ESP32CAM-RTSP

Simple RTSP, HTTP JPEG Streamer and image server with configuration through the web interface.

Flashing this software on a ESP32CAM module will make it a RTSP streaming camera server, a HTTP Motion JPEG streamer and a HTTP image server.

• Features
• Supported boards
• Installing and running PlatformIO
• Putting the ESP32-CAM in download mode
• Compiling and deploying the software
• Setting up the ESP32CAM-RTSP
• Connecting to the configuration
• Connecting to the RTSP stream
• RTSP authentication
• Connecting to the JPEG motion server
• Connecting to the image server
• Updating the firmware (OTA)
• API
• Issues / Nice to know
• Credits

Supported protocols

• RTSP The RTSP protocol is an industry standard and allows many CCTV systems and applications (like for example VLC) to connect directly to the ESP32CAM camera stream. It is also possible to stream directly to a server using ffmpeg. This makes the module a camera server allowing recording and the stream can be stored on a disk and replayed later. The video is encoded as Motion-JPEG (RTP payload 26) and streamed over RTP/UDP (default) or RTP/RTSP/TCP. Boards with an onboard microphone (e.g. the Seeed Studio XIAO ESP32S3 SENSE) can additionally stream G.711 a-law audio (RTP payload 8). The URL is rtsp://<ip address>:554/mjpeg/1 Authentication is optional; when enabled, clients must provide credentials (see RTSP authentication).

• HTTP Motion JPEG The HTTP JPEG streamer makes it possible to watch the camera stream directly in your browser. The URL is http://<ip address>/stream

• HTTP image The HTTP Image returns an HTTP JPEG image of the camera. The URL is http://<ip address>/snapshot

• Over-the-air (OTA) firmware update The firmware can be updated over WiFi from PlatformIO or the Arduino IDE (espota). See Updating the firmware (OTA).

This software supports the following ESP32-CAM (and alike) modules:

• AI THINKER
• Espressif ESP-EYE
• Espressif ESP32S2-CAM
• Espressif ESP32S3-CAM-LCD
• Espressif ESP32S3-EYE
• Freenove WROVER KIT
• M5STACK ESP32CAM
• M5STACK_PSRAM
• M5STACK_UNITCAM
• M5STACK_UNITCAMS3
• M5STACK_V2_PSRAM
• M5STACK_WIDE
• M5STACK M5PoECAM-W
• M5STACK Timer CAM (Original and X)
• Seeed Studio XIAO ESP32S3 SENSE
• TTGO T-CAMERA
• TTGO T-JOURNAL

The software provides a configuration web server that can be used to:

• Provide information about the state of the device, WiFi connection and camera,
• Set the WiFi parameters,
• Set the timeout for connecting to the access point,
• Set an access password,
• Select the image size,
• Select the frame rate,
• Select the JPEG quality,
• Enable the use of the PSRAM,
• Set the number of frame buffers,
• Configure the camera options:
  • Brightness
  • Contrast
  • Saturation
  • Special effect (Normal, Negative, Gray-scale, Red/Green/Blue tint, Sepia)
  • White balance
  • Automatic White Balance gain
  • White Balance mode
  • White Balance mode
  • Exposure control
  • Auto Exposure (dsp)
  • Auto Exposure level
  • Manual exposure value
  • Gain control
  • Manual gain control
  • Auto gain ceiling
  • Black pixel correction
  • White pixel correction
  • Gamma correction
  • Lens correction
  • Horizontal mirror
  • Vertical flip
  • Downsize enable
  • Color bar

The software also provides a mDNS server to be easily discoverable on the local network. It advertises HTTP (port 80) and RTSP (port 554).

• ESP32-CAM module or similar,
• USB to Serial (TTL level) converter, piggyback board ESP32-CAM-MB or other way to connect to the device,
• PlatformIO software (free download)

There are a lot of boards available that are all called ESP32-CAM. However, there are differences in CPU (type/speed/cores), how the camera is connected, presence of PSRAM or not... To select the right board use the table below and use the configuration that is listed below for your board:

Board	Image	CPU	SRAM	Flash	PSRAM	Camera	Extras	Manufacturer site
Espressif ESP32-Wrover CAM		ESP32	520KB	4MB	8MB	OV2640
AI-Thinker ESP32-CAM		ESP32	520KB	4MB	4MB	OV2640		https://docs.ai-thinker.com/esp32-cam
Espressif ESP-EYE		ESP32	520KB	4MB	8MB	OV2640
Espressif ESP32-S3-EYE		ESP32-S3	520KB	4MB	8MB	OV2640		https://www.espressif.com/en/products/devkits/esp-eye/overview
LilyGo camera module		ESP32 Wrover	520KB	4MB	8MB	OV2640 / OV5640
LilyGo Simcam						OV2640
LilyGo TTGO-T Camera						OV2640
M5Stack ESP32CAM		ESP32	520KB	4MB	-	OV2640	Microphone	https://docs.m5stack.com/en/unit/esp32cam
M5Stack UnitCam		ESP32-WROOM-32E	520KB	4MB	-	OV2640		https://docs.m5stack.com/en/unit/unit_cam
M5Stack Camera		ESP32	520KB	4MB	-	OV2640		https://docs.m5stack.com/en/unit/m5camera
M5Stack Camera PSRAM		ESP32	520KB	4MB	4MB	OV2640		https://docs.m5stack.com/en/unit/m5camera
M5Stack UnitCamS3		ESP32-S3-WROOM-1-N16R8	520KB	16MB	8MB	OV2640		https://docs.m5stack.com/en/unit/Unit-CamS3
Seeed Studio XIAO ESP32S3 Sense		ESP32-S3R8	520KB	8MB	8MB	OV2640	Microphone	https://www.seeedstudio.com/XIAO-ESP32S3-Sense-p-5639.html

PlatformIO is available for all major operating systems: Windows, Linux and MacOS. It is also provided as a plugin to Visual Studio Code. More information can be found at: https://docs.platformio.org/en/latest/installation.html below the basics.

Install Visual Studio Code and install the PlatformIO plugin.

When using the ESP32-CAM-MB board, press and hold the GPIO0 button on the ESP32-CAM-MB board. Then press short the reset button (on the inside) on the ESP32-CAM board and release the GPIO0 button. This will put the ESP32-CAM board in download mode.

When using an FTDI adapter, make sure the adapter is set to 3.3 volt before connecting. Use the wiring schema below.

After programming remove the wire to the GPIO0 pin to exit the download mode.

Open a command line or terminal window and clone this repository from GitHub.

git clone https://github.com/rzeldent/esp32cam-rtsp.git

Go into the folder

cd esp32cam-rtsp

Next, the firmware has to be built and deployed to the ESP32. There are two flavours to do this; using the command line or the graphical interface of Visual Studio Code.

Make sure you have the latest version of the Espressif toolchain.

pio pkg update -g -p espressif32

First the source code has to be compiled to build all targets

pio run

If only a specific target is required, for example the esp32cam_ttgo_t_journal type:

pio run -e esp32cam_ttgo_t_journal

When finished, firmware has to be uploaded. Make sure the ESP32-CAM is in download mode (see previous section) and type:

 pio run -t upload

or, again, for a specific target, for example esp32cam_ai_thinker

pio run -t upload -e esp32cam_ai_thinker

When done remove the jumper when using a FTDI adapter or press the reset button on the ESP32-CAM. To monitor the output, start a terminal using:

 pio device monitor

Open the project in Visual Studio Code with the PlatformIO extension installed. Run the following tasks using Terminal -> Run Task (or Ctrl+Alt+T). Make sure the ESP32-CAM is in download mode during uploads.

• PlatformIO: Build (esp32cam) — compiles the firmware
• PlatformIO: Upload (esp32cam) — uploads the firmware to the device
• PlatformIO: Monitor (esp32cam) — opens the serial monitor to view debug output

After the programming of the ESP32, there is no configuration present. This needs to be added. To connect initially to the device open the WiFi connections and select the WiFi network / access point called ESP32CAM-RTSP. Initially there is no password present.

After connecting, the browser should automatically open the status page. In case this does not happen automatically, connect to http://192.168.4.1. In case this does not happen automatically, connect to http://192.168.4.1. This page will display the current settings and status. On the bottom, there is a link to the config. Click on this link.

This link brings up the configuration screen when connecting for the first time. This link brings up the configuration screen when connecting for the first time.

Configure at least:

• The access point to connect to. No dropdown is present to show available networks!
• A password for accessing the Access point (AP) when starting. (required)
• Type of the ESP32-CAM board

When finished press Apply to save the configuration. The screen will redirect to the status screen. Here it is possible to reboot the device so the settings take effect. It is also possible to restart manually by pressing the reset button.

After the initial configuration and the device is connected to an access point, the device can be configured over http.

The device announces itself on the local network via mDNS as esp32cam-rtsp-<mac>.local, where <mac> is the device's MAC address (also shown on the status page). Connect to http://esp32cam-rtsp-<mac> — or to the device's IP address — to open the status screen.

In case changes have been made to the configuration, this is shown and the possibility to restart is given.

Clicking on the change configuration button will open the configuration. It is possible that a password dialog is shown before entering. If this happens, enter the RTSP username and password configured under RTSP settings (see RTSP authentication).

RTSP stream is available at rtsp://esp32cam-rtsp-<mac>.local:554/mjpeg/1 (replace <mac> with the device's MAC address, or use its IP address). This link can be opened with for example VLC.

By default RTP is sent over UDP (the client announces its RTP ports in the SETUP request). When the network filters or firewalls UDP traffic, force the RTP/RTSP/TCP (interleaved) transport in VLC:

vlc rtsp://esp32cam-rtsp-<mac>.local:554/mjpeg/1 --rtsp-tcp

The server can stream over Secure RTP (RFC 3711, crypto suite AES_CM_128_HMAC_SHA1_80). SRTP encrypts the RTP payload with AES-128 in counter mode and authenticates every packet with an HMAC-SHA1 tag, so the video cannot be watched or tampered with by someone sniffing the network.

To enable it, build with the MICRO_RTSP_ENABLE_SRTP define, for example in platformio.ini:

build_flags =
  -DMICRO_RTSP_ENABLE_SRTP

The keys are negotiated per session with the a=crypto attribute (RFC 4568) that the server advertises in its DESCRIBE and SETUP replies. A client that offers its own a=crypto in the SETUP request enables SRTP for that session as well. Receive the stream with FFmpeg (which picks up the a=crypto key automatically):

ffmpeg -rtsp_transport tcp -i rtsp://esp32cam-rtsp-<mac>.local:554/mjpeg/1 -c copy out.mp4

The repository contains a small Python client, tools/srtp_client.py, that verifies the SRTP stream end-to-end. It negotiates SRTP by offering its own a=crypto attribute (RFC 4568) in the RTSP SETUP request, derives the session keys exactly like the firmware (lib/micro-rtsp-server/src/micro_rtsp_srtp.cpp), decrypts the incoming RTP, reassembles the JPEG frames (RFC 2435) and saves them to disk.

Requirements:

pip install cryptography

Usage:

python tools/srtp_client.py --host <ip address> [--port 554] [--rtp-port 50000]
    [--frames 5] [--time 10] [--out frames]

Example run:

python tools/srtp_client.py --host 192.168.1.149

--- SDP ---
v=0
o=- 1085377743 1 IN IP4 192.168.1.149
s=
t=0 0
m=video 0 RTP/AVP 26
c=IN IP4 0.0.0.0
a=control:track1

--- SETUP response ---
a=crypto:1 AES_CM_128_HMAC_SHA1_80 inline:TUAwUoKwQs9G/qhlrmG5KnVyh/ZXLVUxtcGgabHB
Content-Type: application/sdp

server master key : 4d40305282b042cf46fea865ae61b92a
server master salt: 757287f6572d5531b5c1a069b1c1
Receiving SRTP on UDP 50000 ...
  frame 1: 3166 bytes -> frames\frame_0001.bin
  frame 2: 2770 bytes -> frames\frame_0002.bin
  frame 3: 3373 bytes -> frames\frame_0003.bin
  frame 4: 3373 bytes -> frames\frame_0004.bin
  frame 5: 3373 bytes -> frames\frame_0005.bin

When the board has an onboard I2S microphone, an additional audio track is offered and streamed together with the video as G.711 a-law (PCMA, 8 kHz mono). VLC plays it automatically. Currently audio is enabled for the Seeed Studio XIAO ESP32S3 SENSE board (see boards/ and the MIC_I2S_* defines). To enable it on another board, add the microphone I2S pins to its board configuration, for example:

"'-D MIC_I2S_BCLK=17'",
"'-D MIC_I2S_WS=42'",
"'-D MIC_I2S_DIN=41'"

The stream can be recorded to disk, for example:

ffmpeg -rtsp_transport tcp -i rtsp://esp32cam-rtsp-<mac>.local:554/mjpeg/1 -c copy out.mp4

The RTSP server is implemented by the micro-rtsp-server library (in lib/micro-rtsp-server), a small single-threaded server that supports multiple simultaneous clients, RTP/UDP and RTP/RTSP/TCP transports, and (optionally) an audio track. The video frames are captured with esp32-camera, decoded with the micro-jpg library to locate the JPEG quantization tables, and packetized into RFC 2435 (JPEG over RTP) packets.

The RTSP server supports HTTP Basic authentication (RFC 2617). When enabled, clients must present the configured credentials before they can describe, set up or play the stream.

Authentication is disabled by default. To enable it, open the configuration page and set a username and password under the RTSP settings group, then apply the configuration and reboot.

When authentication is enabled:

• RTSP players such as VLC prompt for the username and password when connecting to the stream:

  vlc rtsp://esp32cam-rtsp-<mac>.local:554/mjpeg/1

• The credentials can also be embedded in the URL:

  vlc rtsp://<username>:<password>@esp32cam-rtsp-<mac>.local:554/mjpeg/1

• OPTIONS requests remain open (unauthenticated) so clients and monitoring tools can still probe the endpoint without credentials.

The same credentials protect the configuration page at http://esp32cam-rtsp-<mac>.local/config (HTTP Basic authentication, realm ESP32CAM-RTSP). The /snapshot and /stream pages are not password protected.

The JPEG motion server is available in a web browser at http://esp32cam-rtsp-<mac>.local/stream (replace <mac> with the device's MAC address).

The image server is available in a web browser at http://esp32cam-rtsp-<mac>.local/snapshot.

The device supports updating the firmware over WiFi (Over-The-Air, OTA), so it does not have to be connected to a USB programmer for every update.

Build the firmware normally and upload it over WiFi with PlatformIO, replacing the IP address and environment with your own. The --auth password MUST equal OTA_PASSWORD in include/settings.h (default ESP32CAM-RTSP) and must be passed without quotes (quotes become part of the password and break authentication):

pio run -t upload -e esp32cam_ai_thinker --upload-port 192.168.1.100 --upload-protocol espota --upload-flags=--auth=ESP32CAM-RTSP

The OTA password (OTA_PASSWORD in include/settings.h) is used to authenticate the update. The Arduino IDE (Tools -> Port -> Network Ports) or espota.py can be used as well:

python espota.py -i 192.168.1.100 -p 3232 -a ESP32CAM-RTSP -f .pio/build/esp32cam_ai_thinker/firmware.bin

There is a minimal API to perform tasks via HTTP requests. Some endpoints require HTTP Basic Authentication.

Set the credentials under RTSP settings on the configuration page (see RTSP authentication). When no RTSP username is set, authentication is disabled. The credentials are cached in the browser session, so you only need to enter them once.

The available endpoints are:

Calling this URL will restart the device. Authentication is required.

Calling this URL will start the form for configuring the device in the browser. Authentication is required.

Calling this URL will return a JPEG snapshot of the camera in the browser. This request can also be used (for example using cURL) to save the snapshot to a file.

• The red LED on the back of the device indicates the device is not connected.
• Sometimes after configuration a reboot is required. If the error screen is shown that it is unable to make a connection, first try to reboot the device,
• When booting, the device waits 30 seconds for a connection (configurable). You can make a connection to the SSID and log in using the credentials below,
• When connected, go to the ip of the device and, when prompted for the credentials, enter 'admin' and the AP password. This is a required field before saving the credentials,
• When the password is lost, a fix is to completely erase the ESP32 using the pio run -t erase command. This will reset the device including configuration. If using the esptool, you can do this using esptool.py --chip esp32 --port /dev/ttyUSB0 erase_flash. However, after erasing, re-flashing of the firmware is required.
• When finished configuring for the first time and the access point is entered, disconnect from the wireless network provided by the device. This should reset the device and connect to the access point. Resetting is also a good alternative...
• There are modules that have no or faulty PSRAM (despite advertised as such). This can be the case if the camera fails to initialize. It might help to disable the use of the PSRAM and reduce the buffers and the screen size.

Make sure the power is 5 volts and stable, although the ESP32 is a 3.3V module, this voltage is created on the board. If not stable, it has been reported that restarts occur when starting up (probably when power is required for WiFi). The software disables the brown out protection so there is some margin in the voltage. Some people suggest to add a capacitor over the 5V input to stabilize the voltage.

An unstable power supply is also the most common cause of horizontal color stripes/bands (blue, yellow or orange) in the camera image. The OV2640 sensor is sensitive to supply noise and voltage sag, which shows up as intermittent colored bands, often near the top or bottom of the frame. If you see these stripes:

• power the board from a stable 5V/2A supply on the 5V pin (not the 3.3V pin),
• use short, thick wires,
• add a 100–470 µF electrolytic capacitor across 5V and GND right at the board,
• avoid thin or long USB cables.

Some esp32cam modules have additional ram on the board. This allows to use this ram as frame buffer. The availability of PSRAM can be seen in the HTML status overview.

Not all the boards are equipped with PSRAM:

Depending on the image resolution, framerate and quality, the PSRAM must be enabled and/or the number of frame buffers increased to keep up with the data generated by the sensor. There are many boards around with faulty PSRAM. If the camera fails to initialize, this might be a reason — see this Reddit post. In this case disable the use of PSRAM in the configuration and do not use camera modes that require PSRAM.

For the setting JPEG quality, a lower number means higher quality. Be aware that a very high quality (low number) can cause the ESP32 cam to crash or return no image.

The default settings are:

• Frame size: QVGA (320×240)
• JPEG quality: 12 with PSRAM, 14 without PSRAM
• Frame buffers: 2

Be careful when connecting the camera module. Make sure it is connected the right way around (Camera pointing away from the board) and the ribbon cable inserted to the end before locking it.

If the image shows horizontal color stripes or bands (e.g. blue, yellow or orange), the most likely causes are:

• Power supply instability (most common) — see Power above.
• Frame tearing — reading a frame buffer while the camera is still writing it; keep at least 2 frame buffers.
• Flickering artificial light — the rolling shutter beats against LED/fluorescent flicker; test by covering the lens.
• WiFi interference — the antenna sits close to the camera; try lowering TX power or repositioning.

esp32cam-rtsp depends on PlatformIO, IotWebConf, Bootstrap 5, micro-moustache and micro-timezonedb, plus the bundled micro-rtsp-server and micro-jpg libraries.

• August 2026
  • Rewrote the RTSP server (micro-rtsp-server): RTP/UDP and RTP/RTSP/TCP, SRTP, G.711 audio
  • Improved streaming stability and performance
  • Added over-the-air (OTA) firmware updates via ArduinoOTA/espota, with an OTA-capable partition table (partitions/ota.csv) for the 4MB boards
• August 2024
  • Added support for M5Stack M5PoECAM-W
• January 2024
  • Moved settings to board definitions
  • Added new boards
  • Removed OTA to increase performance
• October 2023
  • Added support for Seeed Xiao esp32s3
  • New build system
  • Updated documentation
• March 2023
  • Added options to set PSRAM / Frame buffers
  • Added JPEG Motion streaming
• February 2023
  • Added additional settings for camera configuration
• November 2022
  • Added OTA
  • Fix for grabbing frame
  • Fixed bug: Increased WiFi password length
• September 2022
  • Added GUI with Bootstrap
  • More information in web page
  • Added camera preview in HTML
• July 2022
  • Initial version