MyHOME_Up

BTicino SpA
Viale Borri, 231
21100 Varese - Italy
www.bticino.com

HOME AUTOMATION EVOLUTION

AD-ITMH20GT/GB - Version 01/2020

BTicino SpA reserves at any time the right to modify the contents of this booklet
and to communicate, in any form and modality, the changes brought to the same.

MyHOME_Up Technical guide 2020

Ground floor Kitchen +

Music

Coloured light

Light

Rolling shutter

GUIDE
FOR INSTALLATION
VOICE
COMMAND
CONTROL WITH
SMARTPHONE
MANUAL
CONTROL
TOUCH
CONTROL
AND CATALOGUE
MyHOME_Up

HOME AUTOMATION
EVOLUTION
INTRODUCTION – PROJECT GUIDELINES

LIGHTS AND AUTOMATION

ENERGY MANAGEMENT
- Temperature control
- Load control and consumption display

SYSTEM INTEGRATION

SOFTWARE AND SERVICES – CATALOGUE – APPENDIX

Contents MyHOME_Up
CONTENTS
INTRODUCTION
General features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

PROJECT GUIDELINES
General features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Functional diagram of a MyHOME_Up system. . . . . . . . . . . . . . .22
Preliminary project and system layout. . . . . . . . . . . . . . . . . 24
The installation of a BUS system . . . . . . . . . . . . . . . . . . . . . .24
Light and automation system. . . . . . . . . . . . . . . . . . . . . . . .28
Temperature control system . . . . . . . . . . . . . . . . . . . . . . . . 29
Consumption display and load control system. . . . . . . . . . . . . . .32
Burglar-alarm system. . . . . . . . . . . . . . . . . . . . . . . . . . . .34
NUVO Multiroom audio system . . . . . . . . . . . . . . . . . . . . . . .35
Selection and positioning of the electric panel. . . . . . . . . . . . . . .36
Positioning of the junction boxes . . . . . . . . . . . . . . . . . . . . . .44

Contents MyHOME_Up
LIGHTS AND AUTOMATION
General features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Light and shutter automation system . . . . . . . . . . . . . . . . . . . 46
Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Diagram 1 - Switching on and off of 2 lamps with 4 light points
with general ON/OFF control . . . . . . . . . . . . . . . . . . . . . . . .64
Diagram 2 - Automatic switching on of the light with passive
infrared ceiling sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Diagram 3 - Alternate current motor control for shutters, curtains,
or motorised shutters . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Diagram 4 - Switching on and off of one lamp and shutter control
using an actuator control . . . . . . . . . . . . . . . . . . . . . . . . . .65
Diagram 5 - Switching on, off and adjustment of the light level
of fluorescent lamps through “ballast”. . . . . . . . . . . . . . . . . . .66
Diagram 6 - Switching on, off and adjustment of the light level
of LED lamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Diagram 7 - Lighting system with presence and
lighting sensors - large meeting room. . . . . . . . . . . . . . . . . . .67
Diagram 8 - Lighting system with presence and
lighting sensors - hall and reception. . . . . . . . . . . . . . . . . . . .68

ENERGY MANAGEMENT - TEMPERATURE

CONTROL
General features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Temperature control. . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
General rules for installation. . . . . . . . . . . . . . . . . . . . . . . 76
Sizing of the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
System physical expansion. . . . . . . . . . . . . . . . . . . . . . . . . 76
Association of the devices. . . . . . . . . . . . . . . . . . . . . . . . . .77
Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
4-zone villa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
3-zone villa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

ENERGY MANAGEMENT - LOAD CONTROL AND

CONSUMPTION DISPLAY
General features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Management and load control system . . . . . . . . . . . . . . . . . . .84
Consumption display and energy production. . . . . . . . . . . . . . . .85
Load control and consumption display. . . . . . . . . . . . . . . . . . .86
Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Management and load control system . . . . . . . . . . . . . . . . . . .89
Three-phase load control management and single phase load with
Bus SCS in common. . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
FUNCTION INTEGRATION
General features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Function integration. . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Integration of light automation, load management,
consumption display and temperature control systems. . . . . . . . . .94
Integration of MyHOME_Up systems with BTicino
and/or third party systems . . . . . . . . . . . . . . . . . . . . . . . . . 96

SOFTWARE AND SERVICES

General features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Home configurator Web App . . . . . . . . . . . . . . . . . . . . . . . 103
YouDiagram software . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
MyHOME_SUITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Services and digital tools. . . . . . . . . . . . . . . . . . . . . . . . . 106

CATALOGUES
MyHOME_Up catalogue . . . . . . . . . . . . . . . . . . . . . . . . . . 108
MyHOME_Up FLATWALL catalogue . . . . . . . . . . . . . . . . . . . 130
Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Contents MyHOME_Up
 GENERAL FEATURES

MyHOME_Up: home automation evolution

MyHOME_Up is the integrated modular home automation system based on the BUS
technology with 2 wires pair that offers smart solutions in terms of:
- comfort, thanks to the custom setting of lights, shutters, temperature and music in
every room.
- safety to prevent unwanted intrusions.
- control of consumption and power levels for energy and cost savings and to avoid
overload black-outs.

MyHOME_Up is also an open system, able to

integrate with systems and devices of other
brands to perform advanced functions. Ground floor Kitchen +

Music

Coloured light

Light

Rolling shutter

MyHOME_Up App

HOMETOUCH 7” Touch Screen Control

MyHOME_Up
system

BUS

Digital controls

2
CONTROL MyHOME_UP AS YOU WISH
All the functions may be managed:
- with voice commands using the Google Home
and Amazon Alexa voice assistants.
- using the Smartphone and dedicated app; VOICE COMMAND CONTROL WITH
SMARTPHONE
MANUAL
CONTROL
TOUCH
CONTROL
- with flush-mounted manual controls;
- with HOMETOUCH Touch Screen devices.

NUVO audio system Burglar alarm

LAN network

Systems and devices of other brands

Air conditioning
systems

LAN network Lighting with RGB

lamps
Modem router

MyHOMEServer1
Management of
weather stations
and sensors

Introduction MyHOME_Up 3
WWW.BTICINO.COM
 GENERAL FEATURES

The system functions

LIGHT AND AUTOMATION SYSTEM

System which can manage up to 175 channels (*) In particular it is possible to associate the
(lamps, shutters, controlled sockets etc.). devices found in the system and create
MyHOME_Up application allows start up of the single and general commands and groups
light and automation system and the check of the of lights and shutters.
operation of the individual devices.

Basic contact
interface Shutter control Light control and Full controls

Traditional
device

Power supply

230 Va.c.

TV/SAT IPTV
DIN DIN
module module
actuator dimmer
actuator
automazione diffusione sonora antifurto termoregolazione videocitofonia controllo lan controllo carichi energia luci tvcc www irrigazione

Shutters Lights

Note (*): Channel means the individual relay or output of the actuator for the management of the load.
The count includes any preset or unused outputs.
For example, actuator F411/4 with 4 independent relays is identified in the MyHOME_Up as a 4-channel device.

4
Manageable functions
different lights and loads with ON/OFF and dimmed control;
rolling shutters with UP/DOWN control and management of the preferred position;
automatic switching on of loads as a function of presence (using sensors) or the closing of a
contact (using contact interfaces).

Full controls Voice control HOMETOUCH 7”

Basic
actuator

MyHOMEServer1

Internet
Lights

Introduction MyHOME_Up 5
WWW.BTICINO.COM
 GENERAL FEATURES

The system functions

TEMPERATURE CONTROL SYSTEM

System for the control of a temperature control Manageable functions

system with probes with display, item H/LN4691, temperature display and control using sensor with
used as zone thermostats, and probes item display, Smartphone with APP and HOMETOUCH
3454 for the management of up to 99 zones. touch;
temperature management in the scenarios created
MyHOME_Up application allows start up of the
with MyHOME_UP APP.
system and the check of the operation of the
individual devices. Moreover, if the system is managed using “scenario”
type commands, it will be possible to also manage the
functions using Amazon Alexa and Google Home voice
commands.

Zone 1 Zone 2
Power supply sensor sensor

Actuator for 8 relay

0-10V solenoid actuator
valves

MyHOMEServer1

Internet
Cold
M
0÷10V
Hot

6
 LOAD CONTROL SYSTEM

Using an appropriate control unit, item Manageable functions

F521, and actuators, items F522, F523 management of up to 63 loads with corresponding
and 4672N, the load control system disconnection priority, which can be configured based
manages the maximum power used by the on specific customer needs;
possibility of reactivating the disconnected load using
electric system of the home, automatically
the HOMETOUCH touch screen and flush mounted
disconnecting the less important electrical
devices.
household appliances in case of overload. If the overload condition persists, the control unit
The value of the power that can be will disconnect the next least important household
controlled and set in the control unit is appliance.
between 1.5 and 18 kW.

Central unit for load

management

Electricity meter
HOMETOUCH
Electrical switchboard

BUS SCS

230 Va.c.

Uncontrolled Flush mounted Flush mounted Flush mounted

sockets actuator actuator actuator

230 Va.c.

Uncontrolled Priority 1 Priority 2 Priority 3

load controlled controlled controlled
load load load

Introduction MyHOME_Up 7
WWW.BTICINO.COM
 GENERAL FEATURES

The system functions

CONSUMPTION DISPLAY SYSTEM

System for display by means of energy meters In the MyHOME_Up App the installer must enter the
(max. 128) of consumptions of electricity and addresses of compatible devices, such as the electricity
the production of instantaneous electrical meter, item F520, and the load control unit, item F521
(consumption display only).
energy.

Manageable functions
the instant electrical consumption/production value
can be displayed by the MyHOME_Up APP. Photovoltaic
panel
the App can use the consumption value as a condition
for activating Smart scenarios.

Inverters LAN network

Compact
power supply

Electric Energy
power Data
meter Logger

Energy Display
MyHOMEServer1
Central unit for
load management

Internet

8
 WIRE-RADIO BURGLAR-ALARM system

Burglar alarm system with professional features Manageable functions

and flexible solutions, with the following Control of the areas inside and outside the home.
characteristics: Separate management of the protected areas.
Forwarding of alarm messages with e-mail, SMS and
- Management of max. 128 zones; voice messages.
- Wire solution which can be expanded Creation of Smart scenarios thanks to the functional
integration with other components of the MyHOME_Up
via radio;
system.
- Use of the IP, GSM and PSTN technologies; Moreover, if the system is managed using “scenario”
- Local and remote management using type commands, it will be possible to also manage the
functions using Amazon Alexa and Google Home voice
the BTicino Home Alarm App and the commands.
MyHOME_Up App;
WARNING: for the project and the installation see the
- Wide range of sensors for the internal, specific guide: “New burglar alarm system”.
perimeter and external protection of the
home. Bus/radio
interface

Radio magnetic Curtain radio

contact sensor

KEYPAD

Internet

Expansion
modules
Modem Network cable 4-conductor cable BUS
router

MyHOMEServer1

Central unit

Multipolar cable

Volumetric sensors

Volumetric sensors
Light and
automation system

Siren

Introduction MyHOME_Up 9
WWW.BTICINO.COM
 GENERAL FEATURES

The system functions

NUVO MULTI-ROOM AUDIO SOUND SYSTEM

Multiroom sound system made up of zone

amplifier devices (players) connected to the KITCHEN
speakers and to the home LAN network with
the following features: Speaker

wired solution, suitable for new houses fitted

with wired LAN network;
dual-band wireless (2.4 and 5 Ghz) solution
for existing homes or to extend wired
systems, in rooms of new homes without
wired LAN network.

Player
Manageable functions
player on/off and volume adjustment;
source selection (streaming radio, local network or
Smartphone mp3 files, etc.);
creation of scenarios with activation of players in the
various zones of the home.
Moreover, if the system is managed using “scenario”
type commands, it will be possible to also manage the
functions using Amazon Alexa and Google Home voice
commands.

WARNING: for the project and the installation see the

specific guide “NUVO®: multi-room audio system.

To any other network devices

Internet
Modem router

10
 BATHROOM BEDROOM
Speaker

Speaker

Player Player

LIVING ROOM
Speaker

Player

Introduction MyHOME_Up 11
WWW.BTICINO.COM
 GENERAL FEATURES

Control MyHOME_Up as you wish

MyHOME_Up may be controlled using your voice, flush mounted controls, customised digital controls,
the HOMETOUCH 7” touch screen, or the smartphone App, which also allows remote control of the
home.

VOICE CONTROL USING THE GOOGLE

AND AMAZON VOICE ASSISTANTS

«Ok Google, switch off all the lights»

«Alexa, switch the fan on»
«Alexa, welcome me home»

These are some voice commands for managing

lights, controlled sockets and, through scenarios,
also shutters, the burglar alarm system, the
ideal temperature and the music to stream.

Two solutions for voice control:

- Digital controls with integrated Amazon Alexa

voice assistant , for flush mounted installation
and available in the Living Now range;

- Third-party devices, such as Amazon Alexa

and Google Home voice assistants.
LIGHT CONTROL

VOICE ASSISTANT

"Alexa, what will

the weather be like
tomorrow?"

Google and Amazon

voice assistants

In addition to managing home automation

functions, it will be possible to interact with the
Amazon and Google platforms to request news,
weather information, timetables, etc.

Living Now digital control with integrated Amazon Alexa voice assistant
12
CONTROL WITH MANUAL CONTROLS
Living Now digital controls
Available in the “all key” Living Now range and
with capacitive pushbuttons, these devices
have LED icons that can be selected using the
MyHOME_Up App based on the function to
manage.
Two versions for each need:
- LIGHT control to manage the lighting (1 or 2
lights, groups and general control);
- FULL control to manage from 1 to 3 light,
dimmer, shutter, NUVO audio, load control,
scenario and coloured light functions.

The function associated to the control device

and the corresponding icon can be changed at
any moment by the installer during the start
up of the system and also by the user using the
MyHOME_Up application. LIGHT CONTROL

In addition, the device may also be expanded

for new functions, and moved around the home FULL CONTROL
without any need for rewiring.

Controls with silk-screen printed key covers

The range of manual control devices also includes
products of the Living Now, Livinglight, Axolute and Matix
ranges, to be completed with key covers with silk-printed
function symbols. Also for these controls the association
of the functions is completed using MyHOME_Up.

Introduction MyHOME_Up 13
WWW.BTICINO.COM
 GENERAL FEATURES

Control MyHOME_Up as you wish

CONTROL WITH SMARTPHONE AND

MyHOME_UP DEDICATED APP
Ground floor Kitchen +

This is done using the specific

MyHOME_Up App installed in the Music

Smartphone of the user. The connection Coloured light

to the system takes advantage of the

Light

Rolling shutter

MyHOMEServer1 gateway connected to

the home Wi-Fi network and the Internet
through the modem router. MyHOME_Up APP
No application configuration by the user Gateway item
is required. All the devices to manage MyHOMEServer1

are in fact already recognised when the

system is put into operation, which is BUS
done by the installer using the same App
installed in the own Smartphone.

Wi-Fi Modem router

With MyHOME_Up application it will be possible to:

- control the lights;
- control the shutters;
- adjust the temperature;
Ground floor Kitchen +
- control the controlled socket;
- display the instantaneous consumptions of the
loads (washing machine, cooker etc.);
- control the devices of other brands (LIFEX,
Philips Hue lamps etc...);
- open door locks;
- listen to the music from the Nuvo multiroom Music
sound system;
- create and manage scenarios; Coloured light

- switch the BTicino Burglar Alarm system on/off Light

using the insertion scenarios, activate partitions,
exclude zones and display events and faults. Rolling shutter

MyHOME_Up is available free for iOS devices from App Store

and for Android devices from Play Store.
Tapparella

Luce

Luce colorata
14
Musica
 Temperature control
status notification
CONTROL WITH HOMETOUCH
Automation and audio
TOUCH SCREEN status notification
Thanks to the simple and immediate
interface, with this touch device -
item 3488 (black) and item 3488W
(white) -, users will have all the
functions of the MyHOME_Up
system at their fingertips:
- Lighting;
- Shutter automation;
- Temperature control;
- Nuvo multi-room sound system;
- Scenarios;
- Function possible thanks to the
integration of third-party devices
and systems.
In addition, HOMETOUCH also
integrates the BTicino video door
entry system and can be used as
connected internal unit for the
handling of calls both locally and
from the Smartphone, using the free
DOOR ENTRY App for HOMETOUCH.

HOMETOUCH item 3488

Video door Door Entry APP

entry system

BUS

Wi-Fi Modem
router

MyHOMEServer1

Introduction MyHOME_Up 15
WWW.BTICINO.COM
 GENERAL FEATURES

Discover how easy it is to start the system.

The putting into operation of the system and the definition of the functions with the command-
actuator association is easily completed using the MyHOME_Up App and the MyHOMEServer1
gateway connected to the BUS and the Internet network.
During system operation, the gateway allows users, both inside and outside the home, to manage the
functions and customise their scenarios using their own Smartphone and the MyHOME_Up App.
The putting into operation of the system only requires a few steps:

1 3
Connect all the devices and the Start the App which
MyHOMEServer1 device to the BUS system. will connect to the
The self-learning procedure will be system using Access
completely automatic. After a few minutes Point.
all the actuators will be working perfectly
with default modes.

MyHOMEServer1

2 4
Install MyHOME_Up which can be After logging in select the room of the home and the
downloaded free from Android and iOS function to be defined.
stores, on your smartphone or tablet.

Ground... Kitchen

Add an object

Light Shutter Thermostat

Player Smart TV
3 Controlled
socket

Door lock Audio Energy

MyHome
Cancel

16
 5
Press the pushbuttons of the
devices which perform the function;
if it is difficult for you to reach
the devices you can easily select
them from the list of those which
MyHOME_Up has found on your
system.

PUSHBUTTON

6
Associate all the control devices by pressing their pushbuttons. At the end of the association all
the controls selected will be working perfectly. You will also have created the graphic object to
check the function from the mobile device.

Evening going out

End
Start condition

Identified device
63
MOD: H4652/2
ID: 00B475CE

No start condition
for this scenario
Choose the pushbutton to be associated

1 2 PUSHBUTTON

OK ✔ Your work is finished.

You and your customer can
Cancel
Add a condition
manage the function set.

WARNING: the list of energy Management and Automation devices that can be associated using the MyHOME_Up App is available in the Appendix
pages at the end of the Guide. Any other unlisted devices can be configured using the MyHOME_Suite software discussed in the “Software and
Services” chapter

Introduction MyHOME_Up 17
WWW.BTICINO.COM
 GENERAL FEATURES

An open system

MyHome_Up is an open system that can be

easily integrated, without requiring any system
changes, with the best third-party technologies,
systems and devices in three different ways.

1. NATIVE INTEGRATION WITH MyHOMEServer1:

- simple solution, as the integration drivers are already installed in the device by default;
- the association between MyHOME_Up and third-party devices is completed using the MyHOME_Up App.

Ground floor Kitchen +

Music

Coloured light

Actuators Light

Rolling shutter

MyHOME_Up
APP
MyHOME_Up
system
BUS LAN network

MyHOMEServer1

NUVO audio system

Lighting with
RGB lamps

DMX

18
2. INTEGRATION WITH DRIVER MANAGER ITEM F459:
- Specific device for the use of integration drivers purposely created based on the characteristics and functions of
the system to integrate (for example to integrate MyHOME_Up with HVAC Samsung and Mitsubishi systems, etc.);
- scalable and customisable solution for the realisation of functions not available with the MyHOME_Up system;
Reliable operation thanks to local interoperability.

SPECIFIC DRIVER

OTHER BRAND SYSTEMS:

Air conditioning
LAN systems
BUS network

Sensors,
MyHOME_Up Driver manager F459 measurement
devices etc.

3. INTEGRATION THROUGH THE USE OF APPLICATION

PROGRAMMING INTERFACES (API). WORKS WITH

API integration can be made in two ways:

- interoperability through IP platform
sharing of different languages (locally
and through the cloud).
- interoperability through IOT Cloud
platforms, such as Artik Samsung and
similar.
These solutions are available and
developed by the “Works with Legrand”
integration platform.
For the details visit bticino.com site

For more information please visit the https://bticino.com site

Introduction MyHOME_Up 19
WWW.BTICINO.COM
 GENERAL FEATURES

An open system - the scenarios

The integration among the MyHOME_Up APPLICATION Tavern
different functions of MyHOME_ The creation and management of
Up and any third-party systems scenarios (up to 50 per system) can be
allows to create and manage easily completed by users, using their
the Scenario function for the Smartphones and the MyHOME_Up
simultaneous activation of App.
several devices. Kitchen
For example, the switching on
of certain lights at a specific
intensity level, the raising of the
shutters to a certain height, the
switching on of specific music to
ensure the comfort of the user in Living room
a specific situation.

Favourites Home Scenarios Other

MyHOME_Up App

Scenario activation
pushbutton

Type of scenarios that can be made

Scenarios Scenarios
with MyHOME_Up:
It is possible to set two types of scenarios:
- with manual activation.
- with automatic activation at certain times
or days, based on states and conditions
occurring in the system, such as:
Day Day
Touch a pushbutton

An object changes status (e.g. a

rolling shutter goes up) Scenario performance

Do you want to start Day?

A Burglar Alarm system partition
changes status when an insertion Start
scenario is switched on
Cancel
The weather conditions set occur Favourites Home Scenarios Other Favourites Home Scenarios Other

Scenario selection Activation

I am leaving or approaching the
house

It is 8 am from Monday to Friday

20
CONTENTS
MyHOME_Up – Project guidelines
General features. . . . . . . . . . . . . . . . . . 22
Preliminary project and
system layout. . . . . . . . . . . . . . . . . . . . 24

Project guidelines MyHOME_Up 21

WWW.BTICINO.COM
 GENERAL FEATURES

Functional diagram of a MyHOME_Up system

The procedure for the creation of a MyHOME_Up system It will be necessary to install a wired and Wi-Fi network
is similar to that for a traditional system. connected to the Internet, for the integration of
Power supplies and other DIN modular devices must be MyHOME_Up with the burglar-alarm system, with the
installed in a general panel. All the others must be flush NUVO audio system, and with any installed third-party
or wall mounted. devices.
However, differently from traditional wiring, in this case Internet connection is also required for the remote
the wiring will be using a grey 2 wires BUS cable for control of the system using a Smartphone.
MyHOME_Up devices, and a white one for video door
entry devices.

Ground floor Kitchen +

MyHOME_Up
APP
Music

Coloured light

Light

Rolling shutter

ADSL line
(Intenet)

Wi-Fi Router BURGLAR ALARM

automazione diffusione sonora antifurto termoregolazio

ELECTRIC PANEL
Video door entry system BUS

LIGHT/SHUTTER AUTOMATION

MyHOMEServer1

MyHOME_Up BUS

GREY BUS pair

NETWORK cable
WHITE BUS pair

22
 The MyHOMEServer1 device is at the heart of all the As it can easily be seen in the diagram, some
integrated system. When putting the system into operation, MyHOME_Up system components are integrated with
it is used to recognise and associate to each other all the each other by sharing the BUS cable, while others,
installed devices. It also acts as a gateway, allowing the such as the Burglar Alarm system and the NUVO
user to control the functions of the system and of third- audio system, third-party products (for example
party products using the HOMETOUCH touch screen, coloured lamps) and voice assistants, are integrated
Amazon Alexa or Google Home voice commands, or with the system through the wired or wireless
remotely using the Smartphone and the MyHOME_Up App. domestic LAN network connection.

Devices of other brands

LAN network

NUVO Player

optional connection
VIDEO DOOR ENTRY SYSTEM

HOME TOUCH

TEMPERATURE CONTROL ENERGY MANAGEMENT

Project guidelines MyHOME_Up 23

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

The installation of a BUS system

FEATURES OF THE MyHOME_UP WIRING

The MyHOME_Up home-automation system uses BUS As can be seen from the diagram given below, relating
installation technology: all the devices are connected to the lighting system, the power line for the load power
“in parallel” by means of a two-conductor wire, used supply is free of the control line and the control line is
to transport the information and low-voltage electrical independent of the functional wiring.
power supply (27 V d.c.).

L
T
N Actuators in switchboard

BUS

Control device Control device Actuator

Junction box Junction box

BUS

24
MAKING THE WIRING

The wiring distribution can be made with:

- Free structure
- Star structure
The selection must be made in relation to the
installation needs, the functions required, wall
limitations, refurbishments or new buildings.

Wiring with free structure

This wiring is usually used in traditional distributions.
If the building already has energy system conductors
with suitable diameter they can be used to insert
the BUS pair because it has an isolation voltage of
300/500 V.
These indications also apply to the installation of the
junction boxes which must be arranged in suitable
number and positions to the “in parallel” connection
of the various stretches of pair.

Wiring with star structure

This wiring should be used when the system will be
integrated with the data transmission, video door
entry, CCTV, sound, telephony and TV/SAT systems in
a single conductor.
The wiring structure is made up of a central point
called the “star centre” made with a switchboard
or an electrical board in which all the peripheral
branches of the various wirings converge.
The conductors must be installed providing junction
boxes every 10 metres for the pulling of the wires.

Device Junction box Power supply

Project guidelines MyHOME_Up 25

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

The installation of a BUS system

CHOICE OF THE WIRING CABLES

BTicino cable 336904 and 336905 BTicino cable l4669

Cable consisting of 2 twisted This cable is used for BUS systems
conductors with 0.50 mm2 section in the following applications:
for each conductor. It can be used Automation, Energy control and
for video door entry systems, and Temperature control. Thanks to the
also for MyHOME_Up systems when BUS cable with 300/500 V insulation
White cable underground installation is required, and the cover for the protection of
336904
running inside appropriate conduits, the clamps with which all devices are
as it complies with the requirements equipped, BTicino systems can also
of the IEC 20-11 standard. be installed in the same boxes and
The cable item 336905 is a low conduits as the power line (230 Vac).
toxicity cable, halogen-free, to be
Technical features
used where fire safety is particularly
critical. - SCS sheathed pair made up of 2
Grey cable flexible conductors with unshielded
L4669 L4669/500 Technical features twisted sheath
- SCS sheathed pair made up of 2 - Insulation voltage: 300/500 V
flexible conductors with unshielded - In compliance with the CEI 46-5
twisted sheath and CEI 20-20 standards
- Insulation voltage: 400 V - Coil length:
- In compliance with the EN60811, - 100 metres (item L4669)
EN50289, EN60228, 50265-2-1, - 500 metres (item L4669/500)
EN50395, EN50396 standards
- Coil length: 200 metres

Cable coexistence The video door entry system and

Although the construction of sound system WHITE BUS can be
the cables guarantees 300/500 routed inside the same conduits of
V electrical insulation, there is the data transmission, telephone
no guarantee of immunity from and TV-SAT cables. However, it must
Cable L4669
disturbance, which may occur when be kept separate from the power
the cable is installed inside the same line.
conduits as the 230 V power supply The separation of the power lines
cables. These types of installation from the signal lines MUST also be
are strongly NOT recommended. ensured inside the junction boxes
and the electric panel.
However, in case of refurbishment, Therefore, attention must be paid
the grey cable, items L4669 and to the point of entry of the conduits
L4669/500, and the white cable, in junction boxes and the electric
item 336904/..5, can be routed panel.
inside the same conduits of the
Cable 336904 traditional electric system. This
solution ensures significant savings,
both in terms of masonry works and
financial.

26
The following table can help to select the type of cable to use based on the MyHome application.

MYHOME APPLICATIONS
COMFORT SAVING COMMUNICATION CONTROL

Lighting Automation Temperature Energy Video door Data Video Web

control Management entry system network Server

BTicino
336904
and 336905 (*) (*) (*) (*)
L4669HT
(white)

BTicino
L4669 and
L4669/500
(grey)

BTicino
L4668CM
UTP 5

Multi-pair
UTP 5E
BTicino
C9881U/5E
C9882U/5E

Cables recommended by BTicino (meeting the installation regulations)

Cables that may be used (for every system check against the installation regulations)

NOTE (*): Mandatory for the underground sections of the individual systems

Project guidelines MyHOME_Up 27

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

Light and automation system

POSITIONING OF DEVICES (POWER SUPPLIES AND ACTUATORS) DEPENDING ON LOCATION

Comply with the following Centralised installation: the actuators are

grouped together in the electric panel
recommendations:
- 1, 2 or 3 rooms: group the
DIN actuators together in the L
T
electric/home automation panel, N
and distribute flush mounted Actuators in switchboard

actuators.
- more than 3 rooms: group
together and, when convenient,
distribute the actuators inside
junction boxes. A “flush mounted”
actuator should be preferred for BUS
the shutters.
- several floors: install an electric
panel for each floor, for grouping
Control device Control device
the actuators together. Where it is
convenient to install the actuators
in junction boxes.

Junction box
BUS

Power supplies

L
T
N

Actuator
Temperature Control
Probe
Control device Control
device

Junction box Junction box

BUS

Distributed installation: actuators and control devices are installed in device or junction boxes.

28
Temperature control system

The design of a temperature control system must be completed with the help of the temperature control
system/water system designer, in order to allow for the following requirements:

SEPARATION OF THE SYSTEM Bathroom

INTO ZONES
Kitchen
To allow zone temperature control of Bedroom
the home, the solenoid valves for the
management of each individual zone
must be installed on the distribution
manifold.

Solenoid valves Manifold

Input
Living room
Bedroom
Kitchen Manifold

Bathroom Living room

Example of system split into zones

with radiant panel heating
Box

TYPES OF MANAGEABLE The MyHOME temperature

SOLENOID VALVES control system can also
manage circulation pumps
The solenoid valves for the
(see figure 4).
management of the zones must be
of three types:

- with ON/OFF contacts

WARNING:
proportional mixing valves

M
- with open/close contacts

M
cannot be directly managed
by the MyHOME temperature
- with open/close contacts control system. They require
0÷10 Volt an external control unit
supplied by the radiant panel
system manufacturer.
M
0 to 10
Project guidelines MyHOME_Up 29
WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

Temperature control system

TYPES OF SYSTEMS THAT CAN BE MANAGED

a. Radiators b. Fan-coil c. Radiant panels d. Systems:

Heating Cooling Both

Kitchen
NOTE: Bathroom Bedroom

In central systems with each home

fitted with a distribution manifold, it will
be possible:

- To install at the manifold input a

Etrance
meter for the measurement of the hall
quantity of heat used;
Living room
- To install solenoid valves for managing
the different zones of the home.

Bathroom
Kitchen
Bedroom

Distribution
manifold
Etrance
hall

Zone solenoid
valves Living room

Counter

Central Example of central system split into

boiler several zones for several apartments.

30
DISPOSITION OF SOLENOID VALVES AND ACTUATORS

The typical setup requires all the

solenoid valves to be installed on Solenoid valve Junction box
the manifold, grouped in a box in actuators 1 2 3 4
1 2 3

C1 C2
4

ART.F430/2
1 2 3 4
1 2 3

C1 C2
4

ART.F430/2
1 2 3 4
1 2 3

C1 C2
4

ART.F430/2
1 2 3 4
1 2 3

C1 C2
4

ART.F430/2

the boiler room. In this case, it

is recommended to group all the
actuators in a switchboard and
install this near the box itself. In Hydraulic
manifold
homes with several floors this
solution can be replicated for each
Zone solenoid
floor. valves

Box

Fan-coil systems Installation of the solenoid valve Installation of the solenoid valve
in 2-tube fan-coils in 4-tube fan-coils
In fan-coil systems the solenoid
valve may be installed inside the fan-
coil itself. In 2-tube systems there
is one single solenoid valve for both
the heating and cooling function. In
4-tube systems there are 2 solenoid M M
valves, one for heating and one for
cooling.

Radiant panel systems Three-way

Actuators
mixing Zone Protection
In radiant panel systems, after valve solenoid valve circuit breaker
the pump it will be necessary to
install a three-way mixing valve
capable of mixing the water so that
it does not exceed the maximum
set temperature limit. The mixing
valve is managed by the control unit
supplied by the radiant panel system M
manufacturer.
To the zone 230 Va.c.
radiant panels
Power supply
To the
other
Circulation Mixing valve devices
pump control unit

Project guidelines MyHOME_Up 31

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

Consumption display and load control system

TYPE OF WIRING
The selection of the way the load is managed (forced reactivation in case
of disconnection) and the mode for the display of the energy consumption
levels define the characteristics of the electric wiring.

LOAD MANAGEMENT: Switchboard

- flush mounted actuators combined with power sockets will
require distributed BUS wiring, in order to reach the devices in
the different device holder boxes.

Power cables
BUS cable

- in case of DIN actuators grouped in the switchboard, allow for the

wiring of the BUS where central control and display devices will be
Switchboard with
installed (load control panel, local display, touch screen, etc.). DIN actuators
From each switchboard actuator a dedicated line (phase and
neutral conductor) will reach the corresponding controlled load
socket.

Power cables

BUS cable
Load control panel

32
CONSUMED AND PRODUCED ENERGY DISPLAY
Group the DIN module meters in the switchboard. Install energy meters, with their toroids, for each electric
line for which the display of consumption is required.

Switchboard

Photovoltaic
panel

BUS

Inverters

LAN network

Electric
power Energy Data
meter Logger

Project guidelines MyHOME_Up 33

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

Burglar-alarm system

TYPE OF WIRING
The installation of a burglar-alarm system is completed with 3 different types of wiring.

a) BUS wiring with 4-conductor cable for the parallel b) “star” wiring with 4-conductor cable for connection
connection of the following devices: to the control unit of all the sensors (volumetric
- keypad; sensors, magnetic contacts, etc.).
- expansion modules; b) Control units with Ethernet port must be connected
- telephone communicators; to the Internet through the home LAN network using
- sirens. appropriate wiring.
For further details see the “New Burglar-Alarm System ”
technical guide.

Volumetric
sensor
Volumetric Magnetic contact
sensor

Star wiring

Volumetric
Volumetric sensor sensor

Possible LAN network

To other BUS devices BUS wiring

Keypad

Telephone Indoor siren

communicator

+ A B -
System central
unit External siren

Cable shield-
ing

NOTE: connect the shielding only to

the “–” clamp of the central unit

34

+ A B -
NUVO multiroom audio system

TYPE OF WIRING
IT is possible to create three different types of system: - WIRELESS SOLUTION: in this case all the players with
- WIRED SOLUTION: all the players are connected to the their speakers can be distributed freely in the various
LAN network using a network cable belonging to cat. rooms.
5E or higher. - MIXED SOLUTION (wired LAN with radio expansion): if
The devices can be installed: sound systems are to be set up in rooms which do not
- in an appropriate rack; have wired LAN network a mixed wired-radio system
- in every room (stand-alone installation). can be created.
In the first case the wiring of all the speakers is from For further details see the “NUVO Multi-Room Audio
the rack. System” technical guide.

When designing the NUVO multi-room audio system, it must be considered that this requires connection to a LAN
network with Wi-Fi modem/router, in order to take advantage of shared streaming music services and for any
firmware updates for the management of products and Apps.

WIRE SYSTEM WITH RADIO EXPANSION

LIVING ROOM BEDROOM BEDROOM KITCHEN

Tabletop

1-zone player
KITCHEN

LIVING ROOM

Soundbar

Rack
LAN

To other players for

2ND CHILDREN BEDROOM
L = 90 m max.

a maximum total of 5

STUDIO

Modem/
Router
Wi-Fi
1-zone player
Tabletop
LAN LAN

to other zone
players or LAN
network devices

Project guidelines MyHOME_Up 35

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

Selection and positioning of the electric panel

The integration of different Proceed as follows:

MyHOME_Up systems inside the
- For installation in new or
building brings the need to group in
existing buildings (restorations),
one single central point all the active
on one or several floors, for
(power supply units, interfaces,
which the creation of a technical
telephone switchboards, etc.) or
room for the electric panel of
passive devices that contribute to
the home is planned, it will
the control and the management of
be possible to choose either
all functions.
wall or flush mounted control
panels or switchboards of the
Multiboard and Idroboard series
for the integration of MyHOME_Up
system. MyHOME
FLATWALL 240 - 270
- For installation in new single
floor buildings and apartments
without any available technical
cabinet or room for the Integration
of the MyHOME_Up system,
BTicino makes available MyHOME
FLATWALL, an innovative solution
for the centralised installation of
electric and electronic equipment
and user interfaces that fully
meets the aesthetic requirements
of the home.

MyHOME
FLATWALL 150

Overview of switchboards for surface and

flush mounted installation

36
ELECTRIC PANEL POSITION
The position of the electric panel must be defined based on the type of building. It is recommended to agree
with the installer the most appropriate position of the electric panel (if not already decided).

One-floor building More than 3 rooms and kitchen and

1, 2 or 3 rooms + bathroom and kitchen: install one bathroom
single electric panel in a central position, for grouping install one single panel in a central position. DIN
all the DIN devices. devices will partly be centralised in the panel and
partly distributed.

Electric DIN modular

Flush panel 1
1
2
2
3 4
3 4

038 42 device
Electric mounted C1 C2

panel devices

1 2 3 4
1 2 3 4

038 42

C1 C2
Flush
mounted
devices

Electric
Multi-floor building panel 1
1
2
2
3 4
3 4

Install a main panel in a technical room or under the

038 42

C1 C2

stairs, and a panel for each floor in a central position. 3rd FLOOR
DIN devices will partly be centralised and partly
distributed.

2nd FLOOR

1st FLOOR

Technical
room

1 2 3 4
1 2 3 4

038 42

C1 C2

Flush
mounted
devices

Project guidelines MyHOME_Up 37

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

Selection and positioning of the electric panel

MyHOME FLATWALL: AESTHETIC AND FUNCTIONAL VALUE WITH MINIMUM
SPACE REQUIREMENTS
MyHome Flatwall features an elegant design and extreme functionality MyHOME
of all its components. FLATWALL 240 - 270

The accessibility to the installed

devices depends on the use:
- Some parts are only accessible to
the installer, for the maintenance
of the installed components; MyHOME FLATWALL 240–270
- Some are also accessible to the Available in the switchboard,
end user for interaction with the electric panel and floor riser
system. versions, it allows the management
Thanks to a protrusion from the wall of the distribution of all the electric
of only 2 cm, finishing panels that services in modern homes.
can be painted, and the anodised Installation can be made both in
aluminium lateral frame, MyHOME masonry walls (load-bearing and
FLATWALL can guarantee maximum partition walls) and in plasterboard
integration with its surroundings. walls.

MyHOME
FLATWALL 150

MyHOME FLATWALL 150

MyHOME FLATWALL 150 is the ideal choice
for housing all the necessary devices for a
basic home automation system (up to 180 DIN
modules) with minimum space requirements.
The latest version has aesthetic and functional
characteristics in line with those of the
well-known Flatwall 240-270. Most of the
complements and accessories are compatible
with both versions, with the exception of the
bottom cable entry points that do not require a
tube fastening plate, therefore avoiding to reduce
the useful space for the housing of the devices.
Installation possible in both masonry and
plasterboard walls.

38
The Flatwall offer includes a box intended for
the installation of multimedia devices (router,
modem, etc.) part of the Home network,
which is approved by all the main telephone
operators.

Box intended for the installation of multimedia devices,

such as ADSL modems or routers. The installation
requires the use of a support for 36 DIN modules (3787).

Switchboard for protection and safety devices, accessible

to the end user. Available in three versions (glass,
metal and plastic), featuring the possibility of reversible
installation. The hinged side can in fact be indifferently
positioned on the right or the left, so that the door can be
opened from the most comfortable and functional side.

Area accessible to the installer with all the power supplies,

actuators and other DIN devices (up to 288 modules) for
the operation of the MyHOME system. The installation is
completed with the white finishing panels.

Project guidelines MyHOME_Up 39

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

Selection and positioning of the electric panel

MyHOME FLATWALL: INSTALLATION SOLUTIONS

SWITCHBOARD ELECTRIC PANEL

1 Configuration for the installation of a 3.5”
2 Configuration for the installation of the
touch screen, and electric safety earth leakage DIN power supplies and the actuators
and thermal magnetic circuit breakers. of the MyHOME_Up system.

EXAMPLE OF FLATWALL H 150 INSTALLATION:

small homes or home automation systems with basic functions.

MyHOME FLATWALL 150

Switchboard solution

2
1
Electric panel type solution

40
 MyHOME FLATWALL 240 - 270
Switchboard solution

FLOOR RISER
3 Configuration going through the various floors of the
building, for wired distribution of common services
(only possible with Flatwall 240-270).

All these solutions can be fully integrated with their

surroundings thanks to the finishing panels, which are
available in white and can be painted using the most
common wall paints.

EXAMPLE OF FLATWALL 240 - 270 INSTALLATION

Electric panel type

solution
1 Floor riser solution

2
3

Project guidelines MyHOME_Up 41

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

Selection and positioning of the electric panel

MyHOME FLATWALL: INSTALLATION

The compact sizes of the flush If installed during the construction then installed on the metal base
mounting bases, only 8.5 cm of the wall, the metal base also already in the wall.
thick, make it possible to install allows construction material To preserve their integrity, the
MyHOME FLATWALL using the savings. finishing elements can be installed
same procedure as for pocket The required device holders can be after completing the masonry
sliding doors. equipped before being installed, and works.

Partition walls Plasterboard walls Load-Bearing Walls

NOTS: for installation in bearing walls, make a 60 cm wide recess from floor to ceiling. For partition or plasterboard walls, leave an
opening of approximately 60 cm during the construction of the wall.

42
Example of typical masonry wall
installation.

Area intended for exposed

devices that must be accessed for
Side entry for corrugated pipes.
interaction purposes

Box intended for the installation of multimedia devices (router,

mode,, etc.). The metal tray, which can only be installed on
36-module device holders, has cut-outs on all the sides for a flexible
management of the cable-through areas. 4 rubber cable glands
are also supplied as standard, required in order to guarantee the
protection of data and power cables. A separate kit with 8 cable
glands is also available (3831) in case of installation of multimedia
devices requiring a high number of cables. The devices are secured
in place using appropriate clips (F496/MF). *

Wall fixing brackets.

Area intended for

protection devices
(stop&go, thermal Area intended for
magnetic circuit MyHOME devices
breakers, etc.)

Tube fastening plate

In order to facilitate cable entry, MyHOME FLATWALL (240 - 270 H
* The metal structure of Flatwall limits the Wi-Fi signal. Therefore, version) has been designed to accept several corrugated tubes, both
during the design it will be necessary to allow for the need for an at the sides, through cut-out holes, and the bottom, where they can
external aerial. be secured in place with a tube fastening plate. This operation is not
required for the Flatwall h 150.

Project guidelines MyHOME_Up 43

WWW.BTICINO.COM
 PRELIMINARY PROJECT AND SYSTEM LAYOUT

Positioning of the junction boxes

SELECTION AND INSTALLATION CRITERIA

The position and the quantity of junction boxes must be assessed based on the type of building.

Apartment on 1 floor Apartment on several floors As an alternative, where appropriate

- 1, 2 o 3 rooms + bathroom and Allow for a junction box underneath install MyHOME FLATWALL in order
kitchen: junction boxes are in each electrical panel, and other to group all the DIN devices together
minimum number and intended junction boxes around the home for in a central position.
for cable joints. All DIN devices are housing the DIN devices of the home
grouped in a central position. automation system.
- More than 3 rooms + bathroom DIN devices are partly centralised
and kitchen: junction boxes are and partly distributed.
also used for housing the DIN
devices of the home automation
system. DIN devices are partly
centralised and partly distributed.

Main junction box

30 cm

NOTE: For the installation of the boxes refer to the IEC 64-50 standard.
The guide recommends a height from the floor exceeding 17.5 cm.
We recommend approximately 30 cm.

44
CONTENTS
MyHOME_Up – Lights and automation

General features. . . . . . . . . . . . . . . . . . 46
Wiring diagrams . . . . . . . . . . . . . . . . . . 64

Lights and automation MyHOME_Up 45

WWW.BTICINO.COM
 GENERAL FEATURES

Light and shutter automation system

The system allows to use physical commands, touchscreen devices, smartphones and voice commands to
manage the following functions:

LIGHTING AUTOMATION OF SHUTTERS, LIGHT AND AUTOMATION

Management of traditional CURTAINS AND OTHER SCENARIOS
incandescence lamps, and LED, DEVICES Execution of a range of simultaneous
fluorescent and halogen lamps, Movement of shutters, curtains, operations called “scenarios”.
with ON/OFF and DIMMER mode. doors and other motor-driven Using a physical device, voice
devices, with monostable and commands, or automatically for
bistable UP/DOWN (or OPEN/CLOSE) calendar-based set events, etc., it
mode and recall of a stored position is possible to activate at the same
(Preset function). time some room lights and the
opening of some shutters. If the
system is integrated with the NUVO
and temperature control systems,
background music and desired
temperature can also be set.

Basic contact
interface Digital controls Voice control

Traditional
device

Power supply

230 Va.c.

DIN TV/SAT DIN IPTV Full control TV/SA

module module and shutter

actuator dimmer actuator
actuator

automazione diffusione sonora antifurto termoregolazione videocitofonia controllo lan controllo carichi energia luci automazione tvcc diffusione sonora www antifurtoirrigazionetermoregolazione videocitofonia controllo

Shutters Lights Shutters

46
SYSTEM COMPOSITION Both devices are available in the
In the system there are two types of advanced digital version, with Living
device: Now finish, or in the version with silk-
screen printed key covers, and with
- Controls, connected only to the BUS
Living Now, Axolute, Livinglight and
wire;
Matix finish.
- Actuators, connected to the BUS
The range of control devices is
cable and to the 230 Vac power line
completed with other capacitive
to manage the load.
sensor and IR infrared products.

Digital controls HOMETOUCH

MyHOME_Up APP

Ground floor Kitchen +

Music

Coloured light

Light

Rolling shutter

Basic
actuator TV/SAT IPTV

automazione diffusione sonora antifurto termoregolazione videocitofonia controllo lan controllo carichi energia luci tvcc www irrigazione

MyHOMEServer1
Full control and
shutter actuator

Lights Shutters

Lights and automation MyHOME_Up 47

WWW.BTICINO.COM
 GENERAL FEATURES

Light and shutter automation system

LIVING NOW DIGITAL CONTROL DEVICES

These devices are made using construction solutions The function to manage can be recognised thanks to a
that simplify assembly and allow the addition or number of LEDs that make up the function symbol.
modification of the home automation functions, which The installer decides which functions to associate to the
can be managed with maximum flexibility. commands using the MyHOME_Up App. The same App
Compared with other civil series controls, the digital can then be used by the user to customise symbols and
control is no longer a 2 module flush mounted element functions to personal taste.
to use with the corresponding key cover, but rather a
digital element of reduced size that can be installed
without front cover plate.

Support K470..

Blanking
module K4950

Function indication
LED matrix
Electrical
contact


Connection
modules

2
Electrified frame

Installation of control devices with DIN

3
Switchboard actuators.
In addition to the connection module, install 2
Digital controls and/or
false poles, item K4950, in any position.
blanking modules

48
They are available in two versions:

- FULL controls: advanced devices that can be set using the MyHOME_UP App, with a LED matrix
for the definition of a wide range of functions, such as ON/OFF and Dimmer lighting, shutter
management, scenarios, NUVO player, coloured light, load management etc.
IT is possible to simultaneously manage up to 3 different functions.

Overview of some icons of

the functions managed by
the advanced controls.

Shutter Dimmers Group Night and day Coloured

UP/DOWN control scenario light

- LIGHT controls: with 3 LED indicators, top, centre and

bottom, for the management of 1 or 2 lights.
It is possible to also configure controls for the
management of 1 or 2 groups of lamps, or for general
commands.
Management Management
of one light of two lights

With reference to the illustration of the previous page, This solutions simplifies wiring of two or more control
digital devices are installed in their respective flush devices as it is no longer necessary to have a “parallel”
mounted box and support, item K470..., using an connection of the BUS cable. At the same time, it also
appropriate “frame” with 27 Vd.c. control device power facilitates the replacement and repositioning of the
supply contacts. control device, also by the user, without the need for
The BUS cable is connected to the electrified frame wiring.
using the connection module, item K8001.

Removal of the control devices from the electrified frame for installation in a different position.

Lights and automation MyHOME_Up 49

WWW.BTICINO.COM
 GENERAL FEATURES

Light and shutter automation system

COMPOSITION OF DIGITAL CONTROLS
For each type of box, the electrified frames used and the number of devices and the accessories that can
be installed are indicated.

2 modules 3 modules 4 modules

Flush mounted
boxes 502E 503E 504E
(70x70x50 mm) (108x74x53.5 mm) (133x74x53.5 mm)

Plasterboard boxes
PB503N PB504N
PB502N (132.5x71x52 mm)
(ø 71x50.5 mm) (110x71x52 mm)

Supports
K8102 K4703 with screws K4704 with screws

Flush mounted
devices
- connection module * *
K8001;
- actuators K8002L
and K8002S;
3 modules 4 modules
- additional power
supply K8003
(2 modules).

Blanking module
K4950
max. 2 blanking modules max. 3 blanking modules

Electrified frame
3 modules 3 modules 3+1 modules 4 modules 4+1 modules
..8102P1 ..8103 ..8103P1 ..8104 ..8104P1

Voice control item

..8013 (3 modules)
Digital control
Light item ..8010
and Full item ..8011
Cover for blanking
module item 4950
WARNING FOR THE SELECTION OF THE DEVICES:
1. Note (*) The connection module is necessary; its position is free inside the box.
2. If the installation of the additional power supply, item K8003, is required for the voice command, item ....8013 (see the MyHOME_Up guide for the details),
connection module item K8001 must not be installed. The additional power supply (space required 2 modules) can only be installed in the electrified frame or
together with 1 or 2 actuators, depending on the size of the box.

50
 ALLOCATION OF THE FUNCTIONS TO
MANAGE
Pian... AND CONFIGURATION OF
Cucina ICONS Cucina
Pian... Pian... MyHOME_Up
Cucina App Pian...

Like all the MyHOME_UP devices, also with digital control

devices the definition of the functions to manage and
the association with the respective actuator require the Dispositivo identificato
MyHome_Up
Annulla Configurazioneapplication and the MyHOMEServer1
Annulla web
Configurazione Annulla Configurazione Annulla C
MOD: KW8002L Dispos
server. ID:00D16020 Lu

Using the same App, it will be possible to select the symbol Pian
Identificazione
of the function managed.
Attuatore/Uscita Scegli il canale da associare
Attuatori/uscite compatibili con Luce Cucina 1 di Piano terra - F411/4 - ID:00
Per identificare l'attuatore/uscita da Luce Cucina 1 Cucina Nessuna etich
associare al'oggetto grafico Luce Cucina Ricerca per ID o modello
1, premi uno qualunque dei pulsanti a
bordo del dispositivo F411/4 - ID:00D16020
Test H4652/2 - ID:
Nessuna etichetta
1 2 Pulsante 1
KW8002L- ID:00D1604B Nessuna etich
Test
Nessuna etichetta

A te la scelta
Non posso premere il ... Aggiungi un pulsante
Aggiungi dispositivo Controlla un altro
OK oggetto Pre
Aggiun
Il tuo comando accende una sola luce ma da Il tuo comando controlla una luce ma vorresti
Con Living Link decidi tu cosa è meglio per te.
quel comando ne vorresti accendere anche gestire un gruppo di tapparelle? Per ini
Vediamo qualche esempio di cosa pui fare
Chiudi un'altra? Chiudi Cambia Annulla
funzione

Shutter Dimmers Coloured

UP/DOWN light
Salta Continua Continua Continua

Comando base Comando evoluto Comando evoluto C

2 tasti 1 tasti 2 tasti 3
Carrier 11:42
Pian... Cucina Pian... Cucina Pian... Cucina
Back Configurazione Fine Cancel Configuration Annulla Configurazione
Identified device Dispositivo identificato
Seleziona l'oggetto che vuoi
controllare con
MOD: il pulsante
KW8010 MOD: KW8012
ID: 00B4765D Dispositivo identificato ID: 00B4765D
Cucina Tabletop lamp Lampada tavolo
Kitchen MOD: KW8012 Cucina
Choosetavolo
Lampada the pushbutton to be ID: 00B4765D Scegli il pulsante da associare
associated to the Kitchen Light 1 con Luce Cucina 1 di Piano terra -
19 of the Ground floor - Kitchen
Cappa
19 Cucina 19
e Scegli il pulsante da associare
a- 2 con Luce Cucina 1 di Piano terra - 2
Piano cottura Cucina Configurazione salvata
Hob 3 luci
Kitchen Cucina
1
Veletta
1
1
Soggiorno

invert the key order inverti ordine tasti

Lampada piantana
Advanced settings Impostazioni avanzate
OK OK OK
Lampada lettura

Save the configuration Salva configurazione

Cancel Annulla Annulla
Lampadario

Activation
Presa TVof the MyHOME_Up system - Customisation of the functions by the user
definition of the LIGHT command for the - definition of the FULL command for the
control
Bagnoof two lights. control of 2 separate light points.

Lampada piantana

Lights and automation MyHOME_Up 51

WWW.BTICINO.COM
 GENERAL FEATURES

Light and shutter automation system

LIVING NOW DIGITAL CONTROL DEVICES WITH AMAZON ALEXA VOICE ASSISTANT

The “Voice command” device, item KG/KS/KM8013, for “voice” control of the home automation functions of
brings together the functions of two digital controls for MyHOME, and to request any information, news, weather
the management of lights with cyclical ON/OFF mode, conditions, timetables, and so on, using the Amazon
with an integrated voice assistant exploiting the Amazon Alexa platform.
Alexa technology. The integration of the voice activated controls with
The advantage resulting from the use of this device is the MyHOME_Up system is ensured using the
clear: the installer can offer to their customer an added MyHOMEServer1 device.
value service, setting “by default” each room of the home

Voice control
KG8013

Light control Area with voice Light control

assistant

Voice control power supply Rear clamp for power 27 Vd.c. power supply
supply 110–240 Va.c. contacts for connection
The BUS 27 Vd.c. power supply is supplied to the voice module or actuators
27 Vd.c. power
command device by the connection module, item K8001, supply contacts
through the electrified frame, item 8103/P1, or item for voice control
8104/P.
In addition to the above module, it is also possible to use
the extra flush mounted 2 module power supply, item
K8003.
For further details, see the technical sheets of the
power supply and voice control.

Power supply item K8003

52
Installation features
The voice command is installed in the respective
flush mounted box and support, item K470... using an
appropriate “frame” with 27 Vd.c. power supply contacts.
Therefore, use connection module item K8001 to connect
the BUS cable to the electrified frame.

Blanking module
K4950

Electrical
contact

Connection
1 modules

Electrified frame

Voice control

Lights and automation MyHOME_Up 53

WWW.BTICINO.COM
 GENERAL FEATURES

Light and shutter automation system

LIVING NOW 1-MODULE DIGITAL ACTUATORS

These devices can be used with digital controls and are
available in two versions: Load manual control
pushbutton
- for the ON/OFF control of two lamps;
- for the control of a shutter electrical motor.
Both devices are flush mounted using the K470... support and
are equipped with side contacts for the 27 Vd.c. electric power
supply input directly from the connection module, or through Electric power supply
a second actuator. input side contact.
The association with the corresponding digital control
requires the MyHOME_Up application. Rear clamps for
load connection

Blanking
module


Connection
module
Actuator

2
Electrified frame

3
Digital controls
and/or blanking modules

54
CONTROL DEVICES WITH KEY COVERS
They are completed with two types of keys and key covers:
- With 1 function, one or two modules, to be used with the grey control key;
- With 2 functions, one or two modules, to be used with the black control.
All the devices have luminous indications, which can be adjusted or excluded, for the
notification of the status of the load, and so that they can be seen in the dark.

Upper pushbutton
Lower pushbutton

LED

Control key Control key Control key

Key cover Key cover Key cover Key cover

1 function 2 functions 1 function 2 functions
1 module 1 module 2 modules 2 modules

The control with single key cover can be compared The control with double key cover (rocker) can, on the other hand, can be compared with
with a traditional closing contact (pushbutton or a traditional exchange contact.
switch). NOTE: the control keys are supplied with the device.

Lights and automation MyHOME_Up 55

WWW.BTICINO.COM
 GENERAL FEATURES

Light and shutter automation system

OTHER CONTROL DEVICES

8-key multifunction control item H/LN4652

With 8 backlit keys, this device manages lighting, the
automation of shutters and, in integrated systems,
also the audio NUVO player system and the scenarios.

Control item H4652

Presence and lighting sensors

item ....4658 and item ....4659
Devices with passive infrared ray presence sensors,
ultrasound and light sensors, for the management
of lighting based on the presence of people and
the amount of natural light, in compliance with the
requirements of the highest energy efficiency class for
buildings, as contemplated by European Standard EN
15232.

Passive IR movement sensor (PIR)

item AM4659

Glass controls with capacitive sensors

The mechanical keys are replaced by capacitive
sensors which are touch activated. They can be
identified by LED with light of adjustable intensity.
The functions that can be managed are the same as
for the 8-key multifunction control.
Nighter 3-module control
item HS4657M3

Whice 4-module control

item HD4657M4

56
CONTACT INTERFACES
Contact interface
These devices integrate the traditional control in DIN module
equipment (switch, pushbutton, etc.) in the MyHOME_ item F428
Up BUS system and allow their use in rooms where
traditional systems are already present or in historic
and prestigious rooms whereby the complete or partial
remaking of the electric system would entail heavy
masonry work. Contact interface
in basic module
item 3477

Lights and automation MyHOME_Up 57

WWW.BTICINO.COM
 GENERAL FEATURES

Light and shutter automation system

SELECTION OF THE CONTROL DEVICE BASED ON THE FUNCTION TO MANAGE

Basic control Special control LIGHT digital FULL digital control

control

PERFORMED FUNCTIONS H4652/2 H4651M2 KW/KG/KM8010 KW/KG/KM8011

L4652/2 L4651M2
AM5832/2 AM5831M2
H4652/3
L4652/3
AM5832/3
K4652M2

Cyclical ON/OFF

ON/OFF control with

light intensity control
LIGHTING
General, room,
group controls

Timed controls

Normal UP/DOWN
and safe UP/DOWN
AUTOMATION mode shutter control
General, room, group
controls

SCENARIO
MANAGEMENT

58
8-Key control Brightness and movement/ Nighter e Whice capacitive Contact interface
presence sensor control

H/LN4652
HC/HD/HS4658
HC/HD/HS4659
L/N/NT4658 HD4657M3/4
L/N/NT4659 HC4657M3/4
BMSE3001 HS4657M3/4
BMSE3003
048834
K4659 F428 3477

Lights and automation MyHOME_Up 59

WWW.BTICINO.COM
 GENERAL FEATURES

Light and shutter automation system

FLUSH MOUNTED ACTUATORS

The range of MyHOME_Up includes devices for ON/OFF or dimmer control of lighting bodies with powers up
to 2300 W, of the type:
- LED;
- fluorescent;
- halogen;
- incandescent;
- supplied with ferromagnetic or electronic transformers;
- ballast 1-10V;
- DALI.
Below are some actuators; for the complete range and the technical features see the “Catalogue” section.

Devices to be finished with key covers - flush mounted installation

Upper pushbutton
Lower pushbutton

LED

Control key

Control key

Key cover
1 function
2 modules Remote Key cover
actuator 2 functions
“control” 2 modules
Light key cover
management
“actuator”
key cover

Actuator, item LN4672M2 Livinglight with 1 x 10 A relay for 4 A

incandescence lamps, for fluorescent lamps or ferromagnetic
transformers, and 500 W for LED and compact fluorescent lamps, for
automation and/or load control management functions.

60
Basic modularity devices - flush mounted installation

Basic actuators installed side by side

Box

Actuator, item 3476 with 1 relay

for single loads: 2 A resistive or
BUS incandescence lamps, 2 A inductive for
BUS Traditional device Support
ferromagnetic transformers. Preset
input
for connection with NO type control
pushbutton.

DIN modular devices

Dimmer actuator, item F418U2 two-channel dimmer for the

management of dimmer LEDs, dimmer compact fluorescent
lamps (CFL), energy saving halogen lamps and electronic
transformers at 110-230V.
IT is possible to connect two channels with parallel connection,
to increase the maximum power that can be managed.

ON/OFF actuator, item BMSW1003 with “Zero Crossing”

technology, 4 independent outputs for 16 A maximum loads at
230 V a.c. The device is powered directly from the 100/240 Va.c.
mains 50/60 Hz.

Lights and automation MyHOME_Up 61

WWW.BTICINO.COM
 GENERAL FEATURES

Light and shutter automation system

ACTUATORS FOR SHUTTERS AND CURTAINS

Different actuators are available for the motor-driven control
of shutters and/or curtains with powers up to 460 W:

L1
M L2
L

Actuator F411U2 M = AC motor with 2 windings

L1-N = clockwise rotation
L2-N = anticlockwise rotation

Actuator, item LN4672M2 to be

completed with key covers, for the
control of one shutter or 2 lights.

Actuator, item F411U2 with 2 relays for ON/OFF lighting

control. In the diagram, the device is wired for the control
of a motor-driven shutter, and must be set in “relay
interlock” mode.

Pushbutton UP
MQ01016-a-IT 27/04/2015

Actuators with164
preset and position
calibration function
Devices with 2 interlocked relays for the control
of standard motors with automatic calibration,
standard with manual calibration, and pulse motors.
Available in all the flush mounted civil versions and
2 DIN module versions, to be used with the specific
control device.

Preset function: STOP button Pushbutton DOWN

In addition to the UP/DOWN monostable and bistable
functions, these devices allow to move the shutter to
a specific position (Preset).

Flush mounted actuator, item H4661M2 and DIN rail actuator,

item F401, for shutter control with storage of the desired position.

62
SIZING OF THE SYSTEM The length of the cable must also - For optimum division of the
When sizing the system, check the be considered, complying with the currents on the bus line, it
absorption of the devices to ensure following rules: is recommended that the
correct system operation. With - The length of the connection power supply is installed in an
absorption levels below 600 mA, between the power supply and intermediate position.
it will be possible to use compact the furthest device must not
power supply E49. With absorption exceed 250 m.
levels between 600 and 1200 mA, - The total length of the
power supply E46ADCN must be connections must not exceed
used. 500 m (laid out cable).
For the current absorption of the
device see its technical data sheet. ON

OFF

With power supply E46ADCN: A

A = 250 m max

B = 250 m max B
E46ADCN
A + B = 500 m

NOTE: If a UTP5 cable is used in alternative to the L4669 1

1
2 3
2
4 5
3 4 5

BUS cable, distances are halved. C1 C2 C3 C4

NOTE: For the sizing of the lighting system with light and movement/presence sensors,
refer to the technical data sheets of the products available at the bticino.com website
and the homesystems-legrandgroup.com website.

Lights and automation MyHOME_Up 63

WWW.BTICINO.COM
 WIRING DIAGRAMS

Light and shutter automation system

DIAGRAM 1
SWITCHING ON AND OFF OF 2 LAMPS WITH 4 LIGHT POINTS WITH GENERAL ON/OFF CONTROL

N
L

E46ADCN H4672M2 ON
L1 H4672M2 ON
L2

OFF OFF

230 Va.c. BUS BUS To other

devices

H4652/2 ON H4652/2 ON ON

GEN

OFF OFF OFF

DIAGRAM 2
AUTOMATIC SWITCHING ON OF THE LIGHT WITH PASSIVE INFRARED CEILING SENSOR

N
L

E46ADCN 3476 L L1
1 1

ART. 3476
230V ˜
2A cosϕ = 0,6
2A

230 Va.c. BUS To other

devices

HD4659 H4652/2 ON

For other
functions
OFF

The device controls the load with the address indicated in A and PL. When a presence is detected, if the light level is below the set level the device
switches on the assigned load and keeps it on for a period of time set using the configurator in T. The sensitivity of the PIR movement sensor is set
using the configurator in S. For correct operation, it will be necessary to set the sensor lighting setpoint (see procedure).

64
DIAGRAM 3
ALTERNATE CURRENT MOTOR CONTROL FOR SHUTTERS, CURTAINS, OR MOTORISED SHUTTERS

N
L N N N

M1 M2 M3
L1 L2 L1 L2 L1 L2

F411U2 F411U2 F411U2

E46ADCN

230 Va.c.
BUS
To other
devices

L1-N = clockwise rotation H4652/3 H4652/2

L2-N = anticlockwise rotation
GEN
M = AC motor with 2 windings

DIAGRAM 4
SWITCHING ON AND OFF OF ONE LAMP AND SHUTTER CONTROL USING AN ACTUATOR
CONTROL

N
L
L1
E46ADCN L L1 L2
M
1 1

ART. 3476

N 230V ˜
2A cosϕ = 0,6
2A

L2

H4672M2(*) 3476
230 Va.c. BUS

To other
* Complete the device with key covers as per the drawing: devices

ON

Shutter control Light control

OFF

Lights and automation MyHOME_Up 65

WWW.BTICINO.COM
 WIRING DIAGRAMS

Light and shutter automation system

DIAGRAM 5
SWITCHING ON, OFF AND ADJUSTMENT OF THE LIGHT LEVEL OF FLUORESCENT LAMPS
THROUGH “BALLAST”

N
L 230 Va.c.
L
+

F413N

Ballast 1 2 NC 3 4
-+
0-10V
ART. F413N

E46ADCN
N L - + C1

230 Va.c.
BUS
To other
devices

H4652/2 ON For other functions

OFF

DIAGRAM 6
SWITCHING ON, OFF AND ADJUSTMENT OF THE LIGHT LEVEL OF LED LAMPS

N
L

DIN
dimmer
E46ADCN actuator

F418U2

230 Va.c.
BUS To other
devices

ON

H4652/2 For other functions

OFF

66
DIAGRAM 7
LIGHTING SYSTEM WITH PRESENCE AND LIGHTING SENSORS - LARGE MEETING ROOM
The SCS 1-10 V dimmer, item the room for optimum detection, and the blackboard (circuit 3) and
BMDI1002, manages all the room automatically disables the general the general lights (circuit 1), are
lighting circuits: switching on/off lighting of the room (circuit 1) based managed using the 3 module SCS
the lamps of the screen (circuit 2) on the detection of presence and the control, item H4652/3.
and the blackboard (circuit 3), and level of natural light. The shutters (circuit 5, 6 and 7) and
adjusting the general lighting of the It is also possible to manually adjust the screen up and down control
room (circuit 1). the light using one of the 3 module (circuit 2) are controlled by three SCS
The SCS double technology sensor, SCS control buttons, item H4652/3, actuators, item F411/2, and adjusted
item BMSE3003, configured in ECO installed at the entrance. using the special SCS control, item
mode, is installed at the centre of The lights of the screen (circuit 2), H4651M2.

L L
N N
Motor for Motor for Motor for Motor for Central 1 Halogen for 1 Halogen for
shutters shutters shutters screen lamps 10 x 72 W screen blackboard

7 6 5
4 1 2 3

Item Item Item Item Item BMDI1002 Item E46ADCN

F411U2 F411U2 F411U2 F411U2 N L N L
230 V 230 V
SCS cable

Item Item Item

H4652/3 H4651M2 BMSE3003

Warning:
1. To ensure optimum detection, install the 3. Connect together all the devices using 5. The sensor has the following factory
double technology ceiling SCS sensor, the SCS cable, item L4669, L4669/500, settings: delay time 15 minutes, brightness
item BMSE3003, at the centre of the room; L4669HF. threshold 500 lux, maximum PIR sensitivity
install the three module SCS control, item 4. Configure sensors, controls and controller and high US. Whenever necessary
H4652/3; install the special SCS control, using the MyHOME_Suite software. use the configuration remote control
item H4651M2, between the screen and the item BMSO4001 to change the sensor
shutters. parameters.
2. Install the 2-channel SCS actuators item
F411U2 + the 1-10 V 4 channel dimmer,
item BMDI1002 + the SCS power supply
unit, item E46ADCN, in a cabinet.

Lights and automation MyHOME_Up 67

WWW.BTICINO.COM
 WIRING DIAGRAMS

Light and shutter automation system

DIAGRAM 8
LIGHTING SYSTEM WITH PRESENCE AND LIGHTING SENSORS - HALL AND RECEPTION
Each passive infrared ceiling amount of natural light: sensors are
sensor, item BMSE3001, or double configured to keep a 500 lux level in
technology sensor, item BMSE3003, the reception and a 100 lux level on the
controls the corresponding zone staircases.
(circuit 1, 2 and 3). The light can also be switched on using
During the day, the illumination is the touch screen, item H/LN4890.
automatically adjusted based on
presence or movement, and the

L1
L2
N
Circuit 1 Circuit 2 Circuit 3

230 V 230 V 230 V

NL N L N L

Item
E49 Item Item
F417U2 F416U1
BUS/SCS cable

Item
LN4890
Item Item Item
BMSE3001 BMSE3003 BMSE3003

1. Install the double technology or passive 3. Install the SCS touch screen, item LN4890, 6. The sensors have the following factory
infrared SCS ceiling sensors, items on the wall. settings: delay time 15 minutes, brightness
BMSE3003 and BMSE300, at the centre of 4. Connect all the devices together using threshold 500 lux, maximum PIR sensitivity
each of the areas to control. the SCS cable, item L4669, L4669/500, and high US.
2. Install the SCS power supply unit, item L4669HF. Whenever necessary use the configuration
E46ADCN, and the SCS dimmers, items 5. Configure all the installed devices using the remote control item BMSO4001 to change
F417U2 and F416U1, in the hall patch MyHOME_Suite software. the sensor parameters.
cabinet.

68
CONTENTS
MyHOME_Up – Temperature control

General features. . . . . . . . . . . . . . . . . . 70
General rules for installation. . . . . . . . . . . 76
Wiring diagrams . . . . . . . . . . . . . . . . . . 78

Energy Management MyHOME_Up 69

WWW.BTICINO.COM
 GENERAL FEATURES

Temperature control

The MyHOME temperature control With the installation of the With the integration of the Driver
system includes the following MyHOMEServer1 gateway, the manager, item F459, it is possible
devices: system can also be managed to manage third-party heating and
- Probes with and without display using the HOMETOUCH touch cooling systems using the mentioned
- Actuators screen, or the Smartphone with devices.
the MyHOME_Up App.
IT is also possible to define
programs for the activation of the
heating system based on custom
profiles.
HOMETOUCH 7”

Zone 1 Zone 2
Power supply probe probe

Actuator for 0-10 V 8 relay

solenoid valves actuator

MyHOMEServer1

Cold
M
0-10V
Hot

OTHER BRAND SYSTEMS

- MITSUBISHI ELECTRIC
- DAIKIN
- HITACHI
- SAMSUNG
- ..............

Driver manager F459

70
THE PROBES

Probe with display IT is possible to automatically

Fitted with front controls for switch OFF the heating if a window
the selection of the desired is opened in a room managed by
temperature and of the operating the probe. This condition, notified
mode: automatic, manual, preset by the opening of the NC type
Eco, comfort, Antifreeze-thermal contact, is detected by the probe,
protection and OFF. which transfers the information to
In systems with fan-coil, it is also the temperature control system,
possible to set the fan speed, and it for the appropriate actions. Living
can be used in mixed systems with Now probes, item KW/KG/KM4691,
are internally equipped with a Probe item KG4691
both heating and cooling functions.
It can be connected to a NC/NO humidity probe, the measured value
window contact, useful for changing of which can be used for advanced
the operating modes based on applications possible thanks to the
the status (open or closed) of the integration with third-party systems
window itself. through Driver manager, item F459.

Basic probe without display for different applications (e.g.s to

Device for the installation of junction change the operating mode when a
boxes, to be combined with an window is open, and to change the
external temperature sensor, item operating function...).
3457, for the measurement of the The probe is also equipped with
room temperature in the 0 - 40 °C a mechanical pushbutton for the
range. configuration of the device and 2
In addition to the SCS clamp used LEDs, one red and one green, which
for connection to the SCS bus, and provide information on the correct
the PROBE clamp for the connection installation and configuration of
of the external temperature sensor, the device, and the status of the
the probe also has a REMOTE clamp temperature control zone. Basic probe item 3454
for connection to a remote contact

Probe without display It can be used with slave probe

Flush mounted probe to measure configuration for operation in
the temperature between 3 – 40°C. conjunction with the probe with
The device has no temperature display, item .....4691, or as master
adjustment knobs, which makes probe.
it suitable for installation in public
places /small service sector.

SLAVE probe item HC4693

Energy Management MyHOME_Up 71

WWW.BTICINO.COM
 GENERAL FEATURES

Temperature control

THE ACTUATORS
Manufactured for installation in DIN switchboards, these devices control
the solenoid valves and the pumps of the temperature control system.
The range is below:

Actuator
With NA contact relay output, with 2 contacts
item F430/2
item F430/2 (2 contacts), item F430/4 (4 contacts) and item F430R8
(8 contacts), for the control of ON/OFF valves and pumps. If the
system includes fan-coils, the fan speed can also be adjusted.

OUT 3
OUT 2
OUT 1
OUT 5
OUT 4
N

L
L1 L2

OUT 3
OUT 2
OUT 1
N
OUT 5
OUT 4
F430R8

Use of the F430/8 actuator, for the control of a 4-tube and 3-speed fan-coil.

72
With output voltage 0-10 V
item F430R3V10 (also with 3 NC contacts) and item F430V10, for the control of proportional solenoid valves,
type 0-10.

OUT 3
OUT 2

M 0 – 10 V OUT 1
N

M 0 – 10 V L
L1

OUT 3
OUT 2
OUT 1
N

–
5
+
6

–
7 F430R3V10
+
8

Use of the F430R3V10 actuator for the control of one 4-tube fan-coil with 0-10 3-speed valves.

Energy Management MyHOME_Up 73

WWW.BTICINO.COM
 GENERAL FEATURES

Temperature control

SELECTION OF THE DEVICES BASED ON THE SYSTEM TO CONTROL

Actuators

1 2 3 4 1 2 3 4 5
1 2 3 4 1 2 3 4 5

ART. F430/2 ART. F430/4

C1 C2 C1 C2 C3 C4

F430/2 F430/4 F430R8

ON/OFF

OPEN/CLOSE
VALVES
3 POINTS

0-10V

2 ON/OFF TUBES

4 ON/OFF TUBES

FAN-COIL 2 TUBES 3 POINTS

4 TUBES 3 POINTS

2/4 TUBES 0-10V

ELECTRICAL HEATING

CLIMAVENETA

MIXED ON/OFF + FAN-COIL

Note 1): Changing the speed using the probes is not possible

74
 Probes

F430R3V10 F430V10 H4691 3454 SLAVE PROBE

LN4691 HC/HS4693
KW4691 L/N/NT4693
KG4691
KM4691

1)

1)

1)

Energy Management MyHOME_Up 75

WWW.BTICINO.COM
 GENERAL RULES FOR INSTALLATION

Temperature control

SIZING OF THE SYSTEM The length of the cable must also

When sizing the system, check be considered, complying with the 1 2 3 4

following rules:
1 2 3 4

the absorption of the devices to

ART. F430/2

- The connection length between

C1 C2

ensure correct system operation.

With absorption levels below the power supply and the
600 mA, it will be possible to furthest device must not exceed
A
use compact power supply E49. 250 m.
With absorption levels between - The total length of the
connections must not exceed B
600 and 1200 mA, power supply E46ADCN
E46ADCN must be used. 500 m (cable extended).
- For optimum division of the 1 2
1 2 3 4
3 4

For the current absorption of

ART. F430/2

currents on the bus line it C1 C2

the device see its technical data

is recommended that the
sheet.
power supply is installed in an
intermediate position. With power supply E46ADCN:
A = 250 m max
B = 250 m max
A + B = 500 m

Note: if a UTP5 cable is used in alternative to

the L4669 BUS cable, distances are halved.

SYSTEM PHYSICAL
EXPANSION
Particularly extended systems,
or systems with overall device 1 2 3 4

absorption exceeding 1200mA

1 2 3 4

ART. F430/2

supplied by power supply C1 C2

E46ADCN, can be split into

several sections powered with
their own power supply unit
and connected to each other in
“physical separation” mode using
the F422 interface configured in
“physical expansion” mode. F422 F422

When sizing the system, consider

OUT OUT

AR T.F422 AR T.F422

that:
- It is not possible to connect two
interfaces in parallel on the
same BUS;
- It is possible to install up to 4
interfaces to split the system
into 5 separate sections.

MyHOMEServer1

For further indications refer

to the technical data sheet of MyHOMEServer1
the F422 interface, available
at bticino.com Example of temperature control system integrated with the light and shutter automation system.

NOTE: devices are

automatically configured by the
MyHOMEServer1 web server.

76
 ASSOCIATION OF THE DEVICES
This operation defines:
- the logic link between a probe and the corresponding actuator that must be managed;
- the operating mode of probes and actuators based on the type of temperature control system to manage.

As for the light and shutter automation system, this function is carried out when putting the system into operation
and using the MyHOMEServer1 web server and the MyHOME_Up smartphone App.

For the list of the devices compatible with this mode, refer to the APPENDIX section at the end of the guide.

Actuator
H/LN4691

F430R3V10 Probe
ZONE 4 Ground... Kitchen Ground... Kitchen

Actuator Identified device

H/LN4691 MOD: F411/4 Associated devices
ID:00D16020 Light - Kitchen 1
Ground floor - Kitchen

Choose the channel to be associated

with Ground Floor Kitchen Light 1 - F411/4 - ID:00D16020 - Channel 1
A
Kitchen No label
B

F430R3V10 Probe No associated

ZONE 3 1 2 3 4
control/input

OK Add device

Actuator Cancel End

H/LN4691
Setup of the parameters of the
BUS probe with display, item LN4691.

F430R3V10 Probe
ZONE 2

Actuator
FAN-COIL
LAN network H/LN4691 SYSTEM
E46ADCN

Probe
MyHOMEServer1

F430R3V10
ZONE 1
MyHOMEServer1 Power supply

Energy Management MyHOME_Up 77

WWW.BTICINO.COM
 WIRING DIAGRAMS

Temperature control

DIAGRAM 1
4 ZONE VILLA - HEATING BY MEANS OF RADIATOR WITH 0-10 V SOLENOID VALVES

- + - + - + - +
OUT 1OUT 2 OUT 1OUT 2

Actuator Actuator

Probe F430V10 F430V10

0 to 10
Solenoid valve ZONE 4 H/LN4691

Probe

0 to 10 BUS
Solenoid valve ZONE 3 H/LN4691

Probe
MyHOMEServer1
E46ADCN
0 to 10
Solenoid valve ZONE 2 H/LN4691 MyHOMEServer1

Probe Power supply

0 to 10
Solenoid valve ZONE 1 H/LN4691

L Actuator
N
1 2 3 4
1 2 3 4

ART. F430/2

C1 C1 C2

F430/2

Circulation
pump
Boiler

WARNING: The diagrams, showing Axolute and Livinglight, also apply, when possible, to MyHOME_Up products, Living Now series.
For further information, see the Technical sheets of every item available in the bticino.com site.

78
DIAGRAM 2
4 ZONE VILLA - HEATING BY MEANS OF RADIATORS WITH ON/OFF SOLENOID VALVES

C4 C3 C2 C1

F430/4
1 2 3 4 5
1 2 3 4 5

H/LN4691 ART. F430/4

Actuator
C1 C2 C3 C4

ZONE 4 Probe
Solenoid valve

H/LN4691

ZONE 3 Probe
Solenoid valve

BUS

H/LN4691
MyHOMEServer1
ZONE 2 Probe E46ADCN
Solenoid valve
MyHOMEServer1

H/LN4691
Power supply
Probe
ZONE 1
Solenoid valve

1 2 3 4
1 2 3 4

ART. F430/2

C1 C2
Actuator

F430/2

L
N
C1

Circulation
pump
Boiler

Energy Management MyHOME_Up 79

WWW.BTICINO.COM
 WIRING DIAGRAMS

Temperature control

DIAGRAM 3
4-ZONE VILLA - HEATING AND COOLING WITH 4-TUBE FAN-COILS, WITH 0-10V SOLENOID
VALVES OR WITH 0-10 SPEED ADJUSTMENT.

Actuator
H/LN4691

F430R8 Probe
ZONE 4

Actuator
H/LN4691

F430R8 Probe
ZONE 3

Actuator
BUS
H/LN4691

F430R8 Probe
ZONE 2

Actuator FAN-COIL SYSTEM

H/LN4691

E46ADCN

F430R8 Probe
ZONE 1

Power supply

Boiler

Chiller

Note: 0-10V valves are not managed in proportional mode, but in ON-OFF mode

80
Actuator connection

F430R8

2
M 3
0 to 10 4
1

M L1
0 to 10
N
M

5
6

Variation for the connection of a 4-tube fan-coil with 0-10 V speed adjustment
- use of two 0–10 V outputs (set LOAD = 3 in case of physical configuration).

M N

Control
M unit
VC
VH
-+ -+ COM
H 0 – 10 V C
VH= heating valve
VC= cooling valve
COM= common entrance

F430R3V10

Energy Management MyHOME_Up 81

WWW.BTICINO.COM
 WIRING DIAGRAMS

Temperature control

DIAGRAM 4
3-ZONE VILLA - INTEGRATION OF THE TEMPERATURE CONTROL SYSTEM WITH RADIANT
PANEL HEATING SYSTEMS AND DAIKIN VRV COOLING (IP PROTOCOL)

F430/4
1 2 3 4 5

Daikin VRV
1 2 3 4 5

ART. F430/4

internal unit C1 C2 C3 C4

C1 C2 C3 C4

ZONE 3
H/LN4691
VRV internal unit MODE

Dill-Net
FAN

ZONE 2
H/LN4691
VRV internal unit
MODE

Dill-Net FAN

ZONE 1
H/LN4691
VRV internal unit
MODE

Dill-Net FAN

C1
Intelligent F430/2
Touch Controller 1 2 3 4
1 2 3 4

E46ADCN
ART. F430/2

C1 C2

Dill-Net

SCS
Switch
Ethernet
Mixing
valve
C1

LAN M
Driver
manager
F459
ETHERNET

SCS AI SCS AV

SCS
L
N

In these systems the Daikin local controllers must not be installed.

82
CONTENTS
MyHOME_Up - Load control and consumption display
General features. . . . . . . . . . . . . . . . . . 84
Wiring diagrams . . . . . . . . . . . . . . . . . . 89

Energy Management MyHOME_Up 83

WWW.BTICINO.COM
 GENERAL FEATURES

Management and load control system

The load control Management system manages the maximum power used, by automatically disconnecting the
least important appliances in case of overload.

OPERATION In the example shown, the oven, The microwave is on the other
The control unit measures the the microwave and the washing hand the appliance with the highest
power absorbed by the connected machine represent the loads importance, with priority level 3, and
loads and compares it with the controlled through actuators, while only disconnects after the oven and
preselected value (between 1.5 and the refrigerator, the operation of the washing machine.
18 kW, with tolerance +/- 20%). which must never be stopped, is The status of the disconnected
connected to the socket without appliance is displayed on the
Each load to control is associated
actuator. 7” HOMETOUCH touch screen
with an actuator managed by the
control unit, which disconnects the In case of overload, the first and on the digital controls, item
load from the network in case of appliance that disconnects is the KW/KG/KM8011, through LED
overload. least important one; in this example pictograms.
this is the oven, which has a priority The device can be reactivated
The load disconnection sequence
level of 1. using the button of the actuator,
can be configured during
installation; it is possible to manage using the 7” HOMETOUCH touch
up to 63 priority levels (actuators). screen, and the digital controls,
item KW/KG/KM8001.
If after reactivation the overload
Central unit for load
management persists, the control unit
disconnects the loads with priority
levels 2 and 3, until the overload
Electrical counter situation is resolved,
HOMETOUCH
Electrical switchboard

BUS SCS

Uncontrolled Flush mounted Flush mounted Flush mounted

sockets actuator actuator actuator

230 Va.c.

Uncontrolled Priority 1 Priority 2 Priority 3

load controlled controlled controlled
load load load
NOTA: the load control management central unit is positioned inside the electrical switchboard.

84
Consumption display and energy production

An important function offered by MyHOME_Up is the

possibility of real time display and filing of the home
energy consumption data.
The measurement is carried out using toroid electricity
meters, item F520. The display is through the Photovoltaic
Smartphone and the MyHOME_Up App. panel

Inverters

Compact Electric power

power supply meter

Ground floor Kitchen +

Music

Coloured light

Light

Rolling shutter

MyHOME_Up App

Energy Management MyHOME_Up 85

WWW.BTICINO.COM
 GENERAL FEATURES

Load control and consumption display

CONTROL AND MEASUREMENT DEVICES

Electricity meter item F520 with 3 toroid Central unit for load management art. F521
inputs Device for the measurement of the power absorbed by
The device measures up to three separate electricity the electric system, and the management of the load
lines through the corresponding measurement toroids. management system actuators.
The intended processing and accounting functions are: The control unit manages up to 63 appliances or electric
- Instantaneous consumption or production of maximum loads for each phase, making available the following
3 lines; data:
- Instantaneous consumption or production on hourly - instantaneous consumption of the controlled line;
basis for the last 12 months, on daily basis for the last - cumulative consumptions on hourly basis for the
2 years, on monthly basis for the last 12 years. last 12 months, on daily basis for the last 2 years, on
monthly basis for the last 12 years.
Data cancel
pushbutton
230 Va.c.
connection 230 Vac
connection

Device Device status Load forcing

status LED LED pushbutton
Toroid supplied
as standard with
connection cable
Configurator
socket door

SCS/BUS
connection

Configurator
socket door
SCS/BUS
connection

Flush mounted 16A actuator item ....4672N

Flush mounted device with internal 10A relay for load
control management and/or automation. Local pushbutton
Load control mode manages the load disconnection for load/control
local forcing
priority based on the settings of the load control unit,
item F521.
A front pushbutton allows to:
- force the priority of the load during normal operation.
In this case the central unit cannot disable the load Load status red
for 4 hours. LED
- re-enable a load disabled by the central unit (the
duration of this operation lasts for 4 hours, unless the
disabling key is pressed manually). Device status
two-colour LED
In light automation mode, it carries out all the operational
activities that can be configured on the control devices,
with the exclusion of shutter control.

86
16A actuator with current sensor item F522
Device equipped with 1 10A bistable relay with zero 230 Va.c.
crossing functionality for the load control management connection
and/or automation functions, with the same modes of the
flush mounted actuator, item .....4672N.
The actuator can be used for the measuring of the
electricity, as it is fitted with an internal current sensor for
Device status
the measurement of the consumptions of the controlled LED
Load forcing
load and, in conjunction with the external optional toroid,
pushbutton
item 3523, for the measurement of the earth leakage
current of the diagnostic system.
Configurator
socket door

16A actuator item F523

Device equipped with 1 bistable relay with zero crossing
functionality for the load control management and/or
automation functions, with the same modes of the flush
mounted actuator, item .....4672N. SCS/BUS
connection

Central unit for load management item F522.

The device has a similar construction to actuator F523.

DEVICE SELECTION
Available functions Devices
Energy meter Central unit Actuator 16A 16A actuator Flush
item F520 for load with current item F523 mounted Living Now Full control
management sensor 16A item ...8011 and
item F521 item F522 actuator Touch screen
item HOMETOUCH
...4672N

Display

Load control

Diagnosis 1)
Note 1): in combination with optional toroid 3523

Energy Management MyHOME_Up 87

WWW.BTICINO.COM
 GENERAL FEATURES

Load control and consumption display

SIZING OF THE SYSTEM

The maximum number of devices If the system shares the same cable When sizing the system, it is also
in a system depends on the total of the Automation/Temperature necessary to consider the length of
absorption of the same and the control system, the calculation of the cable, complying with the follow-
distance between the point of the maximum number of devices ing rules:
connection and the power supply. must be completed taking into - The connection length between
With absorption levels below account the general absorption of the power supply and the furthest
600 mA, it will be possible to use the same. device must not exceed 250 m.
compact power supply E49. With
For the purpose of the above - The total length of the connections
absorption levels between 600 and
calculations, refer to the absorption must not exceed 500 m (cable
1200 mA, power supply E46ADCN
values indicated on the technical extended).
must be used.
data sheets of the devices, available - For optimum division of the
in the on-line catalogue that can be currents on the bus line it
found at bticino.com. is recommended that the
power supply is installed in an
intermediate position.

A = 250 m max
A B = 250 m max
A + B =500 m
Maximum current provided by the power supply:
B 1200 mA for item E46ADCN and 600mA for item E49.
Power supply
Note: If a UTP5 cable is used in alternative to the L4669
BUS cable, distances are halved.

88
WIRING DIAGRAMS

Management and load control system

DIAGRAM 1 - MANAGEMENT AND LOAD CONTROL

CAUTION

A It is possible to install the following flush

mounted 2-module 16A actuators:
- HC/HS/HD4672N AXOLUTE
- L/N/NT4672N LIVING/LIGHT/LIGHTECH

B The TMG circuit breakers must be selected

based on the load absorption.

C The IG general circuit breaker (TMG+EARTH

N LEAKAGE) must be selected based on the
L N general absorption. For better safety and
comfort it is recommended to install also the
L
STOP&GO additional device.

D Supplied with each F521 is a 3523 toroid for the

reading of the current
C Thermal magnetic
circuit breakers
Thermal
magnetic earth-
leakage circuit
breaker
IG B
N
L
Toroid for
D
reading
3523

Load
Load Load

L N
...4672N
Central unit
for load Actuator Actuator HOMETOUCH
E49 management 16 A 16 A A 3488
PRI
F521 F523 F523 A = 0
Compact
A = 0 A = 0
E49
PRI: 220 – 240 V~
185 – 175 mA
50/60 Hz

power supply A1 = 0 PL = 0
PL = 0 PL = 0
SCS: 27 Vdc

G = 0
600 mA

A2 = 0
SCS
G = 0 G = 0 M = 0
A3 = 1
M = 0 M = 0 P1 = 0
P = 0
P1 = 0 P1 = 0 P2 = 3
HST = 5
P2 = 2 P2 = 1

BUS/SCS

Switchboard or Electric panel

Energy Management MyHOME_Up 89

WWW.BTICINO.COM
 WIRING DIAGRAMS

Management and load control system

DIAGRAM 2 - THREE-PHASE LOAD CONTROL MANAGEMENT AND SINGLE PHASE LOAD
WITH BUS SCS IN COMMON
380 Va.c.
R R
S S
C T T
N N

MGT1 MGT2 MGT2

Single Single
R N phase phase
load load

E49 F521 F523 F522 D F523

PRI

E49
PRI: 220 – 240 V~
185 – 175 mA
50/60 Hz
SCS: 27 Vdc

A3 = 1 P2 = 1 P2 = 2 P2 = 3
600 mA

PHASE R PHASE 1 PHASE 1 PHASE 1

SCS

BUS

F521 F523
Energy display
R N
H/LN4710
TIME

A3 = 2 P2 = 1
PHASE S PHASE 2

FC4A...

F521 F523

Three-phase load
A3 = 2 P2 = 1 NOTE: 1) configurators must be selected
based on the contract power.
PHASE T PHASE 3

CAUTION

A The thermal magnetic circuit breakers must be

selected based on the load absorption.
B The contactor must be selected based on the
load absorption
C The three-phase line must be balanced
D F522: to be positioned where the single-phase
load must be measured

90
 MyHOME_Up - Function integration

Function integration MyHOME_Up 91

WWW.BTICINO.COM
 GENERAL FEATURES

Function integration

The integration of the various home automation The integration also allows to control all the home
functions allows to set advanced functions that could automation functions through central control
not be possible with a traditional system. devices, such as the HOMETOUCH Touch Screen, or a
Smartphone with the MyHOME_Up supervision App.
For example it is possible to: With MyHOME_Up it is possible to have two types of
- create advanced functions, such as switching on all integration:
the lights following an intrusion alarm;
- create scenarios for the simultaneous activation of
several devices of the MyHOME_Up system for the
creation of comfort situations.

HOMETOUCH

Integrated MyHOME_Up
functions

Digital control with Digital control

integrated Amazon
Alexa voice assistant
Ground floor Kitchen +

Music

Coloured light

Light

Rolling shutter

MyHOME_Up APP

92
1. Integration of two or more MyHOME_Up functions, such as the light
automation system with the temperature control system, or the load
management system.

2. Integration of two or more MyHOME_Up functions with other BTicino

and/or third party systems, possible using the LAN network and the
TCP-IP communication protocol, or dedicated interfaces. An example is
represented by the integration of the Automation system with the radio-
wired Burglar Alarm system, or with the NUVO digital audio system.
They can also be integrated with third-party products, such as air
conditioning systems, Philips Hue lamps, etc...

NUVO audio system Burglar alarm

Other brand systems

Air conditioning
systems

Driver manager F459

Lighting with RGB lamps

MyHOMEServer1

Management of
weather stations
and sensors

Function integration MyHOME_Up 93

WWW.BTICINO.COM
 GENERAL FEATURES

Function integration

INTEGRATION OF LIGHT AUTOMATION, LOAD

MANAGEMENT, CONSUMPTION DISPLAY AND
TEMPERATURE CONTROL SYSTEMS
The integration is achieved without the use of special interfaces, as
the devices share the same BUS cable and electric power supply.

Light Shutter control Temperature Temperature

control probe probe

230 Va.c. BUS SCS

TV/SAT IPTV
Energy
Automation Management

automazione diffusione sonora antifurto termoregolazione videocitofonia controllo lan controllo carichi energia luci tvcc www irrigazione

Dimmer 2 relay Temperature control Temperature control

actuator actuator actuator actuator

Ground floor Kitchen +

Lights Shutters Radiator Radiator

Music

Coloured light

Light

Rolling shutter

MyHOME_Up APP WiFi Modem router MyHOMEServer1 for control with Smartphone
and MyHOME_Up app

94
“Physical separation” mode
In case of need of splitting the system in order to
achieve the current absorption values, or to keep them
separate, interface F422 must be used in “physical
separation” mode.

With this mode, each system can be connected both to the

OUT and the IN clamp of the F422 interface used to keep
the corresponding BUS separate, and the electric power
supplies independent.
The interface operating mode will be set automatically
from MyHOMEServer1 the first time the system is
switched on.
F422 interface

Energy
management
system

Automation
system

Power supply Automation

system

Energy Power supply

management
system
230 Va.c.
OUT

F422 interface

230 Va.c.
IN

Ground floor Kitchen +

Music

WiFi Modem router Coloured light

Light

MyHOMEServer1 for control with Smartphone Rolling shutter

and MyHOME_Up app

MyHOME_Up APP

Function integration MyHOME_Up 95

WWW.BTICINO.COM
 GENERAL FEATURES

Function integration

INTEGRATION OF MyHOME_Up SYSTEMS WITH BTICINO AND/OR THIRD PARTY SYSTEMS

MyHOME is an open system that A. Using the F422 interface or the D. Using integration devices
can be easily integrated, without HOME TOUCH touchscreen, for with different communication
any modifications, with the best the integration of the automation protocols, such as DALI, etc.;
technologies, and with systems and and temperature control system
devices of other manufacturers.
E. Developing API based
with the video door entry system.
applications supplied by BTicino
The integration is completed in the
following ways:
B. Using the MyHOMEServer1 through the “Works With
gateway based integration Legrand” program.
platform.
C. Using the MyHOME_Link
integration platform based
on the use of the F459 Driver
manager and the TCP/IP
communication protocol.

A.1 Use of interface item F422

For the integration of the two This device makes it possible to For more information, see the
systems shown, interface F422 use some Automation devices for CONNECTION DIAGRAMS -
must be configured in “galvanic the activation of Video door entry VARIATIONS sections of the design
separation” mode (configurator 0 in functions, such as switching a light guide for BTicino 2 wires audio and
the MOD position); or a camera on. video door entry systems.

Video door
Power supply entry system

SCS interface
OUT MOD=0 Light Shutter Temperature Temperature
230 Va.c. control control probe probe

IN

230 Va.c.
BUS SCS
TV/SAT IPTV

Dimmer 2 relay Temperature Temperature control

actuator actuator control actuator actuator

automazione diffusione sonora antifurto termoregolazione videocitofonia controllo lan controllo carichi energia luci tvcc www

Ground floor Kitchen +

Lights Shutters Radiator Radiator

Music

WiFi Modem router Automation Energy Management

Coloured light

Light

Rolling shutter

MyHOMEServer1 for
control with Smartphone
MyHOME_Up APP and MyHOME_Up app

96
A2. Use of HOMETOUCH Touch Screen
When managing home automation The MyHOMEServer1 gateway must
and video door entry system also be installed in the system, for
functions using the HOMETOUCH the integrated management of the
touch screen, interface F422 is not Automation, Temperature control
required. and Video door entry system for the
In this case, the integration is association of the devices.
completed from HOMETOUCH Function control can be completed
connected to the Automation and locally or remotely using the
Video door entry system BUS. Smartphone, with the MyHOME_Up
and Door Entry Apps.

Light Shutter Temperature Temperature

control control probe probe HOMETOUCH

230 Va.c. BUS SCS

TV/SAT IPTV

Dimmer 2 relay Temperature Temperature control

actuator actuator control actuator actuator Video door
entry system
automazione diffusione sonora antifurto termoregolazione videocitofonia controllo lan controllo carichi energia luci tvcc www irrigazione

Lights Shutters Radiator Radiator

Automation Energy Management

Ground floor Kitchen +

Music

WiFi Modem router

Coloured light

Light

MyHOMEServer1 for Rolling shutter

control with Smartphone

and MyHOME_Up app
MyHOME_Up APP

Function integration MyHOME_Up 97

WWW.BTICINO.COM
 GENERAL FEATURES

Function integration

INTEGRATION OF MyHOME_Up SYSTEMS WITH BTICINO AND/OR OTHER PARTS SYSTEMS

B. Use of Gateway item MyHOMEServer1

The use of MyHOMEServer1 allows In addition to the control of all the of several systems; for example,
the integration of automation, functions using the Smartphone when activating the Burglar alarm
temperature control and video door and the MyHOME_Up App, and system when leaving the house, it is
entry system with other BTicino the HOMETOUCH touch screen, it possible to set the temperature at an
systems or third party systems, will be possible to create Smart economy level, closing the shutters
such as the burglar alarm, coloured scenarios resulting from the synergy and switching the lights off.
lights and sound diffusion.
As shown in the diagram below, the Central unit Keypad

integration of these systems takes

place through the LAN network and
with the TCP/IP communication Expansion modules

protocol. The Burglar alarm system 4-conductor cable BUS

is already preset for the connection
to the LAN network, while for the
connection of the Automation
and/or Temperature control
systems it is necessary to use the Multipolar
cable
MyHOMEServer1 gateway. Volumetric sensors

Burglar alarm
Volumetric sensors

Light Shutter Temperature Temperature

control control probe probe

Siren

BUS SCS
230 Va.c.
Dimmer 2 relay Temperature Temperature control
actuator actuator control actuator actuator

LAN network

Lights Shutters Radiator Radiator

Automation Energy Management

HOMETOUCH

Ground floor Kitchen +

Music

Coloured light

Light

Video door
Rolling shutter

LAN network
entry system
MyHOME_Up APP
WiFi Modem router
MyHOMEServer1 for control
with Smartphone and
MyHOME_Up app
98
 This page shows another example of integration through the LAN
network of Automation, Temperature control, NUVO multiroom audio
system, and lighting with Philips HUE lamps.

Philips HUE lamps and gateways

1-zone player

Light Shutter Temperature Temperature

control control probe probe

BUS SCS
230 Va.c. NUVO player

Dimmer 2 relay Temperature Temperature

actuator actuator control actuator control actuator

LAN network

Lights Shutters Radiator Radiator

Automation Energy Management

HOMETOUCH
Ground floor Kitchen +

Music

Coloured light

Light

Rolling shutter

LAN network
MyHOME_Up APP

WiFi Modem router

MyHOMEServer1

Function integration MyHOME_Up 99

WWW.BTICINO.COM
 GENERAL FEATURES

Function integration

INTEGRATION OF MyHOME_Up SYSTEMS WITH BTICINO AND/OR OTHER PARTS SYSTEMS

C. Integration by means of Driver manager gateway item F459

This integration solution uses temperature control system, VRV, For technical information, details
the Driver manager, item F459, VRF and air conditioning systems and a view of all the available
appropriately configured with the of the main manufacturers on the drivers, visit: www.bticino.com
specific driver, specifically made to market. The F459 device can be
manage functions/systems of third- programmed with several drivers,
party manufacturers. for the management of several
It is for example possible to systems integrated with MyHOME.
manage, through the MyHOME zone

Specific driver
for application

Other brand systems

Driver manager F459
■ MITSUBISHI ELECTRIC
■ DAIKIN
BUS SCS LAN network
■ HITACHI
■ PHILIPS HUE
■ DMX
■ NETATMO

MyHOME_Up ■ SAMSUNG
■ OREGON SCIENTIFIC
■ ...........

D. Integration by means of dedicated interfaces

The MyHOME_Up catalogue also includes the F429 interface for the integration of the DALI protocol.

To the DALI
devices
Power supply
Actuator

230 Va.c.

MyHOME_Up
system

100
E. Integration using the Application Programming Interface (API)

API integration can be made in two This is the open interoperability For more details please
ways: platform, a strategic part of the Eliot visit: www.bticino.com
- interoperability through the program (program of the connected
sharing of different languages on objects of the Legrand group).
the IP level (local and through the Compatible with the main IoT world
cloud). players, it gives the possibility
- interoperability through IOT Cloud of connecting with the Legrand
platforms, for example Artik ecosystem in several ways, allowing WORKS WITH
Samsung and similar. small and large developers to
Works With Legrand is available for interact with MyHOME_Up.
professionals that must use this
integration solution.

Function integration MyHOME_Up 101

WWW.BTICINO.COM
 GENERAL FEATURES

MyHOME _Up – Software and Services

102
GENERAL FEATURES

Home configurator Web App

The HOME configurator is a tool - MyHOME_Up BUS, and to which can be changed at any time,
that helps the installer or the customise the control/device points and saved in the MyBTicino personal
final use to correctly estimate in the various finishes: Axolute, area. If the system is a MyHOME_Up
an electric system, either Màtix, Livinglight and Living Now. system, also the total system current
traditional, traditional with With this simple information, the consumption will be supplied, for
connected Smart devices, or application will provide the value for the appropriate checks at the design
MyHOME_Up BUS. the total system, or split into rooms, stage.
The application, available after
free registration on the
https://my.bticino.it website,
offers a range of “standard
homes” that can be modified
based on specific needs. For each
home the functions to value can
also be defined.
- Driving force and services;
- Light;
- Shutters;
- Temperature control;
- Consumption display;
- Electric panel;
- Protections.
After selecting the function, the
application requires the definition
of the system technology:
- traditional;
- traditional with connected
Definition of the functions to value.
Smart devices;

Example of system estimation.

NOTE: to ensure constant product improvement, this software may be subjected to revision.
We therefore recommend that the my.bticino.it website is checked regularly to make sure to obtain the most recent version of the web application.

Software and Services MyHOME_Up 103

WWW.BTICINO.COM
 GENERAL FEATURES

YouDiagram software

YouDiagram is the software for

the design and configuration of
2 wires video door entry systems
Example of YouDiagram software screenshot
and wired-radio burglar alarm
systems.
It allows to draw the system
diagram, select the finish of the
devices and their configuration.
It also quickly provides the total
value of the current absorption of
the system, for the appropriate
design checks.

The software can be downloaded free of charge from the website

https://professionisti.bticino.it/software-e-app/software-di-progettazione/

Example of a video door entry system design

NOTE: to ensure constant product improvement, this software may be subjected to revision.
We therefore recommend that the my.bticino.it website is checked regularly to make sure to obtain the most recent version of the web application.

104
MyHOME_SUITE

MyHOME_Suite is the application that can be used in alternative to the MyHOME_Up App to assign functions
to the devices of the Automation, Energy management and Temperature systems.

The connection of the system to the PC can be completed using

the MyHOMEServer1 web server.
The software can be easily downloaded free of charge from the
website www.homesystems-legrandgroup.com

On-line
update Icon for the consultation Web Server IP address
icon of the software integrated and connection status
user guide display

List of Working area for the collection of the Selection of the parameters for the
configurable system devices to configure configuration of the address and the
items operating mode

Software and Services MyHOME_Up 105

WWW.BTICINO.COM
 GENERAL FEATURES

Service and digital tools

CUSTOMER SERVICE

TECHNICAL-COMMERCIAL INFORMATION ESTIMATION SERVICE TECHNICAL SUPPORT SERVICE

Toll-free number for the request of To request detailed estimates regarding Authorized Technical Support Centres
technical documentation and technical MyHOME_Up applications, including to request assistance for products and
and commercial documentation, integrated applications. systems with or without warranty.
available For more information see the “Services”
From Monday to Friday 8:30 to 18:30 section in the following site:
www.professionisti.bticino.it.

WEBSITES FOR PROFESSIONALS

A wide range of content to get to know the BTicino range better.

MYOPEN COMMUNITY
The home automation system
integrator community, with detailed
information and services relating to
new applications.
www.myopen-legrandgroup.com

BTICINO.COM ON LINE CATALOGUE

Visiting www.bticino.com, it will be The quickest way to find
possible to acquire all the product technical information and the
information and the technical content prices of our products.
that will help you to improve your https://catalogue.bticino.com/prbt/
knowledge of the BTicino offer. bticino/wiring-devices/living-now/
living-now-my-home-up

106
CONTENTS
MyHOME_Up catalogue . . . . . . . . . . . . . . . . 108

MyHOME FLATWALL catalogue. . . . . . . . . . . 126

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Catalogue MyHOME_Up 107

 INTEGRATION AND CONTROL

MyHOMEServer1 3488 F429

Item CONTROL SERVER USING THE APP Item SCS/DALI INTERFACE

MyHOMEServer1 server to associate devices during the system F429 DALI dimmer, 8 independent outputs with
starting-up and for the local and remote maximum load 16 ballast at 230 Vac, pushbutton
management of the functions by the user with for load direct control - 6 DIN modules
the specific MyHOME_Up application for Android
and iOS smartphones or tablets. DRIVER MANAGER
F459 integration platform with other brand systems -
MyHOMEServer1 KIT 6 DIN modules
MHSERVERKIT kit containing MyHOMEServer1 and Access Point
for communication between the MyHOME_ Contact the BTicino System Integration Service to check the feasibility of specific
Up system to which it is connected, and a integrations and to request the licence needed to use the Driver manager
smartphone or tablet where the MyHome-Up (Toll free number 800.837035)
App is installed.
Note: For the details of the products managed by MyHome_Up and the compatible
products, see the corresponding guide.
HOMETOUCH - TOUCH SCREEN 7”
3488W HOMETOUCH - Touch Screen 7” for the management
3488 of all MyHOME_Up functions, that can be
integrated with the video door entry system, to
be used as connected internal unit. To use the
home automation functions, configuration is not
necessary. It is possible to display the MyHOME_Up
system status and control the integrated functions
(lights, automation, scenarios, burglar alarm,
temperature management, Nuvo music system,
...). Thanks to the “DOOR ENTRY for HOMETOUCH”
application, available both for Android and iOS
operating systems, it is also possible to manage
the video door entry functions of a BTicino 2
wires system using the 7” capacitive display or the
Smartphone. Flush mounted installation with box
for masonry walls (item 3487) or wall mounted
installation with the supplied metal bracket.
Available in tech grey and in white.

BOX FOR FLUSH MOUNTED INSTALLATION

3487 box for flush mounted installation of the
HOMETOUCH Touch screen item 3488 and 3488W.
Width 197 mm, height 148 mm and depth 52 mm.
3487AP support for flush mounted installation on
plasterboard walls of the HOMETOUCH Touch
screen
item 3488 and 3488W.

108
NOTE: White device Tech device Anthracite device Neutral item
LIVING NOW DIGITAL DEVICES FOR LIGHTS AND SHUTTERS

KG8013 K8003 KM8010 KW8011 KG8100 KW8103

K8002L K8002S K8001

Item VOICE CONTROL Item BLANKING MODULE.

KW8013 Amazon Alexa digital control device with voice KW8100 covers for blanking modules item K4950 - 1
KG8013 assistant, including two capacitive controls for KG8100 module
KM8013 lighting management. KM8100
27 Vd.c. power supply from BUS through
connection module item KW8001 or additional ELECTRIFIED FRAME
power supply unit, item K8003 - 3 modules KW8102P1 electrified frame with intermediate control
KG8102P1 separators (removable). For the installation of
KM8102P1 up to 3 digital controls or covers, item KW/KG/
POWER SUPPLY KM8100 in 2-module box with support K8102
K8003 voice command additional power supply unit, electrified frame with intermediate control
KW8103
item KW/KG/KM8013 - 2 modules separators (removable). For the installation of
KG8103
KM8103 up to 3 digital controls or covers, item KW/KG/
KM8100 in 3-module box with support K4703
LIGHT CONTROL KW8103P1 electrified frame with intermediate control
KW8010 capacitive control for the management of one KG8103P1 separators (removable). For the installation of
KG8010 or two controlled socket and light ON/OFF type KM8103P1 up to 4 digital controls or covers, item KW/KG/
KM8010 functions. It can also be used to manage 4 KM8100 in 3-module box with support K4703
protected scenarios - 1 module KW8104 electrified frame with intermediate control
KG8104 separators (removable). For the installation of
FULL CONTROL
KM8104 up to 4 digital controls or covers, item KW/KG/
KW8011 capacitive control for the management of one KM8100 in 4-module box with support K4704
KG8011 to three functions among the following: on/
KW8104P1 electrified frame with intermediate control
KM8011 off, dimmer, coloured lights, up/down without
KG8104P1 separators (removable). For the installation of
preset, scenarios, Nuvo multi-room sound
KM8104P1 up to 5 digital controls or covers, item KW/KG/
system and load control. It can also be used as
KM8100 in 4-module box with support K4704
group or general control. On-board proximity
sensor that allows the display of function icons
when approaching the control - 1 module

ON/OFF ACTUATORS FOR LIGHTS AND FOR

SHUTTERS
K8002L actuator with 2 independent relays for single or 2-MODULE SUPPORT FOR ELECTRIFIED FRAME
double 230 V a.c. loads: 16 A - 1 module ITEM ....8102P1
K8102 support for the installation of the electrified frame
K8002S shutter actuator with 2 internal relays 2 A 250 item .....8102P1 in 2 module box
Va.c. In addition to the monostable and bistable
UP/DOWN function, the actuator also places the
shutter in a stored (PRESET) position - 1 module

CONNECTION MODULES
K8001 device for the power supply of controls through
electrified frame
item KW/KG/KM8103......8104.....

Catalogue MyHOME_Up 109

NOTE: White device black device sand device Neutral item
 LIGHTS AND SHUTTER AUTOMATION

H4651M2 L4652/2 AM5832/3 K4652M2 H4652 HS4680

Item CONTROLS FOR SINGLE OR DOUBLE LOADS Item CONTROL FOR SPECIAL FUNCTIONS
control which can drive a single actuator for control for the management of one or two ON/
single or double loads or two actuators for OFF functions, the shutter UP/DOWN function
single loads or independent double loads – to and the adjustment of a dimmer load. It can also
be completed with 1 2-module key cover for be used as scenario control and for the call to the
controls with one or two functions or 2 1-module floor, staircase light switching on and door lock
key covers with one or two functions - 2 modules activation functions. It manages advanced shutter
H4652/2 Axolute functions. - 2 modules.
L4652/2 Livinglight To be completed with 1 or 2-module covers.
K4652M2 Living Now
AM5832/2 Màtix
control which can drive three actuators for single
or double loads or two actuators for single loads Control for the management of up to three
or independent double loads – to be completed separate functions as described above - 3
with 3 1-module key covers for controls with one modules. To be completed with 1 or 2-module
or two functions - 3 modules covers.
H4652/3 Axolute K4652M3 Living Now
L4652/3 Livinglight
AM5832/3 Màtix

CONTROL FOR SHUTTER MANAGEMENT SCENARIO CONTROL

2 module flush mounted control with reduced customisable scenario control for the activation
thickness with 3 pushbuttons. In addition to of up to 4 Automation, Temperature Control and
monostable and bistable UP/DOWN operation, Sound System independent scenarios saved in the
the device also places the shutter in a stored F420 scenario module - 2 modules.
(PRESET) position. H4680 Axolute
Axolute HC4680
H4660M2
HS680
only suitable for operation with advanced
actuators H4661M2 and F401, specific for the N4680 Livinglight
management of shutters. NT4680
LN4660M2 Livinglight L4680
only suitable for operation with advanced 8-KEY control for light management, shutter
actuators LN4661M2 and F401, specific for the automation, sound system and scenarios - SCS-
management of shutters. BUS connection - sizes: 2 modules
Màtix H4652 Axolute
AM5860M2
only suitable for operation with advanced LN4652 Livinglight
actuators LNAM5860M2 and F401, specific for
the management of shutters. A5 sheets for the customisation of the control symbols
item H4652 and LN4652.
The sheets can be customised using the tool found in the
CONTROL FOR SPECIAL FUNCTIONS MyHOME_Suite configuration software.
special control – can drive an actuator 3541 black
performing all the standard functions of a 3542 white
control and in addition some special functions:
activation of 4 scenarios, timings, activation of
an actuator installed on a different bus than the HOME-AUTOMATION HINGE
control, selection of the fixed adjustment level Livinglight
4911TDM
and the dimmer soft-start and soft-stop speed, accessory for the installation of 2-module key
sound system, door lock switching on control,
covers on devices installed in 503E box
call to the floor and switching on staircase light
control and management of auxiliary channels.
To be completed with 1 or 2-module key covers
with one or two functions - 2 modules
H4651M2 Axolute
L4651M2 Livinglight
AM5831M2 Màtix

110
NOTE: White device Tech device Anthracite device Neutral item
LIGHTS AND SHUTTER AUTOMATION

HD4657M3 HS4657M3 MHKIT1116

Item GLASS CONTROLS Item CONTACT INTERFACE

Axolute 3477 basic module control interface with 2
MyHOME control which can control single loads independent contacts for the control of 2
or group loads (e.g. lights and shutters), sound actuators for single function loads, or 1 actuator
system, scenario, basic door entry functions (e.g. for double function loads (shutters) – the inputs
gate opening). It has capacitive keys, which are accepts two traditional switches or pushbuttons
touch activated. They can be identified by LED with NO and NC contact, or a traditional two-way
with light of adjustable intensity. switch, or interlocked pushbuttons
WHITE GLASS F428 as above - 2 DIN modules
HD4657M3 6-key control– size: 3 modules

HD4657M4 8-key control– size: 4 modules MEMORY MODULE

F425 module for saving the status of the actuators -
to reset the light Automation system in case of
WHICE blackout - 2 lowered DIN modules
HC4657M3 6-key control– size: 3 modules
KIT - SHUTTER AUTOMATION
HC4657M4 8-key control– size: 4 modules MHKIT1013 solution for the automation of shutters.
It gives the possibility of controlling 5 motorised
shutters or curtains, or mixed shutter/curtain
NIGHTER solutions, with individual and general controls.
HS4657M3 6-key control– size: 3 modules The kit includes:
• 1 power supply item E49
• 1 shutter control item LN4660M2
HS4657M4 8-key control– size: 4 modules • 5 shutter actuators item LN4661M2
• key covers with UP/DOWN and STOP symbols
• various configurators.
NOTE: for white glass controls check contact your local BTicino commercial It can be expanded with other similar actuators
representative for availability or integrated with other MyHOME functions.
LIVINGLIGHT aesthetic (White, Tech, Anthracite
finishes)
KIT - LIGHT AND SHUTTER AUTOMATION
INSTALLATION OF THE GLASS MHKIT1116 solution for the control of 6 shutters or 6 lights
Box Support Control
DIGITAL CONTROL Box 503E H4703 HD4657M3 and 3 shutters, or 12 light points, with general
HC4657M3 and individual controls.
HS4657M3 It is possible to save the shutter position. The kit
504E H4704 HD4657M4 includes:
HC4657M4 • 1 power supply item E49
HS4657M4 • 1 shutter control item L4652/2
• 6 shutter actuators item LN4672M2
• various configurators. To be completed with
Support LIVINGLIGHT key covers. It can be expanded with
other MyHOME devices that share the BUS cable,
item L4669.
Note: the following products are not included in the package and have to be purchased
separately:
- cable (sheathed pair) art. L4669 sold in 100 m coil;
- flush and wall mounted boxes, supports and front cover plates of the LIVINGLIGHT range.

Control

Catalogue MyHOME_Up 111

NOTE: White device Tech device Anthracite device Neutral item
 LIGHTS AND SHUTTER AUTOMATION

H4672M2 K4672M2L 3476 K4672M2S

LN4672M2
AM5852M2
Item LIGHT AND SHUTTER CONTROL/ACTUATOR Item LIGHT CONTROL/ACTUATOR
actuator/control with 2 independent relays - for actuator/control with 2 independent relays - for
single, double or mixed loads: 1380 W resistive, single, double or mixed loads: 1380 W resistive,
1380 W incandescence lamps, 460 W for reducer 1380 W incandescence lamps, 460 W for reducer
motors, 460 VA cosϕ 0.5 for ferromagnetic motors, 460 VA cosϕ 0.5 for ferromagnetic
transformers and 250 W for fluorescent lamps - transformers and 250 W for fluorescent lamps.
logic relay interlock via configuration. The device The device can be also configured to manage a
can be also configured to manage a remote remote actuator - 2 modules.
actuator - 2 modules. K4672M2L Living Now
H4672M2 Axolute
LN4672M2 Livinglight
AM5852M2 Màtix
SHUTTER CONTROL/ACTUATOR
2 module flush mounted actuator with 2
LIGHT CONTROL/ACTUATOR internal relays and 4 pushbuttons. In addition to
3476 1 relay actuator - for single loads: 2 A resistive monostable and bistable UP/DOWN operation,
or incandescence lamps, 2 A cosϕ 0.5 for the actuator also places the shutter in a stored
ferromagnetic transformers - a traditional (PRESET) position.
pushbutton with NO contact accepted in input Axolute
H4661M2
to be combined with control devices H4660M2
LN4661M2 Livinglight
to be combined with control devices LN4660M2
AM5861M2 Màtix
to be combined with control devices AM5860M2
K4672M2S Living Now

LOADS THAT CAN BE DRIVEN (230 Va.c. 50/60 Hz)

Actuators Type

Energy saving LED lamps Linear fluorescent Compact fluorescent Electronic transformers Ferromagnetic Reducer motors
incandescence and lamps 1) lamps 3)
transformers 2) 3) for shutters 4)
halogen lamps
H4672M2 1380 W 250 W 250 VA 250 W 460 W 460 VA 460 W
LN4672M2 Max 2 lamps Max 2 lamps
AM5852M2
K4672M2L
3476 2A 40 W - 40 W - 2 A cosφ 0,5 -
460 W Max 1 lamp - Max 1 lamp - 460 VA -
H/L4661M2 - - - - - - 2 A 250 Va.c.
AM5861M2
K4672M2S
Notes:
1) Power factor corrected fluorescent lamps, discharge lamps.
2) Account must be taken of the transformer yield to calculate the effective power of the load connected to the actuator. For example if a dimmer is connected to a 100 VA ferromagnetic
transformer with yield 0.8, the effective power of the load will be 125 VA.
3) The transformer must be loaded at its rated power and however never less than 90% of this power. It is preferable to use a single transformer rather than several transformers in
parallel. For example it is better to use a single 250 VA transformer with 5 50W spotlights connected rather than use 5 50 VA transformers in parallel each with a 50 W spotlight.
4) The symbol on the actuators refers to the shutter reducer motors.

112
NOTE: White device Tech device Anthracite device Neutral item
LIGHTS AND SHUTTER AUTOMATION

F411U2 F411/4 BMSW1003 F401

Item ACTUATORS FOR CENTRALISATIONS Item ACTUATORS FOR CENTRALISATIONS

F411U2 actuator with 2 independent relays – for BMSW1003 ON/OFF actuator, 4 independent outputs
single and double loads: 10 A resistive and 6 A with maximum load 16 A at 230 Va.c.,
incandescence lamps, 500 W for reducer motors, clamp connection and RJ45, IP20 protection
2 A cosϕ 0.5 for ferromagnetic transformers index, power supply 100/240 Va.c. 50/60 Hz,
and 250 W for fluorescent lamps - logic relay pushbuttons for load direct control - zero-
interlock via configuration - it has ¨Zero crossing¨ crossing function - 6 DIN modules
technology - 2 DIN modules BMSW1005 ON/OFF actuator, “Zero Crossing” technology, 8
F411/4 actuator with 4 independent relays - for independent outputs with maximum load 16 A
single, double or mixed loads: 2 A resistive, 2 A at 230 V a.c., clamp connection, IP20 protection
incandescence lamps, 500 W for reducer motors, index, power supply100/240 V a.c. 50/60 Hz,
2 A cosϕ 0,5 for ferromagnetic transformers and pushbuttons for load direct control - 10 DIN
70 W for fluorescent lamps - logic relay interlock modules
via configuration - 2 DIN modules
F401 actuator with 2 internal relays and 4 pushbuttons.
In addition to monostable and bistable UP/DOWN
operation, the actuator also places the shutter in
a stored (PRESET) position - 2 DIN modules

LOADS THAT CAN BE DRIVEN (250 Va.c. 50/60 Hz)

Actuators Type

Energy saving incandescence LED lamps Linear fluorescent Compact fluorescent Electronic transformers Ferromagnetic Reducer motors
and halogen lamps lamps 1) lamps 3)
transformers 2) 3) for shutters 4)
F411U2 10 A 250 W 4A 250 W 4A 4 A cosφ 0,5 2A
1380 W Max 4 lamps 230 W Max 4 lamps 230 W 460 VA 460 W
F411/4 2A 70 W 0.3 A 70 W 0.3 A 2 A cosφ 0,5 2A
460 W Max 2 lamps 70 W Max 2 lamps 70 W 460 VA 460 W
BMSW1003 16 A 2.1 A 10 X (2 X 36 W) 1150 W 16 A 16 A -
3680 W 500 VA 4.3 A 5A 3680 W 3680 W -
BMSW1005 16 A 2.1 A 4.3 A 5A 16 A 16 A -
3680 W 500 VA 10X2X36 W 1150 VA 3680 W 3680 W -
F401 2 A 250 Va.c.

Notes:
1) Power factor corrected fluorescent lamps, discharge lamps.
2) Account must be taken of the transformer yield to calculate the effective power of the load connected to the actuator. For example if a dimmer is connected to a 100 VA ferromagnetic
transformer with yield 0.8, the effective power of the load will be 125 VA.
3) The transformer must be loaded at its rated power and however never less than 90% of this power. It is preferable to use a single transformer rather than several transformers in
parallel. For example it is better to use a single 250 VA transformer with 5 50W spotlights connected rather than use 5 50 VA transformers in parallel each with a 50 W spotlight.
4) The symbol on the actuators refers to the shutter reducer motors.

Catalogue MyHOME_Up 113

NOTE: White device Tech device Anthracite device Neutral item
 LIGHTS AND SHUTTER AUTOMATION

F413N BMDI1002 F429 F416U1 F418U2

Item DIMMERS FOR CENTRALISATIONS Item MULTI-LOAD DIMMERS FOR CENTRALISATIONS

F413N 1-output dimmer to supply fluorescent lamps or F416U1 multi-load dimmer, 1 output with maximum
LED sources with input 1-10 V for single loads up load 4.3 A at 230 Va.c., clamp connection and
to 2.5 A at 230 Va.c. – type of screw connection - RJ45, IP20 protection index, power supply
power supply 27 Vd.c. – absorption 30 mA – max 100/240 Va.c. 50/60 Hz, pushbutton for load
10 ballast that can be connected (clamps 1-2) - direct control - 6 DIN modules
with pushbutton for load direct control - version F418U2 two-channel dimmer for the management of
for fastening on DIN rail - 2 modules dimmer LEDs, dimmer compact fluorescent
BMDI1002 1/10V dimmer, “Zero Crossing” technology, 4 lamps (CFL), energy saving halogen lamps and
outputs with maximum load 4.3 A at 230 V a.c., electronic transformers at 110-230V. Possibility
clamp connection, IP20 protection index, power of parallelisation of the two channels to increase
supply100/240 V a.c. 50/60 Hz, pushbuttons for the maximum power which can be managed.
load direct control - 10 DIN modules
power supply 27 Vd.c., absorption 18 mA - version
F429 DALI dimmer with 8 independent outputs for for fastening on DIN rail - 4 modules
the connection of up to 16 DALI reactors for each
output – 230 V a.c. power supply 50/60 Hz; 110
- 240 Vd.c. – absorption 5 mA - with pushbutton
for load direct control - version for fastening on
DIN rail - 6 modules

LOADS THAT CAN BE DRIVEN (230 Va.c. 50/60 HZ)

Actuators Type

Energy saving incandescence LED lamps Linear fluorescent lamps 1) Compact fluorescent Electronic Ferromagnetic Reducer motors
and halogen lamps lamps transformers 3) transformers 2) 3) for shutters 4)
BMDI1002 Dimmer for ballast - 4 x 4.3 A outputs - 4x 1000VA@ 230 Vac - 4x500VA@ 230 Vac
F413N - - 2 A 460 W 5) - - - -
- - Max 10 ballast, type T5, T8, - - - -
compact or driver for LED
F414 0.25 - 4.3 A - - - - 0.25 - 4.3 A -
60 - 1000 VA - - - - 60 - 1000 VA -
F416U1 4.3 A - - - 4.3 A 4.3 A -
40 - 1000 W - - - 40 - 1000 W 40 - 1000 W -
F418U2 2x300 W 2x300 VA - 2x300 VA 2x300 VA 2x300 VA -
F429 SCS/DALI dimmer interface - 8 x16 ballast

Notes:
1) Power factor corrected fluorescent lamps, discharge lamps. 2) Account must be taken of the transformer yield to calculate the effective power of the load connected to the actuator.
For example if a dimmer is connected to a 100 VA ferromagnetic transformer with yield 0.8, the effective power of the load will be 125 VA.
3) The transformer must be loaded at its rated power and however never less than 90% of this power. It is preferable to use a single transformer rather than several transformers in
parallel. For example it is better to use a single 250 VA transformer with 5 50W spotlights connected rather than use 5 50 VA transformers in parallel each with a 50 W spotlight.
4) The symbol on the actuators refers to the shutter reducer motors. 5) Only compatible with lamps with 1/10 V ballast.

114
NOTE: White device Tech device Anthracite device Neutral item
 LIGHT SENSOR

HD4658 L4658N AM5659 K4659

Item PIR+US DOUBLE TECHNOLOGY GREEN SWITCH Item PIR PASSIVE INFRARED GREEN SWITCH
Green Switch: double technology presence Green Switch: passive IR (PIR) sensor, suitable
sensor, passive IR and ultrasound (PIR+US), for the detection of presence in transit areas
suitable for the detection of presence in (corridors, toilets, service rooms). Operating mode
working areas (offices, meeting rooms). With (automatic or manual), time delay (5 s to 59min),
manual ON/OFF pushbutton. Operating mode and brightness threshold (20 to 1275 LUX)
(automatic or manual), time delay (5 s to 59 settable using the advanced/basic (BMSO4001/
min), and brightness threshold (20 to 1275 LUX) BMSO4003) configuration remote control;
settable using the advanced/basic (BMSO4001/ physical or virtual configuration. 2 modules
BMSO4003) configuration remote control; HD4659 Axolute
physical or virtual configuration. 2 modules HC4659
HD4658 Axolute HS4659
HC4658 N4659N Livinglight
HS4658 NT4659N
N4658N Livinglight L4659N
NT4658N AM5659 Màtix
L4658N K4659 Living Now
AM5658 Màtix

DIAGRAM FOR THE USE OF THE GREEN SWITCH, ITEM L/N/NT4658N ECO MODE
Manual load activation and automatic switch off managed by the
Green Switch dimmer/actuator based on the detection of the presence of people
Power supply control item Dimmer item F416U1
L4658N and the desired level of illumination detected by the control, item
L4658N. The function of the control is first of all to activate the automatism of
the dimmer/actuator: upon first pressure, the sensor compares the desired light
level with the actual light level of the room, and ascertains if the light should be
switched on or not. A subsequent pressure of the control forces the switching ON
Lighting devices or OFF of the automatism determined by the dimmer/actuator.

230 Va.c. 2 BUS

Catalogue MyHOME_Up 115

NOTE: White device Tech device Anthracite device Neutral item
 LIGHT SENSOR

BMSE3001 BMSE3003 0 488 34

Item LIGHTING/MOVEMENT SENSORS BMSO4001 BMSO4003

BMSE3001 passive infrared SCS sensor for the detection
of movement and the lighting level. Ceiling
flush mounted installation using springs or
installation boxes; surface installation using
surface installation box, item 048875; IP20 Item CONFIGURATION REMOTE CONTROLS
protection index; RJ45 clamp connection; 8 m BMSO4001 the advanced configuration remote control, with IR
(50 m2) diameter coverage area for a 2.5 m transmitter and receiver, adjusts the main operating
installation height, maximum installation height parameters of: Switch Sensor, Green Switch and SCS
6 m; 27 V d.c. power supply from bus, absorption compatible sensors. With display for the acquisition of
12 mA; regulation with basic/advanced remote the parameters set on the sensors and to modify them.
control (BMSO4003 and BMSO4001) or through
configuration software, of the lighting level, Batteries charged by USB mini port.
from 5 to 1275 LUX, of the time delay, from 30 s BMSO4003 the basic configuration remote control, with IR transmitter,
to 255 h, and of the main operating parameters; adjusts the main operating parameters of: Switch Sensor,
Push&Learn pushbutton Green Switch and SCS compatible sensors. Modification
BMSE3003 double technology SCS sensor: passive infrared of parameters only possible for preset values, battery
for the detection of presence and the lighting recharge not available
level. Ceiling flush mounted installation using
springs or installation boxes; surface installation
using surface installation box, item 048875; IP20
protection index; RJ45 clamp connection; 8 m INSTALLATION ACCESSORIES
diameter (50 m2) infrared coverage area for a 2.5 048875 ceiling mounted box compatible with the sensors: BMSE3001
m installation height, 11 mm diameter (95 m2) and BMSE3003, IP20 protection index, dimensions Ø 100 x
ultrasound coverage area for a 2.5 m installation 50 mm
height, maximum installation height 6 m; 27
V d.c. power supply from BUS, absorption 17 048971 angle installation accessory, compatible with the 048834
mA; regulation with basic/advanced remote accessory, IP42 protection index, dimensions (hxlxd) 115 x
control (BMSO4003 and BMSO4001), or through 75 x 40 mm
configuration software, of the lighting level,
from 5 to 1275 LUX, of the delay, from 30 s to
255 h, and of the main operating parameters;
Push&Learn pushbutton
048834 IP55 passive IR (PIR) movement sensor, suitable
for the detection of movement in outdoor or
indoor transit areas (corridors, cellars, garage
paths). Coverage area: 140° x 15m at 2.5m high.
Operating mode (automatic or manual), time
delay (5 s to 59min), and brightness threshold
(20 to 1275 LUX) settable using the advanced/
basic (BMSO4001/BMSO4003) configuration
remote control; physical or virtual configuration.
Wall or angular installation by means of
accessory item 048971

FEATURES OF THE LIGHTING/MOVEMENT SENSORS

SCS SENSORS 048834 BMSE3001 BMSE3003
INSTALLATION wall mounted ceiling flush mounted
TYPE OF OPERATION AUTO/ECO/WALKTHROUGH AUTO/ECO/WALKTHROUGH
SENSOR TECHNOLOGY PIR PIR PIR+US
POWER SUPPLY 27 V d.c. from Bus 27 V d.c. from Bus
PROTECTION INDEX IP55 IP20
COVERAGE AREA AT 2.5 m 15 m x 6 m Ø8m Ø 11 m
COVERAGE ANGLES (v/h) 45°/140° 90/360°
LIGHTING LEVEL 5 lux - 1275 lux 5 lux - 1275 lux
SWITCHING OFF DELAY 5 s 59 min 59 h 30 s - 255 h 59 min 59 sec
FACTORY ADJUSTMENTS 300 lux - 15 min 300 lux - 15 min
CONNECTION TYPE SCS clamp RJ45 connector

116
NOTE: White device Tech device Anthracite device Neutral item
TEMPERATURE CONTROL

KG4691 H4691 HS4693 N4693 3454

Item PROBE WITH DISPLAY Item PROBE WITHOUT DISPLAY

flush mounted device with backlit display. It 3454 temperature probe in basic module with wired
can be used to control the temperature of an sensor - to be associated to the temperature sensor
individual zone, irrespective of a temperature item 3457 and Vantage probe item 8051
control central unit being installed as part of
the system or not. It has a temperature probe ACCESSORIES
and an input for the connection of a contact 3457 temperature probe to be associated to the probe item
3454
line (e.g. window contact). It can be used for
the management of different types of systems,
and the adjustment of the fan speed when fan ACTUATORS
coils are used. Possibility of automatic operation F430/2 actuator with 2 independent relays – for single
(summer/winter) with compatible systems. bus and double loads: 6 A resistive, 2A motor driven
SCS connection – 2 modules. valves and pumps - configuration based logic
H4691 Axolute relay interlock - 2 DIN modules
Livinglight F430/4 actuator with 4 independent relays - for single,
LN4691
double or mixed loads: 4 A resistive, 1 A motor
driven valves, pumps and fan coils - configuration
KW4691 Living Now
based logic relay interlock - 2 DIN modules
KG4691
actuator with 8 independent relays for the
SET

KM4691 F430R8
control of on-off valves, motorised valves (open-
close and three points), pumps and fan coils with
SLAVE PROBE 2 and 4 tubes - 4A resistive, 1A motor valves,
probe to control the room temperature for pumps and fan-coils- SCS-bus connection - 4 DIN
heating and cooling systems – temperature modules
measurement range 3–40 °C F430R3V10 actuator with 3 independent relays and 2 x 0-10
- 2 modules Volts outputs for the control of fan coils with 2
HD4693 Axolute and 4 tubes with proportional 0-10 Volt valves -
HC4693 4A resistive, 1A fan coil - SCS-BUS connection - 4
HS4693 DIN modules
N4693 Livinglight F430V10 actuator with 2 x 0-10 Volt outputs for the control
NT4693 of 0-10 proportional valves - SCS-BUS connection
L4693 - 2 DIN modules

NOTE: White device Tech device Anthracite device Neutral item sand device

Catalogue MyHOME_Up 117

 ENERGY MANAGEMENT

3523 F521 F522 F523 N4672N 3508BUS MHKIT4015

Item CONSUMPTION DISPLAY Item LOAD CONTROL MANAGEMENT

F520 meter for the measurement of electricity on a 1 relay actuator - 10 A for incandescence lamps
maximum of 3 lines, by connecting 3 toroids to the and 4 A for fluorescent lamps or ferromagnetic
appropriate inputs. Version for fastening on DIN transformers, and 500 W for compact fluorescent
rail - 1 module. and LED lamps for the Automation and/or Load
The device is fitted with 1 toroid. control management functions. Pushbutton for
3523 Additional electricity meter toroid, item F520 forced load operation - flush mounted version - 2
and for actuator with sensor, item F522 for the modules
measurement of the earth leakage current. Cable HD4672N Axolute
length 400 mm. HC4672N
HS4672N
LOAD CONTROL MANAGEMENT N4672N Livinglight
F521 central unit for the management and control NT4672N
of the actuators of the load control system, to L4672N
prevent the risk of detachment of the limiter of
the electricity supplier. The central unit manages ACCESSORIES
up to 63 loads, a contract power between 1.5 and 3508BUS removable clamp for BUS connection
18 kW, and tolerance up to +/- 20%. It integrates - width 3.81 mm
an electricity meter for the controlled line. 3508U2 removable clamp 2 poles
Version for fastening on DIN rail - 1 module. The 3508U3 removable clamp 3 poles
device is fitted with 1 toroid.
F522 actuator with integrated current sensor LOAD CONTROL KIT
for the measurement of the controlled MHKIT4015 This kit gives the possibility of managing the
load consumptions. 1 relay - 10 A for maximum power used and automatically
incandescence lamps and 4 A for fluorescent disconnect the less important users in case of
lamps or ferromagnetic transformers, and overload (based on set priority levels). It can easily
500 for compact fluorescent and LED lamps - be expanded and integrated with other MyHOME
Bistable relay with zero crossing for the Automation functions. The kit includes:
and/or Load control management functions. • 1 power supply item E49
Version for fastening on DIN rail - 1 module. Earth • 1 load control central unit item F521
leakage control by connecting the additional • 1 x 16A actuator with measurement sensor item
toroid, item 3523. F522
F523 1 relay actuator - for incandescence lamps and • 2 actuators item F523
4 A for fluorescent lamps or ferromagnetic • 1 energy display item LN4710
transformers, and 500 W for compact fluorescent • various configurators.
and LED lamps - bistable relay with zero
crossing for the Automation and/or Load control
management functions. Version for fastening on
DIN rail - 1 module.

118
NOTE: White device Tech device Anthracite device Neutral item
COMMON ACCESSORIES AND DEVICES

E46ADCN E49 3545 L4669 336904

L4669/500

Item POWER SUPPLIES Item GUARANTEE EXTENSION VOUCHERS

E46ADCN power supply - input 230 Va.c. output 27 Vd.c. MHBASIC5A voucher for the guarantee extension for up
5 years
SELV - maximum absorbed current 450mA - to 5 years for Light and Automation, Energy
installation on DIN profile for flush mounted or management, Sound and NUVO, Video door entry
wall-mounted switchboards - 8 DIN modules and Remote control systems
E49 compact power supply - input 230 Va.c. - MHPLUS5A voucher for the guarantee extension as above,
output 27 Vd.c. Maximum current delivered but also valid for Temperature control and
600 mA - 2 DIN modules. Burglar alarm systems, and MyHome_screen 3.5
touch screen devices
VARIOUS ACCESSORIES voucher for the guarantee extension as above,
MHFULL5A
3515 spare removable clamp but also valid for MyHome_screen 10 touch
screen devices
CONNECTION CABLES
TECHNICAL SUPPORT VOUCHER sheathed pair made up of 2 flexible wires with
L4669
3545 set of 5 vouchers for the intervention of a unshielded plaited sheath - insulation 300/500 V
Technical Support technician for MyHOME, Video - complies with standards CEI 46-5 and CEI 20-20
door entry, Telephone, Luminous notification and - coil length 100 metres
CCTV systems as above - in 500 m coils
L4669/500
L4669KM1 as above - reel lenght 1000 m (1)

336905 as above - low toxicity cable without halogens -

ideal for application in environments where fire
hazard safety is critical - coil length 200 metres
336904 specific cable with 2 twisted conductors. It can be
installed in underground piping, in accordance
with standards (CEI 20-13 and CEI 20-14). It
ensures the best performance in video systems
(higher distance between EP and Handset when
compared with other cables). 200 m coil

System Cable
L4669 336904
L4669/500
L4669KM1
336905
Automation • • (1)
Energy Management/Consumption Display • • (1)
Temperature control • • (1)
Video door entry system •
NOTE (1): for systems underground cable sections

Catalogue MyHOME_Up 119

NOTE: White device Tech device Anthracite device Neutral item
 LIVING NOW KEY COVERS

COVER FOR ACTUATOR ITEM K4672M2L, COVER FOR ACTUATOR ITEM K4672M2S,
CONTROLS ITEM K4652M2 AND ITEM K4652M3 CONTROLS ITEM K4652M2 AND ITEM K4652M3

KW01 KG01MHAG KM19MH KW01A KG01MHGEN KW05 KG06MH

KM01MHBACK KW01MHBED KG01D KM01F KW01X

LIGHTABLE COVERS - 1 FUNCTION LIGHTABLE COVERS - 1 FUNCTION

1 module 1 module
Description Item Description Item
KW01 KW05
NEUTRAL KG01 SHUTTERS UP/DOWN KG05
KM01 KM05
KW01MHAG KW06MH
ON/OFF KG01MHAG SHUTTERS STOP KG06MH
KM01MHAG KM06MH
KW19MH
+/- FOR DIMMER KG19MH
KM19MH
KW01A
LIGHT/WAKE UP KG01A
KM01A
KW01MHGEN
OUTPUT KG01MHGEN
KM01MHGEN
KW01MHBACK
COMING IN KG01MHBACK
KM01MHBACK
KW01MHBED
BED KG01MHBED
KM01MHBED
KW01D
DOORBELL KG01D
KM01D
KW01F
KEY KG01F
KM01F
KW01X
HIGH BRIGHTNESS KG01X
KM01X

120
NOTE: White device sand device black device
LIVING NOW KEY COVERS

COVERS FOR ACTUATOR ITEM K4672M2L AND COVERS FOR ACTUATOR ITEM K4672M2S AND
CONTROL ITEM K4652M2 CONTROLS ITEM K4652M2

KW01MH2 KG01MH2AG KM19MH2 KW01MH2A KG05MH2

LIGHTABLE COVERS - 1 FUNCTION

2 modules
Description Item
KW05MH2
UP/DOWN KG05MH2
KM05MH2
KG01MH2GEN KM01MH2BACK KW01MH2BED KG01MH2D

COVERS FOR GREEN SWITCH ITEM K4659

KM01MH2F KW01MH2X

LIGHTABLE COVERS - 1 FUNCTION

2 modules 2 modules
Description Item Item
KW01MH2 KW17
NEUTRAL KG01MH2 KG17
KM01MH2 KM17
KW01MH2AG
ON/OFF KG01MH2AG
KM01MH2AG
KW19MH2 COVERS FOR BURGLAR-ALARM ACTIVATOR ITEM K4215
+/- FOR DIMMER KG19MH2
KM19MH2
KW01MH2A
LIGHT/WAKE UP KG01MH2A
KM01MH2A
KW01MH2GEN
OUTPUT KG01MH2GEN
KM01MH2GEN 1 module
KW01MH2BACK Item
COMING IN KG01MH2BACK KW24
KM01MH2BACK KG24
KW01MH2BED KM24
BED KG01MH2BED
KM01MH2BED
KW01MH2D
DOORBELL KG01MH2D
KM01MH2D
KW01MH2F
KEY KG01MH2F
KM01MH2F
KW01MH2X
HIGH BRIGHTNESS KG01MH2
KM01MH2X

Catalogue MyHOME_Up 121

NOTE: White device sand device black device
 OTHER KEY COVERS

2-FUNCTION NON-SILK-SCREEN PRINTED KEY COVERS 2-FUNCTION NON-SILK-SCREEN PRINTED KEY COVERS

Axolute Livinglight Màtix Axolute Livinglight Màtix

HD4915 HD4915M2 N4915LN N4915M2LN AM5911* HD4911 HD4911M2 N4911N N4911M2N AM5911/2*

HC4915 HC4915/2 NT4915N NT4915N HC4911 HC4911M2 NT4911N NT4911M2N

HS4915 HS4915/2 L4915N L4915N HS4911 HS4911M2 L4911N L4911M2N

NON-SILK-SCREEN PRINTED KEY COVERS - 1 FUNCTION NON-SILK-SCREEN PRINTED KEY COVERS - 2 FUNCTIONS
1 module 2 modules 1 module 2 modules
Item Item Item Item
Axolute Axolute
HD4915 HD4915M2 HD4911 HD4911M2
HC4915 HC4915/2 HC4911 HC4911/2
HS4915 HS4915/2 HS4911 HS4911/2
Livinglight Livinglight
N4915LN N4915M2LN N4911N N4911M2N
NT4915N NT4915M2N NT4911N NT4911M2N
L4915N L4915M2N L4911N L4911M2N
Màtix Màtix
AM5911* AM5911/2* AM5911* AM5911/2*

* key cover that can be used for 1 and 2 functions NOTE: the control keys are supplied with
the device.

upper pushbutton

control
lower pushbutton key
LED

key cover
2 functions
2 modules
key cover
1 function
key cover 2 modules
key cover 2 functions
1 function 1 module
1 module

122
NOTE: White device Tech device Anthracite device Neutral item
1-FUNCTION SILK-SCREEN PRINTED KEY COVERS

Axolute Livinglight Màtix

HD4915AA HC4915/2AA HS4915BA NT4915AN NT4915M2ADN NT4915MR AM5915AC AM5915/2AA AM5915BA

SILK-SCREEN PRINTED KEY COVERS WITH SYMBOLS - 1 FUNCTION

Axolute Livinglight Màtix
1 module 2 modules 1 module 2 modules 1 module 2 modules
Description Item Item Item Item Item Item
HD4915AA HD4915M2AA — —
OFF HC4915AA HC4915/2AA — — AM5915AA AM5915/2AA
HS4915AA HS4915/2AA — —
HD4915AB HD4915M2AB — —
ON HC4915AB HC4915/2AB — — AM5915AB AM5915/2AB
HS4915AB HS4915/2AB — —
HD4915AC HD4915M2AC — —
GEN HC4915AC HC4915/2AC — — AM5915AC AM5915/2AC
HS4915AC HS4915/2AC — —
HD4915AD HD4915M2AD — N4915M2ADN
DIMMER HC4915AD HC4915/2AD — NT4915M2ADN AM5915AD AM5915/2AD
HS4915AD HS4915/2AD — L4915M2ADN
HD4915AE — N4915AEN —
STOP HC4915AE — NT4915AEN — AM5915AE —
HS4915AE — L4915AEN —
HD4915BA HD4915M2BA N4915AN N4915M2AN
LIGHT HC4915BA HC4915/2BA NT4915AN NT4915M2AN AM5915BA AM5915/2BA
HS4915BA HS4915/2BA L4915AN L4915M2AN
— — N4915BN N4915M2BN — —
STAIRCASE LIGHT — — NT4915BN NT4915M2BN — —
— — L4915BN L4915M2BN — —
HD4915BL HD4915M2BL — — — —
BED LIGHT HC4915BL HC4915M2BL — — — —
HS4915BL HS4915M2BL — — — —
HD4915BB HD4915M2BB — —
BELL HC4915BB HC4915/2BB — — AM5915BB —
HS4915BB HS4915/2BB — —
HD4915BC HD4915M2BC — —
EXHAUST FAN HC4915BC HC4915/2BC — — — —
HS4915BC HS4915/2BC
HD4915BD N4915FN N4915M2FN
KEY HC4915BD NT4915FN NT4915M2FN AM5915BD —
HS4915BD L4915FN L4915M2FN
HD4915DD HD4915M2DD N4915DD N4915M2DD — —
DO NOT DISTURB HC4915DD HC4915M2DD NT4915DD NT4915M2DD — —
HS4915DD HS4915M2DD L4915DD L4915M2DD — —
— — N4915DN N4915M2DN — —
DOORBELL — — NT4915DN NT4915M2DN — —
— — L4915DN L4915M2DN — —
HD4915MR — N4915MR — — —
MAKE UP THE ROOM HC4915MR — NT4915MR — — —
HS4915MR — L4915MR — — —

Catalogue MyHOME_Up 123

NOTE: White device Tech device Anthracite device Neutral item
 OTHER KEY COVERS
2-FUNCTION SILK-SCREEN PRINTED KEY COVERS

Axolute Livinglight Màtix

HD4911AF HD4911MAF HC4911BC NT4911AHN NT4911AIN AM5911AF AM5911AI

SILK-SCREEN PRINTED KEY COVERS WITH SYMBOLS - 2 FUNCTIONS

Axolute Livinglight Màtix
1 module 2 modules 1 module 2 modules 1 module 2 modules
Description Item Item Item Item Item Item
HD4911AF HD4911M2AF N4911AFN N4911M2AFN
ON - OFF - GEN HC4911AF HC4911/2AF NT4911AFN NT4911M2AFN AM5911AF (*) AM5911/2AF
HS4911AF HS4911/2AF L4911AFN L4911M2AFN
HD4911AG HD4911M2AG N4911AGN N4911M2AGN
ON - OFF HC4911AG HC4911/2AG NT4911AGN NT4911M2AGN AM5911AG AM5911/2AG
HS4911AG HS4911/2AG L4911AGN L4911M2AGN
HD4911AH HD4911M2AH N4911AHN N4911M2AHN
UP - DOWN HC4911AH HC4911/2AH NT4911AHN NT4911M2AHN AM5911AH AM5911/2AH
HS4911AH HS4911/2AH L4911AHN L4911M2AHN
HD4911AI HD4911M2AI N4911AIN N4911M2AIN
ON - OFF
HC4911AI HC4911/2AI NT4911AIN NT4911M2AIN AM5911AI (*) AM5911/2AI
ADJUSTMENT
HS4911AI HS4911/2AI L4911AIN L4911M2AIN
HD4911BA HD4911M2BA — — — —
LIGHT HC4911BA HC4911/2BA — — — —
HS4911BA HS4911/2BA — — — —
HD4911BC HD4911M2BC — — — —
EXHAUST FAN HC4911BC HC4911/2BC — — — —
HS4911BC HS4911/2BC — — — —
HD4911BE — — — — —
TREBLE CLEF HC4911BE — — — — —
HS4911BE — — — — —
HD4911AD — N4911ADN — — —
+ up and
HC4911AD — NT4911ADN — — —
– down
HS4911AD — L4911ADN — — —

NOTE (*): key covers also suitable for use with Sound System devices

124
NOTE: White device Tech device Anthracite device Neutral item
CUSTOMISABLE LIVINGLIGHT KEY COVERS WITH DIFFUSERS, AVAILABLE IN KIT
CUSTOMISABLE KEY COVERS 1 FUNCTION 2 FUNCTIONS
1 module 2 modules
Description Item Item
1 FUNCTION CUSTOMISABLE N4915TN N4915M2TN
KEY COVER WITH 1 DIFFUSER* NT4915TN NT4915M2TN
L4915TN L4915M2TN
Customisable Customisable
2 FUNCTION CUSTOMISABLE N4911TN N4911M2TN with 1 diffuser with 2 diffusers
KEY COVER WITH 2 DIFFUSERS* NT4911TN NT4911M2TN
L4911TN L4911M2TN

DIFFUSER KIT
Description Item
KIT WITH DIFFUSER ON THE SIDE N4915SETBL
(50 DIFFUSERS)
NT4915SETBL
L4915SETBL

Catalogue MyHOME_Up 125

 MyHOME FLATWALL
BASE, DEVICE HOLDER SUPPORTS AND ACCESSORIES

Item BASIC MODULE FOR WALLS

3750 basic module h 240 - 270 cm, for masonry walls made up of:
lower module bottom, telescopic module bottom, upper end
cap, bracket with adjustable feet, cable fastener plate and
masonry net
3751 module as above, for plasterboard walls
3823 flush mounted module h 150 cm for masonry and plasterboard
walls

3750 3823
3751

Item DEVICE HOLDER SUPPORTS AND ACCESSORIES

3787 device holder support h 30 cm max 36 DIN mod.
3788 device holder support for free fastening of non-DIN devices or
for cable fastening in the riser solution
3787 3788 3789 device holder support h 60 cm max 72 DIN mod.
3801 mounting bracket for 1 or 2 MyHOME devices - 506E modu-
larity
3789 3802 mounting bracket for 3 MyHOME devices - 506E modularity
3805 pair of brackets for non-modular central units
3790 pair of kits with trunking and DIN rails for 3788
3756 horizontal partition (optional)
3803 extension module. To be used as a connector when passing
3801 3802 between floors. It is indispensable to use it in the riser solution
3804 vertical partition h 300 cm to separate the cables in the riser
solution
3828 multimedia box to be completed with appropriate clips F496/MF
3831 cable entry kit for multimedia box

3805 3790 3756

3803 3828 3804

126
MyHOME FLATWALL
FINISHES

Item PANELS
3794N front cover panel h 120 cm for 1 device with 506E modularity
3795N front cover panel h 120 cm for 2 devices with 506E modularity
3796N front cover panel h 120 cm for 3 devices with 506E modularity
3791N front cover panel h 30 cm for 1 device with 506E modularity
3792N front cover panel h 30 cm for 2 devices with 506E modularity
3793N front cover panel h 30 cm for 3 devices with 506E modularity
3797* DIN switchboard h 30 cm - glass
3798* DIN switchboard h 30 cm - metal sheet
3829 Multimedia box panel h 30 cm
3799* DIN switchboard h 30 cm - plastic
3757 front cover panel h 30 cm
3794N 3795N 3796N
3759 front cover panel h 60 cm
3785 front cover panel h 90 cm
3786 front cover panel h 120 cm
3771 upper and lower finishing end caps for 240 and 270 version
3825 upper and lower finishing end caps for 150 version
3791N 3792N 3793N 3761** front cover panel for non-modular central units
3769 front cover panel h 60 cm for burglar alarm
* Provide some white blanking modules F215FP, to close any internal
empty compartments
** Provide some white blanking modules 16133, to close any empty
compartments
3797 3798 3799
3829

3757

3759

3785
3825 3786

3771 3761

Item FRAMES AND PROFILES

3817N frame for AXOLUTE items
3818N frame for LIVING items
3821 side finishing profiles h 270 cm
3821 3822 side finishing profiles h 240 cm
3817N 3822 3826 side finishing profiles h 150 cm
3818N 3826

Catalogue MyHOME_Up 127

 ASSEMBLY GUIDE:
MyHOME FLATWALL 240 - 270 AS SWITCHBOARD

SUPPORTS FOR MyHOME

DEVICES WITH 506E
BASIC SETUP: DEVICE HOLDER SUPPORTS MODULARITY
BOTTOM AND ACCESSORIES

3802
Mounting bracket
3 devices

3787
Device holder support
h 30 cm max 36 DIN mod. 3801
Mounting bracket
1 or 2 devices

3756
Horizontal partition
(optional)

3789
Device holder support
h 60 cm max 72 DIN mod.
Power supplies and other devices
MyHOME DIN module

DIN protective devices

3788 3790
Device holder support for Pair of kits with
free fastening of non-DIN trunking and DIN rails
devices for 3788 (optional)

3828
Multimedia equipment box
F496/MF
Clips

3750
Flush mounted bottom

3751 3787
3805
Flush mounted bottom Device holder support
Support bracket 3550 3486
for plasterboard h 30 cm max 36 DIN mod.
for non-modular Temperature GSM burglar-alarm
(without masonry net) central units control central unit central unit

128
FINISHINGS: PANELS FOR DEVICES WITH 506E MODULARITY, END CAPS AND FRAMES*** SIDE FRAME
FINISHING

3817N
Frames for
AXOLUTE items

3794N 3795N 3796N

Front cover plate Front cover plate Front cover plate
h 120 cm for one device h 120 cm for two devices h 120 cm for three devices

3818N
Frames for
LIVING items

3791N 3792N 3793N

Front cover plate Front cover plate Front cover plate
as above h 30 cm as above h 30 cm as above h 30 cm

3797** 3798** 3799**

DIN switchboard DIN switchboard DIN switchboard
h 30 cm - glass h 30 cm - metal sheet h 30 cm - plastic

3829 3757 3759 3785 3786

Multimedia Front cover plate Front cover plate Front cover plate Front cover plate
box panel h 30 cm h 60 cm h 90 cm h 120 cm 3821
h 30 cm 3822
Side finishing frames
h 270 cm and
h 240 cm

* Provide some white blanking modules 16133, to close

any empty compartments
3771 ** Provide some white blanking modules F215FP to close
Upper and lower finishing end caps any internal empty compartments
(to be fitted last) *** Panels and end cap must always be installed after the
side finishing frames (3821 or 3822).
3761
Front cover panel for
non-modular central
units*
Catalogue MyHOME_Up 129
 ASSEMBLY GUIDE:
MyHOME FLATWALL 150 AS SWITCHBOARD
SUPPORTS FOR MyHOME
DEVICES
BASIC SETUP: DEVICE HOLDER SUPPORTS 506E MODULARITY
BOTTOM AND ACCESSORIES

3802
Mounting bracket
for 3 devices

3801
Mounting bracket
for 1 or 2 devices

3787
Device holder support
h 30 cm max 36 DIN mod.

3756
horizontal partition
(optional)

Power supplies and other MyHOME devices

3789 DIN module
Device holder support
h 60 cm max 72 DIN mod.

DIN protective devices

3823
Flush mounted bottom

3788 3790
Device holder support for Pair of kits with trunking
free fastening of non-DIN and DIN rails for 3788
devices (optional)

3828
Multimedia equipment box
F496/MF
Clips

3787 3550 3486

3805
Device holder support Temperature GSM burglar-alarm
Support bracket
h 30 cm max 36 DIN mod. control central unit central unit
for non-modular
central units

130
FINISHINGS: PANELS FOR DEVICES WITH 506E MODULARITY, END CAPS AND FRAMES*** SIDE FRAME
FINISHING

3791N 3792N 3793N

Front cover plate Front cover plate Front cover plate
h 30 cm for one device h 30 cm for two devices h 30 cm for three devices

3817N 3818N
Frames for Frames for
AXOLUTE items LIVING items

3797** 3798** 3799**

DIN switchboard DIN switchboard DIN switchboard
h 30 cm - glass h 30 cm - metal sheet h 30 cm - plastic

3829 3757 3759 3785

Multimedia Front cover plate Front cover plate Front cover plate 3826
box panel h 30 cm h 60 cm h 90 cm side finishing frames
h 30 cm h 150 cm

3825 * Provide some white blanking modules 16133, to close

Upper and lower finishing any empty compartments
end caps (to be fitted ** Provide some white blanking modules F215FP to close
before front cover panels) any internal empty compartments
*** Panels and end cap must always be installed after the
side finishing frames (3821 or 3822).
3761
Front cover panel for
non-modular central
units*
Catalogue MyHOME_Up 131
 ASSEMBLY GUIDE:
MYHOME FLATWALL 240 - 270 AS ELECTRIC PANEL

BASIC SETUP: DEVICE HOLDER SUPPORTS DEVICES FINISHINGS: PANELS, END SIDE FRAME
BOTTOM SUPPORTS AND FOR MYHOME THAT CAN BE CAPS AND FRAMES*** FINISHING
ACCESSORIES DEVICES INSTALLED

3759
3803 Front cover panel h 60 cm
Extension module
(indispensable use in
the riser solution)

3787
Device holder support
h 30 cm max 36 DIN mod.
3785
3756 Front cover panel h 90 cm
horizontal partition Power supplies
(optional) and other
MyHome devices -
DIN module

3789
Device holder support
h 60 cm max 72 DIN mod.

3786
Front cover panel h 120 cm

3821
3822
Side finishing
frames h 270 cm
3788 3790 and h 240 cm
Device holder support for free Pair of kits with trunking and DIN
fastening of non-DIN devices rails for 3778 (optional) 3771
3750 Upper and lower finishing
Flush mounted bottom end caps (to be fitted last)
3751
Flush mounted bottom *** Panels and end cap must
for plasterboard always be installed after the side
(without masonry net) finishing frames (3821 or 3822).

132
ASSEMBLY GUIDE:
MyHOME FLATWALL 150 AS ELECTRIC PANEL

BASIC SETUP: DEVICE HOLDER SUPPORTS DEVICES THAT CAN FINISHINGS: SIDE FRAME
BOTTOM SUPPORTS AND FOR MY HOME BE INSTALLED PANELS, END CAPS FINISHING
ACCESSORIES DEVICES AND FRAMES***

3787
Device holder support h
30 cm max 36 DIN mod.
3756
Horizontal partition Power supplies and 3759
(optional) other MyHome devices Front cover panel h 60 cm
- DIN module

3789
Device holder support h
60 cm max 72 DIN mod.

3785
Front cover panel h 90 cm

3823
Flush mounted bottom
3826
3825 side finishing
Upper and lower finishing frames h 150 cm
end caps (to be fitted before
3788 3790 front cover panels)
Device holder support for Pair of kits with trunking and DIN
*** Panels and end cap must
free fastening of non-DIN rails for 3778 (optional)
always be installed after the
devices
side finishing frames (3821
or 3822).

Catalogue MyHOME_Up 133

 ASSEMBLY GUIDE:
MyHOME FLATWALL 240 - 270 AS FLOOR RISER

BASIC SETUP: BRACKETS AND ACCESSORIES FINISHINGS: PANELS AND SIDE FRAME
BOTTOM END CAPS *** FINISHING

3759
Front cover plate
3803
h 60 cm
Extension module
(indispensable use in
the riser solution)

3788 3804 3786

Device holder support Vertical Front cover plate
for cable fastening partition 3785 h 120 cm
h 300 cm Front cover plate
h 90 cm

3790 *** Panels and end cap

Pair of kits with trunking must always be installed
and DIN rails for 3778 3771 after the side finishing
(optional) Upper and lower frames (3821 or 3822).
finishing end caps (to be
fitted last)

3821
3822
Side finishing frames
h 270 cm
and h 240 cm

3750
Flush mounted bottom
Floor
slab Extension
3751
module
Flush mounted bottom
for plasterboard
(without masonry net) 3803
Example of installation of the extension module

134
COMPOSITION EXAMPLE
Composition with switchboard for protective devices h 270 cm.

Bottom modularity View of the completed product

Item LIST OF THE MATERIAL Quantity

3750 Flush mounted bottom 1
3789 Device holder support h 60 cm 4
3786 Front cover panel h 120 cm 1
3785 Front cover panel h 90 cm 1
3797 DIN switchboard h 30 cm - glass 1
3821 Pair of side frames h 270 cm 1
3771 Upper and lower finishing end caps 1

Composition with switchboard for protective devices h 240 cm.

Bottom modularity View of the completed product

Item LIST OF THE MATERIAL Quantity

3750 Flush mounted bottom 1
3789 Device holder support h 60 cm 3
3787 Device holder support h 30 cm 1
3785 Front cover panel h 90 cm 2
3797 DIN switchboard h 30 cm - metal sheet 1
3822 Pair of side frames h 240 cm 1
3771 Upper and lower finishing end caps 1

Catalogue MyHOME_Up 135

 MyHOME FLATWALL - DIMENSIONAL DATA

MyHOME FLATWALL 240 - 270

63 cm

56 cm 58 cm
63 cm

56 cm 58 cm
267.5 cm

267.5 cm

237.5 cm
237.5 cm
165 cm
3 cm*

3 cm*

* Bottom part embedded in the floor only corresponding to the 3750 (not for 3751).

Thickness - top view with assembled components

8.5 cm

58 cm
Maximum protrusion from the wall: 2 cm

MyHOME FLATWALL 150

56 cm 58 cm

Thickness - top view with assembled components

8.5 cm
154.1 cm

58 cm
153 cm

Maximum protrusion from the wall: 2 cm

100 cm

60 cm

136
PANELS, SWITCHBOARDS, FINISHING END CAPS AND EXTENSION MODULE (PASSING BETWEEN FLOORS)

53.3 cm 53.3 cm 53.3 cm

7 cm
30 cm

30 cm
14.5 cm 14.5 cm 14.5 cm

3791, 3792, 3793 3797, 3798, 3799 45 cm

53.3 cm 53.3 cm

120 cm
30 cm

30 cm

54.5 cm
3757 3761

53.3 cm 53.3 cm

3794, 3795, 3796 3803

53.3 cm 53.3 cm
30 cm

60 cm

3829

3759 90 cm

120 cm
58 cm 4 cm ± 1 cm
adjustable

25 cm ± 1 cm
2 cm

3825 adjustable
3785
53.3 cm
3771
3786
DEVICE HOLDER SUPPORTS
Max 72 DIN modules divided on 4 rows of 18 - Max 36 DIN modules divided on 2 rows of 18.
54 cm

54 cm
59 cm

38 cm
29 cm

12 cm

3789 3787 3801 - 3802

37.8 cm 32 cm 7 cm
25 cm
15 cm

30 cm

23.5 cm
29 cm

18 cm 3828
3788
Useful space for installing multimedia devices
28 cm

Catalogue MyHOME_Up 137

 APPENDIX

Devices which can be associated with the MyHOME_Up app

and MyHOMEServer1 gateway
The following pages provides the list of devices of the light and shutter Automation system and
Temperature control system which are associated using MyHOMEServer1 devices and MyHOME_
APP. The Energy Management actuators are configured using MyHome_Suite software.

LIGHT AND AUTOMATION DEVICES THAT CAN BE ASSOCIATED

BTicino From production Channels configured automatically
Description
Code batch: by MyHOMEServer1
L4680 09W08
N4680 09W08
NT4680 09W08
Scenario control
HC4680 09W08
HD4680 09W08
HS4680 09W08
SCS/SCS interface F422 12W20
LN4652 all
BUS 8-key control
H4652 all
K4652M2 all
H4652/2 09W40
2 m basic control
L4652/2 09W40
AM5832/22 09W40
K4652M3 all
L4652/3 09W40
3 m basic control
H4652/3 09W40
AM5832/3 09W40
Light actuator K8002L all
LN4661M2 all 1
H4661M2 all 1
BUS shutter actuator
AM5861M2 all 1
K8002S all
LN4660M2 all
BUS shutter control H4660M2 all
AM5860M2 all
L4651M2 08W41
Special control H4651M2 08W41
AM5831M2 08W41
16A 100/240V 1 relay DIN actuator F411U1 all 1
16A 100/240V 2 relay DIN actuator F411U2 all 2
16A 100/240V 1 relay DIN actuator F411/1N 09W13 1
16A 2 relay DIN actuator F411/2 09W04** 2
16A 100/240V 2 relay DIN actuator BMSW1002 all 2
16A 100/240V 4 relay DIN actuator BMSW1003 all 4
6A 4 relay DIN actuator F411/4 09W04* 4
16A 100/240V 4 relay DIN actuator BMSW1005 all 8
4 output DIN actuator for 0-10V ballast BMDI1002 all 4
DIN actuator for 0-10V ballast F413N 09W14 1
Basic contact interface 3477 10W04
DIN contact interface F428 09W50

* If the device is installed on the output of the F422 interface, the minimum batch is 15W25
** If the device is installed on the output of the F422 interface, it is not possible to associate it using the APP.
It is recommended to replace it with the code F411U2

138
For the updated list of devices see the technical sheet of the gateway device item
MyHOMEServer1.

BTicino From production Channels configured automatically

Description
Code batch: by MyHOMEServer1
1000 VA DIN dimmer F416U1 all 1
1000 W DIN dimmer F414 09W29 1
400 VA DIN dimmer F415 09W22 1
2 x 400 VA DIN dimmer F417U2 all 2
300 VA DIN dimmer F418 all 1
2 x 300 VA DIN dimmer F418U2 all 2
HC4657M3 11W09
3 m touch control HD4657M3 11W12
HS4657M3 11W12
HC4657M4 11W12
4 m touch control HD4657M4 11W12
HS4657M4 11W14
SCS/DALI interface F429 10W20 8
Basic actuator 3475 12W31 1
BUS shutter DIN actuator F401 all 1
K4672M2L all
2
AM5852M2 all
Control actuator 2
H4672M2 all
2
LN4672M2 all
Basic control actuator 3476 12W39 1
K4672M2S all
Control actuator 2
LN4671M2 all
DIN dimmer for 0-10 V ballast BMDI1001 all 1
L4658N all
N4658N all
NT4658N all
BUS Dual Tech Green Switch
HC4658 all
HD4658 all
HS4658 all
K4659 all
L4659N all
N4659N all
NT4659N all
PIR BUS automatic switch
HC4659 all
HD4659 all
HS4659 all
PIR ceiling mounted sensor BMSE3001 all
PIR+US double technology ceiling
BMSE3003 all
mounted sensor
IP55 PIR wall mounted sensor
Memory module F425 10W01
K4652M2 all
Control
K4652M3 all

Catalogue MyHOME_Up 139

 APPENDIX

Devices which can be associated with the MyHOME_Up app

and MyHOMEServer1 gateway
TEMPERATURE CONTROL DEVICES

Description BTicino code From production batch:

Probe with Display LN4691 all

H4691 all
KM4691
KG4691
KW4691
Probe without display 3454 all
SLAVE probe L4693 13W36
N4693 13W36
NT4693 13W36
HC4693 13W36
HS4693 13W36
HD4693 13W36

DIN actuator with 2 independent relays F430/2 13W06

DIN actuator with 4 independent relays F430/4 13W06

DIN actuator with 8 independent relays F430R8 all

DIN actuator with 2 0-10 V outputs F430V10 all

DIN actuator with 3 independent relays F430R3V10 all

and 2 0-10 V outputs

NOTE 1: in the case of systems with 99-zone temperature control unit, the device configuration must be made by means of physical or virtual
configuration. In this case, all the batches are compatible.

NOTA 2: for any updates of this table, see the Gateway MyHOMEServer1 technical sheet in the Catalogue section of the bticino.com site

140
MyHOME_Up

HOME AUTOMATION
EVOLUTION
 BTicino SpA
Viale Borri, 231

www.bticino.com
21100 Varese - Italy

BTicino SpA reserves at any time the right to modify the contents of this booklet
AD-ITMH20GT/GB - Version 01/2020
and to communicate, in any form and modality, the changes brought to the same.

MyHOME_Up Technical guide 2020

VOICE
COMMAND
SMARTPHONE
CONTROL WITH
MANUAL
CONTROL
TOUCH
CONTROL
HOME AUTOMATION EVOLUTION
MyHOME_Up

AND CATALOGUE
FOR INSTALLATION
GUIDE