1/50 Churchill MkIII Tanks for the Dieppe Raid

 

These models were posted to the Analogue Hobbies Painting Challenge blog back in March, but I wanted to post them on our blog here as well. Anyway it's four 1/50 Corgi Churchill MkIII medium tanks, as seen (kind of) on the infamous Dieppe raid of 19 August 1942.

The four vehicles I've done are all Churchills of The Calgary Regiment (Calgary Tanks), aka 14 Canadian Armoured Tank Regiment (14 CATR). I had three of these painted already in a standard British armour green, but for Christmas was given another stock Corgi model by Challenger DaveV, which prompted me to revisit the three I'd already painted...

 

So I got the project underway in earnest, first re-priming all four models with flat black spray, researching the correct colour for the Canadian armour at Dieppe (turns out it was described as "dog sh!t brown" and I used GW Steel Legion Drab to replicate that), and sourcing decals for the tanks. I got these from Peddinghaus, a cottage supplier in Germany that makes a ton of very cool and obscure decals in 1/72 and 1/48 scale.

 

I also figured I may as well do some conversions on the tanks to better replicate their Dieppe configuration (because why not, right?) This involved scratch-building the exhaust pipe extensions that allowed the Churchills to deep-wade without allowing water into the engines. This was characteristic of the Dieppe Churchills and is seen on every photographed example. 

I made the extensions out of thick flexible wire (I think it's maybe soldering wire) bent to shape and superglued to the exhaust pipes of the tank. I then ran thread between the upper ends of the extensions as shown in photographs of the vehicles on the beach. The extensions were then heavily weathered with rust effect wash.

  

Unfortunately none of the Churchills at Dieppe were equipped with track guards for the upper runs, as seen on these Corgi models... sadly I don't think anyone makes appropriate models in 1/48 or 1/50 and taking a grinder to these models to remove the guards wasn't really in the project remit.

I decided to portray the three vehicles of 9 Troop, B Squadron - Bluebell, Blossom, and Buttercup, as well as the troop leader of 6 Troop, Bob (all four were Churchill MkIIIs). The decals from the Peddinghaus set are excellent and have great detail. However they did take a good deal of work to fit, as they are not "pre-cut" and need to be trimmed to size. There's also 15 decals for each vehicle!

I didn't do a ton of weathering on the vehicles as this would be the first time they were in action - just some light water streaking down the vertical panels, and dust along the lower part of the vehicles and suspension.

 

Here's a close-up of the exhaust extensions. Honestly they were a bit of a futz to build but I like the way they turned out - they really give the tanks the "Dieppe look":

I'm actually quite happy with the way these turned out. This year marks the 80th anniversary of the Dieppe raid and I am looking forward to setting up a game this summer to mark it. We've played Dieppe games a few times before (but not for years) but I think the new Churchills are really going to add to the vibe.

Stay tuned for some more Dieppe armour...

Challenge Submission #13 - A Handful of Special Challenge Targets

 One of the features of this year's Analogue Hobbies Painting Challenge is the Challenge Quadrant, consisting of three rings of planets surrounding a central star, each planet representing a special theme for the figures to be painted. Here are some of those special figures that I completed in late January and early February.

 The figures of Gandalf the White on foot and mounted on Shadowfax are the older Games Workshop Lord of the Rings castings. I have included Gandalf the Grey in the photos for the 'Before' and 'After' comparison.

A Canadian Churchill tank at Dieppe -Churchill Mk III T68696 'CAT' is a repainted 1/50 Solido diecast model I acquired from a friend. It was originally painted in a desert yellow/olive green striped camouflage pattern for service in Tunisia, but I wanted it to match another Solido Churchill that I had that depicted 'Cheetah' (shown in the background). So the 'tank from Tunisia' was repainted using Vallejo Dark Earth, and then the vehicle name, numbers, etc. painted on freehand.

 A legionary of early Imperial Rome, equipped with lorica segmentata, gladius, and scutum. This is a 28mm plastic figure that came as a sample years ago with an issue of Wargames Illustrated. I was never sure what to do with it, and thought I might use it as a gladiator in our 'local arena'. I'm glad I had it on hand for one of the stops on the Challenge Quadrant.

 A Eurasian Solar Union SAW gunner from Ground Zero Games and a Rebel Commando from West End Games. Both date from the mid to late 1990's. I have painted them up in the colour scheme for the Ral Partha Galactic Grenadiers figures I use as 'Planetary Militia'. In the past I have used both GZG and WEG minis to augment the variety of poses and weapons in my squads.

 

 A 54mm miniature from the Scale Link Ltd. WW1 Grand Guerre range, which depicts a British or Canadian infantryman advancing at the 'Trail Arms' position with fixed bayonet, and his Small Box Respirator worn at the 'Alert' position. He is identified as a member of the 27th Battalion CEF by the blue circle over a blue rectangle on his shoulder. The figure was painted using Vallejo acrylics, followed by some Games Workshop washes. Finally some AK Interactive Spattereffects 'Wet Mud' was applied to areas like knees and elbows. 

  Two 'old school' 25mm Star Wars figures from West End Games depicting Princess Leia Organa as she appeared in 'A New Hope' and 'Return of the Jedi'. Again, these are painted using Vallejo acrylics with GW washes on the faces and hands, and to produce the camouflage pattern on the poncho.

 These special challenges have been very useful in clearing out some of the miniatures that have been lingering in the 'PENDING' box for some time.

Thanks for reading.

Challenge Submission #11 - A Mixed Bag of WW2 Vehicles

I had a hard time focusing during the last week of January, ricocheting around from project to project without seeming to get closer to completion. Eventually things started falling into place, and I ended up with 9 completed vehicles. Some of these have been sitting in my 'IN' box for over a decade, so it felt good to finally get them ready for the gaming table.

First up is a DUKW with a British RASC driver. This was a toy dating from the 1960s that originally belonged to my younger brother. It suffered some 'battle damage' at some point, and my brother was no longer interested in it. I thought I might be able to fix it, and it seemed like the right scale for 28mm gaming. In fact, measuring its length and comparing it to the length of an actual DUKW, it works out to be 1/56. The only 'flaw' is that it only has a single axle in the rear instead of two. I have no idea who manufactured it, but it reads 'NOVELTY' and 'Made in Hong Kong' on the bottom. 

 

The broken pieces near the back and the front right wheel well were filled in using epoxy putty, while the front windshield was fashioned from pieces of clear plastic cut from a CD case. The crates and fuel drums came from a Bandai Maultier kit, and the driver is an old Bolt Action jeep driver that I had in my 'bits box' along with the rolled up tarp. It is now ready to ferry supplies or a squad of commandos across a river or from ship to shore.

 

Next up is a Kübelwagen Type 82/3. This was a mock-up scout car/armoured vehicle with a machine gun-turret atop the cabin. It was apparently built for decoy and training purposes. I bought this from Wargames Foundry decades ago. It came with the Feldgendarm, but I only painted up the 'Kettenhund' as I couldn't decide the colour scheme that would be most appropriate. Eventually I thought Panzer Dunkelgrau would do just as well as any other colour, and now it's finally done.

 

 Third on our list is a Bandai 1/48 SdKfz 3 Maultier that I picked up off Ebay. This was another project where I couldn't decide what colour to paint it, but I finally decided to go with Panzer Dunkelgrau with an Olive Green striped camouflage suitable for the Russian Front. The tarp was painted Tan Earth and given a wash of GW Agrax Earthshade. I then liberally applied Vallejo European Dust wash everywhere. The kit came with a cargo of four petrol drums and two large crates, but since nobody would see them with the tarp in place, I used them for the DUKW.

 

 Next is a 3D printed French Panhard 178 armoured car that was from the same run as the two painted by Fellow Conscript DallasE. I used a different paint scheme that is based on a surviving example in the Musée des Blindés in Saumur, France. I used Vallejo Gunship Green and Chocolate Brown with a sharp black line in between. I left off the fifth wheel, but added a muffler on the right side made from a piece of plastic sucker stick. Sometimes it helps a recce unit to not be heard, as well as not be seen. The decals were all ones that were kicking around in my files, so I didn't have to free hand any roundels. 

 

The fifth item is a group of four M5 Half-tracks to provide some additional armoured lift capability to my 2nd Canadian Division. I am not sure if these were used in any of the infantry divisions, so I may have to mark them up for the 4th Canadian Armoured Division. The models are either Corgi or Solido 1/50 vehicles that all came in different colours and configurations. One was an ambulance version that had a tarp on it, and the back door was cut out. The tarp was tossed in the 'bits box' while the missing door was replaced using thin plastic card. Everything was painted a uniform colour and then 'muddied up'. The verdict is still out on what stars should be added and where, but the vehicles are now ready to take to the field and move a platoon of infantry in relative safety on the battle field.

 

 The last vehicle of this post is a Warlord Games 1/56 resin and metal M10 Achilles mounting a 17 pounder. While this is a newer acquisition compared to some of the other vehicles, it sat on the shelf for a while before being assembled. When it arrived, the tracks were warped and didn't form a clean fit with the chassis. A bath in some boiling water and some careful pressure in the right places straightened things out to an acceptable degree and things proceeded readily from there. Two of the crew in the turret are part of the resin casting while the third crewman is in metal. All came with separate heads which can provide some variety if you want to field more than one. The tarps were added from my 'bits box'. 

The only two Canadian units that used 17pdr M-10s were the 4th Anti-Tank Regiment RCA of the 5th Canadian Armoured Division; and the 7th Anti-Tank Regiment RCA of the 1st Canadian Corps Artillery. Both Regiments would have had two batteries of towed 17pdrs and two SP batteries with 17pdr M-10s

 

 As I said in the title, it is definitely a mixed bag of vehicles, but they are now all done.Thanks for reading.

 

Challenge Submission #5 - За Родину (For the Homeland) WW2 Soviet Armour

Since I had painted up a large force of German armoured vehicles in an earlier submission, Stalin was starting to look at the Molotov–Ribbentrop Pact with growing suspicion. It was now time to increase the Red Army's tank arm. Ready for this week's report are the following: a BA-20 armoured car, a trio of BT-7 fast tanks, a KV-1, and a Lend-Lease M10 Wolverine.

First up is a BA-20 armoured car, which is a 1/48 scale plastic kit from Ace Models out of Kyiv. I did another model by this company in my first submission as part of my early war Polish Army reinforcements. I found these kits to be finely detailed, but a bit fiddly to put together. Instead of the body being a one- or two-piece molding, it consisted of separate eight pieces. After assembly, the vehicle was primed black with a rattle can, and given a base coat of Russian Green. This was followed by some drybrushing along raised surfaces and edges with Vallejo Olive Green. After the decals were applied, it got a wash of Vallejo European Dust.

 

Up next is a platoon of three 1/56 scale BA-7 fast tanks from Warlord Games. The Soviets produced over 5700 of these between 1935 and 1940, and in 1941 it was the main cavalry tank of the Soviet army. However some 2000 were lost during the first 12 months on the Eastern Front.  These are resin castings with metal gun barrels and turret hatches. The castings were very clean, and came as just two pieces - the body of the tank, including all the tracks and road wheels, and the turret. The kits all included a metal tank commander of which I used one. They also included flame and smoke markers consisting of a wooden base and some coloured wool in white, black, and orange-red to glue on. They were painted in a similar manner to the BA-20 armoured car.

 

 Now we have the "Russischer Koloss" or "Russian Colossus", the mighty KV-1 heavy tank. The Soviets produced over 5,000 of these between 1939 and 1943, with about 500 in service at the start of Operation Barbarossa. This is another 1/48 scale model, this time from Hobby Boss. When first looking at the kit, especially with all the separate track pieces, I was a bit intimidated. However it went together very smoothly, and had a lot of interesting details such as etched brass parts, and fine twisted copper wire for the tow cables. The painting technique I used was the same as with the previous vehicles. I used one of the three options for decals provided by the kit, specifically that of the 12th Guards Armoured Regiment, 1st Moscow Mechanized Division, August 1942.

 

Lastly I did a Lend-Lease M10 Wolverine, which is a repainted 1/50 scale Solido diecast model that I was given by fellow Conscript DaveV. I already had a 1/56 scale resin model of the M10 Achilles with a 17-pounder from Warlord Games, and the size disparity was too great for me to ever field the two models on the table together. The solution was to send the Solido M10 to the Eastern Front. Approximately 52 M10s were supplied to the Soviet Union through Lend-Lease. They were used to form two self-propelled artillery regiments. The first was the 1223rd Self-propelled Artillery Regiment of the 29th Tank Corps, part of the 5th Guards Tank Army. This unit served on the 3rd Belorussian Front in 1944, taking part in summer campaigns in Belorussia, the Baltic, and East Prussia. The 1239th Self-propelled Artillery Regiment was part of the 16th Tank Corps, 2nd Tank Army. It fought in Belorussia and Poland in 1944.

Painting this vehicle was pretty much as per the rest of the vehicles in this post. The only change was the addition of a gun crew, which was needed due to the open-topped turret. The three crewmen were converted from some spare Soviet tank crew that were left over from a Bandai T34 kit plus two sets of 'seated legs' left over from some unused Panzer crews. I also added a .50 cal machine gun from my bits box.  In the end, I had to trim a little off the bottom of their legs so that they would all fit in the turret. I am pretty pleased with the way they all came together.

 

Thanks for reading.