Chery QQ Service Manual
Chapter 14 Removing Windshield
1. Remove the following parts:
（1）front seat
（2）rear seat cushions
（3）bolts on the lower end
of rear seat belt
（4）back of rear seat
（5）front door frame plate
（6）back door frame plate
（7）decorative side plate
of rear seat
（8）upper parking lamp
（9）speaker mesh guard
（10）decorative board
of glove compartment
(11）assistant grasp
(12）small rear seat lighting bulb
(13）interior roof lateral ornament
（14）middle pillar ornament
（15）front pillar ornament
(16) sun shading board and holder
（17）small illuminating light
（18）middle sun shading boards
（19）interior rear-view mirror
（20）front roof lining
（21）windshield wiper arms
（22）sealing strips for windshield
- 258 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
2. Remove front door sealing strips
Pull out sealing strips by hand
3. Remove outside inlaid strips
Take down screws and outside inlaid strips
4. Remove the upper inlaid strips
on windshield
As showed in the figure：Cut off
inlaid strips with knife
Attention：Do not let knife damage
car body
5. Remove windshield
（1）Lead piano wire out between car
body and windshield from interior car
（2）Bind up two wires ends with wood
blocks or similar objects
Note：Stick a piece of adhesive tape outside to prevent windshield external
surface from being scratched
Attention：
（1）Do not damage paint surface, internal
and external ornaments when detaching
windshield
（2）To avoid the scratch on dashboard, bonding agent piano wire
a sheet plastic can be placed between
piano string and dashboard
Drag the wire along all sides of windshield
to cut off bonding agent to remove windshield
Attention：Bonding agent should be kept on car body as much as possible
when cutting windshield joint
- 259 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
1. Installation of Windshield
（1）No touch on windshield surface
after cleaning
(2) Cut roughness off bonding agent sticking bonding agent
to car body with knife
Note：Keep bonding agent on car body
as much as possible
（3）Clean the cutting surface of
bonding agent with a rag soaked in cleaning liquid
Note：Even though all of bonding agent is completely removed, car body surface must
be cleaned
2. Remove block stop：
Remove block stop with knife
stop
3. Clean the removed windshield
（1）Remove the bonding agent stuck
on windshield with scraper
（2）Clean windshield with cleaning
liquid
Attention：Do not touch windshield
after cleaning
4. Replace clamps if necessary
（1）Remove stops with knife
（2）Take down used clamps
（3）Put new clamps on
- 260 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
5. Position windshield
（1）Put windshield in right place
（2）Make reference marks on windshield
and car body
（3）Remove windshield
6. Clean the joint surface of windshield
Clean the black dirt with clean liquid on
the joint surface of windshield periphery
Attention：Do not touch windshield
surface after cleaning
7. Install water-resisting chips
As showed in the drawing，fix water-
resisting chips with double-side
7mm (0.28in)
adhesive tape
Attention：Do not touch windshield
surface after cleaning
8. Coat a layer of base paint M
base paint M base paint M
on the joint surface of car body
Brush a layer of base paint M
onto the joint surface of car body base paint M
bonding agent
Attention：
（1）Wait for base coating layer
to dry over 3 minutes
（2）No coating on bonding agent
（3）Never reserve unsealed base paint M
for later use
- 261 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
9. Coat a layer of base paint G on the
base paint G
contact surface of windshield
（1） Coat a layer of base paint G with brush
or sponge on windshield periphery and
joint surface
（2） Clear base paint with a clean rag
before drying
Attention：
（1）Leave base paint layer dry for 3 minutes at least
（2）No coating on bonding agent
（3）Never reserve unsealed base paint G for later use
10. Mix bonding agent
Attention：
A. Ensure the fixation of inlaid strip to
finish within the applicable duration
of bonding agent
B. Mixing bonding agent must be
completed within 5 minutes
（1） Clean glass plate and oil loam scraper
thoroughly with solvent
(2 ) Fully mix 500g principal agent with
75g hardening agent with scraper on
glass plate or similar object
11. Apply bonding agent
（1）Cut off the Note of tubular pot and fill
bonding agent in the pot
（2）Put the pot into sealing glue gun
10mm (0.39in)
（3）Apply bonding agent on windshield
as showed in the drawing
- 262 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
12. Install windshield
bonding agent
Note：Verify that water- resisting chips have
been stuck on the face plate of car body
as showed in the drawing
（1）When install windshield,
align the reference marks
on windshield and car body, then
gently press in windshield towards
periphery
（2）Smear windshield at periphery
with bonding agent
（3）Remove excess or spilled bonding
agent with scraper
（4）Fasten windshield until bonding
agent hardened
13. Water leakage checking and maintenance 2.7mm (0.11in)
（1）Water leakage test shall be conducted
after hardening period
(2) Block up water leaking places with
sealant
14.Install upper inlaid strips on windshield
Put upper inlaid strips on car body and pat the strips by hand to tighten
- 263 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
15. Fix outside inlaid strips
Fix screws and outside inlaid strips
16. Fix front door sealing strips
17. Install the following parts：
（1）front roof lining
（2）interior rear-view mirror
（3）middle sun shading boards
（4）small illuminating light
（5）sun shading boards and holder
（6）front pillar ornament
（7）middle pillar ornament
（8）inner roof lateral ornament
（9）small rear seat lighting bulb
（10）decorative board of glove compartment
（11）assistant grasp
（12）speaker mesh guard
（13）lateral ornament of rear seat at upper parking lamp
back door frame plate
back of rear seat
Torque：18 N.m（185 kgf/cm，13 lbf/in）
bolts on the lower end of rear seat belt
Torque：43 N.m，32 lbf/in）
rear seat cushions
front seats
Torque：37 N/m（375 kgf/cm，27 lbf/in）
windshield
sealing strips for windshield
windshield wiper arms
- 264 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
Remove rear window glass
1. Remove the following parts：
rear seat cushions
bolts on the lower end of rear seat belt
back of rear seat
speaker mesh guard
upper parking lamp
decorative board of glove compartment
assistant grasp
small rear seat illuminating light
inner roof lateral ornament
2. Detach roof lining
3. Disconnect rear window connector
Disconnect rear window connector
4. Remove lower inlaid strips
As showed in the drawing, cut off the double-side adhesive tapes
on the two ends of inlaid strip with scraping cutter
Note: Before using, scraping cutter point shall be bandaged with adhesive tape
Prize out inlaid strips at six clamps and take the strips down
5. Remove rear window glass
Lead piano wire out between car body and glass
Bind up two wire ends with wood blocks or similar objects
Note：Do not let piano wire damage two stops
Remove the glass
6. Remove rear window inlaid strips
- 265 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
Install rear window glass
1. Fixing rear window inlaid strips
Put inlaid strips on glass periphery and
fix the strips by hand
Note：Rear window glass must be removed
before fixing inlaid strips
2. Clean and finish the joint surface
of car body bonding agent
Cut roughness off bonding agent sticking to
car body with knife
Note：Keep bonding agent on car body
as much as possible
Clean the cutting surface of bonding
agent with a rag soaked in cleaning liquid
Note：Even though all of bonding agent is completely removed,
car body must be cleaned
3.Remove block stop：
Remove block stop by knife
Block stop
4. Clean removed glass
Remove the bonding agent stuck on glass
with scraper
Remove block stop by knife
Clean glass with cleaning liquid
Attention：Do not touch glass after cleaning
- 266 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
5. Position glass
Put glass in right place
Make reference marks on glass and car body
Remove glass
6. Clean the joint surface of glass
Clean the black dirt with clean liquid
on the joint surface of glass periphery
Attention：Do not touch glass surface
after cleaning
Coating a layer of base paint M
on the joint surface of car body
base paint M base paint M
Brush a layer of base paint M
onto the joint surface of car body
Attention：Leave base coating layer dry
base paint M
for 3 minutes at least bonding agent
No coating on bonding agent
Never reserve unsealed base paint M for later use
7. Coat a layer of base paint G on the joint
surface of glass base paint G
Coat a layer of base paint G with brush or
sponge on glass periphery and joint surface
Clear base paint with a clean rag before drying
Attention：Leave base paint layer dry for
3 minutes at least
No coating on bonding agent
- 267 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
Never reserve unsealed base paint G for later use
8. Mix bonding agent
Attention：Ensure the fixation of inlaid strip
to finish within the applicable duration of
bonding agent
Mixing bonding agent must be completed
within 5 minutes
Clean glass plate and oil loam scraper
thoroughly with solvent
Fully mix 500g principal agent with 75g hardening agent with scraper
on glass plate or similar object
9. Applying bonding agent
Cut off the tip of tubular pot and fill bonding
agent in the pot
Put the pot into sealing glue gun
Apply bonding agent on glass as showed
in the drawing
10.Install glass
When installing windshield, align the
reference marks on glass and car body, then
gently press in glass towards periphery
Smear glass at periphery with bonding agent
using scraper
Remove excess or spilled bonding agent with scraper
Fasten glass until bonding agent hardened
11. Water leakage checking and maintenance
Water leakage test shall be conducted after curing time
Block up water leaking places with sealant
- 268 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
12. Fix lower outside filler strip on rear window
Put inlaid strips on car body and tighten the strap by patting
Attach wire connector for defroster
Install the following parts：
roof lining
inner roof lateral ornament
small rear seat illuminating light
assistant grasp
decorative board of glove compartment
upper parking lamp
speaker mesh guard
back of rear seat
Torque：18 N.m（185 kgf/cm，13 lbf/in）
bolts on the lower end of rear seat belt
Torque：43 N.m（440 kgf/cm，32 lbf/in）
rear seat cushions
When installing, the sequence is the reverse procedure of removal
- 269 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
Chapter 15 Wiper
Remove front windshield wiper assembly
（1） Pull out sealing strip
（2） Prize up decorative plate
（3）Loosen set bolts and take down wiper arm
（ 4 ） Loosen ten fixing screws to get out
decorative plate
（5）Prize out link rod
（6）Loosen six fixing nuts on the left and right
sides of link rod to take down link rod assembly
（7） Loosen four set bolts on wiper motor and take down the motor
Remove blade
Loosen seven set bolts and take down blade
Remove rear window wiper assembly
- 270 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
（1）Loosen eight screws on fastener and get out decorative plate
（2）Loosen three fixing screws on wiper motor and take down the motor
Remove jet washer
（1）Remove front bumper
（See the chapter on removal of
front bumper）
（2）Loosen three set bolts and take down
jet washer
（3） Loosen cable plug and move out and upward to get out front and rear jet
- 271 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
washer motors
Remove nozzle
Pull out the nozzle upwards to take apart with the tube
When assembling, the sequence is the reverse procedure of removal.
- 272 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
Chapter 16 Sun -Roof
Remove sun-roof assembly
（1） Unfasten twenty four fixing screws
on sun-roof and car body
（2） Prize up and take down the plastic
protective cover on sun-roof
（3）Get sun-roof assembly out
Check the position of sun-roof glass
Rear
rearrim
Check if there is water leakage when rim
sun-roof is completely closed
Check if there is vertical separation front rim
Front rim
between sealing strip and roof sheet
Front rim:
0±1.0 mm（0±0.039 in）
Rear rim：
0±1.0 mm（0±0.039 in）
- 273 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
Sun-roof adjustment
1.Remove sun-roof ornaments two fasteners
Sun-roof ornaments on left and right
sides must be firstly removed
before adjustment
Note：The ornaments will be repositioned
after adjustment
2. Upper and lower position adjustment
Tighten or Loosen bolts with torque screw
driver to regulate vertical separation
Clearance：0±2.0 mm （0±0.079 in）
3. Front and back side adjustment
Loosen the fixing nuts on sun-roof
and shift sun-roof bracket forward and
backward to adjust
As showed in the drawing：
Make link rod slide forward and
backward to align two marks
Slide by hand bracket to front
terminal
- 274 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
4. Left and right side adjustment
Loosen the fixing nuts at rear bearers on
sun-roof and shift sun-roof left and
right to adjust
5. Clearance adjustment
（clearance between left side and right
side）
Loosen fixing nuts to readjust sun-roof to
correct position
When assembling, the sequence is the reverse procedure of removal.
- 275 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
Chapter 17 Bumper
Remove front bumper
1. Remove baffle plates
（1）Loosen three fixing screws
（2）Loosen fixing screws and
remove fasteners with unfastening
tool
2. Remove splashers
（front-left and right）
（ 1 ） Loosen three fixinging screws on
splasher
（2）Detach three fasteners with
- 276 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
screw driver and unfastening
tool, and remove
cover sheet
3. Remove front grid
Loosen two fixing screws and
remove grid
4. Remove front bumper
（1）Loosen four fixing screws on
inner left and right sides
- 277 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
（2）Detach seven fasteners with
screw driver and unfastening tool
（3）Loosen the front screws beside the
wires of fog lamp and turn signal
light
5. Remove front fog light
Loosen two screws and
remove front fog light
6. Remove front turn signal light
Loosen fixing screws and remove
front turn signal light
- 278 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
7. Remove the grid
cover on front bumper
（1） Loosen four screws on upper
and lower sides
（2） Press down protecting fasteners
and get grid cover out
- 279 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
8. Remove the reinforcement
rods of front bumper（left and
right）
Loosen four screws on upper side
and take down the reinforcement
rods
Remove inner bumper
① Take down the bundle of fog light
② Loosen four fixing nuts on left and
right
and take down inner bumper
Remove rear bumper
① Loosen two fixing screws on left and right
( in boot )
② Loosen two cross recess head screws in tail part
- 280 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
③ Loosen four fixing screws on left and right
④ Loosen two set bolts on lower side
and tremove rear bumper
Remove the small bulb on
rear bumper
Loosen fixing screws and take down the
small bulb
When assembling, the sequence is the reverse procedure of removel.
- 281 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
Attachment：
Maintenance Specification Torque Norm
Fastened Parts N-m kgf-cm lbf-ft
engine hood - - -
hood hinge ×hood 11.5 115 8.3
hood lock×body 7.8 80 69 lbf-in
hood suport×hood 22 225 16
hood suport×body 22 225 16
front door - - -
power window×front door 5.5 56 49 lbf-in
door lock×front door 5.0 51 44 lbf-in
back door - - -
power window×back door 5.5 56 49 lbf-in
door lock×back door 5.0 51 44 lbf-in
trunk - - -
trunk hinge×trunk door 11.5 115 8.3
latch hole of trunk lock × - - -
trunk door 5.4 55 48 lbf-in
trunk door suport×trunk door hinge 22 225 16
windshield wiper×jet washer - - -
motor and link rod assembly of windshield wiper× 5.4 55 48 lbf-in
body
locating bolt for bar stay of auxiliary arm ×motor 5.4 55 48 lbf-in
and link rod assembly of windshield wiper
wiper arm and blade assembly×motor and link rod 22 225 16
assembly of winder screen wiper
seat - - -
front seat - - -
seat back assembly×seat cushion assembly 18 185 13
rear seat - - -
back of rear seat×car body 18 185 13
seat-belt - - -
front seat-belt - - -
shoulder belt clip×adjuster clip 43 440 32
outer seat-belt clip×front seat 43 440 32
seat-belt retractor assembly×body（upper） 7.8 80 69 lbf-in
seat-belt retractor assembly× body（lower） 43 440 32
inner front seat-belt×power seat regulator 43 440 32
manual seat regulator×body 43 440 32
rear seat-belt - - -
lower end of outer back seat-belt ×body 43 440 32
inner back seat-belt×body 43 440 32
- 282 – Chery Automobile Co.,Ltd
Chery QQ Service Manual
- 283 – Chery Automobile Co.,Ltd
