2

Contents

1. Introduction......................................................................... 4
2. Features ................................................................................ 6
3. Technical Specification ...................................................... 7
4. Measure of Appearance .................................................... 9
5. Front Panel ........................................................................ 10
6. Rear Panel ......................................................................... 14
7. How to Install .................................................................... 15
8. Calibration Mode ............................................................. 16
9. Set Mode ............................................................................ 24
10. Test Mode......................................................................... 43
11. Weighing Mode............................................................... 47
12. Serial Interface(COM1, COM2) ................................ 63
13. Options ............................................................................. 67

3
1. Introduction
Thank you for purchasing the CAS CI-6000A weighing indicator.
We have designed this equipment with many advanced features, high quality construction, and user-
friendly menu driven programming.
CAS indicator is shaped firmly and delicately designed to coincide with the special requirements of
several industrial fields and includes many functions and various external interfaces. Also, it contains
help display functions to be used easily.
Before using CI-6000A, It is recommended to read this manual carefully and to apply
the function application fully.

Precautions
Observe the following safety precautions :

Warning

When any damage or defect Insert plug firmly to wall outlet to Scale must be grounded to
occurs, contact your CAS prevent electric shock. minimize electricity static. This
authorized dealer immediately will minimize defect or electric
for proper repair. shock.

Do not pull the plug by its cord To prevent from fire occurring, To reduce electric shock or
when unplugging. Damaged Do not place or use the scale incorrect reading, Do not spill
cord could cause electric shock near flammable or corrosive water on the scale or place it in
or fire. gas. humid condition.

4
Avoid placing the scale near
heather or in direct sunlight.

Attention

For consistent and accurate Avoid sudden shock to the scale. Attach the rubber pad to the
reading, maintain periodical Internal mechanism could by bottom of the indicator.
check by your CAS authorized damaged. Elimination is possible.
dealer.

Place the scale on firm and Keep the scale away from the electromagnetic generation devices.
temperature consistent This may interfere with accurate reading.
environment.

Our Dealers :
CAS feels that each of its valued customers should get the best service
available.

Whether it’s the initial installation of our product, maintenance/repair work, or simply answering
questions about our products, CAS Corporation and all of its Authorized Dealers are highly trained to
assist you with any need regarding CAS products.

5
2. Features
1) Features
■ High speed, High accuracy
■ The adoption of high speed micro processor
■ A/D conversion speed : Maximum 200 times/sec
■ Appropriate for weighing and measurement system
■ Easy operation and various options
■ Simple and prompt Full Digital Calibration
(SPACTM : Single pass automatic span calibration)
■ RFI/EMI screened
■ WATCHDOG circuitry (System restoration)
■ WEIGHT BACK-UP
(Weight memory at sudden power failure)

2) Main Functions
■ Save date, time and calculated data at sudden power failure
■ Various specification of weight conversion speed
(Digital filter function)
■ Various printer connection (RS-232C Serial printer)
■ Tare weight setting with keys
■ Storage of measured times
■ Read / Write Set-point values(7) through the PC
- each to set-point code(0~49)
■ Read / Write Set Mode values(23) through the PC
■ External 6 relays for input / 8 relays for output
■ Users can set the max. weight and a division freely
■ Control various external equipment by inner external input/output
■ Print date and time by built-in clock
■ Self hardware test.

6
3. Technical Specification
■ Analog Part & A/D Conversion

Load Cell Excitation Voltage 8 x 350Ω load cells

Zero Adjustment Range 0.05mV ∼ 20mV
Input Sensitivity 0.6μV/D
System Linearity Within 0.01％ of FS.
A/D Internal Resolution 1 / 1,000,000
A/D External Resolution 5,000 dd, 10,000 dd (Max)
A/D Conversion Speed Maximum 200 times/sec

■ Digital Part
Full Digital Calibration : SPAC™
Span Calibration
(Single pass automatic span calibration)
Input Noise Under ±0.3μVpp
Input Impedance Over 10M Ω
Display VFD (7 digit)
Size of letter 13mm (Height)
Minimum division x1, x2, x5, x10, x20, x50
Display below zero “-”

"ZERO" ▼ Current weight of “0” kg

"STABLE" ▼ Weight is stable

"GROSS" ▼ Gross weight is displayed

"NET" ▼ Net weight is displayed

"TARE" ▼ Tare function is activated

"HOLD" ▼ Hold function is activated

" * " key is pressed (print key)
"*" ▼
Automatic print is set.

7
■General Specification

AC 100 ~ 240V (50/60 Hz) Input

DC +3.3V Digital Logic

Power DC +24V External I/O

DC +5V Analog, Load Cell

AC 3.6V VFD

Product Size 192(W) x 189(D) x 96 (H)

Temperature Range -30℃ ~ +60℃

Product Weight Approx. 2.4 kg

8
4. Measure of Appearance

9
5. Front Panel
1) VFD Display

■ Display Lamp(▼)

ZERO lamp Current weight is 0 kg

ST lamp Weight is stable

GROSS lamp Current weight is gross weight

NET lamp Current weight is net weight

TARE lamp Tare weight is saved

HOLD lamp Lamp is on when HOLD function is activated

Lamp is on only when “*” key is pressed. And F23 is
set to “1” in the set mode
* lamp
Automatic print should be set to “1” in set mode
(F41 = 1 or 2, F42 = 1)

10
2) Keyboard

You can use these keys as numeric keys

Change the set value

key increases set value and key decreases set
value
Change the position of cursor
key moves one digit to right, key moves one digit
to left
Use 1 Enter tare weight

Use 2 Enter set-point value

Use 3 Enter the set value in TEST, CAL, SET mode

■ [ ZERO ]Key
Used to remove small variations in the indicator’s zero

■ [ TARE ] Key
Used to weigh an item by using the container
Current weight is memorized as tare weight
If you press TARE key in unload condition, tare setting is released

■ [ KEY TARE ] Key

When you already know the tare weight, press KEY TARE Key
and enter tare weight by pressing arrow keys and save it by pressing ENTER key

■ [ G/N KEY ] Key

Toggles the display between gross and net weight
G. weight lamp on - gross weight / N. weight lamp on - net weight
If tare weight is saved, tare plus item's weight is gross weight and only item's weight is net weight
You can prohibit using of keyboard by pressing G/N key for 5 sec.
To use keyboard again, press G/N key for 5 sec

11
■ [ * KEY ]Key
Used to set set-point value for batching operation.
(Press * key for 3 seconds more and take off)
You can select this function in set mode F23
0 : Do not use.
1 : PRINT Key.
2 : HOLD Key

■ [ ENTER KEY ] Key

Set set-point code for batching operation.(00~49)
(Press the ENTER key for 3 seconds more and take off)
You can select this function in set mode F24.
0 : Do not use.
1 : TOTAL PRINT key.
2 : START key for batching operation.
3 : STOP key for batching operation.
In calibration, test, set mode : Save current condition and exit

12
3) Slide Switch

Calibration mode

SW1 DIP 1 Switch DIP 1 on Go to calibration mode

Switch DIP 1 off After calibration, it returns to weighing mode

Set mode

SW1 DIP 2 Switch DIP 2 on Go to set mode.

Switch DIP 2 off After set mode, it returns weighing mode.

Test mode

SW1 DIP 3 Switch DIP 3 on Go to test mode.

Switch DIP 3 off After test, it returns to weighing mode

It is used in calibration mode when zero value is high

SW2 DIP 1
If you set DIP 1 to on, zero value is decreased.

It is used in calibration mode when zero value is low

SW2 DIP 2
If you set DIP 2 to on, zero value is increased

13
6. Rear Panel

OPTION
AC

LOADCELL

T250mA
L250V

COM2 COM1 CONTROL I/O

RS-232 cable( 2 : TxD, 3 : RxD, 5,7 : Gnd )

- F33 = 1 ~ 4 function is enable (both of Set-point and Set-
COM1
mode) to read and write
- Computer, sub-display and printer
RS-232 cable( 2 : TxD, 5,7 : Gnd)
- F36 = 1 ~ 2 function is enable to read only
COM2
RS-485/422 cable( 6 : Rx+, 7 : Rx-, 8 : Tx+, 9 : Tx- )
- F36 = 1 ~ 4 function is enable(Set-point) to read and write
LOAD CELL Port for connecting. 4-wires, 6-wires load cell
External
ZERO, TARE,START,STOP,*,ENTER key
input
CONTROL I/O
External
External output for batching operation
output
OPTION When option is used, please connect

AC 100 ~ 240VAC are available

FUSE T250mA L250V

14
7. How To Install
1) Load cell connection
Connect load cell connector to load cell port which is in the backside CI-6000A
* Connecting method

PIN
1 (EXC+)
2 (SEN+)
3 (EXC-)
4 (SEN-)
5 (SIG+)
6 (SIG-)
7 (SHIELD)

Note 1. In case of 4 wires L/C connect EX+ with SEN+, and connect EX- with SEN-.

Note 2. Wire color can be different depending on the load cell’s manufacturer or its model

2) Power
Adjusted to 220V 50/60Hz at factory.
(If you want to use 110V, adjust 110V/220V jump wire which is located
in the inner part of CI-6000A)

15
8. Calibration Mode
1) How to enter the Calibration Mode.
Open the front cover of indicator and set SW1 DIP1 to on.
At this time, message is shown on the display and is started.
After done and off the SW1 DIP1, back to the weighing mode.

2) Availabe keys.
KEY : Change the set value.
key increases set value and key decreases set value.

KEY : Change the position of cursor.

key moves one digit to right, key moves one digit to left.

ENTER KEY : The program is moved into next menu.

3) Calibration menu(CAL1~CAL7)
CAL 1 : Maximum capacity
CAL 2 : Minimum division
CAL 3 : Setting Weight
CAL 4 : Zero calibration
CAL 5 : Span calibration
CAL 6 : Check Micro Span calibration
CAL 7 : Weight Factor

16
CAL 1

FUNCTION : Maximum Capacity Set (Range : 1 ~ 99,999)

KEY DISPLAY DESCRIPTION

: C = 05000 5000 kg
Increase or decrease
of number
:
C = 0500.0 500.0 kg(First decimal point)
Shift of cursor position
ENTER :
Save and go to next
menu C = 050.00 50.00 kg (Second decimal point)

Note 1. The maximum capacity means the maximum weight of the indicator.
Note 2. The max. weight is changed depending on the decimal point.

CAL 2

FUNCTION : Minimum Division Set (Range : 0.001 ~ 50)

KEY DISPLAY DESCRIPTION
: d=1 1 kg
Increase or decrease
of number d = 0.2 0.2 kg (First decimal point)
ENTER :
Save and go to next d = 0.05 0.05 kg (Second decimal point)
menu
d = 0.001 0.001 kg (Third decimal point)

Note 1. The minimum division means the value of one division.

Note 2. The value of one division is changed depending on the decimal point.
Note 3. External resolution is obtained by dividing the maximum capacity into the min. division.
Set the resolution to be within 1/10,000.
If it is over 1/10,000, error message "Err 20" is displayed

17
CAL 3
FUNCTION : Setting Weight In Span CALIBRATION
KEY DISPLAY DESCRIPTION

:
Increase or decrease L=05000 5000 kg
of number
:
Shift of cursor position
ENTER :
Save and go to next L=0500.0 500.0 kg (First decimal point)
menu

Note 1. The setting weight should be within the 10 % to 100 % of maximum weight
100% of maximum weight is set as a default but you can change it for your needs
If the setting weight is under 10%, error message "Err 22" is displayed
If the setting weight is over 100%, error message "Err 23" is displayed

CAL 4
FUNCTION : Zero Calibration
KEY DISPLAY DESCRIPTION

ENTER : Remove an item from the platter

Zero calibration and and press ENTER key.
CAL 4
next
Analog value of Zero calibration.
ZERO : load weight state
Only zero calibration Zero calibration is finished.
--- You will go to span
TARE : calibration(CAL 5)automatically.
Only span calibration

Note 1. If Zero calibration is done without any error, You will go to span calibration (CAL 5)
automatically.
Note 2. If the zero value is too low, error message "Err 27" is displayed.
Note 3. If the zero value is too high, error message "Err 26" is displayed.
Note 4. If you want to do only zero calibration, unload the platter and press the "ZERO" key.
In a few moment, you will see "ZEro" and "CAL End" messages are displayed.
Set SW1 DIP1 to OFF and then return to the weighing mode.

18
CAL 5

FUNCTION : Span Calibration

KEY DISPLAY DESCRIPTION
Load the weight which was set in
CAL 5 CAL 3 and press ENTER key.

ENTER : Analog value of Span calibration.

Span calibration load weight state
Span calibration is finished.
--- You will go to micro span
calibration(CAL 6) automatically.

Note 1. If span calibration is done without any error,

you will go to micro span calibration (CAL 6) automatically.
Note 2. If the span value is low,
error message "Err 24" is displayed. Calibrate with lower resolution.
Note 3. If the span value is high, error message "Err 25" is displayed.

CAL 6

FUNCTION : Check Micro Span Calibration

KEY DISPLAY DESCRIPTION
Setting weight is shown on the
500.0
display.
ENTER : Save and
go to next menu Check the setting weight and set
▽▽▽▼▽▽▽
SW1 DIP1 to off.

Note 1. Confirm if the displayed weight is equal to the setting weight that you have
set in CAL 3 and remove the weight from the platter.
If "0" is displayed, set SW1 DIP1 to OFF then you will go to normal mode.
Note 2. The bias is "0" when the central lamp lights up as above display.
Each lamp means the bias of -0.3, -0.2, -0.1, 0, 0.1, 0.2, 0.3 from the left lamp

19
CAL 7

FUNCTION : Weight Constant Calibration

KEY DISPLAY DESCRIPTION
:
Enter password.
FACtor Enter password.
ENTER : Exit

Note 1. Users do not have to use this menu, since it is used for calibration test without a
weight.

20
4) Error Message (In CAL Mode)
Error 20
▣ Reason
The resolution exceeds 1/10,000
☞ Solution
Lower the resolution.
The resolution = allowed weight/one division.
Modify the allowed weight in CAL1 or modify the division in CAL2 so that
the resolution is below 1/10,000

Error 22
▣ Reason
The weight for span calibration is lower than 10% of the maximum
capacity of the indicator
☞ Solution
Set the weight for span calibration in CAL 3 to be greater than 10% of the
maximum capacity

Error 23
▣ Reason
The weight for span calibration exceeds 100% of the maximum capacity
of the indicator
☞ Solution
Set the weight for span calibration to be within the maximum capacity of
the indicator in CAL 1

Error 24
▣ Reason
Span value is too low
☞ Solution
Load cell is damaged or setting of current resolution is not possible.
Calibrate with less resolution

21
Error 25
▣ Reason
Span value is too high
☞ Solution
Load cell is damaged or setting of current resolution is not possible.
Calibrate with less resolution

Error 26
▣ Reason
Zero value is too high
☞ Solution
Check whether the platter is empty
Remove the setting cover and set SW2 DIP2 to on so that the zero value is
increased. Proceed calibration again after checking in test mode 3

Error 27
▣ Reason
Zero value is too low
☞ Solution
Check whether the platter is empty.
Remove the setting cover and set SW2 DIP1 to on so that the zero value is
decreased. Proceed calibration again after checking in test mode 3

Error 28
▣ Reason
The weight is unstable
☞ Solution
Check whether load cell is properly connected

22
5) Sealing Method
① Sealing method of cal switch

② Sealing method of Load Cell Connector

23
9. Set Mode
1) How to go to set mode
Open the front cover of indicator. set SW1 DIP2 to on. Then set mode is started.
At this time, F01 message is shown on the display after “SET Mod” message.

① : You can select the menu that you want to set

② Enter number of set menu by pressing the arrow keys and then press ENTER key.
③ : F01 is set to 1.
④ Enter number of set menu by pressing the arrow keys and then press ENTER key.

2) Availabe keys.
KEY : Change the set value.
key increases set value and key decreases set value.

KEY : Change the position of cursor.

key moves one digit to right, key moves one digit to left.

ENTER KEY : Save current setting value and go to menu selection mode.

3) Set Menu(F01~F59)

General setting
F01 Decimal Point Adjustment
F02 Weighing Unit
F03 Analog to Digital Conversion Speed
F04 Digital Filter
F05 Motion Detection Condition
F06 Automatic Zero Tracking Compensation
F07 Weight Backup
F08 Set Zero Range
F09 Conditions of ZERO, TARE & START Keys
F10 Set Hold Type

24
Batching Operation Function
F11 Zero Band
F12 Optional Preliminary Weight
F13 Preliminary Weight
F14 Final Weight
F15 Free Fall Weight
F16 High Limit Weight
F17 Low Limit Weight
F18 Timer - Start Delay Time
F19 Timer - Operating Delay Time of Finish Signal
F20 Measurement Mode
F21 Timer - Start Delay Time of Finish Signal
F22 Off Range of Finish Signal

F23 A Use of "*" key

F24 A Use of ENTER key

Serial Interface (COM1, COM2)

F30 Device ID
F31 COM1 Baud Rate
F32 COM1 Usage
F33 COM1 Output Mode
F34 COM2 Baud Rate
F35 COM2 Usage
F36 COM2 Output Mode
F37 Output Format of COM1 & COM2
F38 Parity Bit

Print Function
F40 Line Feed
F41 Printer
F42 Automatic / Manual Print
F43 Printing Format

25
 F44 Output the user’s message
F45 Date Change
F46 Time Change

User’s Utility
F50 Set-point input type selection
F51 Load cell type selection
F52 Buzzer On/Off selection

Options
Select the Option
Analog Out (Option -1) : 4~20mA
F55 Analog Out (Option -2) : 0~10V

BCD Out (Option -3) :

F56 Output Logic of BCD Out
F57 Analog Output Adjustment at Display Zero
F58 Analog Output Adjustment at Maximum Capacity

F01 ~ F03
F05 ~ F10
F18 ~ F24
F40 ~ F43
F50 ~ F52
These items of SET MODE are possible to be red & written from PC (Set Mode Values)

F11 ~ F17
These items of SET MODE are possible to be red & written from PC (Set Mode Values)

26
① General function
F01

FUNCTION : Decimal Point Adjustment

DISPLAY DESCRIPTION
F01 0 No Decimal Point (ex : 12345)
1
Set value F01 1 10 (ex : 1234.5)
(0~3)
2
F01 2 10 (ex : 123.45)
3
F01 3 10 (ex : 12.345)

F02

FUNCTION : Weighing Unit

DISPLAY DESCRIPTION
Set value
F02 0 Kilogram (kg)
( 0, 1 )
F02 1 Ton (t)

F03

FUNCTION : A/D Conversion Speed

DISPLAY DESCRIPTION DISPLAY DESCRIPTION
F03 0 20 times/sec. F03 5 120 times/sec.

Set value F03 1 40 times/sec. F03 6 140 times/sec.

(0~9) F03 2 60 times/sec. F03 7 160 times/sec.
F03 3 80 times/sec. F03 8 180 times/sec.
F03 4 100 times/sec. F03 9 200 times/sec.

F04

FUNCTION : Digital filter

DISPLAY DESCRIPTION
Set value F04 10 10 time average value
( 00 ~ 99 ) F04 50 50 times average value
F04 99 99 times average value

Note 1. Adjust the set value according to the condition.

27
F05

FUNCTION : Motion Detection Condition

DISPLAY DESCRIPTION
Stable lamp is off even with the change of only 1 division for 1
F05 12
Set value sec.
( 00 ~ 99 ) Stable lamp is on with changing of the weight below 5 division
F05 56
for 3sec.
Stable lamp is on with changing of the weight below 8 division
F05 88
for 4sec.

Note 1. The first digit indicates division and the second digit indicates sec.
but have to divide it into 2 on the display.
F06

FUNCTION : Automatic Zero Tracking Compensation

DISPLAY DESCRIPTION
F06 0 None
Set value F06 1 0.5 digit
(0~9) Auto-zero tracking will remove small
variations automatically
F06 5 2.5 digit

F06 9 4.5 digit

F07

FUNCTION : Weight backup

DISPLAY DESCRIPTION
Set value
F07 0 Weight backup is OFF
(0,1)
F07 1 Weight backup is ON

Note 1. Memorize the current weight at sudden power failure.

F08

FUNCTION : Set Zero Range

DISPLAY DESCRIPTION
Set value F08 0 Zero key is operated within 2% of max. weight
( 0, 1 )
F08 1 Zero key is operated within 10% of max. weight

28
F09

FUNCTION : ZERO, TARE & START keys Availability

DISPLAY DESCRIPTION
Set value
F09 0 Always
(0,1)
F09 1 Works when weight is stable

F10
FUNCTION : Set Hold Type
DISPLAY DESCRIPTION
Average hold :
F10 0
Compute the average weight of oscillating weights
Set value Peak hold :
(0~2) F10 1 Compute the maximum weight among oscillating
weights
Sampling hold :
F10 2
Compute the moment weight of oscillating weights.

Note 1. You have to set F23 to 2 in set mode.

Note 2. The hold function is released when it is in zero range or over load automatically.

② Batching operation function

F11

FUNCTION : Zero Band

Set zero band value which will be used in batching operation

F12

FUNCTION : Optional Preliminary Weight

Set optional preliminary weight which will be used in batching operation

F13

FUNCTION : Preliminary Weight

Set preliminary weight which will be used in batching operation

F14

FUNCTION : Final Weight

Set final weight which will be used in batching operation

29
F15

FUNCTION : Free Fall Weight

Set free fall weight which will be used in batching operation

F16

FUNCTION : High Limit Weight

Set high limit weight which will be used in batching operation

F17

FUNCTION : Low Limit Weight

Set low limit weight which will be used in batching operation

F18

FUNCTION : Timer – Start Delay Time

DISPLAY DESCRIPTION
Set value F18 00 No delay
( 00 ~ 99 ) F18 01 0.1 sec
F18 99 9.9 sec

F19

FUNCTION : Timer – Operating Delay Time of Finish Signal

DISPLAY DESCRIPTION
F19 00 Do not use
Set value
( 00 ~ 99 ) F19 10 1.0 sec

F19 99 9.9 sec

Note 1. This function is used to decide the time of signal output which batching operation is
completed.
Note 2. You have to set F19 to 00 if you want to use the F22 function.
If F19 & F22 are set any values at the same time, F22 is disregarded.
Because the priority of F19 is high.

30
F20

FUNCTION : Measurement Mode

DISPLAY DESCRIPTION
F20 0 Do not use.
F20 1 Customer Programmed Normal batching
Set value
(0~4) F20 2 Control mode Loss-in-Weight batching

F20 3 Built-in automatic Normal batching

Program mode
F20 4 Loss-in-Weight batching

F21

FUNCTION : Timer – Start Delay Time of Finish Signal

DISPLAY DESCRIPTION
F21 00 No delay time
Set value
( 00 ~ 99 ) F21 10 1.0 sec

F21 99 9.9 sec

Note 1. This function is used to decide the delay time of start- signal of output which the batching
operation is completed

F22

FUNCTION : Off Range of Finish Signal

DISPLAY DESCRIPTION
F22 00 Do not use
Set value
( 00 ~ 99 ) F22 01 Finish signal is off when the weight is within one division
Finish signal is off when the weight is within ninety nine
F22 99
division

Note 1. This function is used to decide the size of output signal which batching- operation is
completed.
Note 2. You have to set F19 to 00 if you want to use the F22 function.
If F19 & F22 are set any values at the same time, F22 is disregarded.
Because the priority of F19 is high

31
F23

FUNCTION : A Use of “*” key

DISPLAY DESCRIPTION
F23 0 Do not use
Set value
(0~2) F23 1 PRINT key

F23 2 HOLD key

Note 1. It is possible to print key (COM1 only) when the usage of COM2(F35) is to set 0.
(F35 = 0). That is, F35 is setting to printer.

F24

FUNCTION : A Use of “ENTER” key

DISPLAY DESCRIPTION
F24 0 Do not use
Set value F24 1 TOTAL PRINT key
(0~2)
F24 2 START key in batching operation

F24 3 STOP key in batching operation

Note 1. It is possible to print key (COM1 only)

③ Serial Interface (COM1, COM2 )

Reference

RS-232C Cable
Connector Print Key(F23=1,F24=1) Comm. Spec. Command
COM1(2,3,5&7) To be set F35 = 0 TxD, RxD Read/Write
Stream,
COM2(2,5&7) TxD Read
Transmit weight when it is stable

RS-422/485
Connector Print Key(F23=1,F24=1) Comm. Spec. Command
COM2(6,7,8,9) To be set F35 = 0 TxD, RxD Read/Write

32
F30

FUNCTION : Device ID
DISPLAY DESCRIPTION
Set value
F30 01 Device No. 01
( 00 ~ 99 )
F30 99 Device No. 99

Note 1. It is used for identification of the indicator when system is connected.

F31

FUNCTION : Baud Rate of COM1

DISPLAY DESCRIPTION
F31 0 600 bps
F31 1 1200 bps
Set value
F31 2 2400 bps
(0~5)
F31 3 4800 bps
F31 4 9600 bps
F31 5 19200 bps

F32

FUNCTION : A Use of COM1

DISPLAY DESCRIPTION
Set value
F32 0 Connection with sub-display or computer
( 0 ,1 )
F32 1 Connection with printer

33
F33

FUNCTION : Output Mode of COM1 (RS-232)

DISPLAY DESCRIPTION
F33 0 No data output
F33 1 Stream mode
Set value Transmit one time only in stable condition after
(0~4) F33 2
Unloading to zero
Transmit when data is required
F33 3
* Signal : device ID (F31 : Device ID)
F33 4 Command Mode

Note 1. in the case of F33=3, if the Device ID is “01”, send to the “01” in the hexa mode in the
RS232C Simulator or “ALT”+”1” in the Hyper Terminal.

Note 1 : COM 1 : F33 = 4, COM2 : F35 = 1, F36 = 4 Command Mode

Command to CI-6000A Command
Indicator to PC
0 1 2 3 4 5 6 7 8 9 10 11 description
D ID K Z CR LF ZERO key Return the received
D ID K T CR LF TARE key Return the received
D ID K G CR LF GROSS key Return the received
D ID K N CR LF NET key Return the received
D ID K S CR LF START key Return the received
D ID K P CR LF STOP key Return the received
D ID K B CR LF Print key Return the received
D ID K C CR LF Total print key Return the received
D ID K W CR LF Request weight data Return the received
D ID H T CR LF Request set-point SEND Format 2
D ID H Z 0 0 0 0 0 CR LF Zero band Return the received
D ID H O 0 0 0 0 0 CR LF Optional pre. Return the received
D ID H P 0 0 0 0 0 CR LF Preliminary Return the received
D ID H F 0 0 0 0 0 CR LF Final weight Return the received
D ID H R 0 0 0 0 0 CR LF Free fall weight Return the received
D ID H I 0 0 0 0 0 CR LF High limit weight Return the received
D ID H L 0 0 0 0 0 CR LF Low limit weight Return the received
D ID H E 0 0 0 0 0 CR LF Set-point code Return the received
D ID S T CR LF Set Mode Value SEND Format 4

34
(D, ID : 00~99, CR:0x0d, LF:0x0a)
It is impossible to test with Print Key ( + Total Sum Print Key) ( Only possible when F35 = 0)

■ Format 1 [ Set Point Write :: COM1/COM2 Port available ]

Write the Set-Point values to the CI-6000A with PC
- Writing(Command) & Response Format
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

D ID H A Set Point Code , Zero Band ,

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
Opt. Preli, Weight , Preliminary Weight , Final Weight
34 35 36 37 38 39 40 41 42 43 44 45 46
, Free Fall Weight , Hi Limit Weight ,
47 48 49 50 51 52 53

Lo Limit Weight CR LF
Note 1 : When you input the Set Point Value, you have to input without decimal point

■ Format 2 [ Set Point Read :: COM1/COM2 Port available ]

Read the Set-Point values from CI-6000A with PC
- Command Format
0 1 2 3 4 5 6
D ID H T CR LF

- Response Format
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

D ID H T Set Point Code , Zero Band ,

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
Opt. Preli, Weight , Preliminary Weight , Final Weight
34 35 36 37 38 39 40 41 42 43 44 45 46
, Free Fall Weight , Hi Limit Weight ,
47 48 49 50 51 52 53

Lo Limit Weight CR LF
Note 1 : All of Set Point Values are numeric without decimal point.

35
■ Format 3 [ Set Mode Write :: COM1 Port only ]
Write the Set-Mode values [F01~F10, F18~F24, F40~F43, F50~F52]
from CI-6000A with PC
- Writing(Command) & Response Format
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

D ID S F F01 F02 F03 F05 F06 F07 F08 F09 F10

15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
F18 F19 F20 F21 F22 F23 F24 F40 F41 F42 F43
30 31 32 33 34
F50 F51 F52 CR LF

■ Format 4 [ Set Mode Read :: COM1 Port only ]

Read the Set-Mode values from CI-6000A with PC
- Command Format
0 1 2 3 4 5 6
D ID S F CR LF

- Response Format
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

D ID S F F01 F02 F03 F05 F06 F07 F08 F09 F10

15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
F18 F19 F20 F21 F22 F23 F24 F40 F41 F42 F43
30 31 32 33 34
F50 F51 F52 CR LF

36
F34

FUNCTION : Band Rate of COM2

DISPLAY DESCRIPTION
F34 0 600 bps
F34 1 1200 bps
Set value
F34 2 2400 bps
(0~5)
F34 3 4800 bps
F34 4 9600 bps
F34 5 19200 bps

F35

FUNCTION : Usage of COM2

DISPLAY DESCRIPTION
Set value
F35 0 Connection with printer
( 0 ,1 )
F35 1 Connection with sub-display or computer

F36

FUNCTION : Output Mode of COM2 (RS-232, RS-422/485)

DISPLAY DESCRIPTION
F36 0 No data output
F36 1 Stream mode RS-232,RS-422/485
Set value Transmit one time only in stable
F36 2 RS-232,RS-422/485
(0~4) condition after Unloading to aero
Transmit when data is required
F36 3 * Signal : device ID RS-422/485
(F31 : Device ID)
F36 4 Command Mode RS-422/485

Note 1. COM2 connector of rear plate have two mode. One is a RS-232(F36=1, 36=2) mode.
Another is a RS-422/485 (F36=1 ~ F36=4).
Note 2. in the case of F36=3, if the Device ID is “01”, send to the “01” in the hexa mode in
the RS232C Simulator or “ALT” + “1” in the Hyper Terminal.

37
F37
FUNCTION : Output Format of COM1 and COM2
DISPLAY DESCRIPTION
Set value F37 0 Transmit 22 byte of CAS Format
(0~2) F37 1 Transmit 10 byte of CAS Format
F37 2 Transmit 18 byte of AND Format

F38
FUNCTION : Parity Bit
DISPLAY DESCRIPTION
Set value F38 0 Data bit 8, Stop bit 1, Non parity
(0~2) F38 1 Data bit 7, Stop bit 1, Even parity
F38 2 Data bit 7, Stop bit 1, Odd parity

④ Printer Function
F40
FUNCTION : Line Feed
DISPLAY DESCRIPTION
Set value
F40 1 1 Line feed
(1~9)
F40 9 9 Line feed

F41
FUNCTION : Printer
DISPLAY DESCRIPTION
Set value F41 0 Do not use
(0~2) F41 1 CAS TOP printer (P202)
F41 2 CP-7000 Series Printer (CP-7000D/P, CP-7024P)

F42
FUNCTION : Automatic / Manual Print
DISPLAY DESCRIPTION
Set value
F42 0 Manual print
(0~1)
F42 1 Automatic print

Note 1. If .F42 is set to 1, printing is done without pressing PRINT key.

It is possible to print again only after the weight is returned to zero (unload)

38
F43

FUNCTION : Printer Format

DISPLAY DESCRIPTION
Set value F43 0 Printing format 0
(0~2) F43 1 Printing format 1
F43 2 Printing format 2

【 Form 0 】 【 Form 1 】 【 Form 2 】

Date, Time Date, Time Date, Time
Serial No., Net weight Serial No., Net weight Gross weight, Tare weight,
Tare weight

02. 1. 1 12:30
02. 1. 1 12:30 Gross : 1000.0 kg
001, 50.0 kg Tare : 0.0 kg
02. 1. 1 12:30 02. 1. 1 12:40 Net : 1000.0 kg
001, 50.0 kg 002, 50.0 kg 02. 1. 1 12:40
002, 100.0 kg 02. 1. 1 12:50 Gross : 2000.0 kg
003, 200.5 kg 003, 50.0 kg Tare : 500.0 kg
Net : 1500.0 kg
----------------------------------- ----------------------------------- -----------------------------------
TOTAL 350.5kg TOTAL 150.0kg Net TOTAL 2500.0kg

Note 1. The serial number is initialized to 001 after total printing or power off and on.

F44

FUNCTION : Input user's Information to Printing Format

Used key DISPLAY DESCRIPTION
: th
Data P12-065 Set ‘A’ (ASCII code 65) in 12 data
Designation * Set blank to 0th character
key : P00-032
This 0th code decides to print dead message.
Increase Set 255 to 18th character.
coordinate P18-255
This code indicates the end of data to be printed.

Note 1. You can add user’s information in printing format.

(Ex : Company name, phone no.)
Note 2. The range of coordinate is from 0 to 71. 0th code determines whether head message is
printed or not.(032 : print, others : Do not print) Actually 1st data to 255 is printed.
Note 3. Designate as follows if you want to add company name “CAS” on print format.
P00-032( ASCII code 32 : Data start), P01-067( ASCII code 67 : character C)

39
 P02-065( ASCII code 65 : character A),P03-083( ASCII CODE 83 :character S)
P04-255( ASCII code 255: Data end)

Note 4. ASCII code table

CHA CODE CHA CODE CHA CODE CHA CODE CHA CODE CHA CODE

SPACE 32 0 48 @ 64 P 80 ` 96 p 112

! 33 1 49 A 65 Q 81 a 97 q 113

“ 34 2 50 B 66 R 82 b 98 r 114

# 35 3 51 C 67 S 83 c 99 s 115

$ 36 4 52 D 68 T 84 d 100 t 116

% 37 5 53 E 69 U 85 e 101 u 117

& 38 6 54 F 70 V 86 f 102 v 118

‘ 39 7 55 G 71 W 87 g 103 w 119

( 40 8 56 H 72 X 88 h 104 x 120

) 41 9 57 I 73 Y 89 i 105 y 121

* 42 : 58 J 74 Z 90 j 106 z 122

+ 43 ; 59 K 75 [ 91 k 107 { 123

, 44 < 60 L 76 \ 92 l 108 | 124

- 45 = 61 M 77 ] 93 m 109 } 125

. 46 > 62 N 78 ^ 94 n 110 ~ 126

/ 47 ? 63 O 79 _ 95 o 111 END 255

F45

FUNCTION : Date Change

KEY DISPLAY DESCRIPTION
key 02.01.10 JAN. 10TH, 2002
: Enter Data

F46

FUNCTION : Time Change

KEY DISPLAY DESCRIPTION
key 11.30.10 11 : 30 : 10 AM
: Enter Data

40
⑤ User’s utility
F50

FUNCTION : Set-point Input

DISPLAY DESCRIPTION
Set value
F50 0 Disable external Set-point input
(0,1)
F50 1 Enable external Set-point input

F51

FUNCTION : Load cell type

DISPLAY DESCRIPTION
Set value
F51 0 Compression or Tension Load cell ( 0mV ~ +40mV)
(0,1)
F51 1 Compression and Tension Load cell (-- 20mV ~ +20mV)

F52

FUNCTION : Buzzer On/Off

DISPLAY DESCRIPTION
Set value
F52 0 Always Buzzer is ON.
(0,1)
F52 1 Always Buzzer is OFF.

41
⑥ Options
F55

FUNCTION : Select of Option

DISPLAY DESCRIPTION
Set value F55 0 Do not use
(0,2) F55 1 Analog Out(Option – 1,2)
F55 2 BCD Out(Option – 3)

F56

FUNCTION : Output Logic – BCD Out

DISPLAY DESCRIPTION
Set value
F56 0 Positive Logic
(0,1)
F56 1 Negative Logic

F57

FUNCTION : Analog Output Adjustment at Display Zero

DISPLAY DESCRIPTION
Set value L 00000 0mA, 0V
( 0~4000 ) L 04000 4.000mA, 2V
L 04015 4.015mA, 2.007V

F58

FUNCTION : Analog Output Adjustment at Maximum Capacity

DISPLAY DESCRIPTION
Set value H 10000 10mA, 4.16V
( 0~24000 ) H 20000 20.000mA, 8.33V
H 24000 24.000mA, 10V

42
10. Test Mode
1) How to go to Test Mode
Open the front cover of indicator. set SW1 DIP3 on.

① : Select test menu that you wish to test.

② Please select test menu with arrow keys and press ENTER key.
③ : Test menu is selected. Proceed key test.
④ When test is done, Press ENTER key.

To finish test mode, set DIP3 off.

2) Test Menu (TEST 1 – TEST 8)

TEST 1 : Key test

TEST 2 : VFD display test
TEST 3 : A/D conversion test
TEST 4 : Serial interface test (COM1, COM2)
TEST 5 : Printer test (COM2)
TEST 6 : External input/output test
TEST 7 : Analog Out Test(Option)
TEST 8 : BCD Out Test(Option)

TEST 1

FUNCTION : Key test

KEY DISPLAY DESCRIPTION
ENTER: Go to menu tESt 1 TEST 1 condition
Selection mode
Press any key to test then the display
Other keys : Perform test 1 1
shows its number and code.

Note 1. External input key test is TEST 6.

< Key list >

KEY NO. CODE KEY NO. CODE KEY NO. CODE

ZERO 1 1 TARE 2 2 K.T 3 3

G/N 4 4 * 5 5 ENTER 6 6

43
TEST 2

FUNCTION : Display test

KEY DISPLAY DESCRIPTION
ENTER: Go to menu tESt 2 TEST 2 condition
Selection mode
Other keys : Perform test 8888888 TEST 2 is performed

TEST 3

FUNCTION : A/D Conversion test

KEY DISPLAY DESCRIPTION
: Change gain.
tESt 3 TEST 3 condition
: Change filter
ENTER: Go to menu Shows digital value of current weight.
Selection mode 97853
This value means converted digital value.

Note 1. Check whether digital value is changing. If the digital value is fixed or zero is
displayed, please check the connection of load cell.

TEST 4

FUNCTION : RS-232C test with computer (COM1)

KEY DISPLAY DESCRIPTION
: Transmit to PC tESt 4 TEST 4 condition
after increasing
value. 00------00 Wait for transmission and reception
: Transmit to PC
after increasing 03------00 Transmit : 3, Receive : none
value
ENTER: Go to menu 08------49 Transmit : 8, Receive : 1
Selection mode

Note 1. Do this test in Hyper Terminal of PC after the connecting serial port with PC.
- Port Selection in Hyper Terminal has the Flow Control item, you have to set nothing.
Note 2. Send no.1 in computer keyboard and check if indicator receives no.49
Send no.8 in indicator key( ) and check if computer receives no.8
Note 3. Baud rate should be specified in SET mode before testing.(F31)

44
TEST 5

FUNCTION : Printer test (COM1)

KEY DISPLAY DESCRIPTION
ENTER: Go to menu tESt 5 TEST 5 condition
Selection mode
Other keys : Perform test Good No error in printer.

Note 1. Please set F35 to 0 in SET mode.

Note 2. Please set F41(the kind of printer) in SET mode.
Note 3. “Good” message is displayed if the printer connection is done correctly.
Note 4. The test output format of printer is as follows:

Computer Aided System

CAS Corporation
TEL 82-2-2225-3500
FAX 82-2-475-4668
TEST OK

TEST 6

FUNCTION : External input /output test

KEY DISPLAY DESCRIPTION
: Move external
tESt 6 TEST 6 condition
Output
External input : In1 : If you press 1, 1 is displayed
Shows external key oUt3 : Indicate the condition of external
ENTER: Go to menu In1oUt3
output.
Selection mode Output no.3 is On.

45
TEST 7

FUNCTION : Analog Output Test

KEY DISPLAY DESCRIPTION

: Output high value tESt 7 TEST 7 condition

(20mA)
: Output high value Hi Lo ▲(Hi) (Lo) ▼
(20mA) HiGH : Output maximum weight.
ENTER: Go to menu HiGH
(Adjust to 20mA)
Selection mode ZEro : Output zero value
Zero
(Adjust to 4mA)

TEST 8

FUNCTION : BCD Output Test

KEY DISPLAY DESCRIPTION
: All output is ON
tESt 8 TEST 8 condition
: All output is OFF
ALL ON The state of All Output is ON (Defult)
ENTER: Go to menu
ALL OFF The state of All Output is OFF
Selection mode

46
11. Weighing Mode
1) How to move
Turn POWER switch on, and you will go to the Weighing Mode.

2) Available keys

KEY DESCRIPTION

1. Used to remove small variations in the indicator’s zero.

1. Used to weigh an item by using the container.

2. Save tare weight and shows net weight.
1. Used to enter tare weight manually
2. If you press this key, “t 00000” is shown on the display.
3. Enter tare weight with arrow keys and save it by pressing the
ENTER key.
1. Toggles between gross weight and net weight
2. You can prohibit using of keyboard by pressing G/N key for 4 sec
to use keyboard again, press G/N key for 4 sec
1. “*” is used in various way.
2. Used to input the set-point value for batching operation
(Press * key for 2 seconds)
3. You can select this key’s function in SET mode F23.
0. Do not use.
1. PRINT Key.
2. HOLD Key.
1. ENTER key is used in various way.
2. You can select this key’s function in SET mode F24.
0. Do not use
1. TOTAL PRINT key.
2. START key for batching operation
3. STOP key for batching operation
3. Set set-point code for batching operation.(00~49)
(Press the ENTER key for 2 sec.)

47
3) External Control for Input / Output Interface
■ External input

Pin No. SIGNAL LINE NAME DESCRIPTION

24, 25 GND (Input common) External input common
16 ZERO input ZERO key operation
17 TARE input TARE key operation
18 START input Used as START key in batching operation
19 STOP input Used as STOP key in batching operation
“*” is used in various way
20 “*” input
(Set this key in SET mode F23)
“*” is used in various way
21 ENTER input
(Set this key in SET mode F24)
22, 23 Buffer Enable to add the Key function

■ External output (Relay contact)

Pin No. SIGNAL LINE NAME Pin No. SIGNAL LINE NAME
3 Zero band signal output (Out 1) 7 High limit signal output (Out 5)
4 Optional preliminary output (Out 2) 8 Low limit signal output (Out 6)
5 Preliminary output (Out 3) 9 Finish signal output (Out 7)
6 Final weight signal output (Out 4) 10 Stable signal output (Out 8)
11, 12 Output common

■ External control I/O circuit

48
4) How to input the set-point code (00 ~ 49)
There are two ways to input the set-point code

■ First way

Press the ENTER key for 2 seconds to enter set-point (Set-point : 00~49)

DISPLAY DESCRIPTION
Code = 00 Set – point Code Number=00 in weighing control

Code = 49 Set – point Code Number=49 in weighing control

■ Second way
You can enter set-point by using RS-232C, RS-485 Communication
Refer to SET Mode. (In the case of F33 = 4 or F36 = 4, Command Mode )

■ How to clear the Set-Point value (00 ~ 49 )

After input “F88” in the SET Mode, press ENTER key and can see the “Factor” and
“0000” on the display

After input “2007” and ENTER key, can see the “SP init”. In a few seconds,
can see the message of “End” and then exit the SET Mode. It is accomplished

49
5) How to input the set-point value
There are four ways to input the set-point value
■ First way (F50 = 0 )
To enter set-point, press the * key for 2 seconds in weighing mode
Note 1. Set F50 to 0 in set mode
Note 2. Shift the position of cursor with , key and enter set value with , key to
go to next step, press the * key

STEP DISPLAY DESCRIPTION

Point Zero Band
Shift the position of cursor with , key and
STEP1 ZEro bA
Enter Zero band value with , key
1 - 00000 To go to next step, press the * key
oP - Pre Optional Preliminary
STEP2 Input first weight
2 - 00000
PrELiM Preliminary weight
STEP3 Input Preliminary weight
3 - 00000
FinAL Final weight
STEP4 Input final weight
4 - 00000
FALL Free Fall Weight
STEP5 Input free fall weight
5 - 00000
H - LiMit High Limit Weight
STEP6 Input high limit weight
6 - 00000
L - LiMit Low Limit Weight
STEP7 Input low limit weight
7 - 00000

■ Second way (F50 = 0 )

Enter set value from F1 to F17 in set mode.
F11 : Zero Band
F12 : Optional Preliminary Weight
F13 : Preliminary Weight
F14 : Final Weight
F15 : Free Fall Weight
F16 : High Limit Weight
F17 : Low Limit Weight

■ Third way
Enter set-point by using RS-232, RS-485 Communication
Set F33 to 4 in set mode. Refer to set mode. (F33)

50
6) Set-point Condition
Output is done according to the following condition in batching operation.

MODE OUTPUT CONDITION

COMMON Zero band output GROSS weight ≤ Zero band
Optional preliminary
NORMAL NET weight ≥ Final weight – Optional preliminary weight
weight output
Optional preliminary
Loss – in GROSS weight > Optional preliminary weight
weight output
Preliminary
COMMON NET weight ≥ Final weight - Preliminary weight
weight output
Final weight
COMMON NET weight ≥ Final weight - Free fall weight
Output
High limit weight
COMMON NET weight > Final weight + High limit weight
Output
Low limit weight
COMMON NET weight < Final weight - Low limit weight
Output

7) Batching Operation
You can select batching operation method in set mode, F20.

a. USER PROGRAM CONTROL MODE

■ Normal Batching
■ Loss-in-Weight Batching

b. AUTOMATIC PROGRAM CONTROL MODE

■ Normal Batching
■ Loss-in-Weight Batching

51
< Normal Batching Diagram >

< Loss-in-Weight Batching Diagram >

52
USER PROGRAM CONTROL MODE
< Normal Batching >

53
■ You can operate external control for your needs in user program control mode.
■ External input and output signal is as follows.

1. Press TARE key so that the display shows 0kg (NET weight).

2. FIRST OUTPUT(Optional preliminary) :

It is ON when the net weight is greater than the weight
(Final - Optional preliminary).

3. SECOND OUTPUT(Preliminary) :
It is ON when the net weight is greater than the weight (Final - Preliminary).

4. THIRD OUTPUT(Final) :
It is ON when the net weight is greater than the weight (Final - Free fall).

5. HIGH LIMIT OUTPUT :

It is ON when the net weight is greater than the weight (Final + High limit)
after third output is ON.

6. LOW LIMIT OUTPUT :

It is ON when the net weight is greater than the weight (Final - Low limit)
after third output is ON.

7. FINISH SIGNAL :
When weight is stable, It is ON after passing the certain time of start delay
(You can set start delay time in set mode, F21.)
It is OFF after passing the certain time of operating delay or Finish Signal OFF
Range (F22). (You can set operating delay time in set mode, F19.)

8. ZERO BAND OUTPUT :

It is ON when gross weight is lower than zero band value.

9. Discharge gate control signal is not supplied in CI-6000A.

- Use FINISH SIGNAL OUTPUT.

10. Prepare for next batching operation.

54
USER PROGRAM CONTROL MODE
< Loss-in-Weight >

55
■ You can operate external control for your needs in user program control mode.
■ External input and output signal is as follows.

1. FIRST OUTPUT(Optional preliminary) :

It is ON when the gross weight is greater than optional preliminary weight.
It is OFF when the gross weight is lower than final weight.
- Fill in the hopper by using first output signal.

2. Press TARE key so that the display shows 0kg (NET weight).

3. SECOND OUTPUT(Preliminary) :
It is ON when the net weight is greater than the weight (Final - Preliminary).

4. THIRD OUTPUT(Final) :
It is ON when the NET weight is more than the weight (Final - Free fall).

5. HIGH LIMIT OUTPUT :

It is ON when the net weight is greater than the weight (Final + High limit)
after third output is ON.

6. LOW LIMIT OUTPUT :

It is ON when the net weight is greater than the weight (Final - Low limit)
after third output is ON.

7. FINISH SIGNAL :
When weight is stable, It is ON after passing the certain time of start delay
(You can set start delay time in set mode, F21.)
It is OFF after passing the certain time of operating delay or Finish Signal OFF
Range (F22). (You can set operating delay time in set mode, F19.)

8. ZERO BAND OUTPUT :

It is ON when the gross weight is lower than zero band value.

9. Discharge gate control signal is not supplied in CI-6000A.

- Use FINISH SIGNAL OUTPUT.

10. Prepare for next batching operation.

56
AUTOMATIC PROGRAM CONTROL MODE
< Normal Batching >

57
■ Output/input is controlled according as the program of an indicator in utomatic
program control mode.
■ External input and output signal is as follows.

1. Press TARE key so that the display shows 0kg (NET weight).

2. START INPUT: FIRST, SECOND, THIRD output is ON when START key is pressed.

3. FIRST OUTPUT (Optional preliminary) :

It is OFF when the net weight is greater than the weight
(Final - Optional preliminary).

4. SECOND OUTPUT (Preliminary) :

It is OFF when the net weight is greater than the weight (Final - Preliminary).

5. THIRD OUTPUT (Final) :

It is OFF when the net weight is greater than the weight (Final - Free fall).

6. HIGH LIMIT OUTPUT :

It is ON when the net weight is greater than the weight (Final + High limit)
after third output is ON.

7. LOW LIMIT OUTPUT :

It is ON when the net weight is greater than the weight (Final - Low limit)
after third output is ON.

8. FINISH SIGNAL :
When weight is stable, It is ON after passing the certain time of start delay.
(You can set start delay time in set mode, F21.)
It is OFF after passing the certain time of operating delay or Finish Signal OFF
Range (F22). (You can set operating delay time in set mode, F19.)

9. ZERO BAND OUTPUT :

It is ON when gross weight is lower than zero band value.

10. Discharge gate control signal could not be supplied in CI-6000A.

- Use FINISH SIGNAL OUTPUT.

11. Data Output : Data is outputted after finish signal is outputted.

12. Prepare for next batching operation.

58
AUTOMATIC PROGRAM CONTROL MODE
< Loss-in-Weight >

59
■ Output/input is controlled according as the program of an indicator in
automatic program control mode.
■ External input and output signal is as follows.

1. FIRST OUTPUT (Optional preliminary) :

It is ON when the gross weight is greater than optional preliminary weight.
It is OFF when the gross weight is lower than final weight.
- Fill in the hopper by using first output signal.

2. Press TARE key so that the display shows 0kg (NET weight).

3. START INPUT: FIRST, SECOND, THIRD output is ON when START key is pressed.

4. SECOND OUTPUT (Preliminary) :

It is OFF when the net weight is greater than the weight (Final - Preliminary).

5. THIRD OUTPUT(Final) :
It is OFF when the net weight is greater than the weight (Final - Free fall).

6. HIGH LIMIT OUTPUT:

It is ON when the net weight is greater than the weight (Final + High limit)
after third output is ON.

7. LOW LIMIT OUTPUT:

It is ON when the net weight is greater than the weight (Final - Low limit)
After third output is ON.

8. FINISH SIGNAL:
When weight is stable, It is ON after passing the certain time of start delay. (You
can set start delay time in set mode, F21.)
It is OFF after passing the certain time of operating delay or Finish Signal OFF
Range (F22). (You can set operating delay time in set mode, F19.)

9. ZERO BAND OUTPUT: It is ON when gross weight is lower than

zero band value.

10. Discharge gate control signal is not supplied in CI-6000A.

- Use FINISH SIGNAL OUTPUT.

11. Data Output : Data is outputted after finish signal is outputted.

12. Prepare for next batching operation.

60
8) Error Message
Error 01
▣ Reason
The weight is unstable to initialize the scale
☞ Solution
Put the scale on a stable place and turn on the power
Error 02
▣ Reason
Load cell connection failure or error in A/D conversion part.
☞ Solution
Check the load cell connector to see if the polarity of signal is reversed
Error 05
▣ Reason
You pressed any key for long time or problem of key part
☞ Solution
If there is no problem in key part, call your CAS dealer
Error 08
▣ Reason
You have set the operating condition of ZERO key or TARE key not to
operate when the indicator is not stable.
☞ Solution
Reset the operating condition of ZERO and TARE key in SET mode F09
Error 09
▣ Reason
Current weight deviates from zero range
☞ Solution
Set the operational range of the ZERO key within 2% or 10% of the
maximum capacity in SET mode F08
Error 10
▣ Reason
Tare weight exceeds the maximum capacity of the scale
☞ Solution
Tare weight should be lower than the maximum capacity.
Otherwise, the maximum capacity should be greater than the tare
Error 13
▣ Reason
The zero range deviates from the set range
☞ Solution
Confirm that there is nothing on the platter.
If nothing exists, do calibration in CAL mode

61
Error 14
▣ Reason
Gross weight is lower than final Weight in Loss-in-weight batching of
Built-in automatic program mode

OVER
▣ Reason
The weight is exceeds maximum capacity of the indicator
☞ Solution
Do not load the item exceeds the maximum tolerance.
If the load cell is damaged, the load cell should be replaced

62
12. Serial Interface (COM1, COM2)
COM1,COM2 Baud Rate
F30 Device ID 00 ~ 99

COM1 Transmission Mode

F31 Baud Rate 600, 1200, 2400, 4800, 9600, 19200 bps

F32 A Use of COM1 Printer, Sub-display or Computer

F33 Output Mode Stream, Stable, Data is required, Command mode

COM2 Transmission Mode

F34 Baud Rate 600, 1200, 2400, 4800, 9600, 19200 bps
F35 A Use of COM2 Printer, Sub-display or Computer

Stream, Stable, Data is required,

F36 Output Mode
Command mode

COM1,COM2 Data Format

F37 Data Out Format 22bytes and 10bytes of CAS, 18bytes of AND

①. 22 bytes of CAS

- Data bit : 8, Stop bit : 1, Parity bit : None

- Code : ASCII
- When the data is sent to computer?
Select in SET mode
■ Transmit always : 1 is selected in F33, F36.
■ Transmit when weight is stable : 2 is selected in F33, F36.
■ Transmit when data is required : 3 is selected in F33, F36.
Indicator print output format when computer transmits 1 byte of device ID to an indicator.
- Transmission data format (22 BYTE)
. . . DATA (8byte) CR LF
└──┘ └──┘ │ └──────┐ │ └──┘
US(Unstable) GS(GROSS weight) Device ID Lamp condition byte Empty Unit (kg/t)
ST(Stable) NT(NET weight)
OL(Overload)

63
- Device ID : Transmit 1 byte of device ID so that the receiver can receive data
selectively which indicator send.(Device ID is set in F30 .)
- Lamp condition byte : Indicate on/off
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
1 Stable 0 Hold Print Gross Tare Zero

- Data(8 byte) : If 13.5kg, Each ASCII code ‘0’, ‘0’, ‘0’, ‘0’, ‘1’, ‘3’, ‘.’, ‘5’
is transmitted by 8 byte.

- Output error message

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 Byte 8 Byte 9
E R R Error code CR LF

② 10 bytes of CAS

- Data bit : 8, Stop bit : 1, Parity bit : None

- Code : ASCII
- Transmission data format (10 BYTE)
DATA (8 byte) CR LF

③ 18 bytes of AND

- Data bit : 8, Stop bit : 1, Parity bit : Even

- Code : ASCII
- Transmission data format (18 BYTE)
. . DATA (8byte) CR LF
└──┘ └──┘ └──┘
US(Unstable) GS(GROSS weight) Unit (kg/t)
ST(Stable) NT(NET weight)
OL(Overload)

64
 COM1, COM2 RS-232C Connection

(1) COM1 - TXD : 2 pin, RXD : 3 pin, GND : 7 pin

(2) COM2 - TXD : 2 pin, GND : 5 pin

RXD ㅇ ----------------------------- ㅇ 3 Transmit Data

TXD ㅇ ----------------------------- ㅇ 2 Receive Data

GND ㅇ ----------------------------- ㅇ 5 Signal Ground

┌─ ㅇ 1 Carrier Detect

├─ ㅇ 4 Data Terminal Ready

└─ ㅇ 6 Data Set Ready

┌─ ㅇ 7 Request to Send

└─ ㅇ 8 Clear to Send

9 pin port(Male) 9 pin port(Female)

RS-232C port of Cl-6000A Serial port of computer

COM1 PC

RXD ㅇ ------------------------- ㅇ Transmit Data

TXD ㅇ -------------------------- ㅇ Receive Data

GND ㅇ -------------------------- ㅇ Signal Ground

9 pin port(Male) 9 pin port(Male)

RS-232C port of Cl-6000A RS-232C port of PC

COM2 Sub-display, Serial Printer

TXD ㅇ -------------------------- ㅇ Receive Data

GND ㅇ -------------------------- ㅇ Signal Ground

9 pin port(Male) Port of sub-display, serial printer

RS-232C port of Cl-6000A

65
 COM2 RS-422 Connection

COM 2 - OUT (+) : 8pin, OUT(-) : 9pin

IN(+) : 6pin, IN(-) : 7pin

- Transfer Mode : Same to the RS-232C interface

F30 Device ID 00 ~ 99

F34 Baud Rate 600,1200,2400,4800,9600,19200bps

F36 Output Mode Stable, Stable or Unstable, Command mode

Data Format : Same to the RS-232C interface(Only Tx of Indicator)

- How to connect to the RS-485 port

Rx(+):IN(+)⑥ ---┒ DATA +

---┚ ( TRX +)
Tx(+):OUT(+)⑧ ------------
RS –
PC
232C
Rx(-):IN(-) ⑦ ---┒ ------------
DATA -
( TRX -)
Tx(-):OUT(-)⑨ ---┚

9pin port (Male) RS-485 Convertor

RS-485 port of CI-6000A

- How to connect to the RS-422 port

TX+ :Out(+) ⑧ ------- Rx+

TX- :Out(-) ⑨ ------- Rx- RS- ----------------

PC
RX+ : IN(+) ⑥ ------- Tx+ 232C ----------------

RX- : IN(-) ⑦ ------- Tx-

9pin port (Male) RS-422 Convertor

RS-422 port of CI-6000A

66
13. OPTIONS
OP-1 Analog Output Interface (Current Output)

■ Set F56 to 1 in set mode.

■ Specification

Output Current 4 – 20mA, 0 – 20mA, 0 – 24mA

Resolution More than 1/2000

Temperature Coefficient 0.01%

Maximum Load Resistor 500Ω MAX.

■ When the display weight is "0", the output current is 0mA or 4mA.
When the display weight is maximum capacity of the indicator, the output current is
20mA or 24mA.

■ To use current to voltage

If you add a 250Ω shunt resistor, voltage output will be 1 - 5V or 0 – 5V or 0 – 6V.
(250Ω * 4mA ∼ 250Ω * 20mA)

+ 15V

HI

LO

Shunt Resistor

67
■ Switch setting

SW1 SW2 Output

1 1 0 – 24mA
0 1 0 – 20mA
1 0 4 – 20mA

Fixing or Flexibility Setting Set Mode Output

Current
SW4 SW5 SW1 SW2 F57(Min) F58(Max)
4000 20000 4 – 20mA
Fixing 0 0 1 1 0000 20000 0 – 20mA
0000 24000 0 – 24mA

When you use the Fixing Mode (SW4=SW5=0),

you have to set one(1) of the SW1 & SW2 and
you have to set the values what you want to out in the SET MODE (F57 & F58)

Fixing or Flexibility Setting Set Mode Output

Current
SW4 SW5 SW1 SW2 F57(Min) F58(Max)
1 1 0 – 24mA
Flexibility 1 1 0 1 0000 24000 0 – 20mA
1 0 4 – 20mA

When you use the Flexibility Mode (SW4=SW5=1),

you select to set the setting switches what you want to out

If the output current is not correct, you need to adjust the volume resistors of VR1 & VR2.
VR1 is used to adjust to zero value. VR2 is used to adjust to Max. value.

68
 OP-2 Analog Output Interface (0-10V)

■ Set F56 to 1 in set mode.

■ Specification

Output Voltage 0 – 10V

Resolution More than 1/2000

Temperature Coefficient 0.01%

■ The output voltage is 0V when the display weight is "0".

And the output voltage is 10V when the display weight is maximum capacity of the indicator.

SW1 SW2 Output

0 0 0 – 10V

Fixing or Flexibility Setting Set Mode Output

Current
SW4 SW5 SW1 SW2 F57(Min) F58(Max)

Flexibility 0 0 0 0 0000 24000 0 – 10V

You have to set zero(0) of the SW1, SW2, SW4 and SW5

69
 OP-3 BCD Output Interface
Parallel BCD output is the interface that transmits the weight as BCD code.
Inner circuit of input/output circuit is electronically disconnected by photo-coupler
■ Set F55 to 2 in set mode.
■ Transmission mode
F56 Output Logic Positive Logic, Negative Logic

■ Pin Connection
PIN SIGNAL PIN SIGNAL
1 Ground (GND) 26 High : Net, Low : Gross
0
2 1 x 10 27 N.C.
0
3 2 x 10 28 N.C.
0
4 4 x 10 29 N.C.
0
5 8 x 10 30 N.C.
1
6 1 x 10 31 N.C.
1
7 2 x 10 32 N.C.
1
8 4 x 10 33 N.C.
1
9 8 x 10 34 N.C.
2
10 1 x 10 35 N.C.
2
11 2 x 10 36 N.C.
2
12 4 x 10 37 External Vcc
2
13 8 x 10 38 N.C.
3
14 1 x 10 39 External Vcc
3
15 2 x 10 40 N.C.
3
16 4 x 10 41 N.C.
3
17 8 x 10 42 High : +, Low : -
4 1
18 1 x 10 43 Decimal point : 10
4 2
19 2 x 10 44 Decimal point : 10
4 3
20 4 x 10 45 Decimal point : 10
4
21 8 x 10 46 Over Load
5
22 1 x 10 47 N.C.
5
23 2 x 10 48 N.C.
5
24 4 x 10 49 Busy
5
25 8 x 10 50

70
■ 50 pin connector : CHAMP 57-40500(Amphenol) Female
■ TTL Open-Collector Output
■ SIGNAL LOGIC
1. BCD data output : Positive, Negative logic
2. Polarity output : “+” = High
3. OVER output : “OVER" = High
4. BUSY output : “BUSY” = High
■ Standard Accessory :
Mating connector 57-30500(Amphenol) Male 1EA.

■ Weight Data

WEIGHT DATA

BUSY SIGNAL

■ BCD output circuit

+V

Voltage 30V max.

+V +V Current 30mA max.

Output Voltage
0.2V Txp
when ON

CI-6000A1

■ BCD output circuit is Open Collector Type.

71
 MEMO

72
MEMO

73
 MEMO

74
75