2.2 5  6 P2.1    ------
            | Chronos                      |
            --------------------------------

               GoodFET            Chronos
                 PIN                PIN

                  1 <----- DD -----> 6
                  2 <----- VCC ----> 4
                  5 <----- RST ----> 1
                  7 <----- DC -----> 5
                  9 <----- GND ----> 3


  * EMK Dongle Details
            --------------------------------
            | 2 4 6 8 10   2 4 6 8 10      |
            | 1 3 5 7 9    1 3 5 7 9
            |-TEST-PINS----DEBUG-PINS------|
            |                              |
       ------                              |
       | USB                               |
       ------                              |
            | Don's Dongle (EMK)           |
            --------------------------------

               GoodFET              EMK  
                 PIN             DEBUG PIN

                  1 <----- DD -----> 4
                  2 <----- VCC ----> 2
                  5 <----- RST ----> 7
                  7 <----- DC -----> 3
                  9 <----- GND ----> 1

* install sdcc
* install make
* make sure both are in the path
* cd into the "rfcat/firmware/" directory
* "make testgoodfet" will read info from your dongle using the GoodFET. you should see something like:

    SmartRF not found for this chip.
    Ident   CC1111/r1103/ps0x0400
    Freq         0.000 MHz
    RSSI    00

* "make backupdongle" will read the current firmware from your dongle to the file .../bins/original-dongle-hex.backup.
  ("make restoredongle") to revert to the original firmware. 
* "make clean installRfCatChronosDongle" will clean, build, and install the RfCat (appFHSSNIC.c) firmware for a Chronos dongle.
* "make clean installRfCatDonsDongle" will clean, build, and install the RfCat (appFHSSNIC.c) firmware for a cc1111emk.
* "make clean installimmesnifffw" will clean, build, and install the RfSniff firmware for the IMME girls toy from girltech 



= INSTALLING - CLIENT-SIDE =
install rfcat onto your system.  on most linux systems, this will place rfcat and rfcat_server in /usr/local/bin/ and rflib into /usr/*/lib/python2.x/dist-packages
installation is simple:

* cd into the rfcat directory (created by unpacking the tarball or by hg clone)
* sudo python setup.py
* i highly recommend installing "ipython" (for deb/ubuntu folk: apt-get install ipython)



= USING RFCAT - NON-root MODE =
if you have configured your system to allow non-root use:

* type "rfcat -r"
    you should have now entered an interactive python shell, where tab-completion and other aids should make a very powerful experience
    i love the raw-byte handling and introspection of it all.

* try things like:
    * d.ping()
    * d.discover()
    * d.debug()
    * d.RFxmit('blahblahblah')
    * d.RFrecv()
    * print d.reprRadioConfig()
    * d.setMdmDRate(19200)      # this sets the modem baud rate (or DataRate)
    * d.setPktPQT(0)            # this sets the preamble quality threshold to 0
    * d.setEnableMdmFEC(True)   # enables the convolutional Forward Error Correction built into the radio


while the toolset was created to make communicating with <ghz much easier, you will find the cc1111 manual from ti a great value.  the better you understand the radio, the better your experience will be.
play with the radio settings, but i recommend playing in small amounts and watch for the effects.  several things in the radio configuration settings are mandatory to get right in order to receive or transmit anything (one of those odd requirements is the TEST2/1/0 registers!)

if you watched any of my talks on rfcat, you will likely remember that you need to put the radio in IDLE state before configuring. (i said it three times, in a row, in different inflections).
however, you will find that i've done that for you in the client for most things.  the only time you need to do this yourself are:
    * if you are doing the changes in firmware
    * if you are using the "d.poke()" functionality
        * if you use "d.setRFRegister()", this is handled for you
** use d.setRFRegister() **



== EPILOGUE
other than that, hack fun, and feel free to share any details you can about successes and questions about failures you are able!

@ and the rest of the development team.