ILLUMINATION

LUXEON M
Brightest, most uniform and highest
efficacy multi-die emitter
LUXEON M is an illumination grade multi-die LED designed to enable

outdoor and industrial applications targeting either high efficiency or low

cost. With Freedom from Binning and leading performance, LUXEON M

falls within a single 3- or 5-step MacAdam ellipse centered in ANSI to

ensure color consistency from LED to LED, delivering high efficacy and

high flux density from a uniform source with tight correlated color

temperature control. The superior quality of light, volume of lumens,

and real world efficacy enable leading performance and efficient solution

development in a wide variety of lighting segments.

FEATURES AND BENEFITS PRIMARY APPLICATIONS

Uniform image enables tight beam control in MR16 and spotlight applications Architectural
High flux density from a 3mm area enables reduced emitter count and
2

compact fixture designs High Bay & Low Bay

11.2V, 5.6V and 2.8V package options puts high performance within reach
with high efficiency and low cost drivers Lamps
Leading thermal resistance allows flexible system design to optimize for
Outdoor
lm/$ and lm/W
Exceeds ENERGY STAR® lumen maintenance requirements Specialty Lighting

Spotlights

No. E352519
DS103 LUXEON M Product Datasheet ©2015 Lumileds Holding B.V. All rights reserved.
Table of Contents

General Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Product Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Lumen Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Optical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical and Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Characteristic Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Spectral Power Distribution Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Light Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Forward Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Radiation Pattern Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Product Bin and Labeling Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Decoding Product Bin Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Luminous Flux Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Radiometric Power Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Color Bin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dominant Wavelength Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Forward Voltage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Reflow Soldering Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
JEDEC Moisture Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Solder Pad Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Pocket Tape Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. i
General Product Information

Product Test Conditions

LUXEON M LEDs are tested and binned with a DC drive current of 700mA for LUXEON M 12V, 1400mA for LUXEON M 6V and
2800mA for LUXEON M 3V at a junction temperature, Tj, of 85ºC.

Part Number Nomenclature

Part numbers for LUXEON M follow the convention below:

L X R A – B C D D – E E E E

Where:

A – designates minimum CRI (7=70, 8=80, 9=90, 0=Royal Blue)

B – designates voltage (S=12V, R=6V, Q=3V)

C – designates color (W=White, R=Royal Blue)

D D – designates CCT (27=2700K, 30=3000K, 35=3500K, 40=4000K, 50=5000K, 57=5700K, 65=6500K, 00=Royal Blue)

E E E E – designates minimum luminous flux (optional)

Therefore, the following part number is used for a white LUXEON M 12V 3000K 80CRI:

L X R 8 – S W 3 0 – x x x x

Lumen Maintenance
Please contact your local Sales Representative or Lumileds Technical Solutions Manager for more information about the long-
term performance of this product.

Environmental Compliance
Lumileds LLC is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON M is
compliant to the European Union directives on the restriction of hazardous substances in electronic equipment, namely the
RoHS Directive 2011/65/EU and REACH Regulation (EC) 1907/2006. Lumileds LLC will not intentionally add the following restricted
materials to its products: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated
diphenyl ethers (PBDE).

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 2
Performance Characteristics

Product Selection Guide

Table 1a. Product performance for LUXEON M White at test current, Tj=85°C.

MINIMUM LUMINOUS FLUX [1] (lm) TEST CURRENT

VOLTAGE NOMINAL CCT [2] PART NUMBER
CRI (mA)
MINIMUM TYPICAL
3000K 70 900 1000 700 LXR7-SW30
4000K 70 970 1076 700 LXR7-SW40
5000K 70 1040 1100 700 LXR7-SW50
5700K 70 1040 1110 700 LXR7-SW57
6500K 70 1040 1130 700 LXR7-SW65
2700K 80 730 800 700 LXR8-SW27
12V 3000K 80 780 850 700 LXR8-SW30
3500K 80 780 870 700 LXR8-SW35
4000K 80 840 905 700 LXR8-SW40
5000K 80 840 920 700 LXR8-SW50
2700K 90 600 660 700 LXR9-SW27
3000K 90 640 736 700 LXR9-SW30
5700K 90 800 880 700 LXR9-SW57
3000K 70 900 1000 1400 LXR7-RW30
4000K 70 970 1076 1400 LXR7-RW40
5000K 70 1040 1100 1400 LXR7-RW50
5700K 70 1040 1110 1400 LXR7-RW57
6500K 70 1040 1130 1400 LXR7-RW65
2700K 80 730 800 1400 LXR8-RW27
6V 3000K 80 780 850 1400 LXR8-RW30
3500K 80 780 870 1400 LXR8-RW35
4000K 80 840 920 1400 LXR8-RW40
5000K 80 840 920 1400 LXR8-RW50
2700K 90 600 660 1400 LXR9-RW27
3000K 90 640 736 1400 LXR9-RW30
5700K 90 800 880 1400 LXR9-RW57
3000K 70 900 1000 2800 LXR7-QW30
4000K 70 970 1076 2800 LXR7-QW40
5000K 70 1040 1100 2800 LXR7-QW50
5700K 70 1040 1110 2800 LXR7-QW57
6500K 70 1040 1130 2800 LXR7-QW65
2700K 80 730 800 2800 LXR8-QW27
3V 3000K 80 780 850 2800 LXR8-QW30
3500K 80 780 870 2800 LXR8-QW35
4000K 80 840 920 2800 LXR8-QW40
5000K 80 840 920 2800 LXR8-QW50
2700K 90 600 660 2800 LXR9-QW27
3000K 90 640 736 2800 LXR9-QW30
5700K 90 800 880 2800 LXR9-QW57
Notes for Table 1a:
1. Lumileds maintains a tolerance of ±2 on CRI and ±6.5% on luminous flux measurements.
2. Typical CRI is approximately 2 points higher than the minimum CRI specified, but this is not guaranteed.

Table 1b. Product performance for LUXEON M Royal Blue at test current, Tj=85°C.

DOMINANT WAVELENGTH (nm) RADIOMETRIC POWER (mW) TEST CURRENT

VOLTAGE PART NUMBER
(mA)
MINIMUM MAXIMUM MINIMUM TYPICAL
12V 445 460 4200 4500 700 LXR0-SR00
6V 445 460 4200 4500 1400 LXR0-RR00
3V 445 460 4200 4500 2800 LXR0-QR00
Notes for Table 1b:
1. Lumileds maintains a tolerance of ±6.5% on radiometric power measurements.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 3
Optical Characteristics
Table 2. Optical characteristics for LUXEON M at test current, Tj=85°C.

PART NUMBER TYPICAL TOTAL INCLUDED ANGLE [1] TYPICAL VIEWING ANGLE [2]

LXRx-xxxx 140° 120°

Notes for Table 2:
1. Total angle at which 90% of total luminous flux is captured.
2. Viewing angle is the off axis angle from the LED centerline where the luminous intensity is ½ of the peak value.

Electrical and Thermal Characteristics

Table 3. Electrical and thermal characteristics for LUXEON M at test current, Tj=85ºC.

FORWARD VOLTAGE (V) [1] TYPICAL TEMPERATURE TYPICAL THERMAL

PART NUMBER COEFFICIENT OF FORWARD RESISTANCE — JUNCTION
MINIMUM TYPICAL MAXIMUM VOLTAGE (mV/°C) [2] TO SOLDER PAD (°C/W)

LXRx-Sxxx 10.50 11.20 11.70 -5.50 1.25

LXRx-Rxxx 5.25 5.60 6.00 -2.75 1.25
LXRx-Qxxx 2.63 2.80 3.00 -1.38 1.25
Notes for Table 3:
1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.
2. Measured between 25°C and 135°C.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 4
Absolute Maximum Ratings

Table 4. Absolute maximum ratings for LUXEON M.

PARAMETER MAXIMUM PERFORMANCE

1200mA for LXRx-SWxx

DC Forward Current at Tj=110°C [1][2] 2400mA for LXRx-RWxx
4800mA for LXRx-QWxx
1050mA for LXRx-Sxxx
DC Forward Current at Tj=135°C [1][2] 2100mA for LXRx-Rxxx
4200mA for LXRx-Qxxx
1375mA for LXRx-SWxx
2750mA for LXRx-RWxx
5500mA for LXRx-QWxx
Peak Pulsed Forward Current [3]
1200mA for LXR0-SR00
2400mA for LXR0-RR00
4800mA for LXR0-QR00

LED Junction Temperature (DC & Pulse) -40°C to 135°C

ESD Sensitivity (ANSI/ESDA/JEDEC JS-001-2012) Class 3B
Operating Case Temperature [1]
120°C
Storage Temperature -40°C to120°C

Soldering Temperature JEDEC 020c 260°C

Allowable Reflow Cycles 3

Reverse Voltage (Vreverse) LUXEON LEDs are not designed to be driven in reverse bias
Notes for 4:
1. See Figure 1 for more details on the maximum permissible operating conditions for LUXEON M White.
2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple”, are acceptable if the following conditions are met:
– The frequency of the ripple current is 100Hz or higher
– The average current for each cycle does not exceed the maximum allowable DC forward current at this junction temperature
– The maximum amplitude of the ripple does not exceed 15% of the maximum allowable DC forward current at this junction temperature
3. At 10% duty cycle with pulse width of 10ms.

Operating Conditions

Drive Current

If2

If1 [mA] If2 [mA]

LUXEON M White 3V 4200 4800

LUXEON M White 6V 2100 2400

If1
LUXEON M White 12V 1050 1200

Junction
0 Temperature [°C]
-40 110 135

Figure 1: Maximum permissible operating conditions for LUXEON M White.

Notes for Figure 1:

1. The green shaded area in this graph reflects the maximum permissible operating conditions for LUXEON M White.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 5
Characteristic Curves

Spectral Power Distribution Characteristics

LXR7-xW30
LXR7-xW40
LXR7-xW50
LXR7-xW57
LXR7-xW65

Figure 2a: Typical normalized power vs. wavelength for LXR7-xWxx at test current, Tj=85ºC.

x
x
x
x
x

Figure 2b: Typical normalized power vs. wavelength for LXR8-xWxx at test current, Tj=85ºC.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 6
 x
x

Figure 2c: Typical normalized power vs. wavelength for LXR9-xWxx at test current, Tj=85ºC.

Figure 2d: Typical normalized power vs. wavelength for LXR0-xR00 at test current, Tj=85ºC.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 7
Light Output Characteristics

Figure 3: Typical normalized light output vs. junction temperature for LXRx-xxxx at test current, Tj=85ºC.

Figure 4a: Typical normalized light output vs. forward current for LXRx-Sxxx at test current, Tj=85ºC.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 8
 Figure 4b: Typical normalized light output vs. forward current for LXRx-Rxxx at test current, Tj=85ºC.

Figure 4c: Typical normalized light output vs. forward current for LXRx-Qxxx at test current, Tj=85ºC.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 9
Forward Current Characteristics

Figure 5a: Typical forward current vs. forward voltage for LXRx-Sxxx at Tj=85ºC.

Figure 5b: Typical forward current vs. forward voltage for LXRx-Rxxx at Tj=85ºC.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 10
 Figure 5c: Typical forward current vs. forward voltage for LXRx-Qxxx at Tj=85ºC.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 11
Radiation Pattern Characteristics

Figure 6: Typical radiation pattern for LXRx-xxxx at test current, Tj=85ºC.

Figure 7: Typical polar radiation pattern for LXRx-xxxx at test current, Tj=85ºC.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 12
Product Bin and Labeling Definitions

Decoding Product Bin Labeling

In the manufacturing of semiconductor products, there are variations in performance around the average values given in the
technical datasheet. For this reason, Lumileds bins LED components for luminous flux or radiometric power, color point, peak or
dominant wavelength and forward voltage.

Reels with LUXEON M White LEDs are labeled using a 4-digit alphanumeric CAT code following the format below:

A B C D

A – designates luminous flux bin (example: M=630 to 680 lumens, T=970 to 1040 lumens)

B – designates color bin (example: 1=6500K, 2=5700K, 3=5000K, 5=4000K, 6=3500K, 7=3000K, 8=2700K)

C – designates color space (example: 5=5-step MacAdam Ellipse, 3=3-step MacAdam Ellipse)

D – designates forward voltage bin (example: F, G, H)

Therefore, a white LUXEON M with a lumen range of 630 to 680, color of 3000K, 5-step MacAdam ellipse and a forward voltage
range of 2.63 to 2.75V for 3 volt parts has the following CAT code:

M 7 5 F

Reels of LUXEON M Royal Blue LEDs are labeled using a 3-digit alphanumeric CAT code following the format below:

A B C

A – designates radiometric power bin (example: B=4200 to 4400mW, D=4600 to 4800mW)

B – designates dominant wavelength bin (example: 5=450 to 455nm, 6=455 to 460nm)

C – designates forward voltage bin (example: F, G, H)

Therefore, a Royal Blue LUXEON M with a radiometric power range of 4200 to 4400mW, peak of dominant wavelength 450 to
455nm a forward voltage range of 11.50 to 11.70V for 12 volt parts has the following CAT code:

B 5 H

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 13
Luminous Flux Bins
Table 5 lists the standard photometric luminous flux bins for LUXEON M emitters. Although several bins are outlined, product
availability in a particular bin varies by production run and by product performance. Not all bins are available in all CCTs.

Table 5. Luminous flux bin definitions for LUXEON M White.

LUMINOUS FLUX (lm)
BIN
MINIMUM MAXIMUM
J 510 550
K 550 590
L 590 630
M 630 680
N 680 730
P 730 780
Q 780 840
R 840 900
S 900 970
T 970 1040
U 1040 1120
V 1120 1200
W 1200 1290
Notes for Table 5:
1. Lumileds maintains a tolerance of ±6.5% on luminous flux measurements.

Radiometric Power Bins

Table 6. Radiometric power bin definitions for LUXEON M Royal Blue.
RADIOMETRIC POWER (mW)
BIN
MINIMUM MAXIMUM
A 4000 4200
B 4200 4400
C 4400 4600
D 4600 4800
E 4800 5000
Notes for Table 6:
1. Lumileds maintains a tolerance of ±6.5% on radiometric power measurements.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 14
Color Bin Definition

Figure 8: 3- and 5-step MacAdam ellipse illustration for Table 7.

Table 7. 3- and 5-step MacAdam ellipse color bin definitions for LUXEON M.
CENTER POINT MAJOR AXIS, MINOR AXIS, ELLIPSE ROTATION
NOMINAL CCT COLOR SPACE
(cx, cy) a b ANGLE, Θ
2700K Single 3-step MacAdam ellipse 0.4578, 0.4101 0.00810 0.00420 53.70
3000K Single 3-step MacAdam ellipse 0.4338, 0.4030 0.00834 0.00408 53.22
3500K Single 3-step MacAdam ellipse 0.4073, 0.3917 0.00927 0.00414 54.00
4000K Single 3-step MacAdam ellipse 0.3818, 0.3797 0.00939 0.00402 53.72
5000K Single 3-step MacAdam ellipse 0.3447, 0.3553 0.00822 0.00354 59.62
3000K Single 5-step MacAdam ellipse 0.4338, 0.4030 0.01390 0.00680 53.22
4000K Single 5-step MacAdam ellipse 0.3818, 0.3797 0.01565 0.00670 53.72
5000K Single 5-step MacAdam ellipse 0.3447, 0.3553 0.01370 0.00590 59.62
5700K Single 5-step MacAdam ellipse 0.3287, 0.3417 0.01243 0.00533 59.09
6500K Single 5-step MacAdam ellipse 0.3123, 0.3282 0.01115 0.00475 58.57
Notes for Table 7:
1. Lumileds maintains a tolerance of ±0.005 on x and y coordinates in the CIE 1931 color space.

Dominant Wavelength Bins

Table 8. Dominant wavelength bins for LUXEON M Royal Blue.
DOMINANT WAVELENGTH (nm) [1]
BIN
MINIMUM MAXIMUM
4 445 450
5 450 455
6 455 460
Notes for Table 8:
1. Lumileds maintains a tolerance of ±0.5nm on dominant wavelength measurements.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 15
Forward Voltage Bins
Table 9. Forward voltage bin definitions for LUXEON M.
FORWARD VOLTAGE (V) [1]
PART NUMBER BIN
MINIMUM MAXIMUM
F 10.50 11.00
LXRx-SWxx
G 11.00 11.50
and LXR0-SR00
H 11.50 11.70
F 5.25 5.50
LXRx-RWxx
G 5.50 5.75
and LXR0-RR00
H 5.75 6.00
F 2.63 2.75
LXRx-QWxx
G 2.75 2.88
and LXR0-QR00
H 2.88 3.00
Notes for Table 9:
1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.

Mechanical Dimensions

7.00±0.12

3.75±0.12
3.50±0.15

3.14±0.10 R0.20±0.04
0.56±0.08

3.50±0.15
3.14±0.10

7.00±0.12

6.40 0.06

Figure 9: Mechanical dimensions for LUXEON M.

Notes for Figure 9:

1. Drawings are not to scale.
2. All dimensions are in millimeters.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 16
Reflow Soldering Guidelines

tp
Tp

Critical Zone
Ramp-up TL to Tp

TL
tL
Temperature

Tsmax

Tsmin
Ramp-down
ts
Preheat Area

25
Time 25ºC to Peak
Time JEDEC J-STD-020D

Figure 10: Visualization of the acceptable reflow temperature profile as specified in Table 10.

Table 10. Reflow profile characteristics for LUXEON M.

PROFILE FEATURE LEAD-FREE ASSEMBLY

Preheat Minimum Temperature (Tsmin) 150°C

Preheat Maximum Temperature (Tsmax) 200°C
Preheat Time (tsmin to tsmax) 60 to 120 seconds
Ramp-Up Rate (Tsmax to Tp) 3°C / second maximum
Liquidus Temperature (TL) 217°C
Time Maintained Above Temperature TL (tL) 60 to 150 seconds
Peak / Classification Temperature (Tp) 260°C
Time Within 5°C of Actual Temperature (tp) 20 to 40 seconds
Ramp-Down Rate 6°C / second maximum
Time 25°C to Peak Temperature 8 minutes maximum

Notes for Table 10:

1. All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package body.

JEDEC Moisture Sensitivity

Table 11. Moisture sensitivity levels for LUXEON M.
FLOOR LIFE SOAK REQUIREMENTS STANDARD
LEVEL
TIME CONDITIONS TIME CONDITIONS
1 Unlimited ≤30°C / 85% RH 168 Hours +5 / -0 85°C / 85% RH

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 17
Solder Pad Design

Figure 11: Recommended PCB solder pad layout for LUXEON M.

Notes for Figure 11:

1. Drawings are not to scale.
2. All dimensions are in millimeters.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 18
Packaging Information

Pocket Tape Dimensions

DIRECTION OF FEED

12.00mm POCKET PITCH

4.99 4.59
1.59 1.50
B B

4°
16.00
7.50

1.50 2.00
1.75
4.00mm INDEX HOLE PITCH

0.38 8°
7.35 SQ.

4.49 4.11 4.99

SECTION B-B
SCALE 2 : 1
5.35

-DEVICE ORIENTATION-
NON-FIDUCIAL CORNER
LOCATEDAS SHOWN

F
DETAIL E
SCALE 4 : 1
-LOADED POCKETS-
500 -TAPE END-
-LEADER- 30 EMPTY POCKETS
50 EMPTY POCKETS

EF

DIRECTION OF FEED

Figure 12: Pocket Tape dimensions for LUXEON M.

Notes for Figure 12:

1. Drawings are not to scale.
2. All dimensions are in millimeters.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 19
Reel Dimensions

20.8mm OUTSIDE WIDTH

16.4mm INSIDE WIDTH

330.00 REEL DIAMETER

13.00mm ARBOR
HOLE DIAMETER

COVER TAPE

DIRECTION OF FEED

CARRIER TAPE TAPE REEL

Figure 13: Reel dimensions for LUXEON M.

Notes for Figure 13:
1. Drawings are not to scale.
2. All dimensions are in millimeters.

DS103 LUXEON M Product Datasheet 20150820 ©2015 Lumileds Holding B.V. All rights reserved. 20
About Lumileds
Lumileds is the light engine leader, delivering innovation, quality and reliability.

For 100 years, Lumileds commitment to innovation has helped customers pioneer breakthrough products in the automotive,
consumer and illumination markets.

Lumileds is shaping the future of light with our LEDs and automotive lamps, and helping our customers illuminate how people
see the world around them.

To learn more about our portfolio of light engines, visit lumileds.com.

©2015 Lumileds Holding B.V. All rights reserved. Neither Lumileds Holding B.V. nor its affiliates shall be liable for any kind of loss of data or
LUXEON is a registered trademark of the Lumileds Holding B.V. any other damages, direct, indirect or consequential, resulting from the use of the provided
in the United States and other countries. information and data. Although Lumileds Holding B.V. and/or its affiliates have attempted to
provide the most accurate information and data, the materials and services information and data
lumileds.com are provided “as is,” and neither Lumileds Holding B.V. nor its affiliates warrants or guarantees
the contents and correctness of the provided information and data. Lumileds Holding B.V. and its
affiliates reserve the right to make changes without notice. You as user agree to this disclaimer
and user agreement with the download or use of the provided materials, information and data.
DS103 LUXEON M
Product Datasheet 20150820