Impact of drainage of organic soils in forest land on soil carbon (C) stock changes is of high interest not only to accurately estimate soil C stock changes, but also to provide scientifically based recommendations for forest land management in context of climate change mitigation. To improve knowledge about long-term impact of drainage on nutrient-rich organic soils in hemiboreal forests in Latvia, 50 research sites representing drained conditions (Oxalidosa turf. mel. (Kp) and Myrtillosa turf. mel. (Ks) forest site types) and undrained conditions as control areas (Caricoso-phragmitosa, Dryopterioso-caricosa and Filipendulosa forest site types) were selected. Soil C stock changes after drainage was evaluated by comparing current C stock in drained organic soils to theoretical C stock before drainage considering impact of soil subsidence. During the 53-years period after drainage, the peat subsidence was higher in nutrient-rich Kp forest site type compared to moderate nutrient-rich Ks forest site type (peat subsided by 37.0 ± 4.8 and 23.3 ± 4.8 cm, respectively). In nutrient-rich Kp forest site type, soil C stock decreased by 4.98 ± 1.58 Mg C ha-1 yr-1 after drainage, while no statistically significant changes in soil C stock (0.19 ± 1.31 Mg C ha-1 yr-1) were observed in moderate nutrient-rich soils in Ks forest site type. Thus, in Ks forest site type, the main driver of the peat subsidence was the physical compaction, while in Kp forest site type contribution of organic matter decomposition and consequent soil C losses to subsidence of the peat was significant.
Mechanical site preparation (MSP) is deliberate soil disturbance which is undertaken to improve the conditions for forest regeneration. Disc trenching and mounding are the dominant MSP practices currently used in Sweden and Finland. In this paper, the impacts of MSP on the soil, water quality, greenhouse gas (GHG) emissions and ground vegetation of mineral soil sites in Sweden and Finland are reviewed. The practices considered are patch scarification, mounding, inverting, disc trenching, and ploughing, which together represent a wide range of soil disturbance intensity. The environmental effects of MSP in this region have not been studied extensively. The environmental impact of MSP derives from the process of creating microsites which involves horizontal and/or vertical redistribution of soil and soil mixing. This typically affects decomposition, element circulation and leaching, vegetation coverage and uptake of nutrients and water, and possibly erosion and sediment exports. Following disc trenching or mounding the effects on GHG emissions appear to be minor over the first two years. For a few years after disc trenching concentrations in soil water collected below ridges are higher than that below furrows for some elements (e.g., NO3-, NH4+, Mg2+, and total or dissolved organic C). The physical and chemical effects of ploughing remain detectable for several decades. There is little evidence about how the effects of forestry activities in upland areas on soil-water chemistry are transferred to adjacent surface water bodies, including what role streamside discharge areas play. MSP increases the tree biomass C store and may increase the total ecosystem C store. The impact of MSP on the cover and abundance of ground vegetation species depends on the composition of the original plant community, MSP intensity, and the establishment rate of different species. Species cover generally seems to decline for late succession understory species, while pioneer and ruderal species can benefit from the microsites created. Areas containing lichens which are used for reindeer forage require special consideration. More research is needed on the environmental effects of MSP, particularly regarding its long-term effects. Further efforts should be made to develop efficient site-preparation practices which better balance the disturbance intensity with what is needed for successful regeneration.
The productivity of cut-to-length machine operators exhibits a significant disparity, with the most productive individuals demonstrating twice the efficiency of their less productive counterparts. This discrepancy is largely attributed to variations in work methods. While supervised training has proven effective in streamlining work methods and enhancing productivity, the availability of forest-machine instructors for supervision is limited. Intelligent coaching systems (ICS) are periodically proposed to address this constraint. ICS are computer-based aids that offer machine operators real-time feedback on their work and guide them on how to rationalize their work. The successful implementation of ICS initially requires the development of systems for automatic work-element detection (AWED). Therefore, this article explores the history, current status, and technological possibilities of AWED. Additionally, key features of ICS are briefly reviewed. Lastly, a broader, interdisciplinary discussion is initiated on how to strategically allocate limited research resources. Questions surrounding the feasible ambition level for ICS and AWED are raised, prompting considerations for the next steps in research and development.