When I leave work Monday morning, I have 1½ week off, until Wednesday night in week 43, so I expect to get my second batch of jungle bases moving and finished, so that I can use the dinner table for some gaming (and dining, og course); it has been occupied by spread newspapers and boxes for far too long.
Showing posts with label Cargo. Show all posts
Showing posts with label Cargo. Show all posts
Monday, 15 October 2018
3D Printed: A Bunch of Star Wars Containers
I have quite a collection of 'Medium Cargo Containers' by now - and I also printed some Kyber Crystal Containers, to have something to use as portable objectives.
When I leave work Monday morning, I have 1½ week off, until Wednesday night in week 43, so I expect to get my second batch of jungle bases moving and finished, so that I can use the dinner table for some gaming (and dining, og course); it has been occupied by spread newspapers and boxes for far too long.
When I leave work Monday morning, I have 1½ week off, until Wednesday night in week 43, so I expect to get my second batch of jungle bases moving and finished, so that I can use the dinner table for some gaming (and dining, og course); it has been occupied by spread newspapers and boxes for far too long.
Saturday, 13 October 2018
3D Printed: Medium Sized Cargo Container
Not my first attempt at this print, but probably the nicest one.
The STL can be found here on Thingiverse.
I am trying to organize the stuff I have painted for Legion into some boxes in a larger cardboard crate, and I shall be taking some more photos of stuff I have not shown, yet, over the next couple of days (there is actually quite a back-log, regarding blog posts).
The STL can be found here on Thingiverse.
I am trying to organize the stuff I have painted for Legion into some boxes in a larger cardboard crate, and I shall be taking some more photos of stuff I have not shown, yet, over the next couple of days (there is actually quite a back-log, regarding blog posts).
Thursday, 11 October 2018
3D Printed: More Star Wars Crates
I have had some problems with a recently purchased roll of blue PLA filament, and I am now churning out small bits and bobs to tune a profile for handling it.
At the front you can see one of the weird results - I am keeping that one, because I think I can paint it as if burning, but I have had to chuck quite a few pieces. They are turning out OK, now, and I have started a medium sized cargo container which should finish about 7:30 tomorrow morning.
At the front you can see one of the weird results - I am keeping that one, because I think I can paint it as if burning, but I have had to chuck quite a few pieces. They are turning out OK, now, and I have started a medium sized cargo container which should finish about 7:30 tomorrow morning.
Sunday, 2 September 2018
3D Printed: Star Wars Scatter Terrain
Smaller pieces to populate the Star Wars Legion table printed so far (the Imperial bunker and the power-thingies not included). Everything off Thingiverse.
Currently printing a 30cm redwood (jungle/Endor), and when it finishes this evening, I shall have to change filament to a lighter grey for printing some additional commission pieces for Imperial Assault.
Later this week I shall try my largest print so far, an escape pod, scaled up from a Thingiverse X-wing scale model (I ordered C-3PO, and R2-D2, yesterday, and am going to make a large dune with an indent for the escape pod, so I can stage an Ep. IV Tatooine display).
Currently printing a 30cm redwood (jungle/Endor), and when it finishes this evening, I shall have to change filament to a lighter grey for printing some additional commission pieces for Imperial Assault.
Later this week I shall try my largest print so far, an escape pod, scaled up from a Thingiverse X-wing scale model (I ordered C-3PO, and R2-D2, yesterday, and am going to make a large dune with an indent for the escape pod, so I can stage an Ep. IV Tatooine display).
Subscribe to:
Comments (Atom)